Hach 500sc SiO2 Operations

DOC023.97.80267

5500sc SiO

2

07/2016, Edition 2

Operations

Fonctionnement

Operaciones

Operações

操作

조작

การปฏิบัติการ

English..............................................................................................................................3

Français......................................................................................................................... 19

Español.......................................................................................................................... 36

Português...................................................................................................................... 54

中文................................................................................................................................. 71

日本語............................................................................................................................. 86

한글............................................................................................................................... 103

ไทย.................................................................................................................................. 119

2

Table of contents

User interface and navigation on page 3 Configure the outputs on page 11

Startup on page 6 View data on page 15

Set up the reagents and standards on page 8 Use an SD card on page 17

Measure a grab sample or standard on page 8 Calibration on page 17

Set up the system on page 9

Safety information

Refer to the installation user manual for general safety information, hazard descriptions and

precautionary labels descriptions.

User interface and navigation

Keypad description

Refer to Figure 1 for the keypad description and navigation information.

Figure 1 Keypad description

1 Display 6 Diag: enter the DIAG/TEST MENU

2 Navigation keys RIGHT, LEFT: switch

measurement displays, select options, navigate

data entry fields

7 Cal: enter the CALIBRATE MENU

3 Navigation keys UP, DOWN: scroll menus, scroll

measurement channels, enter numbers and letters

8 Back: go back to the previous menu

4 Home: go to the main measurement screen 9 Menu: select options from the analyzer main menu

5 Enter: confirm and open sub-menus

Display description

Refer to Figure 2 for the measurement screen descriptions. Refer to Figure 3 for the system status

descriptions.

English

3

Figure 2 Measurement screen

1 Home (main measurement screen) 6 Relays (second icon shown if additional relay

installed)

2 Measurement channel 7 Parameter

3 Activity (shown during a measurement or calibration

process)

8 Measurement value

4 Reminder (for a maintenance task) 9 Channel name

5 SD card (shown when a SD card is inserted) 10 Analyzer name

Figure 3 System status screen

1 Calibration status information 3 Reagent (Rx) and standards (Sx) with fluid level

indicators (%)

1

2 PROGNOSYS service indicator bar 4 PROGNOSYS measurement quality indicator bar

PROGNOSYS indicator bars

The service indicator bar shows the number of days until a service task is necessary. The

measurement quality indicator bar shows the overall measurement health of the analyzer measured

on a scale from 0 to 100.

Color Color meaning for service indicator bar Color meaning for the measurement quality indicator

bar

Green There are at least 45 days until the next

service task is necessary.

The system is in good working condition and the health

percentage is more than 75%.

Yellow At least one service task is required in the

next 10 to 45 days.

The system needs attention to prevent a failure in the

future. The health percentage is between 50 and 75%.

Red One or more service tasks are required

within the next 10 days.

The system needs immediate attention. The health

percentage is below 50%.

1

The number of bottles shown in the display depends on the number of bottles installed.

4 English

Additional display formats

From the main measurement screen, additional display formats are available:

• Single channel analyzers:

• Push the LEFT and RIGHT arrows to switch between the main display and a graphical display.

• Multi-channel analyzers:

• Push the UP or DOWN key to display the measurement for the previous or next channel in

sequence.

• Push the RIGHT key to switch to the multi-channel display (default = 2 channels) or the LEFT

key to switch to the graphical display.

• In the multi-channel display, push the UP and DOWN keys to scroll through all channels. Push

the RIGHT key to add additional channels to the display. Push the LEFT key to remove

channels from the display.

• In the graphical display, push the UP or DOWN key to show the graph for the previous or next

channel in sequence.

Graphical display

The graph shows measurements for up to six channels at once. The graph supplies easy monitoring

of trends and shows changes in the process.

1. From the main measurement screen, push the LEFT arrow to show the graphical display.

Note: Push the UP or DOWN key to show the graph for the previous or next channel in sequence.

2. Push home to change the graph settings.

3. Select an option.

Option Description

MEASUREMENT VALUE Set the measurement value for the selected channel. Select between AUTO

SCALE and MANUALLY SCALE. Enter the minimum and maximum ppb value in

the MANUALLY SCALE menu.

DATE & TIME RANGE Select the date and time range to show on the graph: last day, last 48 hours, last

week or last month.

Power switch and SD card location

Figure 4 shows the power switch, the SD card slot and the indicator lights.

English

5

Figure 4 Power switch and SD card

1 Status indicator light 3 Analyzer ON/OFF indicator LED

2 Power switch (UP = ON)

2

4 SD card slot

Status indicator light

When the analyzer power switch is on, a status indicator light is on. Refer to Table 1.

Table 1 Status indicator definitions

Light color Definition

Green The analyzer is in operation with no warnings, errors or reminders.

Yellow The analyzer is in operation with active warnings or reminders.

Red The analyzer is not in operation due to an error condition. A serious problem has occurred.

Startup

Turn on the analyzer

1. Open the top door.

2. Pull the analytics panel open. A magnetic latch holds the panel closed.

3. Turn on the power switch on the main circuit board (refer to Figure 4 on page 6).

4. Close the analytics panel.

Start the analyzer setup

When the analyzer is powered on for the first time, or powered on after the configuration settings

have been set to their default values:

1. Select the applicable LANGUAGE.

2. Select the DATE FORMAT.

3. Set the DATE and TIME.

4. When prompted, confirm with YES to setup the analyzer.

Note: The analyzer stays in initialization mode until the configuration is complete.

5. Select the channel.

6. Select the measurement mode.

7. The setup results for the channel, sample flow, sample pressure and minimum flow are shown.

Make sure that the following values are within range:

2

Open the upper door and the analytics panel. The power switch is inside on the far right side on

the back of the analyzer.

6 English

• Sample pressure: minimum 0.14 bar (2 psi)

Note: The maximum pressure is regulated by a pressure regulator at 0.28 bar (4 psi).

• Minimum flow: 55 mL/minute

8. Push enter to confirm.

9. When prompted, make sure that the reagent bottles are full and confirm with YES.

10. When prompted, make sure that the standard bottles are full and confirm with YES.

11. Reagent 1 has a known effect on the measurement value. The value attributed to this effect is

printed on the bottle as a BLANK value. When prompted, enter this value.

Note: The analyzer setup does not configure relays, outputs, network cards, calculations or calibration parameters.

Refer to Calibration on page 17 for configuration information for calibration parameters. Refer to Configure the

outputs on page 11 for configuration information for relays, outputs or network cards. Refer to Set up the

calculation on page 10 to setup calculations.

Configure the sequencer (optional)

Option only available for the multi-channel version of the analyzer.

1. Select SETUP SYSTEM>CONFIGURE SEQUENCER.

Option Description

ACTIVATE

CHANNELS

Starts or stops measurements for individual sample sources. Use the UP and DOWN

navigation keys to scroll through the channels. Deselect a channel with the LEFT

navigation key. Push enter to confirm.

Note: Inactive channels are shown with a "~" character before the channel name on all

displays.

SEQUENCE

CHANNELS

Sets the measurement order of the sample sources. Use the UP and DOWN navigation

keys to scroll through the sequence. For each sequence number use the LEFT and

RIGHT navigation keys to select a channel. Push enter to confirm.

Calibrate the analyzer

N O T I C E

The manufacturer recommends calibration of the analyzer after 1 day of operation to allow all system components

to stabilize.

Refer to Calibration on page 17 to start a calibration.

Operation

W A R N I N G

Potential fire and explosion hazard. This equipment is intended for only aqueous type samples. Use with

flammable samples can result in a fire or explosion.

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and wear all of the personal protective

equipment appropriate to the chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

When the lower door is opened, the current measurement or calibration is stopped. When the lower

door is closed, the previous measurement or calibration starts again.

English

7

Set up the reagents and standards

Make sure to set the sample flow rate and install the reagent bottles before this task is started.

1. Push menu and then go to REAGENTS/STANDARDS.

2. Select one of the options. Use the SET options when the volume of existing reagents/standards

needs to be adjusted. Use the RESET options when reagents/standards are replaced or renewed

(bottles are replaced).

Option Description

SET REAGENT LEVEL Sets the volume of a specific reagent in the reagent bottle to an estimated value.

Range: 1–100%.

SET STANDARD LEVEL Sets the volume of a specific standard solution in the standard bottle to a

calculated approximate value. Range: 1–100%.

SET CLEANING LEVEL Sets the volume of the cleaning solution in the cleaning solution bottle to an

estimated value. Range: 1–100%.

RESET REAGENT

LEVELS

Sets the volume of reagent in the reagent bottles to 100% full.

RESET STANDARD

LEVELS

Sets the volume of standard solution in the standard bottle to 100% full.

RESET CLEANING

SOLUTION LEVELS

Sets the volume of the cleaning solution in the cleaning solution bottle to 100%

full.

PRIME REAGENTS Starts the flow of all reagents through the tube and valve system. IMPORTANT:

prime the reagents each time the reagents are changed to remove bubbles

and push the new reagents through the system.

ENTER BLANK VALUE Sets the blank to a specific value printed on the R1 bottle label.

Grab sample options

The grab sample menu allows the user to analyze a specific sample or standard. Two options are

available:

• GRAB SAMPLE IN: This option is used to analyze an external sample or standard.

• GRAB SAMPLE OUT: This option is used to extract a sample directly from a sample line for

external analysis.

Measure a grab sample or standard

Use the grab sample funnel to measure grab samples taken from other areas in the system or to

measure a standard for a calibration verification.

1. Collect 250–500 mL of the sample or standard in a clean container.

2. Rinse the funnel outside of the unit with the collected sample.

3. Install the funnel again.

4. Select GRAB SAMPLE>GRAB SAMPLE IN.

5. Complete the instructions on the display. The result shows for 5 minutes.

Note: To see the result after 5 minutes, go to the Event Log.

Get a grab sample from the analyzer

Use the grab sample tube to manually dispense a grab sample from one of the sample sources for

external analysis.

The sample source is measured by the analyzer immediately after the sample is dispensed. The

value of the sample source and the job identification number for the grab sample are shown on the

display.

8

English

1. Select GRAB SAMPLE>GRAB SAMPLE OUT.

2. Complete the instructions on the display.

3. Put the grab sample out tube in a clean container. The grab sample tube is located in the lower

unit of the cabinet on the left side.

4. Push down on the spigot (upper left corner of the lower compartment) for the grab sample tube to

dispense a grab sample.

Set up the system

The configuration settings can be changed in the SETUP SYSTEM menu or in the analyzer setup.

Refer to Start the analyzer setup on page 6.

1. Select SETUP SYSTEM.

2. Push menu and select SETUP SYSTEM.

3. Select an option.

Option Description

MEAS MODE Changes the mode of the measurement cycle. Options: interval or continuous

(default). The continuous mode measures approximately every 9 minutes.

EDIT INTERVAL

(conditional)

Changes the interval time when MEAS MODE is set to interval. Options:

10–240 minutes (default = 15 minutes).

MEAS UNITS Changes the measurement units that are shown on the display and in the data

log. Options: ppb (default), ppm, mg/L, µg/L.

SIGNAL AVERAGE Selects the number of measurements used to calculate an average measurement

(1–5). This reduces variability in measurements (default = 1, no averaging).

EDIT ANALYZER

NAME

Changes the name that is shown on the top of the measurement screen

(maximum of 16 characters).

EDIT CHANNEL NAME Changes the name of the sample source that is shown on the measurement

screen (maximum of 10 characters).

CONFIGURE

SEQUENCER (optional)

Starts or stops measurements for individual sample sources. Sets the

measurement order of the sample sources when there is more than one sample

source.

SAMPLE MISSING Sets the operation that occurs if no sample is detected. Options: ON DELAY

(default) or OFF DELAY. ON DELAY: the instrument waits the remainder of the

measurement cycle, then goes to the next sample in the sequence. OFF DELAY:

the instrument waits 10 seconds, then goes to the next sample in the sequence.

SET DATE & TIME Sets the analyzer time and date.

DISPLAY SETUP Changes the language. Adjusts the order measurements are shown. Adjusts the

display contrast settings.

DISABLE REMINDERS Stops scheduled maintenance alerts for individual components. Options: tubing,

stir bar, colorimeter cell, air filter, stir motor, air relief valve, pinch valve, air

compressor, reagent valves, sample valves, standard valves, colorimeter LED, fan

filter, air check valve.

MANAGE DEVICES Installs or removes input modules. Refer to Manage devices on page 10 for

more information.

INSTRUMENT

INFORMATION

Shows the analyzer information. Refer to View instrument information

on page 16.

CALCULATION Set up variables, parameters, units and formulas for the analyzer. Refer to Set up

the calculation on page 10.

SETUP OUTPUTS Selects and configures the 4–20 mA setup, the relay setup and the error hold

mode. Refer to Configure the outputs on page 11 for more information.

English 9

Option Description

SETUP NETWORK

(conditional)

Shows only if a network card is installed. The network card support is for Modbus,

Profibus and HART.

SECURITY SETUP Enables or disables the pass code (default = HACH55).

AIR PURGE Enables the air purge for use with an external air supply. Options: on or off

(default). Off: an external air supply is not used. The vent fan is enabled and the

air filter is installed. On: an external air supply is connected to the instrument. The

vent fan is disabled. The air filter is replaced with a fan filter plug. To use this

feature, make sure that the fan filter plug is installed. Refer to the documentation

that is supplied with the air purge kit.

RESET DEFAULTS Sets the configuration to the factory defaults.

Manage devices

Install or remove input modules.

1. Push menu and select MANAGE DEVICES.

2. Select an option.

Option Description

SCAN FOR DEVICES The system shows the connected devices.

Note: If no device is connected, the system returns to the main measurement

screen.

DELETE DEVICE Removes the device when the device is no longer connected.

Set up the calculation

Set up variables, parameters, units and formulas for the analyzer.

1. Push menu and select CALCULATION.

2. Select an option.

Option Description

SET VARIABLE X Selects the sensor referring to the variable X.

SET PARAMETER X Selects the parameter referring to the variable X.

SET VARIABLE Y Selects the sensor referring to the variable Y.

SET PARAMETER Y Selects the parameter referring to the variable Y.

SET FORMULA Selects the calculation formula to complete. Options: None, X-Y, X+Y, X/Y, [X/Y]%, [X

+Y]/2, X*Y, [X-Y]%/X

DISPLAY FORMAT Selects the number of decimal places shown in a calculation result. Options: Auto,

XXXXX, XXXX.X, XXX.XX, XX.XXX, X.XXXX

SET UNITS Enters the unit name (maximum of 5 characters).

SET PARAMETER Enters the measurement name (maximum of 5 characters).

10 English

Configure the outputs

4–20 mA module setup

1. Push menu and select SETUP SYSTEM>SETUP OUTPUTS>4–20mA SETUP.

2. Select the OUTPUT.

3. Select an option.

Option Description

ACTIVATION The menu list items change with the selected function. Refer to 4–20 mA activation

options on page 11 for more information.

SELECT SOURCE Select the output. Options: None if the output is not configured, the analyzer name or

calculation if a calculation formula has been configured. Refer to Set up the calculation

on page 10.

SET PARAMETER Select the measurement channel from the list.

SET FUNCTION Select a function. Further options will vary depending on which function is chosen.

LINEAR CONTROL—Signal is linearly dependent on the process value. PID CONTROL

—Signal works as a PID (Proportional, Integral, Derivative) controller. LOGARITHMIC—

Signal is represented logarithmically within the process variable range. BILINEAR—

Signal is represented as two linear segments within the process variable range.

SET TRANSFER If TRANSFER is or will be selected as the ERROR HOLD MODE, select SET

TRANSFER and enter the transfer value. Range: 3.0 to 23.0 mA (default = 4.000). Refer

to Set the error hold mode on page 14.

SET FILTER Enter the filter value. This is a time-average filter value of 0 to 120 seconds (default = 0).

SCALE 0mA/4mA Select the scale (0–20 mA or 4–20 mA).

4–20 mA activation options

1. Push menu and select SETUP SYSTEM>SETUP OUTPUTS>4–20mA SETUP.

2. Select the applicable OUTPUT.

3. Select SET FUNCTION>LINEAR CONTROL and then select the applicable options in the

ACTIVATION menu.

Option Description

SET LOW VALUE Sets the low endpoint of the process variable range.

SET HIGH VALUE Sets the high endpoint (upper value) of the process variable range.

4. Select SET FUNCTION>PID CONTROL and then select the applicable options in the

ACTIVATION menu.

Option Description

SET MODE AUTO—the signal is automatically controlled by the algorithm when the analyzer uses

proportional, integral and derivative inputs.

MANUAL—the signal is controlled by the user. To change the signal manually, change the

% value in MANUAL OUTPUT.

PHASE Selects the signal result when process changes occur.

DIRECT—signal increases as the process increases.

REVERSE—signal increases as the process decreases.

SET SETPOINT Sets the value for a control point in the process.

PROP BAND Sets the value for the difference between the measured signal and the necessary setpoint.

INTEGRAL Sets the period of time from the reagent injection point to the contact with the measuring

device.

English 11

Option Description

DERIVATIVE Sets a value that adjusts for vacillation of the process. The majority of applications can be

controlled without the use of the derivative setting.

TRANSIT TIME Sets the value to stop the PID control for a selected period of time when the sample moves

from the control pump to the measurement sensor.

5. Select SET FUNCTION>LOGARITHMIC and then select the applicable options in the

ACTIVATION menu.

Option Description

SET 50% VALUE Sets the value corresponding to 50% of the process variable range.

SET HIGH VALUE Sets the high endpoint (upper value) of the process variable range.

6. Select SET FUNCTION>BILINEAR and then select the applicable options in the ACTIVATION

menu.

Option Description

SET LOW VALUE Sets the low endpoint of the process variable range.

SET HIGH VALUE Sets the high endpoint (upper value) of the process variable range.

SET KNEE POINT VALUE Sets the value at which the process variable range divides into another linear

segment.

SET KNEE POINT CURRENT Sets the value of the current at the knee point value.

Relay setup

1. Push menu and select SETUP SYSTEM>SETUP OUTPUTS>RELAY SETUP.

2. Select the relay.

3. Select an option.

Option Description

ACTIVATION The menu list items change with the selected function. Refer to Relay activation options

on page 12 for more information.

SELECT SOURCE Selects the output. Options: None (if the relay is not configured), the analyzer name or

calculation (if a calculation formula has been configured). Refer to Set up the calculation

on page 10.

SET FUNCTION Selects a function. ALARM—The relay starts when the upper or lower alarm value is

triggered. FEEDER CONTROL—The relay shows if a process value is larger or falls

below a setpoint. EVENT CONTROL—The relay toggles if a process value reaches an

upper or lower limit. SCHEDULER—The relay switches at certain times independently of

any process value. WARNING—The relay shows warning and error conditions in

probes. PROCESS EVENT—The relay switches when the analyzer does a specified

operation.

SET TRANSFER Selects active or inactive.

FAIL SAFE Selects yes or no.

Relay activation options

1. Push menu and select SETUP SYSTEM>SETUP OUTPUTS>RELAY SETUP.

2. Select the applicable relay.

12

English

3. Select ALARM in the FUNCTION menu and then select the applicable options in the

ACTIVATION menu.

Option Description

LOW ALARM Sets the value to set the relay to on in response to the decreasing measured value. For

example, if the low alarm is set for 1.0 and the measured value drops to 0.9, the relay

starts.

HIGH ALARM Sets the value to set the relay to on in response to the increasing measured value. For

example, if the high alarm is set for 1.0 and the measured value increases to 1.1, the

relay starts.

LOW DEADBAND Sets the range where the relay stays on after the measured value increases above the

low alarm value. For example, if the low alarm is set for 1.0 and the low deadband is set

for 0.5, the relay stays on between 1.0 and 1.5. The default is 5% of the range.

HIGH DEADBAND Sets the range where the relay stays on after the measured value decreases below the

high alarm value. For example, if the high alarm is set for 4.0 and the high deadband is

set for 0.5, the relay stays on between 3.5 and 4.0. The default is 5% of the range.

OFF DELAY Sets a delay time (0–300 seconds) to set the relay off (default = 5 seconds).

ON DELAY Sets a delay time (0–300 seconds) to set the relay on (default = 5 seconds).

4. Select FEEDER CONTROL in the FUNCTION menu and then select the applicable options in the

ACTIVATION menu.

Option Description

PHASE Specifies the relay status if the process value is larger than the setpoint. HIGH (default)

—sets the relay to on when the process value is larger than the setpoint. LOW—sets

the relay to on when the process value falls below the setpoint.

SET SETPOINT Sets the process value for the relay to toggle between the high and low value (default =

10).

DEADBAND Sets a delay so that the relay will be stable as the process value converges to the

setpoint.

OVERFEED TIMER Sets the maximum amount of time to get to the process setpoint. When the time

expires and the relay does not show the setpoint, the relay is set to off. After an

overfeed alarm occurs, reset the timer manually.

OFF DELAY Sets a delay time to set the relay to off (default = 5 seconds).

ON DELAY Sets a delay time to set the relay to on (default = 5 seconds).

5. Select EVENT CONTROL in the FUNCTION menu and then select the applicable options in the

ACTIVATION menu.

Option Description

SET SETPOINT Sets the value to set the relay to on.

DEADBAND Sets a delay so that the relay will be stable as the process value converges to the setpoint.

OnMax TIMER Sets the maximum time the relay stays on (default = 0 min).

OffMax TIMER Sets the maximum time the relay stays off (default = 0 min).

OnMin TIMER Sets the time the relay stays on, independent from the measured value (default = 0 min).

OffMin TIMER Sets the time the relay stays off, independent from the measured value (default = 0 min).

6. Select SCHEDULER in the FUNCTION menu and then select the applicable options in the

ACTIVATION menu.

Option Description

HOLD OUTPUTS Holds or transfers outputs for the selected channels.

English 13

Option Description

RUN DAYS Selects the days the relay stays on. Options: Sunday, Monday, Tuesday, Wednesday,

Thursday, Friday, Saturday

START TIME Sets the start time.

INTERVAL Sets the time between activation cycles (default = 5 min).

DURATION Sets the period of time the relay is set to on (default = 30 sec).

OFF DELAY Sets the time for additional hold/output time after the relay is set to off.

7. Select WARNING in the FUNCTION menu and then select the applicable options in the

ACTIVATION menu.

Option Description

WARNING LEVEL Sets the level for the warning activation and starts applicable individual warnings.

8. Select PROCESS EVENT in the FUNCTION menu and then select the applicable options in the

ACTIVATION menu.

Note: More than one option can be selected.

Option Description

MEASURING 1 Closes relay during measurement cycle.

MEASURING 2 Closes relay during measurement cycle.

MEASURING 3 Closes relay during measurement cycle.

MEASURING 4 Closes relay during measurement cycle.

MEASURING 5 Closes relay during measurement cycle.

MEASURING 6 Closes relay during measurement cycle.

ZERO CAL Closes relay during ZERO CAL cycle.

SLOPE CAL Closes relay during SLOPE CAL cycle.

SHUTDOWN Closes relay when in SHUTDOWN mode.

STARTUP Closes relay during STARTUP cycle.

GRAB SAMPLE Closes relay during GRAB SAMPLE measurement.

MARK END OF MEASUR Closes relay for 1 second at the end of each measurement cycle.

Set the error hold mode

1. Push menu and select SETUP SYSTEM>SETUP OUTPUTS>ERROR HOLD MODE.

2. Select an option.

Option Description

HOLD OUTPUTS Holds the outputs at the last known value when communications are lost.

TRANSFER OUTPUTS Switches to the transfer mode when communications are lost. The outputs transfer

to a pre-defined value.

14 English

View data

The analyzer stores a maximum of 18,000 data points. After 18,000 data points are stored, the oldest

data points are overwritten with new data.

1. Select VIEW DATA.

2. Select an option.

Option Description

ANALYZER DATA Shows analyzer status information (refer to Table 2).

MEASUREMENT DATA Shows measurement information (refer to Table 3).

LOG DATA Selects the data log and/or the event log. DATA LOG—shows the measurement

values. Select start time, number of hours and/or number of readings. EVENT LOG

—shows all analyzer information (e.g. alarms, warnings, configuration changes,

and so on.). Select start time, number of hours and/or number of readings.

Table 2 Analyzer data

Element Definition

CELL TEMP Temperature of the colorimeter cell block heater (ideally 49.8 °C to 50.2 °C (121.64 °F

to 122.36 °F))

REAGENT TEMP Reagent temperature before it enters the colorimeter

AMBIENT TEMP Air temperature inside the electronics area

SAMPLE TEMP Sample pre-heater block temperature (typically 45 °C to 55 °C (113 °F to 131 °F) but

could reach 58 °C (136.4 °F))

AIR PRESS Reagent air pressure in the reagent bottles (ideally 3.95 to 4.10 psi)

LED DUTY CYCLE Depends on condition of colorimeter cell and age of analyzer (typically 7,200 to

40,000 counts)

HEATER DUTY CYCLE Percentage of time the colorimeter heater is on to maintain a constant 50 °C (122 °F)

SAMPLE FLOW Approximate sample flow into the colorimeter, measured during the flush cycle

SAMPLE PRESS 1 Sample pressure before the pre-heater block (ideally 2 to 4.5 psi depending on

incoming sample pressure)

SAMPLE PRESS 2 Sample pressure after the sample pre-heater, which is used to calculate the sample

flow. The sample pressure is almost zero when the flush is set to off and is

approximately 0.2 psi when the flush is on (depends on inlet pressure and flow).

REAGENT 1 Level of reagent remaining

REAGENT 2 Level of reagent remaining

REAGENT 3 Level of reagent remaining

STD SOLUTION Level of standard solution remaining

FAN SPEED The speed of the ventilation fan.

LEAK COUNTS Indication of possible fluid leaks (range 0 to 1023). A count of over 511 indicates a fluid

leak

Table 3 Measurement data

Element Definition

LAST MEAS CHANNEL Last channel measured.

LAST MEAS TIME Time of last measurement.

English 15

Table 3 Measurement data (continued)

Element Definition

LAST ABS Last absorbance reading.

LAST CONC Concentration of last measurement.

NEXT MEAS TIME Time the next measurement will be taken.

DARK Number of A/D counts measured when the LED is turned off.

REF Reference A/D count used to compensate for natural color and turbidity.

SAMPLE A/D counts measurement (after color development) used to determine the

concentration of the sample.

DARK STD DEV Standard deviation of dark counts out of 6 readings.

REF STD DEV Standard deviation of reference counts out of 6 readings.

SAMPLE STD DEV Standard deviation of sample counts out of 6 readings.

SAMPLE VOLUME Total sample flush volume through the colorimeter for the measurement cycle.

REAGENT 1 Calculated reagent delivery time to the sample based on temperature, pressure and

viscosity.

REAGENT 2 Calculated reagent delivery time to the sample based on temperature, pressure and

viscosity.

REAGENT 3 Calculated reagent delivery time to the sample based on temperature, pressure and

viscosity.

View instrument information

1. Select INSTRUMENT INFORMATION.

2. Select an option.

Option Description

ANALYZER INFO Shows the software information and serial number.

MODULE INFO (option is available when a

module is installed)

Shows the connected modules with software information

and serial number.

Set up LINK2SC

The LINK2SC procedure is a secure method for the data exchange between process probes,

analyzers and LINK2SC-compatible laboratory instruments. Use an SD memory card for the data

exchange. Refer to the LINK2SC documentation on http://www.hach.com for a detailed description of

the LINK2SC procedure.

1. Push menu and select LINK2SC.

2. Select an option.

Option Description

CREATE A NEW JOB Starts the grab sample operation for the measurement value exchange between the

analyzer and the laboratory.

JOB LIST Selects the job file to send the job to the laboratory or deletes the job. JOB TO LAB

—the analyzer data is sent to the SD card as a job file. ERASE JOB—deletes the

data.

JOB ID MIN Specifies the minimum value for the ID number range.

JOB ID MAX Specifies the maximum value for the ID number range.

16 English

Use an SD card

Use an SD memory card to update the software and firmware and to download the event and data

logs. The SD icon is visible in the upper status bar of the main measurement screen when a card is

installed. The manufacturer recommends to use an SD card with a minimum of 2 GB storage

capacity.

1. Install the SD card (refer to Figure 4 on page 6).

2. Select SD CARD SETUP from the MAIN MENU.

Note: The SD CARD SETUP option shows only when an SD card is installed.

3. Select an option.

Option Description

UPGRADE SOFTWARE

(conditional)

Shows when an the upgrade file is available on the SD card. Select the specific

device for the upgrade.

SAVE LOGS Selects the device for the download data and to save the logs for last day, last

week, last month or all.

MANAGE

CONFIGURATION

Saves and restores the backup settings, restore settings and/or transfer

settings between instruments.

WORK WITH DEVICES READ DEVICE FILES—selects the data for each device to save on the SD

card. Options: sensor diag, measurement data (curve data for a measurement

cycle), cal history, cal data and/or test script. WRITE DEVICE FILES—shows

when an upgrade file is available for a new measurement cycle script.

Update the firmware

Use an SD card with an upgrade file to update the firmware for the controller, sensor or network card.

The upgrade menu is shown only when the SD card contains an upgrade file.

1. Install the SD card into the SD card slot.

2. Select SD CARD SETUP from the MAIN MENU.

Note: The SD CARD SETUP option shows only when an SD card is installed.

3. Select UPGRADE SOFTWARE and confirm. Select the device and upgrade version, if applicable.

4. When the upgrade is complete, the display shows TRANSFER COMPLETE. Remove the SD

card.

5. Restart the instrument for the upgrade to take effect.

Calibration

N O T I C E

The manufacturer recommends calibration of the analyzer after 1 day of operation to allow all system components

to stabilize.

The automatic calibration uses the installed known standard to calibrate the analyzer. Calibration can

be done manually or scheduled to occur automatically. Use the calibration menu to view calibration

data, start or cancel the auto calibration, override the auto cal settings, calibrate manually or to reset

to the default calibration.

1. Push cal to display the calibration menu.

Option Description

START MANUAL CAL Refer to Start a calibration manually on page 18.

SET AUTO CALIBRATION Refer to Schedule automatic calibrations on page 18.

English 17

Option Description

CALIBRATION DATA Displays data from the last calibration and the due date and time of the next

scheduled calibration.

OVERRIDE CALIBRATION Enter new slope and/or zero value (reagent blank). When OVERRIDE

CALIBRATION is selected, the automatic calibration is disabled for the selected

option.

OUTPUT CALIBRATION Select a 4-20 mA output and enter the output values to be sent.

RESET DEFAULT CAL Reset calibration data to default values and disables automatic calibration. On

completion, perform a new calibration.

Schedule automatic calibrations

1. Push cal, then select SET AUTO CALIBRATION.

2. Select ACTIVATE AUTO CAL>YES.

3. Select STD SOLUTION and enter the standard value in ppb.

4. Select a schedule option for calibration.

Option Description

TIME BASE Sets the interval between calibrations. Options: DAYS or HOURS.

WEEK DAY Selects the day or days of the week for calibration when TIME BASE is set to DAY.

TIME Sets the time of day for calibration when the TIME BASE is set to DAY.

SET INTERVAL Sets the interval between automatic calibrations in hours when the TIME BASE is set to

HOURS .

Start a calibration manually

1. Push cal, then select START MANUAL CAL.

2. The type of calibration is displayed. Push enter to start the calibration.

3. The measurement status is displayed. Select YES to interrupt the current measurement cycle and

start the calibration immediately. Select NO to wait until the current measurement cycle has

completed before the calibration starts.

4. Complete the instructions on the display.

18

English

Table des matières

Interface utilisateur et navigation à la page 19 Configurer les sorties à la page 27

Mise en marche à la page 22 Affichage des données à la page 31

Configurer les réactifs et les étalons à la page 24 Utiliser une carte SD à la page 33

Mesurer un échantillon ponctuel ou un étalon

à la page 24

Etalonnage à la page 34

Configurer le système à la page 25

Consignes de sécurité

Reportez-vous au manuel d'utilisation et d'installation pour connaître les consignes de sécurité

générales, les descriptions des risques et les descriptions des étiquettes de mise en garde.

Interface utilisateur et navigation

Description du clavier

Consultez Figure 1 pour obtenir une description du clavier et des informations de parcours des

menus.

Figure 1 Description du clavier

1 ECRAN 6 Diag (Diagramme) : permet d'accéder au MENU

DIAG/TEST

2 Touches de navigation DROITE/GAUCHE :

permettent de basculer entre les écrans de mesure,

de sélectionner des options et de parcourir les

champs de saisie de données

7 Cal (Etalonnage) : permet d'accéder au MENU

D'ETALONNAGE

3 Touches de navigation HAUT/BAS : permettent de

parcourir les menus et les canaux de mesure, et de

saisir des nombres et des lettres

8 Back (Retour) : permet de revenir au menu

mesure principal

9 Menu : permet de sélectionner des options dans le

menu principal de l'analyseur

5 Enter (Entrée) : permet de confirmer et d'ouvrir des

sous-menus

Description de l'affichage

Reportez-vous à la Figure 2 pour obtenir une description de l'écran de mesure. Reportez-vous à la

Figure 3 pour obtenir une description de l'écran d'état du système.

Français

19

Figure 2 Ecran de mesure

1 Accueil (écran de mesure principal) 6 Relais (seconde icône affichée lorsqu'un relais

supplémentaire est installé)

2 Canal de mesure 7 Paramètre

3 Activité (pendant une mesure ou un processus

d'étalonnage)

8 Valeur de mesure

4 Rappel (pour une tâche de maintenance) 9 Nom du canal

5 Carte SD (affichée lorsqu'une carte SD est insérée) 10 Nom de l'analyseur

Figure 3 Ecran d'état du système

1 Informations sur l'état de l'étalonnage 3 Réactif (Rx) et étalons (Sx, Standard) avec

indicateurs de niveau de liquide (%)

1

2 Barre d'indication de service PROGNOSYS 4 Barre d'indication de qualité des mesures

PROGNOSYS

Barres d'indication PROGNOSYS

La barre d'indication de service indique le nombre de jours précédant la prochaine intervention

nécessaire. La barre d'indication de la qualité des mesures indique l'intégrité de mesure globale de

l'analyseur mesurée sur une échelle de 0 à 100.

Couleur Signification de la couleur pour la barre

d'indication de service

Signification de la couleur pour la barre d'indication

de la qualité des mesures

Vert Il reste au moins 45 jours avant que la

prochaine intervention soit nécessaire.

Le système est en bon état de fonctionnement et le

pourcentage d'intégrité est supérieur à 75 %.

Jaune Au moins une intervention sera nécessaire

dans les 10 à 45 jours.

Le système doit être surveillé afin d'éviter une panne à

l'avenir. Le pourcentage d'intégrité est compris entre

50 et 75 %.

Rouge Une ou plusieurs interventions seront

nécessaires dans les 10 prochains jours.

Le système réclame une attention immédiate. Le

pourcentage d'intégrité est inférieur à 50 %.

1

Le nombre de bouteilles indiqué à l'écran dépend du nombre de bouteilles installées.

20 Français

ページを読み込んでいます...

Hach 500sc SiO2 Operations

関連論文

その他の書類