Philips DE5205/00 ユーザーマニュアル

EN User manual 1 ZH-S 用户手册 19

4241 210 89184

DE5205

DE5206

1 2

a b c d e f g h i

g

a

b

c

d

e

f

i

h

j k

l

m

n

3s

3S

3s

1EN

English

Contents

1 Important 2

Safety 2

2 Your Philips 2-in-1 Air

Dehumidier and Purier 6

Product Overview (g.a) 6

Controls Overview (g.b) 6

3 Getting started 7

Installing the lter 7

Positioning the

dehumidier 7

4 Using the dehumidier 8

The air quality light 8

Turning on and o 8

Setting the humidity level 8

Changing the fan speed 9

Using the purication only

mode 9

Using the swing function 10

Setting the Timer 10

Defrosting the

dehumidier 10

Setting the child lock 11

Using the light on/o

function 11

5 Draining the dehumidier 11

Emptying the water tank 11

Using the continuous

drainage 11

6 Cleaning 12

Cleaning the body of the

dehumidier 12

Cleaning the water tank 13

Cleaning the pre-lter 13

Cleaning the air quality

sensor 14

7 Replacing the HEPA lter 14

HEPA lter replacement

indicator 14

Replacing the HEPA lter 14

8 Storage 15

9 Troubleshooting 16

10 Guarantee and service 18

Order parts or accessories 18

11 Notices 18

Electromagnetic elds

(EMF) 18

Recycling 18

2 EN

1 Important

Safety

Read this user manual carefully before

you use the dehumidier, and save it for

future reference.

Danger

• Do not spray any

ammable materials such

as insecticides or fragrance

around the dehumidier to

avoid electric shock and/or

a re hazard.

• Do not drink the

accumulated water, use

it to feed animals, nor to

water plants. Empty the

water tank, and pour the

water down the drain.

Warning

• Check if the voltage

indicated on the bottom

or indicated at the rear of

the appliance corresponds

to the local power voltage

before you connect the

appliance.

• Connect the dehumidier

to the power socket

exclusively, and do not

connect it through an

extension cord to prevent

re hazard and/ or electric

shock.

• If the power cord is

damaged, you must have

it replaced by Philips, a

service center authorized

by Philips, or similarly

qualied persons in order

to avoid a hazard.

• Do not use the appliance

if the plug, the power cord,

or the appliance itself is

damaged.

• This appliance is not

intended for use by

persons (including

children) with reduced

physical sensory or mental

capabilities, or lack of

experience and knowledge,

unless they have been

given supervision or

instruction concerning

use of the appliance by a

person responsible for their

safety.

• Children should be

supervised to ensure that

they do not play with the

appliance.

• Do not start or stop the

dehumidier by plugging

and unplugging the power

cord.

3EN

English

• Do not block the air inlet

and outlet, e.g. by placing

items on the air outlet or in

front of the air inlet.

• Do not insert your ngers

or objects into the air inlet

and outlet to prevent

physical injury or product

malfunction.

Caution

• Do not turn the appliance

on and o frequently.

• If the power socket used

to power the dehumidier

has poor connections, the

plug of the dehumidier

becomes hot. Make sure

you plug the dehumidier

into properly connected

power socket.

• Always place and use the

dehumidier on a dry,

stable, level, and horizontal

surface.

• Leave at least 40 cm free

space behind and on both

sides of the dehumidier

and leave at least 60

cm free space above it.

Insucient ventilation may

cause overheating or re

hazard.

• Do not use this

dehumidier when you

have used indoor smoke-

type insect repellents or in

places with oily residues,

burning incense, or

chemical fumes.

• Do not operate or store the

dehumidier under direct

sunlight.

• Do not use the

dehumidier near gas

appliances, heating devices

or replaces.

• Do not use the

dehumidier in a bathroom

or other places where it is

likely to come in contact

with water, or wash it with

water.

• When you use the

dehumidier for drying

laundry, hang your clothes

from a distance where

water droplets will not drip

onto the dehumidier.

• The dehumidier is only

intended for household use

under normal operating

conditions (5°C - 35°C).

• Do not use the

dehumidier in a room

with major temperature

changes.

4 EN

• Do not stand on, sit

on, or lean against the

dehumidier. This may

cause the dehumidier to

tip over causing injury.

• Do not remove or dismantle

the oat in the tank;

otherwise, the dehumidier

cannot detect when the

tank is full and could result

in water leakage.

• Do not use detergents,

cleaning agents, abrasive

powders, chemically

treated dusters, gasoline,

benzene, thinners or other

solvents, as they can

damage the dehumidier

or the water tank. This may

result in water leakage.

• Mildew may form in the

water tank, clean it every

week with tap water. Then,

wipe with a soft, dry cloth.

• If you do not use the

dehumidier for an

extended period of time,

make sure all parts are

clean and dry.

• Do not use the dehumidier

for food preservation, art or

scientic works.

• Do not point the airow of

the dehumidier directly at

• Run the power cord under

carpeting, rugs, or runners.

Arrange the cord away

from areas where it may be

tripped over.

• Make sure the lters and

the water tank are properly

installed before you switch

on the dehumidier.

• Do not touch the swing

louver.

• Avoid knocking against the

dehumidier (the air inlet

and outlet in particular)

with hard objects.

• Always unplug the

dehumidier after use and

before you move or clean it.

• Power o and unplug

the dehumidier before

draining the water from the

tank. Otherwise, this may

result in water leakage.

• Always move the

dehumidier in an upright

position with handle, and

do not carry it horizontally.

• Do not drop the

dehumidier as this may

cause personal injury, and

damage to the oor or

household items as a result

of water spillage.

• Do not place anything on

top of the dehumidier.

5EN

English

condensation inside the

dehumidier.

• To prevent interference,

place the appliance at least

2m away from electrical

appliances that use

airborne radio waves such

as TVs, radios, and radio-

controlled clocks.

• The appliance does not

remove carbon monoxide

(CO) or radon (Rn). It

cannot be used a safety

device in case of accidents

with combustion processes

and hazardous chemicals.

• Never move the appliance

by pulling the power cord.

• This appliance is not

a substitute for proper

ventilation, regular vacuum

cleaning, or use of an

extractor hood or fan while

cooking.

• If the appliance is not used

for a long period of time,

remove the HEPA lter from

the dehumidier and store

it separately in a cool, dry

place.

• Do not sit or stand on the

appliance. The appliance

is equipped with unilateral

rotating wheels. Sitting or

standing on the appliance

may lead to potential injury.

Fuse Specication:

2010 T2.0A 250V

2010 T3.15A 250V

the body for a prolonged

period of time, especially

where there is someone

who is unable to adjust

the humidity. For instance:

infant, child, or elderly

person. This may harm the

physical condition and

lead to dehydration.

• Use the dehumidier with

cautions where the walls,

furniture, and art works are

vulnerable to dry air.

• Do not place the

appliance directly below

an air conditioner to

prevent condensation

from dripping onto the

appliance which will cause

short circuit and leakage of

electricity.

• Only use the original

Philips lters specially

intended for this appliance.

Do not use any other lters.

• Burning the lter may

cause irreversible damage

to humans or other

creatures. Do not use the

lter as fuel or for similar

purposes.

• Always lift or move the

appliance by the handle at

the top of the appliance.

• Do not use the

dehumidier in a room

with major temperature

changes, as this may cause

6 EN

2 Your Philips 2-in-1 Air Dehumidifier

and Purifier

Congratulations on your purchase, and welcome to Philips!

To fully benet from the support that Philips oers, register your product at

www.Philips.com/welcome.

Product Overview (g.a)

a Handle h Unilateral rotating wheels

b Louver i Display panel

c Air outlet j Continuous drainage outlet

d Air quality sensor k Power cord

e Air quality light l Rear cover with air inlet

f Water tank m Pre-lter

g Hose n NanoProtect lter HEPA Series 1

(FY1119)

Controls Overview (g.b)

a On/o button f Humidity level setting button

b Child lock button g Light on/o button

c Auto swing button h Purication ONLY button

d Fan speed button i Timer button

e Display screen

Display panel

HEPA lter replacement alert Auto mode icon

Auto defrosting indicator Laundry drying mode icon

Water tank full alert Continuous mode icon

Pre-lter cleaning alert Purication ONLY mode icon

7EN

English

Positioning the

dehumidier

To increase the dehumidifying

eectiveness, position the dehumidier

in a location that can draw the most air.

Note

• When the dehumidier is operating,

do not open exterior doors or

windows.

3 Getting started

Installing the lter

Note

• Make sure that the appliance is

unplugged before installing the

lter.

Before using the appliance, remove all

packaging materials from the lter and

place the lter into the appliance as

described as follows.

1 Pull the top part of the rear panel to

remove it from the appliance

(g.c).

2 Take out the HEPA lter and the

pre-lter (g.d).

3 Remove all packaging materials

from the HEPA lter (g.e).

4 Place the HEPA lter into the

dehumidier and then the pre-lter

(g.f).

Note

• Make sure that the HEPA lter and

the pre-lter are properly attached

to the dehumidier.

5 Reattach the rear cover by pressing

the bottom part of the rear cover

onto the appliance rst (1). Then,

gently push the rear cover against

the body of the appliance (2)

(g.g).

6 Wash your hands thoroughly after

installing lters.

8 EN

2 Touch the button once to turn on

the appliance (g.h).

» The current humidity level is

displayed on the screen.

» After measuring the air quality

for a short time, the air quality

sensor automatically selects the

color of the air quality light.

» The dehumidier goes to combi

AUTO mode.

3 Touch and hold for 3 seconds to

turn o the appliance.

Setting the humidity

level

You can set the desired humidity level

to 40, 50, 60, 70, or 80 percent.

1 Touch the button one or more

times to set the desired humidity

level, and the humidity indicator

lights up (g.i).

Note

• When the humidity is decreased to

the selected level, the dehumidier

automatically stops dehumidifying

the air, but the fan will continue

working.

• If you do not set the humidity level,

the default humidier is 60%.

• You can touch the button for

5 seconds to display the current

ambient temperature.

Tip

• A comfortable humidity level is from

40RH% to 60RH%.

4 Using the

dehumidifier

The air quality light

Color of the air

quality light

Air quality level

Blue Good

Blue-violet Fair

Red-purple Unhealthy

Red Very unhealthy

The air quality light automatically goes

on when the appliance is switched on,

and lights up all colors in sequence.

In a short time the air quality sensors

select the color that corresponds to

the surrounding air quality of airborne

particles.

Turning on and o

Note

• For optimum performance, close

doors and windows.

• Keep curtains away from the air

inlet or air outlet.

• For optimum dehumidication

eciency, place the dehumidier in

a at, stable surface.

• Before turning on the dehumidier,

check if the power voltage

corresponds to the voltage printed

on the dehumidier.

1 Put the plug of the dehumidier in

the wall outlet.

» The dehumidier beeps.

9EN

English

Note

• Do not point the airow of the

dehumidier directly at the body

for a prolonged period of time,

especially where there is someone

who is unable to adjust the

humidity.

• When you use the dehumidier

for laundry drying, hang your

clothes from a distance where

water droplets will not drip onto the

dehumidier.

• Make sure the air inlet and outlet

are not blocked by the clothes.

• Make sure that you dry the clothes

on a safe and secure place from

dropping to block the air inlet and

outlet.

Tip

• Direct the louvre until air ows

directly onto the clothes to dry your

clothes more eciently.

Using the purication

only mode

The appliance can be used in

purication only mode.

1 Press the button to access

purication only mode (g.n).

» The appliance operates under

auto mode by default.

» The dehumidifier will stop

dehumidifying the air.

» The and the display on

the screen.

Continuous mode

In continuous mode, the appliance

constantly works with the optimal

dehumidifying settings.

1 Touch the button repeatedly to

select the continuous mode (g.j).

» The and display on the

screen.

Changing the fan speed

You can select the desired fan speed

(Auto,1, 2 ,3 and 4), or clothes dry

mode.

Auto

• Touch the fan speed button

repeatedly to select the auto mode

(g.k).

Note

• You can adjust the humidity settings

manually by touching the button.

Manual

• Touch the fan speed button

repeatedly to select the fan speed

you need (g.l).

Laundry drying mode

• Touch the button until is

displayed to select the laundry

drying mode (g.m).

» The dehumidier goes to

laundry drying mode.

» The dehumidier operates under

the highest fan speed.

»

and display on the screen.

10 EN

2 Touch the fan speed button to

select the desired fan speed (g.o).

» The fan speed and display

on the screen.

3 Touch the button again to exit

the purication only mode.

» The dehumidier goes to combi

AUTO mode.

Note

• Whenever the current mode of

appliance works, it goes to

purication only mode when

touching the button.

• Humidity setting and laundry drying

mode are o in the purication only

mode.

Using the swing function

The louver is able to swing up to 90

degrees. Use the swing function to

direct the air ow.

1 Touch the button to activate the

swing function (g.p).

2 Touch the button again to

deactivate the swing function.

Tip

• After the appliance is turned on,

turn the louver upward to increase

the dehumidifying eciency.

Setting the Timer

With the timer function, you can let

the dehumidier operate for a set

number of hours. When the set time has

elapsed, the dehumidier automatically

stops dehumidifying the air, but remains

on. The timer is available from 1 to

9 hours.

1 Touch the button to activate the

timer (g.q).

2 Touch the button repeatedly to

choose the number of hours you

want the dehumidier to operate

(g.r).

• To deactivate the timer function,

touch the button repeatedly

until is displayed on the

screen.

Defrosting the

dehumidier

Note

• The defrosting function is enabled

only when the dehumidier

operates under dehumidifying

mode.

The dehumidier is equipped with a

defrosting sensor to make sure it is in

optimal condition when being used

in cold weather. The dehumidier

automatically detects if defrosting is

required.

When defrosting is required:

» The indicator is on (g.s).

» Defrosting will begin defrosting

and continue until the

dehumidier is completely

defrosted.

11EN

English

Note

• During defrosting, the dehumidier

operates in clothes dry mode.

• The dehumidier will resume

working and operate the previous

settings after defrosting is

completed.

Setting the child lock

1 Touch and hold the child lock

button for 3 seconds to activate

child lock (g.t).

» "L" displays on the screen for

3 seconds.

» When the child lock is on,

all the other buttons are not

responsive.

2 Touch and hold the child lock

button for 3 seconds again to

deactivate child lock (g.u).

» "UL" displays on the screen for

3 seconds.

Using the light on/o

function

With the light on/o button, you can

switch on or o the air quality light,

the display screen and the function

indicators if desired.

1 Touch the light on/o button

once, the air quality light will go o.

2 Touch the light on/of button

again, the display screen will

dimmed.

3 Touch the light on/o button for

the third time, all lights will be on

again.

5 Draining the

dehumidifier

Emptying the water tank

When the water tank is full:

» The appliance beeps, and the

indicator is on.

» The appliance goes to purication

only mode automatically.

1 Place your ngers in the side recess

of the dehumidier, and gently pull

the water tank out. Hold the sides of

the water tank, and remove it from

the dehumidier (g.v).

2 Empty the water into a sink (g.w).

3 Wipe the outside of the water tank

dry with a clean cloth (g.x).

4 Put the water tank back into the

dehumidier (g.y).

Note

• The dehumidier will resume

working after the water tank is

emptied.

Using the continuous

drainage

The dehumidier can also drain excess

water by attaching a hose. This allows

you to operate the dehumidier without

emptying the water tank.

1 Turn o the dehumidier and

unplug from the wall outlet.

2 Open protective cover of the

drainage hole (g.z).

12 EN

6 Cleaning

Note

• Always turn the appliance o and

unplug the appliance from the

electrical outlet before cleaning.

• Never immerse the appliance in

water or any other liquid.

• Never use abrasive or aggressive

cleaning agents such as bleach

or alcohol to clean any part of the

appliance.

• Only the pre-lter is washable. The

air purication lter is not washable.

• Do not attempt to clean the lter or

air quality sensor with a vacuum.

Cleaning the body of the

dehumidier

Regularly clean the inside and outside

of the dehumidier to prevent dust from

collecting.

1 Use a soft, dry cloth to clean both

the interior and exterior of the

appliance.

2 The air outlet can also be cleaned

with a dry, soft cloth.

3 Remove the water tank from the

dehumidier (g.v).

4 Insert the Philips provided hose into

the drainage hole (g.{).

5 Push the protective cover of

drainage outlet rightwards to open

it (g.|).

6 Connect the hose to the drainage

outlet (g.}).

7 Put the water tank back into the

dehumidier (g.y).

Note

• Put the water tank back in to

the dehumidier even using

the continuous drainage, or the

dehumidier can not operate

normally.

• Make sure the hose ts tightly

so that no water leaks from the

dehumidier.

• When using the continuous

drainage, make sure the hose is laid

at and not knotted.

• Make sure the hose is not immersed

in water, nor raised higher than the

continuous drainage hole.

• Place the outlet of the hose in

somewhere it can easily drain.

• Check the dehumidier once a week

when draining water continuously

or left unattended for an extended

period of time.

13EN

English

5 Allow the pre-lter to air dry

thoroughly before placing back in

the dehumidier.

Note

• To optimize the lifetime of the

pre-lter, make sure it dries

completely after cleaning.

• Wash your hands after handling the

lter.

6 Put the pre-lter back into the

appliance (g.‚).

7 Reattach the rear panel by pressing

the bottom part of the rear panel

onto the appliance rst (1). Then,

gently push the panel against the

body of the appliance (2) (g.g).

8 Put the plug of the dehumidier in

the wall outlet.

9 Touch and hold the timer button

for 3 seconds to reset the pre-lter.

10 Wash your hands thoroughly after

cleaning the lter.

Cleaning the water tank

Clean the water tank every day to keep

it clean.

1 Switch o the dehumidier and

unplug from the electrical outlet.

2 Remove the water tank from the

dehumidier (g.v).

3 Fill the water tank for 1/3 with water

(g.~).

4 Add some mild washing-up liquid

to the water in the water tank.

5 Wash the water tank under a

running tap water, and clean the

insides of it with a soft clean cloth

(g.).

6 Wipe the outside of the water tank

dry with a clean cloth (g.x).

7 Put the water tank back into the

dehumidier (g.y).

Cleaning the pre-lter

Clean the pre-lter when F0 and are

displayed on the screen.

Note

• The pre-lter is washable and

vacuum cleanable.

1 Switch o the dehumidier and

unplug from the electrical outlet.

2 Hold the dehumidier and pull the

top part of the rear cover towards

you (g.c).

3 Detach the pre-lter from the

appliance (g.€).

4 If the pre-lter is very dirty, use a

soft brush to brush away the dust.

Wash the pre-lter under a running

tap water (g.).

14 EN

7 Replacing the

HEPA filter

HEPA lter replacement

indicator

This dehumidier is equipped with a

lter replacement indicator to make sure

that the air lter is in optimal condition

when the dehumidier is operating.

When the HEPA lter needs to be

replaced, the HEPA lter replacement

alert displays on the screen.

If the HEPA lter is not replaced in

14 days, the dehumidier will stop

operating and automatically lock.

You need to replace the HEPA lter

immediately.

Replacing the HEPA lter

Note

• The HEPA lter is not washable nor

reusable.

• Always turn o the dehumidier and

unplug from the electrical outlet

before replacing the HEPA lter.

• Do not clean the HEPA lter with a

vacuum.

Replace the HEPA lter when A3 and

display on the screen.

1 Switch o the dehumidier and

unplug from the wall outlet.

2 Take out the used HEPA lter

according to the lter alert light

status displayed on the screen.

Discard used lters (g.‡).

Cleaning the air quality

sensor

Clean the air quality sensor every

2 months for optimal functioning of the

dehumidier.

Note

• If the humidity level in the room

is very high, condensation may

develop on the air quality sensor

and the air quality light may indicate

a more poor air quality even though

the air quality is actually good. If this

occurs, clean the air quality sensor

or use the dehumidier on a manual

speed setting.

• If the dehumidier is used in a dusty

environment, it may need to be

cleaned more often.

1 Switch o the dehumidier and

unplug from the wall outlet.

2 Clean the air quality sensor inlet and

outlet with a soft brush (g.ƒ).

3 Remove the air quality sensor cover

(g.„).

4 Clean the air quality sensor, the

dust inlet and the dust outlet with a

damp cotton swab (g.…).

5 Dry all parts thoroughly with a dry

cotton swab.

6 Reattach the air quality sensor cover

(g.†).

15EN

English

Note

• Do not touch the pleated HEPA lter

surface, or smell the lters as they

have collected pollutants from the

air.

3 Remove all packaging material from

the new HEPA lter (g.e).

4 Place the new HEPA lter into the

appliance (g.ˆ).

5 Put the plug of the dehumidier in

to wall outlet.

6 Touch and hold the timer button

for 3 seconds to reset the lter

lifetime counter.

7 Wash your hands thoroughly after

changing the HEPA lter.

8 Storage

1 Turn o the dehumidier and

unplug from the wall outlet.

2 Clean the dehumidier, air quality

sensor, empty the water tank and

wash the pre-lter (see chapter

‘Cleaning’).

3 Let all parts dry thoroughly before

storing.

4 Wrap the lter and pre-lter

separately in air tight plastic bags.

5 Store the dehumidier, lters and

pre-lter in a cool, dry location.

6 Always thoroughly wash hands after

handling lters.

16 EN

9 Troubleshooting

This chapter summarizes the most common problems you could encounter with the

dehumidier. If you are unable to solve the problem with the information below, visit

www.philips.com/support or contact the Consumer Care Center in your country

for assistance.

Problem Possible solution

The appliance

does not work

even though it is

plugged in to the

wall outlet and

switched on.

• The timer is set to a specic time interval. Reset or turn o

the timer.

• Try a dierent electrical outlet or check the wall switch.

• Make sure that the water tank is empty and placed in the

dehumidier properly.

• The lter alert status is displaying the lter code. Replace

the corresponding lter and reset the lter lifetime counter

(see chapter "Replacing the lter").

The dehumidier

does not work

even though it is

switched on.

• The lter replacement indicator has been on continuously

but you have not replaced the corresponding lter, and the

appliance is now locked. In this case, replace the lter and

reset the lter lifetime counter.

The water tank is

empty but the

indictor is still on.

• Remove the water tank from the dehumidier and place it

back to the dehumidier again.

There is no air

dehumidication

in the room or the

dehumidifying

eectiveness is

low.

• Make sure that the lters are clean and in good condition.

• Make sure the air inlet and outlet are not blocked.

• The room humidity is below what the dehumidier is set to.

Select a lower humidity level.

• Make sure that no exterior doors or windows are open.

• The current temperature is low in the room. Try again until

the temperature rises up.

Water leaks from

the dehumidier.

• Make sure that the dehumidier is in good condition and

the water tank is not cracked.

The dehumidier

does not collect

water.

• The humidity is low. The dehumidier automatically

resumes working when the humidity level is increased.

• The temperature is low. Wait until the temperature rises up.

17EN

English

Problem Possible solution

The airow that

comes out of

the air outlet

is signicantly

weaker than

before.

• The pre-lter is dirty. Clean the pre-lter (see chapter

"Cleaning").

The air quality

does not improve,

even though the

appliance has

been operating for

a long time.

• One of the lters has not been placed in the appliance.

Make sure that all lters are properly installed in the

following order, starting with the innermost lter:

1) NanoProtect lter HEPA Series 1 (FY1119); 2) pre-lter.

• The air quality sensor is wet. Make sure that the air quality

sensor is clean and dry (see chapter "Cleaning").

The color of the air

quality light always

stays the same.

• The air quality sensor is dirty. Clean the air quality sensor

(see chapter "Cleaning").

The dehumidier

produces a

unpleasant smell.

• The rst few times you use the dehumidier, it may

produce a plastic smell. This is normal. The dehumidier

may also produce an unpleasant smell when the lter is

dirty. In this case, clean or replace the appropriate lter.

• If the dehumidier produces a burnt odor, switch OFF and

unplug from the electrical outlet. Contact the Consumer

Care Center in your country for assistance.

The dehumidier

is loud.

• If the dehumidier is too loud, change the fan speed to

a lower fan speed level. When using the product in a

bedroom at night, choose a lower fan speed.

• Make sure that the dehumidier is placed on a at and

stable surface.

The dehumidier

still indicates that

I need to replace a

lter, but I already

did.

• Perhaps you did not reset the lter lifetime counter. Plug

in the dehumidier, touch to switch on the dehumidier,

and touch and hold the timer button for 3 seconds.

Error codes "E1",

"E2", "E3" “E4” or

"E5" displays on

the screen.

• The dehumidier has malfunctions. Contact the Consumer

Care Center in your country.

18 EN

11 Notices

Electromagnetic elds

(EMF)

This Philips appliance complies with all

applicable standards and regulations

regarding exposure to electromagnetic

elds.

Compliance with EMF

Koninklijke Philips N.V. manufactures

and sells many products targeted at

consumers, which, like any electronic

apparatus, in general have the ability to

emit and receive electromagnetic signals.

One of Philips’ leading Business

Principles is to take all necessary health

and safety measures for our products,

to comply with all applicable legal

requirements and to stay well within the

EMF standards applicable at the time of

producing the products.

Philips is committed to develop,

produce and market products that

cause no adverse health eects. Philips

conrms that if its products are handled

properly for their intended use, they

are safe to use according to scientic

evidence available today.

Philips plays an active role in the

development of international EMF

and safety standards, enabling Philips

to anticipate further developments in

standardization for early integration in

its products.

Recycling

Do not throw away the product with

the normal household waste at the

end of its life, but hand it in at an

ocial collection point for recycling.

By doing this, you help to preserve the

environment.

Follow your country's rules for the

separate collection of electrical and

electronic products. Correct disposal

helps prevent negative consequences

for the environment and human health.

10 Guarantee and

service

If you need information or if you have a

problem, please visit the Philips website

at www.philips.com or contact the

Philips Consumer Care Center in your

country (you can nd its phone number

in the worldwide guarantee leaet). If

there is no Consumer Care Center in

your country, go to your local Philips

dealer.

Order parts or

accessories

If you have to replace a part or want to

purchase an additional part, go to your

Philips dealer or visit www.philips.com/

support.

If you have problems obtaining the

parts, please contact the Philips

Consumer Care Center in your country

(you can nd its phone number in the

worldwide guarantee leaet).

ページが読み込まれています...

Philips DE5205/00 ユーザーマニュアル

このマニュアルも適しています

Philips DE5205/00 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント