LG MD19GQGA1 ユーザーガイド

www.lg.com

MFL68026024

Rev.01_101818

OWNER’S MANUAL

DEHUMIDIFIER

Please read this manual carefully before operating your set and retain it for future

reference.

MD19GQGA1 / MD16GQSA1

中文

ENGLISH

2

SAFETY PRECAUTIONS

ENGLISH

SAFETY PRECAUTIONS

The following safety precautions are intended to prevent accidental property damage and per-

sonal injury through safe and correct use of the product.

WARNING

Failure to follow the instructions could result in death or serious injury of the user.

CAUTION

Failure to follow the instructions could result in personal injury or property damage.

WARNING

When installing the dehumidifier

• Do not damage, alter, excessively bend, twist, pull, pinch or heat the power cord.

If the power cord is damaged, request for repair to the service technician to prevent any risk.

If not, it can cause fire, electric chock or product failure.

• Do not use multiple-outlet adaptors with this dehumidifier.

Excessive use of power could result in electric shock or fire.

• Do not use the product if the outlet is damaged or loose.

Doing so could result in electric shock or fire.

• If there is a gas leak, open the window for ventilation before using the dehumidifier.

Failure to do this could result in explosion, fire or burns.

• Do not disassemble, repair or modify the product.

Doing so could result in fire or electric shock.

• Do not store or use flammable gases or materials near the dehumidifier.

Doing so could result in fire or product malfunction.

• This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

When using the dehumidifier

• Push the power plug all the way into the wall outlet so that it is not loose.

A loose connection could result in fire.

• Do not touch the power plug with wet hands.

Doing so could result in electric shock or injury.

• Do not modify or extend the power cord.

Doing so could result in fire or electric shock.

• If the product makes a strange noise or emits a smell or smoke, pull the power plug out

and contact the service center.

Failure to do this could result in explosion, fire or burns.

• Avoid placing the dehumidifier or other heavy objects on top of the power cord.

Doing so could result in fire or electric shock.

• Do not use water to clean the dehumidifier.

Doing so could result in electric shock or malfunction.

!

SAFETY PRECAUTIONS

3

ENGLISH

• Keep the air inlet and outlet free from obstructions.

Failure to do this could result in poor performance or malfunction.

• Do not cover the power cord with a mat etc.

If heavy objects are placed on the mat, the power cord underneath could be damaged, causing

fire or electric shock.

• Do not place combustion appliances directly in the path of the dehumidifier’s airway.

Doing so could result in incomplete combustion or deformation by heat.

• Keep the product away from fire.

Failure to do this could result in fire.

• Do not use the product in places where it could be splashed by water.

Doing so could result in fire or electric shock.

• Do not insert fingers, sticks etc. into the air inlet or outlet.

You could be injured by the high-speed fan.

• Only qualified personnel may clean the internal parts. Do not use corrosive detergents.

Doing so could result in product malfunction, fire or electric shock.

CAUTION

When installing the dehumidifier

• Do not use the product for purposes other than its intended use.

This product is not designed for preserving precision instruments, tableware or art works. The

quality of the items you are trying to preserve could deteriorate.

• Ventilate frequently.

Keep the area well ventilated, especially if you are using a combustion appliance as well. Inad-

equate ventilation reduces the oxygen level in the air.

• Always hold the plug head when pulling the power plug.

Failure to do so could result in electric shock or injury.

• Do not use excessive force when pulling the extension hose.

Doing so could result in damage to or deformation of the hose.

• Do not use the product in places where chemicals are used.

Chemicals and solvents dissolved in the air in places such as hospitals, factories, laboratories

and hair salons could cause the product to become deformed, causing the dehumidified water

to leak and wet nearby household items, equipment etc.

• Turn off the dehumidifier and pull out the power plug before cleaning.

If you do not do this, you could be injured by the high-speed fan.

• DO NOT operate the dehumidifier without a filter.

Using the product without a filter could result in a reduced product lifespan, electric shock or in-

jury.

When using the dehumidifier

• Do not use the product for preserving animals/plants, precision instruments, art works

etc.

It may cause property damage.

• Do not place vases or water jars on the dehumidifier.

If the water flows into the dehumidifier, it could result in fire or electric shock.

• Product must be placed on safe and hard surface floor.

On weak surface floor, product is prone to vibration and noise.

Product must stand upright, otherwise it causes defect and water leakage.

!

• Turn off the dehumidifier and empty the water tank before moving the dehumidifier.

The water could overflow from the tank, wetting household items or causing fire or electric

shock.

• Pull out the power plug if you will not be using the product for an extended period.

Failure to do this could result in product malfunction or fire.

• Do not use the product in a very small space such as a closet.

Poor ventilation could result in overheating or fire.

• Do not use wax, thinner or a strong detergent when cleaning. Wipe the product using a

soft cloth.

Using inappropriate cleaning products could cause the product to become discolored or de-

velop surface flaws.

• Do not use the product in direct sunlight or rain.

The product could overheat, causing fire or electric shock.

• Do not touch the product with wet hands.

Doing so could result in electric shock. Position the product on a firm, stable surface.

• If the product is on an unstable surface, it may vibrate and make noise.

If the product is tilted or laid down, the dehumidified water could overflow and the product

could malfunction.

• Do not keep the power cord tied up when using the product.

The power cord could overheat, resulting in fire.

• Do not spray foreign substances or water into the sensor hole.

This could result in electric shock or malfunction.

• Do not use the product at unstable voltage for a long period of time.

The product may stop automatically to protect itself. This could result in electric shock or mal-

function.

• Do not allow child to mount on the product.

It may cause serious injury and also product defect.

4

SAFETY PRECAUTIONS

ENGLISH

TABLE OF CONTENTS

5

ENGLISH

TABLE OF CONTENTS

2 SAFETY PRECAUTIONS

6 QUICK START

7 NAME OF EACH PART

7 Front side

7 Back side

8 Display Panel

9 CHECKLIST BEFORE

USAGE

10 HOW TO USE

11 Smart Dehumidification

12 Jet Dehumidification

12 Silent Dehumidification

13 Spot Drying

14 Laundry Drying

15 Ionizer

15 Defrost Operation

15 Auto Clean

16 Bucket full

17 OFF Timer

17 Timer function

18 Lock Function

19 How to empty water tank

20 How to Continuous Drainage Setup

21 Product registration through Wi-Fi func-

tion

22 SMART FUNCTIONS

22 Using Smart ThinQ Application

24 HOW TO CLEAN

24 How to clean the exterior and inlet of

the dehumidifier

24 How to clean water tank

25 How to clean Pre-Filter

26 HOW TO STORE

27 TROUBLESHOOTING

TIPS

28 PRODUCT SPECIFICA-

TIONS

6

QUICK START

ENGLISH

Dehumidifier efficiency varies depending on room tempera-

ture and relative humidity.

• A lower temperature and lower relative humidity will reduce the moisture removal rate.

• The compressor operates in dehumidification mode only when the set humidity is lower than the

room humidity.

The operating temperature is 5°C to 32°C.

• The dehumidifier cannot be used at 0°C or below because the dehumidified water could freeze.

• At 32°C or higher, the dehumidifier may stop running automatically to protect itself from over-

heating.

The room temperature increases while the dehumidifier is

running.

• This dehumidifier does not have temperature control functions.

• The dehumidifier generates heat while operating, raising the room temperature by about 2°C or

3°C depending on the usage conditions (room air pressure and room size).

The dehumidification can be restarted after three minutes.

• If you attempt to restart the dehumidifier immediately after stopping it, the compressor will start

running again after about three minutes for product safety reasons.

QUICK START

NAME OF EACH PART

7

ENGLISH

Start/stop button

Outlet

Louver

Display

Water tank lid

Water tank

It stores dehumidified water.

It adjusts

the direction

of the wind.

Pre-Filter

Wheels for moving

Power plug hanging part

Inlet

Hose cover

Power plug

It absorbs the air and

moisture in the room.

The components are at the top part of the product packaging box.

The form of water container may differ in each product.

Extension hose Shoes drying kit Laundry drying kit

Back side

Components

NAME OF EACH PART

Front side

8

NAME OF EACH PART

ENGLISH

Start/stop

Off Timer

Bucket full

indicator lamp

Operation mode

Humidity control Ionizer

Wind strength control

Timer

indicator lamp

Humidity &Off timer

display

Wi-Fi

indicator lamp

Buttons to turn off Wi-Fi

Start/Stop button It is used to start and stop the product operation.

Operation mode button It is used to switch to Smart dehumidification mode,

Jet dehumidification mode, Silent dehumidification mode,

Spot drying mode, and Laundry drying mode.

Smart dehumidification → Jet dehumidification → Silent

dehumidification → Spot drying → Laundry drying →

Smart dehumidification

The Auto Clean function will turn on/off after depressing

the button for 3 seconds or more.

Ionizer button It is used to remove harmful bacteria in the air. When you

press the button for 3 seconds, lock function is operated.

Humidity control button It controls the desired humidity. (30%~70%)

Humidity control can be set in the units of 5%.

Wind strength control button It controls the wind strength. When you press the button

for 3 seconds, Wi-Fi pairing is operated.

Buttons to turn off Wi-Fi Pressing and holding the Start/Stop button and the Wind

strength control button at the same time for more than 3

seconds turns off Wi-Fi.

After finishing product registration and while Wi-Fi is off,

pressing and holding the button for more than 3 seconds

turns on Wi-Fi and you can control the product from your

smart-phone that has been previously registered.

Off Timer button The product will be turned off after the set time.

When the button is pressed, it is increased by 1 hour each

time, and you can set up to 8 hours.

Operation mode lamp It displays the currently set operation mode.

Humidity & Off timer display

It displays the current humidity and set humidity. When Off

timer is set, it displays the Off timer time, and it automatically

displays the current humidity after completing the setting.

Wi-Fi indicator lamp It is displayed when Wi-Fi function is set.

Timer indicator lamp It is displayed when timer is set in Wi-Fi app.

Set indicator lamp It is displayed when humidity is set.

Desired humidity is displayed with "Set" light, and the light

is turned off when showing current humidity.

Display Panel

CHECKLIST BEFORE USAGE

9

ENGLISH

Dehumidification amount changes according to indoor temperature and

relative humidity.

- If the temperature or relative humidity is low, dehumidification amount is decreased.

- Dehumidification is performed with compressor operation only when the desired humidity is

lower than the current humidity.

The product can operate in the temperature boundary of 5°C~32°C.

- At 0°C or less, dehumidified water will freeze, and dehumidification cannot be performed.

- If it is over 32°C, the temperature inside the dehumidifier will rise, and there will be cases of

stopping the operation by protective device activation to avoid excessive usage.

When the dehumidifier is under operation, the indoor temperature will rise.

- Dehumidifier does not have a cooling/heating function.

- Heat is generated during the operation, so the temperature may be increased by about 2°C~3°C

according to the usage conditions (indoor temperature, size of the room).

Operation will restart after 3 minutes.

- If it is restarted right after the stop, the compressor will start about 3 minutes after to protect the

product.

It automatically protects the product during the continuous operation.

If it is operated for 24 hours or more continuously, the compressor will stop automatically to pro-

tect the product, and it will restart after 1 hour.

Please have gap of 30cm or more from the wall.

If it is not ventilated well, the air suction performance will be degraded.

There may be water remaining in the drain water tank at the first time

usage.

There may be water remaining in the drain water tank by the product outgoing inspection to check

the normal operation of the product. It is not a failure.

CHECKLIST BEFORE USAGE

10

HOW TO USE

ENGLISH

Push start/stop button.

- The louver opens and smart dehumidification starts.

But, if no other button is pressed (Mode, Speed etc.), the desired humidity will change to 50%

after 30 minutes of continuous operation.

- The current humidity is displayed on The humidity & Off timer display.

Press operation mode button to select desired operation mode among

smart dehumidification, jet dehumidification, silent dehumidification,

spot drying, and laundry drying mode.

- The selected operation indicator lamp is lighted.

- The selected operation mode starts after 3 seconds.

Press Humidity Control / button to change humidity.

- Desired humidity can be set to 30 ↔ 35 ↔ 40 ↔ 45 ↔ 50 ↔ 55 ↔ 60 ↔ 65 ↔ 70.

Humidity can be set with the units of 5%.

- During the humidity setting, desired humidity is displayed on the humidity display part, and the

current humidity is displayed after about 5 seconds.

- Current humidity is displayed in the units of 5% from 25~90%.

If it is less than 25%, it is displayed as 25%, and if it is 90% or more, it is displayed as 90%.

Press Wind Strength Control button to change wind amount.

You can set the wind amount to low or high wind.

HOW TO USE

11

ENGLISH

CAUTION

• If the product started again right after stopping the operation, dehumidification operation

does not start for about 3 minutes to protect the compressor.

!

To stop the product, press start/stop button one more time.

- Louver closes.

- All lamps will be turned off and the product stops.

Smart Dehumidification

To maintain pleasant indoor condition

- If you press Operation Mode button to select Smart dehumidification mode and set the desired

humidity, it maintains the humidity set by the user.

- Once the humidity level reaches the desired humidity, the compressor stops and only the fan

operates. If relative humidity goes up, it will operate dehumidification again.

- The wind strength is set to high wind as default, and you can set wind strength and desired hu-

midity.

12

HOW TO USE

ENGLISH

Silent Dehumidification

When you want dehumidification in silent mode

- Press Operation Mode button to select Silent dehumidification mode.

- Silent dehumidification operation makes silent and pleasant room even during the night.

- The wind strength is set to low wind as default, and you can set wind strength and desired hu-

midity.

Jet Dehumidification

When you want to remove indoor moisture quickly

- Press Operation Mode button to select Jet dehumidification mode.

- Under Jet dehumidification mode, it will change to Smart dehumidification mode after 60 minutes.

Even if it is under power wind (Po) operation, high wind indicator lamp is lighted.

- When it is in Jet dehumidification mode, if you select Humidity control button or Speed button, it

switches to Smart dehumidification.

- If it changes from Smart/Silent dehumidification to Jet dehumidification, the desired humidity se-

lected in another operation mode is set.

HOW TO USE

13

ENGLISH

How to use Spot drying mode

Open the hose cover at the back of the prod-

uct by turning it counterclockwise.

After inserting Spot drying extension hose, fix

it by turning it clockwise.

The form of water container may differ in each product.

Extend the hose to make it face the desired

drying direction.

Connect shoes drying kit or laundry drying kit to

the extension hose.

Extension hose

Spot Drying

When you need spot drying of shoes, closet, etc.

- Press Operation Mode button to select Spot drying mode.

- In Spot drying mode, the louver is closed.

- Wind amount is set to high wind, and humidity control & the wind amount is not operational.

- The current humidity is displayed in the humidity display window.

-

Use the product by connecting shoes drying / laundry drying kit through the extension hose as necessary.

14

HOW TO USE

ENGLISH

CAUTION

• Do not move the dehumidifier by holding the extension hose. Dehumidifier may fall down

and cause injury.

• If spot drying operation is used for long period of time, the operation may stop to protect the

product.

!

CAUTION

When drying laundry, be careful not to have laundry water drop on to the dehumidifier.

!

Laundry Drying

When you want to dry laundry continously regardless of the ambient humidity

- Press Operation Mode button to select Laundry drying mode.

- The wind strength is set to high at default, and you can change the wind strength. You cannot

set desired humidity.

- Louver operates up and down.

h The form of water container may differ in each product.

HOW TO USE

15

ENGLISH

Auto Clean

This function dries inside of the dehumidifer in order to prevent mold or germs.

- Press the operation mode button for about 3 seconds during operation to set up Auto Clean.

- Each time the operation mode button is pressed for 3 seconds: Auto Clean → settings cancella-

tion - then it repeats

- When running Auto Clean a is displayed on the display.

- After Auto Clean function finishes, the LED display automatically turns off.

- When the operation stops, the Auto Clean will start.

When Auto Clean function starts, the dehumidifier will run the fan for a certain period in order to

remove moisture inside the product. (Duration: about 5 minutes)

Defrost Operation

If there is frost in the heat exchanger due to low indoor temperature, it automatically re-

moves the frost.

- During the operation, if ‘dF’ is displayed on the display, it automatically runs the defrost in the

heat exchanger inside the product.

- Compressor is stopped during the automatic defrost operation.

Ionizer

When you want to remove harmful bacteria in the air

- Select it by pressing Ionizer button.

- It removes harmful material in the air such as bacteria, virus, etc. using ionized air.

- You can use Ionizer function and dehumidification function at the same time.

- Ionizer can be used at any time regardless of dehumidifier function.

16

HOW TO USE

ENGLISH

CAUTION

Cautions when you drain the water

Carefully take out the drain water tank.

If you pull the water tank too hard, the water inside may spill over.

When you take out the water tank, make sure to stop the product.

If you take out the water tank during the operation, compressor will

stop, and fan will operate for 5 minutes to vaporize the remaining

condensed water in the heat exchanger before stopping the opera-

tion.

!

CAUTION

• Lamp will turn on if water tank is not correctly placed. Check if water tank fully and correctly

placed.

• When you move the product or shock is imposed to the product, Bucket full lamp may be

lighted.

• Drain the water inside the water tank, and reassemble the water tank.

!

Bucket full

When the water tank is full, operation automatically stops, bucket full lamp is lighted, and

warning buzzer sounds.

(Warning buzzer will sound one more time after 1 minute.)

- When the full water is detected, the dehumidification function immediately stops, and fan oper-

ates for 5 minutes to remove the remaining condensed water.

- Bucket full lamp is lighted on the display panel, and the product operation stops.

- After draining, when you insert water tank again, bucket full lamp is turned off, and operation

starts again automatically.

h The form of water container may differ in each product.

HOW TO USE

17

ENGLISH

CAUTION

Drain the water inside the water tank and then set the time.

If water tank becomes full during Off Timer operation, bucket full indicator lamp is lighted

and the dehumidification stops.

!

To cancel Off Timer

- If you press Off Timer button repeatedly until the time display disappears in the Off Timer dis-

play part, it will be cancelled.

Timer function

Various kinds of reservation including the power on/off can be made by the Smart ThinQ

application. (Execute Smart ThinQ Application → Select the dehumidifier product → Make reser-

vation)

* For more detailed description on the use of Smart ThinQ, refer to the Using the Smart Functions

section.

* You can set the timer time through app.

• You can set the timer function only through Smart ThinQ app.

Off Timer

Check if it is under operation and press Off Timer button.

- Off Timer switches in the following order, so select the setting time.

(1 hour gap)

1 2 8 No display

- The remaining time is displayed as time goes.

- When it passes the selected time, operation stops.

When timer function is set through app, the

timer set display part is lighted.

18

HOW TO USE

ENGLISH

Lock Function

Press the Ionizer button for 3 seconds.

- If you take off your hand when the buzzer sounds 1 time after 3 seconds, it enters Lock function.

- “CL” display in the display panel is maintained for 5 seconds.

- It maintains the operation state at the time of setting the function until the function is turned off,

and there will be no response even if a button is pressed.

- If you press other buttons in Lock function set state, warning sound is generated 3 times, and

‘CL’ display is displayed in the display panel for 5 seconds.

- You can set the function regardless of whether the product is in operation.

To unlock

- Press the Ionizer button for 3 seconds.

- After 1 buzzer sound after 3 seconds, if you take off your hand, the lock function will be turned

off.

HOW TO USE

19

ENGLISH

CAUTION

• If the water tank is taken out right after stopping the operation, there are cases of water re-

maining in the heat exchanger dropping into the main unit. (Wipe the dropped water with

soft cloth.)

• After taking out the water tank, do not touch inside the main unit. It will cause failure of the

full water detection device.

• Periodically clean inside the water tank (about 1 time per week).

• If it is used during winter or at low temperature, there is less moisture in the air, so dehu-

midification amount is also decreased.

• When you take out the water tank, make sure to stop the product. If you take out during op-

eration, the compressor will stop and the fan operates for 5 minutes to vaporize the re-

maining condensed water inside the heat exchanger before complete stop.

!

Hold the top handle of the water tank and

softly take it out.

Open the drain lid of the water tank.

First insert the bottom part of the water tank

correctly into the hole, and then push it in.

Pour out the water inside the water tank.

Drain lid

Water tank

handle

Water tank

handle

How to empty water tank

h The form of water container may differ in each product.

ENGLISH

CAUTION

• Be careful of the cut part around the continuous drainage hole when connecting or separat-

ing the continuous drainage hose. The cut part is sharp, and it may cause injury.

• Take care not to injure hands while connecting drainage hose.

• The product does not work without the water bucket installed.

!

Separate the water bucket from the product. Open the continuous drainage hole at the back of

the product.

- Cut the continuous drainage hole with a nipper.

- Caution should be taken that the cut part will not

fall into the continuous drainage hole.

Insert the water bucket into the product.

- If the water bucket is not inserted, the product will

not operate.

Insert the continuous drainage hose into the contin-

uous drainage hole and connect it to the drain hole

on the product.

※The form of water container may differ in each product.

- The continuous drainage hose is sold separately. If you wish to use a commercial hose available in the

market, use a hose whose internal diameter is 16 mm.

- Check if the continuous drainage hose is connected to the drain hole on the product correctly. If the contin-

uous drainage hose is not connected to the drain hole on the product correctly, water may leak when dehu-

midification is carried out.

- Items Needed: 16mm (Inner diameter) hose nearby sink or drain.

Continuous

drainage hose

How to Continuous Drainage Setup

How to connect the hose for continuous drainage

More than

10 cm

Do not bend the continuous drainage

hose or soak it in water.

20

HOW TO USE

ページが読み込まれています...

LG MD19GQGA1 ユーザーガイド

このマニュアルも適しています

LG MD19GQGA1 ユーザーガイド

他の言語で

関連論文

その他のドキュメント