Matrix RB209 取扱説明書

2

3

14

25

36

47

58

69

ENGLISH

󳟑󵑤󰞽󱼗

󱽵󲂼󴐮

󺘒󷸣󹙪





󰁵󰃕󰁲󰂏󰂭󰃀

3

ENGLISH

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

• When using Matrix Cycles, basic precautions should always be followed, including the following: Read all instructions before using this equipment. It

is the responsibility of the owner to ensure that all users of this equipment are adequately informed of all warnings and precautions.

• This equipment is for indoor use only. This training equipment is a Class S product designed for use in a commercial environment such as a ﬁtness facility.

DANGER!

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

• Always unplug the equipment from the electrical outlet before cleaning, performing maintenance and putting on or taking o parts.

CAUTION!

CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE.

• It is essential that this equipment is used only indoors, in a climate controlled room. If this equipment has been exposed to colder temperatures or high moisture climates,

it is strongly recommended that the equipment is warmed up to room temperature and allowed time to return to lower humidity levels before ﬁrst time use.

WARNING!

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Use this exercise cycle for its intended

purpose as described in this manual.

• Never operate the exercise cycle if it is not

working properly, or if it has been damaged.

Contact Customer Tech Support or the authorized

dealers for examination and repair.

• Do not use the exercise cycle without proper footwear.

NEVER operate the exercise cycle with bare feet.

• Do not wear any clothing that might catch on

any moving parts of this exercise cycle.

• Keep hands and feet clear at all times from moving parts

to avoid injury. Never turn the pedal cranks by hand.

• Do not dismount the exercise cycle until

the pedals are at a complete STOP.

• Do not attempt to ride the exercise

cycle in a standing position.

• Do not insert any object, hands or feet into any openings,

or expose hands, arms or feet to the drive mechanism

or other potentially moving part of the exercise cycle.

• Do not use any equipment that is damaged or has worn

or broken parts. Use only replacement parts supplied

by Customer Tech Support or the authorized dealers.

• Do not operate where aerosol (spray) products are

being used or when oxygen is being administered.

• Close supervision is necessary when used near children.

• This equipment is not intended for use by persons with

reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

equipment by a person responsible for their safety.

• Ensure that adjustment levers (seat and handlebar

fore-and-aft) are properly secured and do not

interfere with range of motion during exercise.

• Incorrect or excessive exercise may result in serious

injury or death. If you experience any kind of pain,

including but not limited to chest pains, nausea, dizziness,

or shortness of breath, stop exercising immediately

and consult your physician before continuing.

• Do not jump on the unit.

• At no time should more than one person

be on unit while in operation.

• This unit should not be used by persons weighing more

than speciﬁed in the OWNER’S MANUAL SPECIFICATIONS

SECTION. Failure to comply will void the warranty.

• Keep power cord away from heated surfaces. Do not carry

this unit by its supply cord or use the cord as a handle.

• Do not use other attachments that are not recommended

by the manufacturer. Attachments may cause injury.

• Use the unit only as described in the

unit guide and owner’s manual.

• Disconnect all power before servicing or moving

the equipment. To clean, wipe surfaces down

with soap and slightly damp cloth only; never

use solvents. (See MAINTENANCE)

• At NO time should pets or children under the

age of 14 be closer to the unit than 10 feet.

• At NO time should children under the age of 14 use the unit.

• Children over the age of 14 should not use

the unit without adult supervision.

• Never operate the unit if it has a damaged cord or plug,

if it is not working properly, if it has been dropped

or damaged, or immersed in water. Return the unit

to a service center for examination and repair.

• To avoid the risk of electric shock, this piece

of equipment must only be connected to a

circuit with non-looped (isolated) ground.

• To disconnect, turn all controls to the o

position, then remove plug from outlet.

• Do not remove the console covers unless instructed

by Customer Tech Support. Service should only

be done by an authorized service technician.

• Heart rate monitoring systems may be inaccurate.

4

POWER REQUIREMENTS

DEDICATED CIRCUIT AND ELECTRICAL INFO

A “Dedicated Circuit” means that each outlet you plug into should not have

anything else running on that same circuit. The easiest way to verify this is

to locate the main circuit breaker box, and turn o the breaker(s) one at a

time. Once a breaker has been turned o, the only thing that should not have

power to it are the units in question. No lamps, vending machines, fans, sound

systems, or any other item should lose power when you perform this test.

Non-looped (isolated) neutral/grounding means that each circuit must have an individual

neutral/ground connection coming from it, and terminating at an approved earth

ground. You cannot “jumper” a single neutral/ground from one circuit to the next.

ELECTRICAL REQUIREMENTS

For your safety and to ensure good unit performance, the ground on this circuit must

be non-looped (isolated). Please refer to NEC article 210-21 and 210-23. Any alterations

to the standard power cord provided could void all warranties of this product.

Units with LED and Premium LED consoles are designed to be self powered

and do not require an external power supply source to operate. Without an

external power supply, the console’s start-up time may be delayed. Add-on

TV’s and other console accessories will increase the time needed for start-

up. An external power supply will ensure power is provided to the console

at all times and is recommended when add-on accessories are used.

For units with an integrated TV (Touch), the TV power requirements are included

in the unit. An RG6 quad shield coaxial cable with ‘F Type’ compression ﬁttings

on each end will need to be connected to the cardio unit and the video source.

Additional power requirements are not needed for the add-on digital TV.

NOTE: All units with Virtual Active

™

must be powered.

110 V UNITS

110 V units require the use of a 100-125 V, 60 Hz

and a 15 A “Dedicated Circuit”, with a non-looped

(isolated) neutral/ground for power. This outlet should

be a NEMA 5-15R and have the same conﬁguration

as the plug. No adapter should be used with this

product. These cycles can be daisy-chained together

with up to 4 units per 15 A dedicated circuit. Matrix

daisy-chain cord adapters are sold separately.

GROUNDING INSTRUCTIONS

The unit must be grounded. If it should malfunction or breakdown, grounding provides

a path of least resistance for electric current to reduce the risk of electric shock. The unit

is equipped with a cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances. If the user does not follow

these grounding instructions, the user could void the Matrix limited warranty.

ADDITIONAL ELECTRICAL INFO

In addition to the dedicated circuit requirement, the proper gauge wire must be used

from the circuit breaker box, to each outlet that will have the maximum number of units

running o of it. If the distance from the circuit breaker box to each outlet, is 100 ft (30.5

m) or less, then 12 gauge wire should be used. For distances greater than 100 ft (30.5

m) from the circuit breaker box to the outlet, a 10 gauge wire should be used.

ENERGY SAVING / LOW-POWER MODE

All units are conﬁgured with the ability to enter into an energy saving / low-power mode when

the unit has not been in use for a speciﬁed period of time. Additional time may be required to

fully reactivate this unit once it has entered the low-power mode. This energy saving feature

may be enabled or disabled from within the ‘Manager Mode’ or ‘Engineering Mode.’

ADD-ON DIGITAL TV

Additional power requirements are not needed for the add-on digital TV.

An RG6 coaxial cable with ‘F Type’ compression ﬁttings will need to be

connected between the video source and each add-on digital TV unit.

FCC REGULATIONS (USA ONLY)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

ENGLISH

North American and

European power cord

plugs shown. Depending

on your country, the plug

type may vary.

110 NEMA 5-15P

PLUG (N.A.)

EURO PLUG

(EUROPE)

5

ASSEMBLY

UNPACKING

Unpack the equipment where you will be using it. Place the carton

on a level ﬂat surface. It is recommended that you place a protective

covering on your ﬂoor. Never open box when it is on its side.

IMPORTANT NOTES

During each assembly step, ensure that ALL nuts and

bolts are in place and partially threaded.

Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe

this o. If you have diculty, a light application of lithium grease is recommended.

WARNING!

There are several areas during the assembly process that special attention must be

paid. It is very important to follow the assembly instructions correctly and to make

sure all parts are ﬁrmly tightened. If the assembly instructions are not followed

correctly, the equipment could have parts that are not tightened and will seem

loose and may cause irritating noises. To prevent damage to the equipment, the

assembly instructions must be reviewed and corrective actions should be taken.

NEED HELP?

If you have questions or if there are any missing parts, contact Customer

Tech Support. Contact information is located on the information card.

ENGLISH

Page

6

RECUMBENT CYCLES

Page

8

UPRIGHT CYCLES

6

D

C

TOOLS REQUIRED:

F 4 mm Allen Wrench

F 6 mm Allen Wrench

F Flat Wrench (15mm/17mm 325L)

F Phillips Screwdriver

PARTS INCLUDED:

F 1 Main Frame

F 1 Rear Stabilizer Tube

F 1 Front Stabilizer Tube

F 1 Rear Frame Handle

F 1 Rear Frame Cover

F 1 Console Mast

F 1 Console Handlebars

F 2 Handlebar Covers

F 1 Seat Frame

F 1 Water Bottle Pocket

F 1 Seat Base

F 1 Seat Back

F 1 Hardware Kit

F 1 Power Cord (packaged with console)

Console sold separately

A

B

1

Hardware Qty

A

B

Bolt

Spring Washer

8

2

Hardware Qty

C

D

Bolt

Screw

2

RECUMBENT CYCLE ASSEMBLY

ENGLISH

7

ENGLISH

O

N

M

L

H

I

E

F

G

3

Hardware Qty

E

F

G

Bolt

Tooth Washer

Screw (pre-installed)

4

Hardware Qty

H

I

Screw

Bolt

2

4

5

Hardware Qty

J

K

Bolt

Spring Washer

4

6

Hardware Qty

L

M

N

O

Bolt

Spring Washer

Arc Washer

Screw

4

3

J

K

8

ASSEMBLY COMPLETE

P

Q

R

7

Hardware Qty

P

Q

R

Bolt

Bolt (pre-installed)

Bolt

2

4

2

TOOLS REQUIRED:

F 4 mm Allen Wrench

F 6 mm Allen Wrench

F Flat Wrench (13/15 mm)

F Phillips Screwdriver

PARTS INCLUDED:

F 1 Main Frame

F 1 Rear Stabilizer Tube

F 1 Front Stabilizer Tube

F 1 Rear Frame Handle

F 1 Rear Frame Cover

F 1 Console Mast

F 1 Water Bottle Holder

F 1 Seat Base

F 1 Arm Rest Handlebars

F 1 Front Shroud Cover (pre-installed)

F 1 Rear Shroud Cover (pre-installed)

F 1 Hardware Kit

F 1 Power Cord (packaged with console)

Console sold separately

UPRIGHT CYCLE ASSEMBLY

ENGLISH

1

2

3

4

5

6

7

LCB Communication

Extension Power Wire

TV Power

Console Connect Wires

Ethernet

Coax

Ground Wire

1

7

6

5

4

3

2

9

ENGLISH

E

F

H

G

I

C

D

A

B

1

Hardware Qty

A

B

Bolt

Flat Washer

8

2

Hardware Qty

C

D

Bolt

Screw

2

3

Hardware Qty

E

F

G

H

I

Bolt

Tooth Washer

Screw (pre-installed)

Screw

Bolt

4

6

2

4

Hardware Qty

J Bolt 4

J

10

K

L

5

Pre-installed Hardware Qty

K

L

Flat Washer

Nylon Nut

3

6

Hardware Qty

M

N

Bolt (pre-installed)

Bolt

4

2

N

M

ASSEMBLY COMPLETE

ENGLISH

1

2

3

4

5

6

7

LCB Communication

Extension Power Wire

TV Power

Console Connect Wires

Ethernet

Coax

Ground Wire

1

7

6

5

4

3

2

11

BEFORE YOU BEGIN

LOCATION OF THE UNIT

Place the equipment on a level and stable surface away from direct sunlight. The intense UV light

can cause discoloration on the plastics. Locate your equipment in an area with cool temperatures

and low humidity. Please leave a clear zone on both sides of the equipment that is at least 24”

(600 mm). This zone must be clear of any obstruction and provide the user a clear exit path from

the machine. Do not place the equipment in any area that will block any vent or air openings.

The equipment should not be located in a garage, covered patio, near water or outdoors.

LEVELING THE EQUIPMENT

The equipment should be level for optimum use. Once you have placed the equipment

where you intend to use it, raise or lower one or both of the adjustable levelers located on

the bottom of the frame. Use 6mm hex key through the access hole (shown below).

A carpenter’s level is recommended.

NOTE: There are only two levelers on the equipment.

WARNING!

Our equipment is heavy, use care and additional help if necessary when

moving. Failure to follow these instructions could result in injury.

POWER

If the equipment is powered by a power supply, the power must be plugged into the power jack, which

is located in the front of the equipment near the stabilizer tube. Some equipment has a power switch,

located next to the power jack. Make sure it is in the ON position. Unplug cord when not in use.

WARNING!

Never operate equipment if it has a damaged cord or plug, if it is not working properly, if it has been

damaged, or immersed in water. Contact Customer Tech Support for examination and repair.

ENGLISH

FREE AREA

0.6 m

(2 ft)

0.6 m

(2 ft)

0.6 m

(2 ft)

TRAINING AREA

12

PROPER USAGE

RECUMBENT: To determine proper seat position, stand to the side of the equipment and adjust the seat by

pulling up on the orange handle. Slide the seat fore and aft and adjust as needed until your knee bends slightly

at the furthest pedal position. To avoid injury, never adjust the seat position when sitting on this equipment.

UPRIGHT: To determine proper seat position, stand to the side of the equipment and adjust the

seat by pulling up on the orange handle. Slide the seat up until the seat is slightly lower than

hip height. Continue to adjust as needed until your knee bends slightly at the furthest pedal

position. To avoid injury, never adjust the seat position when sitting on this equipment.

BRAKE SYSTEM

This exercise bicycle uses a speed-independent braking system. The user is able to adjust

the resistance of the braking system independently of the RPM of the crank axle.

USING THE HEART RATE FUNCTION

The heart rate function on this product is not a medical device. While heart rate grips can provide

a relative estimation of your actual heart rate, they should not be relied on when accurate readings

are necessary. Some people, including those in a cardiac rehab program, may benefit from using an

alternate heart rate monitoring system like a chest or wrist strap. Various factors, including movement

of the user, may affect the accuracy of your heart rate reading. The heart rate reading is intended only

as an exercise aid in determining heart rate trends in general. Please consult your physician.

Place the palm of your hands directly on the grip pulse handlebars. Both hands must grip the bars for

your heart rate to register. It takes 5 consecutive heart beats (15-20 seconds) for your heart rate to register.

When gripping the pulse handlebars, do not grip tightly. Holding the grips tightly may elevate your blood

pressure. Keep a loose, cupping hold. You may experience an erratic readout if consistently holding the grip

pulse handlebars. Make sure to clean the pulse sensors to ensure proper contact can be maintained.

WARNING!

Heart rate monitoring systems may be inaccurate. Over exercising may result in

serious injury or death. If you feel faint, stop exercising immediately.

ENGLISH

13

MAINTENANCE SCHEDULE

ACTION FREQUENCY

Unplug the unit. Clean entire machine using water and a mild soap or

other Matrix approved solution (cleaning agents should be alcohol and

ammonia free).

DAILY

Inspect the power cord. If the power cord is damaged, contact Customer

Tech Support.

DAILY

Make sure the power cord is not underneath the unit or in any other area

where it can become pinched or cut during storage or use.

DAILY

Clean underneath the cycle, following these steps:

• Turn o the cycle.

• Move the cycle to a remote location.

• Wipe or vacuum any dust particles or other objects that may have

accumulated underneath the cycle.

• Return the cycle to its previous position.

WEEKLY

Inspect all assembly bolts and pedals on the machine for proper

tightness.

MONTHLY

Clean any debris o of the seat guide rail. MONTHLY

MAINTENANCE

1. Any and all part removal or replacement must be

performed by a qualiﬁed service technician.

2. DO NOT use any equipment that is damaged and or

has worn or broken parts. Use only replacement parts

supplied by your country’s local MATRIX dealer.

3. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for

any reason. They contain important information. If unreadable

or missing, contact your MATRIX dealer for a replacement.

4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to

smooth operating equipment as well as keeping your liability to a

minimum. Equipment needs to be inspected at regular intervals.

5. Ensure that any person(s) making adjustments or performing maintenance

or repair of any kind is qualiﬁed to do so. MATRIX dealers will provide

service and maintenance training at our corporate facility upon request.

WARNING

To remove power from the unit, the power cord must

be disconnected from the wall outlet.

ENGLISH

PRODUCT SPECIFICATIONS

UPRIGHT RECUMBENT

CONSOLE TOUCH PREMIUM LED LED / GROUP TRAINING LED TOUCH PREMIUM LED LED / GROUP TRAINING LED

Max User Weight 182 kg / 400 lbs 182 kg / 400 lbs

Product Weight 70 kg / 154.3 lbs 68.2 kg / 150.4 lbs 67.5 kg / 148.8 lbs 91 kg / 200.6 lbs 89.2 kg / 196.7 lbs 88.5 kg / 195.1 lbs

Shipping Weight 83 kg / 183 lbs 81.2 kg / 179 lbs 80.5 kg / 177.5 lbs 112 kg / 246.9 lbs 110.2 kg / 242.9 lbs 109.5 kg / 241.4 lbs

Overall Dimensions

(L x W x H)*

122 x 74.4 x 152.1 cm /

48.0” x 29.3” x 59.9”

154.3 x 67.4 x 144.2 cm /

60.7” x 26.5” x 56.8”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX equipment.

Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.

14

󴱵󴐻󲠱󱲈󰨽󵊠

󴑛󰤭󲫷󲂼󱯛󰬚󰞽󴐺󱾞󳀔󴎽󴎘󲺸󴦤󰤏󲺸󲂼󰧵󴠻󴡚󴑛󰲏󰤏󲺸󴊍󴦰

󰻖󱢊󴔀󰡵󱊦󳀔󴫝󰢆

󳱵󰧵󴠻󴡚󲪱󲙥󲓳󱟈󴧛󰣬󱮦󱞂󱶝󱉮󰃩󰮗󰲏󰤏󲺸󴑛󳧿󳛱󱔲󱯆󱰐󴇣

󱺿󱶄󴩸󴼐󱮦󱴘󲒚󳜣󴱇󰻖󴧂󴇜󲐲󲅵󰸜󳜽󰥾

󰤏󲺸󰧵󴠻󴡚󱿒󴑛󰱩󱥕󳐏󳷧󰶘󴧹󳀔󵄛󱓠󰮗󰲏󴛴󳬃󰤏󲺸󰧵󴠻󴡚

󴑛󰲏󳐏󳷧󰢋󰣥󰵿󳪍󲂓󰲎󰣟󰧵󴠻󴡚󰞚󰢋󰣥󲛋󰱥󵂆󰢆󳀔󴇳󲯹

󴑛󵀸󱿒󲙸󱪟󰃩󱯛󳬃󰲏󴎈󳉀󲛋󰱥󵂆󰢆󰃩󰡵󰫝󰵧󰩇󰞝󰵿󱤢󱯛󴣙

󰱥󴞟󲄏󲂂󲅔

󴑛󳓙󱤕󳬃󴞟󲄏󱔜󰫸󵃬󲓲󰟛󱤜󰬝󵁲󴼛󰧵󴠻󴡚

󰮗󰲏󰾧󴏶󰡵󳑩󳑛󱎏󰱲󰤏󲺸󰧵󴠻󴡚

󰮗󰲏󱖗󰢋󰣥󲯹󰹑󱮦󱯛󳬃󱻎󰫵󰢋󰣥󴼛󰵳󳿥󰃩󱯛󳬃󱮦󱯛󳭒󰠶󰞝󰵿󳉀

󴎈󰧵󴠻󴡚󳀔󰩃󰱥󴉭󳣾󱮦󰬆󰡦󰵿󳪍󲂓󳎋󰱥󳀔󵂆󰢆

󰢋󰣥󰿸󲃠󰞐󱽶󱶝󱉮󱮦󵂆󰢆󳉸󱶝󳇄󱶝󰃩󰞐󱤛󰞝󱤧󳠌󳠜󰤏󲺸

󴑛󰤏󲺸󱔲󱯆󱰐󴇣󱺿󱶄󴩸󴼐󱮦󱴘󲒚󳜣󴱇󰻖󱵠󰤫󳀔󲂏󱵫󵂆󰢆

󰤏󲺸󲖳󵂷󱀄󵂷󲺲󰹑󱿒󰃩󱮦󲼆󲖷󲖳󰵧󴿠󱩕󲙑󰞛󰃩󴑛󰲏󱹝󰣬󲂼

󰿸󲃠

󳱵󰧵󴠻󴡚󱯐󱂸󰣝󳣾󴿔󴥡󲂙󰫢󳑵󰃩󱥕󵆘󴧂󴇜󱁄󱕖󳀔󳁳󳃳

󲂼󰿸󲃠󰞝󴧹󲺸󱽌󵑤󳪍󳅵󴍊󱮦󳙎󳋮󲏯󳪍󰞝󰤃󱮦󲒰󳣊󳜣󵏧󰵚󳅵󴓨

󳀔󰡊󱉻󰃸󱌒󲓂󰤏󲺸󰃩󱥕󵆘󱂸󰡦󰡊󳁳󳃳󰞛󴧂󴇜󰃩󰞤󵆘󲻁󰵿󴘰󴘼󰬆

󰡊󴠻󱔙󰫸󳦕󱲗󱖞󰿸󲃠󲺸󴦤󰵚󰤏󲺸󱽉󱢟

󳉊󱔪󱯐󲂙󴑏󱼄󲈏󱠷󲊕󰸜󰯝󱤜󱰚󱯛󳀖󲯲󲯲󱂊󱔪󰃩󴧛󰱥󱿒󳀔󲛋

󰱥󳕔󱂝󰫷󰞝󰵿󲂙󵀬󳊩󲯹

󴲿󴐴󴧛󰱥󱽉󱢟󰸜󴧛󰱥󴧞󴭟󰵿󳪍󲂓󱖞󳮄󱁄󴭝󰵧󰩇󱮦󲔋󰠱󳱵󱨸󱪯

󴍊󰶔󳎾󰞝󰶜󳀔󲽌󲽫󰃩󰲕󱱼󳪈󲽫󰿑󱥓󲀘󳂹󱮦󰸌󰷈󱂀󵁳󳓙󰃩

󱭙󳑛󰴃󰧬󲓲󴧛󰱥󰞶󴑛󱻩󴬻󱞻󲓴󲽗󲱐󰟛󱤜󰃩󱯝󰵿󳠌󳠜󰤏󲺸

󴑛󰲏󱂸󲂼󰿸󲃠󰞚󴞃󴠝

󴧛󰣬󰞽󳀔󰿸󲃠󰩕󴿠󰼾󰡊󰤏󲺸

󵑤󴭝󴜕󴧞󱲑󲂙󱯛󰬚󴌟󲇌󴩸󰮖󴌟󱔪󳀔󰡊󱉻󰃩󰞝󱤧󰤏󲺸󲂼󴎽󰨩

󲂺󴨅󱔘󴌟󱔪󱯐󱖞󳮄󳀔󱶝󱕃󰃩󳀖󰞝󱂸󰥭󱂊󳕔󱂝󰫷

󱖗󵂋󲠠󳝪󱻎󱂸󴧰󵁲󲭁󲠠󳀔󱃀󱽉󴑛󰲏󰤏󲺸󲂼󰿸󲃠󵀸󴿔󳀔󵂋󳝪󱶼

󴧛󲂼󰿸󲃠󰃩󰟯󰞝󰵿󱖗󵂋󳝪󲼆󱮠󱰚󱯛

󴑛󰲏󰤏󲺸󴊍󴦰󰻖󱢊󴔀󰡵󱊦󳀔󰬆󰡦󴫝󰢆󰤏󲺸󰞝󲼆󴫝󰢆󰵿󳪍󲂓

󱖞󳮄󰡊󴠻󰩇󱕃

󴑛󰩕󱲙󲫷󴎽󰨩󱲗󰳧󰵚󱲑󲂙󰡊󱯛󰬚󰞽󳀔󴐺󱾞󰤏󲺸󲂼󴎽󰨩

󳜽󰥾󱮦󳎋󰱥󲂼󰿸󲃠󰯝󰃩󴑛󰫘󱱤󰞛󱯐󲂙󵂋󲠠󱴵󳝪󲞕󲣤

󱿒󰃩󴑛󰤏󲺸󳨵󳀒󰵚󱤾󲥥󳀔󱞓󱹶󱱽󰿸󲃠󴇸󵃲󰃩󰮗󰲏󰤏󲺸󲡆

󰰡󴑛󰵓󴽁󰥭󵊚󳑰󳕐

󲪱󴑦󰢋󰣥󱩕󲙑󰞛󰃩󴪍󰞝󱭙󴐂󴔣󱖅󲯹󱮦󲔂󰡵󰞛󰫢󳑵󰃩󱴵󴥡󲂼

󰿸󲃠󰷸󱂝󰫼󱗊󳲁󱗊󰫷

󱁄󳌑󲂺󲢏󲔂󳀔󰫢󳑵󰤏󲺸󲂼󰿸󲃠

󱠄󲢏󲔂󳀔󰫢󳑵󰃩󱥕󵆘󲂙󱮠󰡊󴿺󰶜󳁳󳃳󱯝󳪍󰤏󲺸󲂼󰿸󲃠

󱌒󲂼󴎽󰨩󳀔󵂋󲠠󳝪󱮦󱵢󵆽󱶝󱉮󱝵󰣬󰞝󲓳󱟈󱴙󳷍󱮦󱶝󱉮

󱮦󳦕󲜈󰫵󲗄󰞽󰃩󰮗󰲏󱹝󰣬󴑛󱖗󴎽󰨩󴦑󱁮󱔲󱯆󲂝󰱩󰞽󱥓󴧂󴇜

󲐲󰥾

󲠱󱲈

󰬭󳀬󲊎󱈆󲊲󰷲󴖃󰳯󴖥󴔜󴱖󱦫󰦋󰬭󳀬󰷲󴖃󷣤󴘷󰬭󳀬󱶾󰴰󰦋

󲂼󰿸󲃠󰱩󱥕󰵺󳪍󱂸󰵿󱴷󰯆󲠻󱠶󳀔󱔴󰫷󰤏󲺸󱌒󲄬󱨸󳀔󴝡󲓵󲏯󲂎󲁄󵃂󱂸󰣞󲠻󱮦󵑨󱠶󲣾󲥥󳀔󲹀󱈓󰞛󰃩󱣇󲩘󱢊󴔀󱨸󱂸󰮭󲒱󰤏󲺸󰯝󰫘󴔣󴝡󲓵󲏯󲀦󲏯󳮃󳒶󰶘󱔴󲠻

󴘝󰿪

󲯦󵃫󰫾󲳷󲳾󰱠󰦊󴒲󵆗󱶋󰽸󰱠󳆁󵍂󵅈󱶋󰩫󴥡󰱠󱜽

󳱵󴌑󰞽󱽇󵂋󲠠󰃩󴑛󱖗󱯐󲂙󱴷󰯆󰰯󳪍󰮗󱵫󰯀󴽬󴼙󰣝󳣾󰃩󲫆󱤜󱱤

󰞛󵂋󲠠󱵢󵆽

󴿴󵃮󳜣󱔲󲂝󱰐󴇣󰡊󰹱󱲗󳋊󰃩󴑛󰲏󱖗󰪐󴇸󳀔󴔇󳹛󱱖󰞛󰩕󰠴󲻁󳜣

󱴘󲒚󳀔󳜽󰥾󱰐󱞻󴧂󴇜󳜽󰥾

󱥓󲴗󳁳󲞼󳚋󳜁󰵿󳪍󰞝󲠦󳉊

󴖃󱔷󰮊󱛥󴫈󰩌󷝄󲅶󲉚

󰤏󲺸󰧵󴠻󴡚󱿒󰃩󴑛󰱩󱥕󴨅󴇜󱆊󲂼󲙸󱪟󰠛󵆕󰃩󰲕󱱼󰞛󰮧󴌑󵡮󰃷󰤏󲺸󲂼󰿸󲃠󰯝󴑛󴽁󴔐󱯐󲂙󰤏󲺸󴐺󱾞

󱲑󲂙󰡊󱭙󴘰󴘼󳉊󰥭󱞂󰫕󰮖󰷚󳅵󲂼󴝡󲓵󲏯󰤏󲺸󳦕󱯐󲂙󴓶󰷚󳮗󲙸󱪟󰠛󵆕

󲂼󰿸󲃠󰩕󰤫󱔴󰫷󰤏󲺸󲂼󴎣󳞄󰿸󲃠󱗼󳚋󰮧󲺲󰹑󰃩󱖘󲺸󱽌󰧵󴠻󱯏󳓙󳀔󰻖󰱩󲹀󱈓

󰼒󵅈

󲯦󵃫󰫾󴒲󵆗󵍂󵅈

󰤏󲺸󱔜󲻲󱤜󲞕󲣤󰯝󴧂󴇜󰥭󵊚󰡵󰵚󱔙󴉭󱮦󱱖󰴈󵂆󰢆󱿒󰃩󴑛󰱩󱥕󱤮󵂋󲠠󱵢󱠷󱱤󰞛󲂼󰿸󲃠󳀔󵂋󲠠󱵢󵆽

󳟑󵑤󰞽󱼗

15

󱞐󳀬󵆗󴢥󱀬󵆗󲝱󴝾󴓄

󱖘󲺸󵂋󴝿󱾿󱲗󱥕󵆘󰤏󲺸󱖘󲺸󱵢󱠷󰃩󰞝󰵿󳮗󰬆󰡦󰢋󰣥󵂋󰿸󰬁󲺸󵂋󴝿󲂐󳖱󰼾󳀔󲐲󲅵󱽉󱢟󱾿󱰎󰯀󰟋

󱽇󴝿󰿸󳕁󰃩󲫆󱤜󰞐󲒱󴽬󴼙󰞐󰦛󱽇󴝿󰿸󴽬󴼙󱽇󴝿󰿸󱤜󰃩󱭙󴐂󰵺󲂙󲐲󲅵󰞽󳀔󰿸󲃠󱋁󰵋󵂋󰰫󴧂󴇜󴦩󵆕

󲞼󴏶󱿒󰃩󵂋󲭘󴘹󴙳󲏯󵈸󱯗󵆃󵆏󳚋󳜁󱮦󱯐󲂙󰬆󰡦󲯹󰹑󳀔󵂋󰰫󴪍󰞝󱭙󴐂󰮊󲶎󰞽󱽇󱩕󱣲

󵃮󴦄󴝿󳛥󳝳󰞝󱟆󵂋󱴵󱃀󱾿󱲗󲕟󰦛󵂋󴝿󴪍󴌑󲂙󰞐󲈭󱖝󱊦󳀔󲳸󳑛󳛥󳝳󱴵󱃀󳝪󰃩󰞶󰞤󳪍󱲙󲫷󰶘󲇌󳀔󱴵

󱃀󱽉󱢟󱽇󵂋󰞝󳪍󰮹󲺸󴞃󱴵󱽉󱢟󱖗󰬆󰞽󰞐󰦛󵂋󴝿󳀔󰼾󰞐󰞝󱟆󵂋󱴵󱃀󳝪󱴵󰯀󰞛󰞐󰦛󵂋󴝿

󵆗󲝱󴐻󲞐

󲩊󰠖󱨸󳀔󱔙󰫸󰞶󳉊󰥭󳯿󱌍󳀔󴉭󳣾󱻘󳪍󰃩󲓴󵂋󴝿󳀔󱴵󱃀󱥕󵆘󲩊󵃮󲹀󴝿󰃥󵀤󵁲󰃦󴑛󰵓󴽁󲈭󱼗󳒼

󲈭󰸜󲈭󱖝󱯐󱵠󰤫󳀔󲎩󲠦󵂋󲠠󳝪󴧂󴇜󰢋󰣥󱻉󰱥󰃩󳀖󰵿󰡴󲂼󲺲󰹑󳀔󱯐󲂙󰥭󱂊󱋁󱻘

󱴱󲺸󰸜󰪐󴇸󳛔󳀔󴎽󰨩󰵿󳭺󰤫󵂋󰃩󲪱󵂐󱊦󱴵󵂋󲠠󰟯󰵿󴧛󰣬󰞝󰤏󲺸󱊦󱴵󵂋󲠠

󱿒󰃩󰪐󴇸󳛔󳀔󰻯󰱥󱿒󴼣󰵿󳪍󲂓󱢆󴨂󱊦󱴵󵂋󴌦󳮗󰬆󰡦󰪐󴇸󳛔󴫝󰢆󵂐󴌑󱊦󱴵󵂋󲠠󱊦󱴵󵂋󲠠󰵿󳉊󰥭󱍛

󳛒󰶡󰪐󴇸󳛔󱵠󰤫󵂋󲠠󰃩󰤏󲺸󱊦󱴵󴫝󰢆󱿒󵂐󴌑󱊦󱴵󵂋󲠠

󱖝󱽌󱟆󱼄󰶘󱄛󵂋󴌦󳀔󴎽󰨩󰃩󵂋󴌦󵂋󲠠󴌑󲗒󰲕󰶻󱽌󴎽󰨩󰞽󵂐󰤏󲺸󰬆󰞽󰞐󳑿󲩊󱄛󱉣󰶘

󱴵󵆽󳀔󱄛󱁫󱗟󳻍󰶜󴢈󵂋󳠬󳝪󴦳󱴵󱥓󳩊󴎣󳞄󰿸󲃠󰸜󴌦󴎚󰤖󲠠󱊦󱴵󱼈󰣝󵂋󴌦󲘢󲂙󰬆󰡦󵂋󲠠󵂐󲗒

󱈆󲊲

󰿸󲃠󵂐󴌑󰤏󲺸󰡵󰵚󳀔󱖘󲺸󵂋

󴝿󰃩󰡵󰵚󵃮󴦄󴝿󳛥󳝳󰞝󱟆󵂋󱴵󱃀󵂋󲠠󲓴󱵢󱠷󱭙󲩊

󰃩󰞶󰬇󲂙󳮗󱵢󵆽󳂈󰶜󳀔󳛔󱫛󴎽󱔪󲂼󲺲󰹑󰞝󱭙󰤏󲺸󴔚󱉣󰿸

󴦩󰠫󰧵󴠻󴡚󰵿󰡵󳵚󴵘󱣲󱢟󴦳󱴵󱂸󰞐󴜇󰃩󲕟󲈭󱖘󲺸󵂋󴝿󲂐󱊪

󰦛󴎽󰨩󳵚󴵘󳝪󴧹󴫝󰿸󰼾󲳸󰮊󰺾

󵆗󲧎󵆜󲞐

󱼗󱋋󷝄󲅶

󲂼󰿸󲃠󵆘󱴵󱃀󳱵󲂼󰿸󲃠󳀌󲺯󱻕󵀬󱮦󱶝󱉮󰃩󱴵󱃀󰵿󱵠󰤫󴿋󰰫󲂐󱖟󳀔󴝿󱤡󰤫󵂋󲛑󴦪󴧞󰃩󰡵󴿝󰣞󴎈󵂋󵈸󵀺󲂼󰿸

󲃠󴫝󰨩󰞐󲈭󴿔󰿸󲃠󱴵󱃀󱖞󵑤󳀔󵂋󳝪󰃩󴨔󲂙󰞐󰦛󱴵󱃀󱵢󵆽󴑛󱖗󱵢󵆽󱵢󰫵󳒶󰶘󲼆󱃀󱔙󴉭󰸜󱴵󱃀󲙥󴌟󳀔󱵢󱠷󰞽

󳱵󰤏󲺸󳦕󲂺󴨅󱤺󱴵󱃀󴐺󱾞󰃩󲂙󴿠󰥭󱂊󰞐󱤛󱋁󱻘

󰴜󰪇󵆗󲝱󴝾󴓄

󴿴󱖘󲺸󵂋󴝿󵂐󲗒󱊦󰃩󰟯󵆘󰡵󲓳󳉊󳀔󲎩󲠦󳝪󴦳󱴵󱽇󴝿󰿸󰸜󲕟󰦛󱖗󱵢󰞚󲂐󱊪󰿸󲃠󳀔󱵢󱠷󳱵󱽇󴝿󰿸󳮗󲕟󰦛󱵢󱠷

󰟛󴼣󳀔󴝭󵁲󳓙󱽌󱮦󱖟󱽌󰷞󰫼󱗊󰃩󱭙󰤏󲺸󳿯󲎩󲠦󳝪󳱵󱽇󴝿󰿸󰸜󱵢󱠷󰟛󴼣󳀔󴝭󵁲󱊷󱽌󰷞

󰫼󱗊󰃩󰯗󱭙󰤏󲺸󳿯󲎩󲠦󳝪

󳚯󳯙󳇽󵆗󲕹󱪍

󱯐󲂙󰿸󲃠󳀖󴎽󱔪󲩊󴔣󰿸󲃠󱂸󴼢󳣾󴧤󱲗󱔪󱿒󴼣󱤜󴧂󰫵󳕐󳪍󳂑󵂋󲎱󱢟󲂼󰿸󲃠󴧂󰫵󳂑󵂋󲎱󱢟󱤜󰃩󱌒󴌑󴭝󱽀󰻯󰱥󰃩

󰵿󳪍󵂐󴌑󴢓󴼇󳀔󱿒󴼣󱂸󳔱󲶖󰹱󲎱󱢟󱮦󱝵󳎛󲎱󱢟󰞛󳀖󰵿󰻯󲺸󱮦󰧬󲺸󴦩󵆕󳕐󳪍󰰯󳪍

󱒩󱼗󲃣󰫽󵆗󴑐

󱊦󱴵󱼈󰣝󵂋󴌦󵂐󴌑󵇝󱊦󳀔󵂋󲠠󰃩󱥕󵆘󰤏󲺸󱊦󱴵󵂋󲠠󴌦󴎚󰤖󲠠󰸜󲕟󰦛󴿔󰰰󱼈󰣝󵂋󴌦󴎽󰨩󰟛󴼣󵂐󴌑󴦳󱴵󰞐󲈭󱟆

󱄛󱉣󳞾󴫝󰢆󳀔󰶜󴢈󵂋󳠬

󲠞󴑉󰱮󵃮󳩯󱊦

󲂼󰿸󲃠󱞂󳜣󴧞󲞼󴏶󰃩󳒶󰶘󴌟󰯗󳒼󴩸󰮖󱖝󵇮󱼈󰣝󴎽󰨩󰟛󴿠󰯆󴦩󰠫󴿠󰯆󱽸󱂸󱵠󰤫󰶘󲶖󰥭󴔇󰃩󴿂󲓲󰣟󱔕󱔙󴉭

󰟛󲂙󱕃󱠂󱺎󲂼󰿸󲃠󲂓󲺲󲺯󰤏󲺸󰞶󳀌󱖔󲪱󳝪󵂋󵇋󲴗󳪍󴭟󳱵󲂺󱲙󲫷󴐺󱾞󴧂󴇜󱔙󴉭󰸜󰤏󲺸󰃩󰵿󳪍󲂓󱖝󲪱󳝪󵂋󴦪󴎚󲺲

󲺯󲂙󱕃󱠂󱺎󰞝󴧞󰃩󲪱󲙥󰥭󴓙󱂸󲰉󱔪󱔙󴉭󱿒󰞝󲂓󳀌󲺯󱠂󱺎󰦨󲂼󰿸󲃠󳉊󱕶󱖝󲪱󳝪󵂋󱮦󵂋󴌦󱴵󱻆󲺲󲺯󲂙󱕃󱠂󱺎󰃥󰵿󴽬

󴼙󰸜󱯣󴼛󰿸󲃠󳉊󱔪󰃦󰃩󱢊󴔀󲺸󱯆󰾧󴏶󰡵󰞛󰞐󳎾󱮦󱊪󳎾󱽉󲙥󴿋󱽇󱠂󱺎󰃷

󴭝󱽀󴑏󱼄󱮦󱺊󱻎󱴵󱻆󱊹󳝪

󱱙󴼛󰿸󲃠󰸜󱴵󱻆󰿸󰟛󴼣󳀔󴝭󵁲

󱖗󰿸󲃠󴦳󱴵󰯀󰞝󰶜󱽌󱴵󱻆󰿸󱯐󴦳󱴵󵂋󴝿󰟛󵂋󲠠󱵢󱠷

󴑛󴑾󴏲󳜣󴱇󰻖󱮦󳜣󵏧󴗠󱕜󰟛󲪱󳝪󵂋󰃬󵂋󴌦󱰐󴇣󰡊󰹱󰡵󲴂󱤧󰳤󰰹

󴣋󱖔󲁄󵃂󳨂󱾞󰃷

 󲓴󳀌󱖔󰿸󰞝󱤧󳮗󰢋󰣥󰬆󰡦󱊹󳝪󱮦󳀌󱖔󰿸󱻎󱂸󰶜󰞐󰣝󳣾󱮦󰶜󱿒󱹝󰣬

 󲂼󰿸󲃠󳒶󰶘󴣋󱖔󲁄󵃂󴿠󰯆󰟛󰞝󰵧󱴷󰯆󲹀󱈓󴌟󱔪󱔙󴉭󳮗󱹝󰣬󲂼󰿸󲃠󱿒󰃩󱻳󲭁󰿸󳮗󴠻󵑤󰟛󴼣󳮃󱖡󱭙󴝭󵁲

󰫼󰮖

󵇿󳋊󰲧󳤞󰸜󲓠󲛂󵂋󲠠󳝪󱵢

󵆽󱵢󵆽󵇮󱄛󱁰󱂛󱕆󱃀󰳐

󳦜󲼀

󱽄󵋈

󰧁󴬗󳀬

󲚣󱪍󱽄󵋈󲚣󲡹

󳟑󵑤󰞽󱼗

16

󳘞󵊜 󲄇󳲿󱪍󰰎󴥡󴥿

󳘞󵊜 󳇱󳖾󱪍󰰎󴥡󴥿

󱸹󵀪󰺧󴎙

󱂸󵆠󱔪󴌑󰤏󲺸󲂼󰿸󲃠󳀔󱃀󱽉󱱖󱖑󴑛󱖗󳚩󳕁󱻎󱂸󱠃󱃶󳀔󴇸󵃲󰞚󱢊󴔀󱨸󱂸󱃀󲄏󰞚󴱺󰞐

󱗴󴿂󴔇󱈚󰮗󰲏󱂸󰲕󴉭󳕁󰨄󱻎󳀔󱩕󲙑󰞛󱯣󴼛󰲕󴉭󳕁

󴱵󴐻󲠱󱲈󰨽󵊠

󴧂󴇜󲕟󰦛󳛔󴉭󲓵󵏯󱿒󰃩󴑛󳉊󴐝󱯐󲂙󴅊󱟍󰸜󴅊󳜂󱞂󱔪󰣝󰞤󴩸󰮖󴴦󳝚

󲩊󱽉󰥏󱨸󳛔󴉭󰸜󰤏󲺸󰃩󴩸󰮖󵂆󰢆󱞂󰠛󰫘󲣴󲡡󴧞󴑛󰲏󱹶󴿴󲣴󲡡󲙉󱌒󲄬󳛔󴉭󲂙󱂀󵁳󰃩

󱢊󴔀󱨸󱇧󱱉󱖡󴭟󴭭󴡚󲙉

󴘝󰿪

󳛔󴉭󴧞󳎛󰞽󲂙󱠎󰦛󴩸󰢍󵆘󲰉󰮵󲙸󱪟󴑛󰱩󱥕󲓳󳉊󴨅󱤺󳛔󴉭󴐺󱾞󰃩󰡵󳉊󴐝󱯐󲂙󵂆󰢆󱃗󱔜

󰫸󱂊󱔪󳱵󲂺󳉊󱕶󴨅󲫷󳛔󴉭󴐺󱾞󰵿󳪍󲂓󱖞󳮄󲂼󰿸󲃠󳀔󵂆󰢆󲂺󴴦󳝚󳦜󵒖󳪻󰃩󰞶󳀌󰮊󱺎󰡊

󳀔󰿺󵆃󲩊󴨏󰫝󱶝󱉮󰿸󲃠󰃩󴑛󰱩󱥕󴐃󴽁󳛔󴉭󴐺󱾞󰞶󰠘󰡵󰥾󲓳

󵆜󴐻󰻶󰹍󱅭

󱌒󲄬󲂙󰢋󰣥󲼡󰻟󱮦󲂙󳣊󱖡󵂆󰢆󰃩󴑛󳧿󳛱󱔲󱯆󱰐󴇣󱺿󱶄󴩸󴼐󳧿󳛱󴙗󴎚󰣝󱽌󴙗󴎚󰳱󰞚

󳠰󴎙

󳟑󵑤󰞽󱼗

17

D

C

󱶳 󵆜󱥥 󰴝

F 󰫷󰫽󴍢󱰃󱯛

F 󰫷󰫽󴍢󱰃󱯛

F 󱯑󱠃󱰃󱯛

F 󰳑󱓧󴅊󳜂󴜇󱓠

󵅆 󵃢 󵆒 󰪧

F 󰦛󰟋󴡚󲅆

F 󰦛󱤜󴙌󱃀󲈏

F 󰦛󰯝󴙌󱃀󲈏

F 󰦛󱤜󴡚󲅆󱰚󱯛

F 󰦛󱤜󴡚󲅆󴔇󳹛

F 󲇉󰪐󴇸󱺿󱸠󲈏

F 󰦛󰪐󴇸󱰚󱯛

F 󰦛󱰚󱯛󴔇󳹛

F 󰦛󲊕󲅆

F 󰦛󲗄󱊊󲅆

F 󰦛󱠷󲊕󱠥󱠷

F 󰦛󱠷󲊕󵃰󳩜

F 󱋧󰠤󴭡󱝵󰬇󰲕

F 󲈭󵂋󲠠󳝪

󰪐󴇸󰵶󰺾

A

B

1

󰩅󴱹 󲃣󴱷

A

B

󴅊󳜂

󱣘󳖷󱈚󱂘

8

2

󰩅󴱹 󲃣󴱷

C

D

󴅊󳜂

2

󲄇󳲿󱪍󰰎󴥡󴥿󴯸󰪧

󳟑󵑤󰞽󱼗

18

O

N

M

L

H

I

E

F

G

3

󰩅󴱹 󲃣󴱷

E

F

G

󴅊󳜂

󵣢󱣲󱈚󱂘

󴅊󳜂󵆠󴉭

4

󰩅󴱹 󲃣󴱷

H

I

󴅊󳜂

2

4

5

󰩅󴱹 󲃣󴱷

J

K

󴅊󳜂

󱣘󳖷󱈚󱂘

4

6

󰩅󴱹 󲃣󴱷

L

M

N

O

󴅊󳜂

󱣘󳖷󱈚󱂘

󱢷󱣲󱈚󱂘

󴅊󳜂

4

3

J

K

󳟑󵑤󰞽󱼗

19

󳠰󴎙󱜘󱶅

P

Q

R

7

󰩅󴱹 󲃣󴱷

P

Q

R

󴅊󳜂

󴅊󳜂󵆠󴉭

󴅊󳜂

2

4

2

󱶳 󵆜󱥥 󰴝

F 󰫷󰫽󴍢󱰃󱯛

F 󰫷󰫽󴍢󱰃󱯛

F 󱯑󱠃󱰃󱯛

F 󰳑󱓧󴅊󳜂󴜇󱓠

󵅆 󵃢 󵆒 󰪧

F 󰦛󰟋󴡚󲅆

F 󰦛󱤜󴙌󱃀󲈏

F 󰦛󰯝󴙌󱃀󲈏

F 󰦛󱤜󴡚󲅆󱰚󱯛

F 󰦛󱤜󴡚󲅆󴔇󳹛

F 󲇉󰪐󴇸󱺿󱸠󲈏

F 󰦛󲗄󱊊󲅆

F 󰦛󱠷󲊕

F 󳛔󱰆󱯛󱰚󱯛

F 󰦛󰯝󰨄󴔇󳹛󵆠󴉭

F 󰦛󱤜󴔇󳹛󵆠󴉭

F 󱋧󰠤󴭡󱝵󰬇󰲕

F 󲈭󵂋󲠠󳝪

󰪐󴇸󰵶󰺾

󳇱󳖾󱪍󰰎󴥡󴥿󴯸󰪧

1

2

3

4

5

6

7

󴦪󴎚

󱺄󰫕󵂋󲠠󳝪

󵂋󴌦󵂋󲠠

󰪐󴇸󳛔󴦳󱴵󳝪

󰟩󱊺󳝂󴝿

󰶜󴢈󵂋󳠬

󱴵󱃀󳝪

1

7

6

5

4

3

2

󳟑󵑤󰞽󱼗

20

E

F

H

G

I

C

D

A

B

1

󰩅󴱹 󲃣󴱷

A

B

󴅊󳜂

󱠃󱈚󱂘

8

2

󰩅󴱹 󲃣󴱷

C

D

󴅊󳜂

2

3

󰩅󴱹 󲃣󴱷

E

F

G

H

I

󴅊󳜂

󵣢󱣲󱈚󱂘

󴅊󳜂󵆠󴉭

󴅊󳜂

4

6

2

4

󰩅󴱹 󲃣󴱷

J

󴅊󳜂

4

J

󳟑󵑤󰞽󱼗

ページが読み込まれています...

Matrix RB209 取扱説明書

このマニュアルも適しています

Matrix RB209 取扱説明書

関連論文

その他のドキュメント