Oriental motor EMU1238 取扱説明書

ブランド: Oriental motor

モデル: EMU1238

タイプ: 取扱説明書

このマニュアルも適しています



HF-3154

規格・CEマーキング



EMU1238M

［図記号の説明］



1 2



•

EMU



［フィンガーカードを取り付ける場合］



重要

1700 ± 255 r/min



取付条件

風の方向、羽根の回転方向

風の向き

羽根の

回転方向

入力端子

ねじサイズ： M4

締付トルク： 0.6 N･m

フィンガー

ガード

電源

黄

黒アラーム

出力

AC100-240 V

電源の接続

アラームの接続と仕様

［接続図］

［アラーム仕様］



R：制限抵抗

黄

黒0 V

お客様の回路ファン

DC30 V以下

10 mA

以下

電源コード

アラーム用コネクタ

入力端子

EMU1238M-□



T-EMU1238M-□-G

Thank you for purchasing an Oriental Motor product.

This Operating Manual describes product handling procedures and safety precautions.

• Please read it thoroughly to ensure safe operation.

• Always keep the manual where it is readily available.

Only qualified and educated personnel should work with the product.

The product described in this manual has been designed and manufactured to be

incorporated in general industrial equipment. Do not use for any other purpose.

Oriental Motor Co., Ltd. is not responsible for any damage caused through failure to

observe this warning.

HF-3154

Safety precautions

Installation Connection

Overheat protection for locked condition

Checking the product

Standards and CE Marking

• Do not use the fan beyond the specifications. Doing so may result in electric

shock, injury or damage to equipment.

• Keep your fingers and objects out of the openings in the fan. Failure to do so

may result in injury.

• Do not touch the fan motor while operating or immediately after stopping.

The surface of the fan motor is hot and may cause a skin burn(s).

• Do not lift the fan by holding the rotating part (blades) of the fan or power

supply cable. Doing so may result in injury.

• Keep the area around the fan free of combustible materials. Failure to do so

may result in fire or a skin burn(s).

• Do not leave anything around the fan that would obstruct ventilation.

Doing so may result in damage to equipment.

• Do not touch the rotating part (blades) while operating. Doing so may result

in injury. The use of the finger guard is recommended to ensure protection.

• Only qualified and educated personnel should be allowed to perform

installation, connection, operation and inspection/troubleshooting of the

product. Handling by unqualified and uneducated personnel may result in fire,

electric shock or injury.

• Shut off the power to the fan in the event the overheat protection circuit is

activated. Otherwise, the fan will start unexpectedly when released from the

locked condition, causing bodily injury or equipment damage.

• Keep the input-power voltage within the specified range. Failure to do so

may result in fire or electric shock.

• Connect the cables securely according to the wiring diagram. Failure to do

so may result in fire or electric shock.

• Turn off the power in the event of a power failure. Otherwise, the fan will

suddenly start when the power is restored, and this may cause injury or

damage to equipment.

Handling the product without observing the instructions that

accompany a “Warning” symbol may result in serious injury

or death.

• Do not use the product in explosive or corrosive environments, in the

presence of flammable gases, locations subjected to splashing water, or near

combustibles. Doing so may result in fire, electric shock or injury.

• Do not transport, install, connect or inspect the product while the power is

supplied. Always turn the power off before carrying out these operations.

Failure to do so may result in electric shock or injury.

• Do not forcibly bend, pull or pinch the cable. Doing so may result in fire or

electric shock.

• Do not disassemble or modify the fan. This may cause electric shock or injury.

Refer all such internal inspections and repairs to the branch or sales office from

which you purchased the product.

The precautions described below are intended to prevent danger or injury to

the user and other personnel through safe, correct use of the product.

Use the product only after carefully reading and fully understanding these

instructions.

Verify that the items listed below are included. Report any missing or damaged

items to the branch or sales office from which you purchased the product.

Verify the model number of the purchased product against the number shown

on the package label. The fan model name EMU1238M is listed on the

nameplate of the fan.

Description

of graphic

symbols

: Indicates "prohibited" actions that must not be performed.

: Indicates "compulsory" actions that must be performed.

Handling the product without observing the instructions that

accompany a “Caution” symbol may result in injury or

property damage.

• Immediately when trouble has occurred, stop operation and turn off the power

supply. Failure to do so may result in fire, electric shock or injury.

• Install the fan inside equipment for sure. Failure to do so may result in injury

or damage to equipment.

• The surface temperature of fan motor may exceed 70 °C (158 °F)

even under normal operating conditions. If the operator is

allowed to approach the fan that is operating, attach a warning

label as shown in the figure in a conspicuous position.

Failure to do so may result in a skin burn(s). Warning label

• To dispose of the fan, disassemble it into parts and components as much as

possible and dispose of individual parts/components as industrial waste.

For products that the power supply cable is supplied with, enter 1 or 2

[1 m or 2 m (3.3 ft. or 6.6 ft.) ] representing the length of the power supply cable

in the box () within the model name.

A fan, which the power supply cable or the cable for alarm is not supplied with,

can also be purchased.

This product is recognized by UL.

This product is affixed the CE Marking under the Low Voltage Directive and

EMC Directive.

• Low Voltage Directive

Applicable standards EN 60950-1

This product is certified by TÜV Rheinland under the EN 60950-1.

• EMC Directive

Applicable standards EMI : EN 61000-6-3, EN 61000-3-2, EN 61000-3-3

EMS : EN 61000-6-2

This product is affixed with the PSE mark under the Electrical

Appliance and Material Safety Law (Air blowers).

Seller and user shall be noticed that this equipment is suitable

for electromagnetic equipments for office work (Class A) and

it can be used outside home.

The products do not contain the substances exceeding the restriction values

of RoHS Directive (2011/65/EU).

OPERATING MANUAL

EMU Series

AC Power Supply Input

Low Power Consumption Axial Flow Fans

Low-Speed Alarm type

Applicable standards : UL 507, CSA C22.2 No.113

Certification body : UL File No. : E58377

When installing the finger guard

• Inside an enclosure that is installed indoors (provide vent holes)

• Operating ambient temperature –20 to +75 °C (–4 to +167 °F) (non-freezing)

• Operating ambient humidity 20 to 85% (non-condensing)

• Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas)

or liquid

• Area not exposed to direct sun

• Area free of excessive amount of dust, iron particles or the like

• Area not subject to splashing water (rain, water droplets), oil (oil droplets) or

other liquids

• Area not subject to continuous vibration or excessive shocks

Install the product in the following location that provides easy access for

inspection.

• Area free of radioactive materials, magnetic fields or vacuum

• Area free of excessive electromagnetic noise (from welders, power machinery,

etc.).

When using near a switching circuit or high-frequency power supply,

the induced current may flow inside the fan due to electromagnetic noise

(conductive noise, radiative noise). If the induced current flows, the electric

corrosion is caused in the bearings of the fan. As a result, it may generate

the noise or shorten the service life of the products. Use the fan in the

environment that the electromagnetic noise does not cause.

For the air flow and the direction of blade rotation, see the arrow indicated on

the side of the fan frame.

• Install the fan to an appropriate flat metal plate having excellent vibration

resistance. Connect to the power supply using the supplied power supply cable.

Securely plug the power supply cable into the input terminals.

Note

In the case of fans with the low-speed alarm, the alarm signal is output when

the speed of the fan falls below 1700 ± 255 r/min.

Output format : Open-collector

Normal L level

Abnormal H level

Output status :

This fan is equipped with a built-in overheat protection circuit. Since this circuit

automatically controls the current flow to the windings when a locked condition

is detected, it prevents the fan from burning out. The fan resumes operation

automatically as soon as it is released from the locked condition. Turn off the

power in the event of inspections.

• Drill mounting holes in equipment, and secure the fan using screws.

Mounting screws are supplied with the fan kit products.

Installation conditions

CE Marking

UL standard and CSA standard

Air flow, direction of blade rotation

Air flow

Direction of

blade rotation

Input terminals

Screw size : M4

Tightening torque : 0.6 N·m (85 oz-in)

Finger guard

Power supply Yellow

Black Alarm output

100-240 VAC

Connection of the power supply

Specification and connection of the alarm

Connection diagram

Alarm specification

• Connect a current-limiting resistor R according to the power supply

voltage if the current flowing through the output signal exceeds 10 mA.

• The alarm circuit is equipped with an internal starting-delay function.

The alarm function becomes effective within 10 seconds after the fan

starts.

R: Limiting resistor

Yellow

Black 0 V

User's circuitFan

30 VDC or less

10 mA

or less

Power supply cable

Connector for alarm

Input terminals

Electrical Appliance and Material Safety Law

Republic of Korea, Radio Waves Act.

Hazardous substances

Warning

Caution

• Unauthorized reproduction or copying of all or part of this Operating Manual is

prohibited.

• Characteristics, specifications and dimensions are subject to change without notice.

• and are registered trademarks or trademarks of Oriental Motor

Co., Ltd., in Japan and other countries.

• Please contact your nearest Oriental Motor office for further information.

Technical Support Tel:(800)468-3982

8:30 A.M. to 5:00 P.M., P.S.T. (M-F)

7:30 A.M. to 5:00 P.M., C.S.T. (M-F)

E-mail: techsupport@orientalmotor.com

www.orientalmotor.com

Headquarters and Düsseldorf Office

Tel:0211-52067-00 Fax:0211-52067-099

Tel:01256-347090 Fax:01256-347099

Tel:01 47 86 97 50 Fax:01 47 82 45 16

Tel:02-93906346 Fax:02-93906348

Tel:(02)8228-0707 Fax:(02)8228-0708

Tel:+65-6745-7344 Fax:+65-6745-9405

Tel:(03)22875778 Fax:(03)22875528

KOREA

Tel:080-777-2042 Fax:02-2026-5495

Headquarters Tokyo, Japan

Tel:03-6744-0361 Fax:03-5826-2576

Tel:+66-2-251-1871 Fax:+66-2-251-1872

Tel:400-820-6516 Fax:021-6278-0269

T-EMU1238M-□-G

• Finger guard 1 pc

• Mounting screw set 1 set

• Cable for alarm 1 pc

2 m (6.6 ft.)

Screw 4 pcs, nut 4 pcs

• Fan 1 pc

• Power supply cable 1 pc

• OPERATING MANUAL 1 copy

(this manual)

Fan kit model :

EMU1238M-□

• Cable for alarm 1 pc

2 m (6.6 ft.)

• Fan 1 pc

• Power supply cable 1 pc

• OPERATING MANUAL 1 copy

(this manual)

Model :

Oriental motor EMU1238 取扱説明書

ブランド: Oriental motor

モデル: EMU1238

タイプ: 取扱説明書

このマニュアルも適しています

PDFをダウンロードします

報告

他の言語で

English: Oriental motor EMU1238 Operating instructions

Oriental motor EMU1238 取扱説明書

このマニュアルも適しています

Oriental motor EMU1238 取扱説明書

他の言語で

関連論文

その他のドキュメント