Hach DR300 ユーザーマニュアル

DOC022.97.90639

DR300

12/2018, Edition 1

User Manual

Manual del usuario

Manuel de l'utilisateur

Manual do Usuário

用户手册

使用手冊

取扱説明書

사용

설명서

คู่มือผู้ใช้

English.................................................................................................. 3

Español............................................................................................... 25

Français.............................................................................................. 48

Português............................................................................................ 73

中文 ..................................................................................................... 96

中文 ................................................................................................... 116

日本語 ............................................................................................... 134

한글 ................................................................................................... 156

ไทย..................................................................................................... 178

2

Table of contents

Product components on page 6 Calibration on page 15

Install the batteries on page 7 Maintenance on page 20

User interface and navigation

on page 8

Troubleshooting on page 21

Do a test on page 11 Replacement parts and accessories

on page 24

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions (W x H x D) 6.9 x 15.7 x 3.4 cm (2.7 x 6.2 x 1.3 in.)

Enclosure IP67, waterproof at 1 m (3.3 ft) for 30 minutes when

battery compartment is closed and locked.

Light source Light emitting diode (LED)

Detector Silicon photodiode

Display LCD with backlight

Weight 0.25 kg (0.55 lb)

Power requirements 4 AAA batteries; approximate life of 5000 tests (use of

backlight decreases this number)

Rechargeable batteries are not recommended.

Operating environment 0 to 50 °C (32 to 122 °F), 0 to 90% relative humidity

non-condensing

Storage temperature –20 to 55 °C (–4 to 131 °F), 0 to 80% relative humidity

non-condensing

Wavelength Fixed wavelength ±2 nm, different for each model

Filter bandwidth 15 nm

Absorbance range 0 to 2.5 Abs

Sample cell 25 mm (10 mL) and 1 cm (10 mL)

Data storage Last 50 measurements

English 3

Specification Details

Bluetooth

®

1

Bluetooth

®

is on when the optional Hach

Communication Dongle is installed.

Certifications CE

Warranty 1 year (EU: 2 years)

General information

In no event will the manufacturer be liable for direct, indirect, special,

incidental or consequential damages resulting from any defect or

omission in this manual. The manufacturer reserves the right to make

changes in this manual and the products it describes at any time,

without notice or obligation. Revised editions are found on the

manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or

misuse of this product including, without limitation, direct, incidental and

consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical

application risks and install appropriate mechanisms to protect processes

during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or

operating this equipment. Pay attention to all danger and caution

statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not

impaired. Do not use or install this equipment in any manner other than

that specified in this manual.

1

The Bluetooth

®

word mark and logos are registered trademarks

owned by the Bluetooth SIG, Inc. and any use of such marks by

HACH is under license.

4 English

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided,

will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided,

could result in death or serious injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate

injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the

instrument. Information that requires special emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or

damage to the instrument could occur if not observed. A symbol on the

instrument is referenced in the manual with a precautionary statement.

This symbol, if noted on the instrument, references the instruction

manual for operation and/or safety information.

Electrical equipment marked with this symbol may not be disposed

of in European domestic or public disposal systems. Return old or

end-of-life equipment to the manufacturer for disposal at no charge

to the user.

Certification

Canadian Radio Interference-Causing Equipment Regulation,

IECS-003, Class B:

Supporting test records reside with the manufacturer.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

English 5

Cet appareil numérique de classe B répond à toutes les exigences de

la réglementation canadienne sur les équipements provoquant des

interférences.

FCC Part 15, Class "B" Limits

Supporting test records reside with the manufacturer. The device

complies with Part 15 of the FCC Rules. Operation is subject to the

following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications to this equipment not expressly approved by

the party responsible for compliance could void the user's authority to

operate the equipment. This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case

the user will be required to correct the interference at their expense.

The following techniques can be used to reduce interference problems:

1. Move the equipment away from the device receiving the

interference.

2. Reposition the receiving antenna for the device receiving the

interference.

3. Try combinations of the above.

Product overview

This instrument is a portable filter photometer used for testing water.

Note: This instrument has not been evaluated to measure chlorine and

chloramines in medical applications in the United States.

Product components

Make sure that all components have been received. Refer to Figure 1.

If any items are missing or damaged, contact the manufacturer or a

6 English

sales representative immediately. Figure 1 is an example and shows

the parts supplied with LPV445.99.00110. Other instruments come with

different components.

Figure 1 Product components

1 DR300 5 Storage case

2 AAA alkaline batteries 6 Reagents

3 Sample cells, 25 mm (10 mL),

glass

7 Hach Communication Dongle

(optional, supplied separately)

4 Sample cells, 1 cm (10 mL), plastic

Install the batteries

W A R N I N G

Explosion hazard. Incorrect battery installation can cause the release

of explosive gases. Be sure that the batteries are of the same

approved chemical type and are inserted in the correct orientation.

Do not mix new and used batteries.

Refer to Figure 2 to install the batteries. Then, push to set the

instrument to on.

English 7

Figure 2 Install the batteries

1 Coin 3 Plastic insert for dongle

2

2 Battery cover

User interface and navigation

Keypad description

Figure 3 shows the keypad and gives the key functions.

2

Only remove the plastic insert to install the Hach Communication

Dongle. Refer to the installation instructions supplied with the

dongle.

8 English

Figure 3 Keypad

1 Range key: Selects the

measurement range (e.g., LR or

HR).

Push and hold for 3 seconds to

enter or exit menu mode.

In menu mode, scrolls up or

increases the value of the selected

digit.

4 Backlight key: Sets the backlight

to on and off.

In menu mode, scrolls down or

decreases the value of the selected

digit.

2 Zero key: Sets the zero value

before a measurement.

In menu mode, goes back one

menu level or moves the cursor to

the previous digit.

5 Read key: Starts a sample

measurement.

In menu mode, selects the menu

option shown or moves the cursor

to the next digit.

3 Power key: Sets the power to on

and off.

Push and hold for 5 seconds to

reset the instrument. The

calibration is not deleted.

English 9

Display description

Figure 4 shows the values and icons shown on the display.

Figure 4 Display

1 Numeric display: Measured value

or menu options

5 Battery icon: Battery power level.

Flashes when the battery power

level is low.

2 Range icon: Points to the selected

measurement range

6 Parameter and measurement

ranges

3 Measurement ranges or

parameters

7 Calibration adjusted icon: The

factory default calibration was

adjusted or a user-entered

calibration curve was entered.

4 Bluetooth

®

icon: Bluetooth

®

is

on

3

.

Set the time

Set the time (24-hour format).

1. Push and hold for 3 seconds to enter menu mode.

The time shows (or 00:00).

2. Push to set the time.

3. Push the or to change the number that flashes. Push to go

to the next digit. Push to go to the previous digit.

3

Shows when the Hach Communication Dongle is installed.

10 English

Do a test

D A N G E R

Chemical or biological hazards. If this instrument is used to monitor a

treatment process and/or chemical feed system for which there are

regulatory limits and monitoring requirements related to public health,

public safety, food or beverage manufacture or processing, it is the

responsibility of the user of this instrument to know and abide by any

applicable regulation and to have sufficient and appropriate

mechanisms in place for compliance with applicable regulations in

the event of malfunction of the instrument.

D A N G E R

Chemical exposure hazard. Obey laboratory safety procedures and

wear all of the personal protective equipment appropriate to the

chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Chemical exposure hazard. Dispose of chemicals and wastes in

accordance with local, regional and national regulations.

The generic steps to do a test follow.

To do a test for a specific parameter (e.g., chlorine), download the test

procedure from the manufacturer's website. Refer to Download a test

procedure on page 14.

1. Push to select the applicable measurement range (e.g., LR or

HR).

2. Prepare the blank. Refer to the test procedure.

3. Clean the sample cell with a no-lint cloth.

4. Insert the blank sample cell into the cell holder. Make sure to install

the blank sample cell in the correct and consistent orientation so

that the results are more repeatable and precise. Refer to Figure 5.

5. Install the instrument cap over the cell holder. Refer to Figure 6.

6. Push to set the instrument zero.

English 11

7. Remove the blank sample cell.

8. Prepare the sample. Refer to the test procedure.

9. Clean the sample cell with a no-lint cloth.

10. Insert the sample cell into the cell holder. Make sure to install the

sample cell in the correct and consistent orientation so that the

results are more repeatable and precise. Refer to Figure 5.

11. Install the instrument cap over the cell holder. Refer to Figure 6.

12. Push . The display shows the results in concentration units or

absorbance.

Note: The result flashes if the result is less or more than the instrument

range.

13. Remove the sample cell from the cell holder.

14. Immediately empty and rinse the sample cell. Rinse the sample cell

and cap three times with deionized water (or distilled water).

Note: As an alternative, use tap water to rinse the sample cell if the samples

measured have a higher concentration than the tap water.

12 English

Figure 5 Sample cell orientation

1 Orientation mark

4

2 Sample cell, 25-mm

(10 mL), glass

5

3 Sample cell, 1-cm

(10 mL), plastic

6

4

Some variants of the instrument have sample cells without an

orientation mark.

5

Use the glass sample cell for low-range chlorine tests.

6

Use the plastic sample cell for high-range chlorine tests.

English 13

Figure 6 Install the instrument cap over the cell holder

Download a test procedure

1. Go to http://www.hach.com.

2. Enter "DR300" in the Search box.

3. Select the applicable instrument from the list.

4. Click the Downloads tab.

5. Scroll down to "Methods/Procedures".

6. Click the link for the applicable test procedure to download it.

14 English

Show measurements

Note: The instrument saves a maximum of 50 measurements. After

50 measurements are done, new measurements replace the oldest

measurements.

1. Push and hold for 3 seconds.

2. Push until "rCL" (recall) shows, then push .

"– 01 –" shows. Measurement 01 is the last measurement done.

3. Push to scroll forward.

The measurement number is followed by the measurement value

and then the time.

4. To go to a measurement number, push until a measurement

number shows, then push or .

Note: Measurements cannot be deleted.

5. Push and hold for 3 seconds to go back to measurement mode.

Calibration

This instrument is calibrated at the factory. No user calibration is

necessary.

Standard calibration adjust

Use the standard calibration adjust (SCA) option when a calibration

must be adjusted to meet regulatory requirements. The factory

calibration is adjusted slightly with the standard calibration adjust

(SCA) option so that the instrument shows the expected value of the

standard solution. The adjusted calibration is then used for all test

results. This adjustment can increase the test accuracy when there are

slight variations in the reagents or instruments.

Note: For instruments with factory-calibrated ranges or methods, the standard

calibration adjust (SCA) feature is disabled when a user-entered calibration is

entered into the instrument. To set SCA back to on, set the instrument to the

factory default calibration. Refer to Set to the factory default calibration

on page 20.

English 15

Do a standard calibration adjust

1. Complete the test procedure for the range to calibrate. For the

sample, use the standard solution concentration given in the test

procedure documentation.

Note: If a standard solution concentration is not given in the test procedure

documentation, a different known standard can be used.

2. When the test procedure is completed, push and hold for

3 seconds.

3. Push until “SCA” shows, then push .

The display shows the standard calibration adjust value.

4. If a different known standard is used, enter the value of the

standard:

a. Push until "Edit" shows, then push .

b. Enter the value of the standard.

Push the or to change the number that flashes. Push to

go to the next digit. Push to go to the previous digit.

5. Push to add the standard calibration adjust value to the factory

calibration curve.

Set the standard calibration adjust to off

To use the factory default calibration again, set standard calibration

adjust (SCA) to off.

1. Push and hold for 3 seconds to enter menu mode.

2. Push until "SCA" shows, then push .

3. Push until "OFF" shows, then push .

Note: To set the SCA function to on again, do a standard calibration adjust.

User-entered calibration curve

This instrument accepts a user-prepared calibration curve. The

calibration curve can be from 0 to 2.5 absorbance. Make sure that the

calibration curve includes standard values that are less and more than

the range of interest.

The instrument range will be the same as the calibration range. For

example, when the standards that are used are 1.00, 2.00 and 4.00.

The instrument range is 1.00 to 4.00.

16 English

There are two options to enter a user calibration curve:

• Enter a calibration curve with standards—The standard solution

values are entered with the keypad and the absorbance values are

measured.

• Enter a calibration curve with the keypad—The standard solution

values and absorbance values are entered with the keypad.

Note: If the instrument is set to off or the instrument power is removed before a

user-entered calibration curve is completed, the calibration curve is not saved.

The instrument automatically switches off in user-entered calibration entry mode

after 60 minutes of no activity. User-entered calibrations are completed when the

user goes out of calibration (cal) mode or edit mode.

Enter a calibration curve with standards

W A R N I N G

Chemical exposure hazard. Obey laboratory safety procedures and

wear all of the personal protective equipment appropriate to the

chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Chemical exposure hazard. Dispose of chemicals and wastes in

accordance with local, regional and national regulations.

Note: As an alternative, deionized water can be used for the blank unless the

sample is significantly more turbid or has more color than deionized water.

1. Push to set the instrument to the range to calibrate (e.g., LR or

HR).

2. Prepare the blank. Refer to the test procedure.

3. Clean the sample cell with a no-lint cloth.

4. Set the instrument to zero.

a. Insert the blank sample cell in the cell holder.

b. Install the instrument cap over the cell holder.

English 17

c. Push . The display shows “- - - -”, then “0.00”.

5. Push and hold for 3 seconds to enter menu mode.

6. Push until "USEr" shows, then push .

7. Push until "CAL" shows, then push .

8. When "S0" shows on the display, push .

9. Enter 00.00 (or 000.0) for the blank value.

Push the or to change the number that flashes. Push to go

to the next digit. Push to go to the previous digit.

10. When “A0” shows on the display, push to measure the

absorbance of the blank.

The display shows the absorbance value for "S0".

11. Remove the sample cell from the cell holder.

12. Prepare the sample. Refer to the test procedure. For the sample,

use the standard solution concentration given in the test procedure

documentation.

13. Clean the sample cell with a no-lint cloth.

14. Push to show "S1" (or "Add"), then push .

15. Enter the concentration value of the first calibration standard, then

push .

16. When "A1" shows on the display, do the steps that follow to

measure the absorbance:

a. Insert the reacted standard sample cell in the cell holder.

b. Install the instrument cap over the cell holder.

c. Push . The display shows the absorbance value for "S1".

17. The calibration is completed with two calibration points. If additional

standards are necessary for calibration:

Do steps 11 and 16 again to measure more calibration standards.

18. Remove the sample cell from the cell holder.

18 English

19. Immediately empty and rinse the sample cell. Rinse the sample cell

and cap three times with deionized water (or distilled water).

Note: As an alternative, tap water can be used to rinse the sample cell if the

concentration of the parameter in the tap water is less than the samples

measured.

20. Push and hold for 3 seconds to go back to measurement mode.

Enter a calibration curve with the keypad

At least two data pairs are necessary to enter a user-prepared

calibration curve. A concentration value and the absorbance value for

the given concentration is necessary for each data pair. A maximum of

10 data pairs can be entered.

1. Push to set the instrument to the range to calibrate (e.g., LR or

HR).

2. Push and hold for 3 seconds to enter menu mode.

3. Push until "USEr" shows, then push .

4. Push until "Edit" shows, then push .

5. When "S0" shows on the display, push .

6. Enter the first data pair.

The first data pair is S0 (concentration value) and A0 (absorbance

value).

• Push or to change the number that flashes.

• Push to go to the next digit.

• Push to go to the previous digit.

7. Do steps 5 and 6 again to enter the second data pair (S1 and A1).

8. The calibration is completed with two data pairs. If additional data

pairs are necessary for calibration:

a. When “Add” shows, push .

b. Do steps 5 and 6 again to enter more data pairs.

9. Push and hold for 3 seconds to go back to measurement mode.

English 19

Set to the factory default calibration

To remove a user-entered calibration curve from the instrument and

use the factory calibration, do the steps that follow:

1. Push and hold for 3 seconds to enter menu mode.

2. Push until "USEr" shows, then push .

3. Push until "dFL" (default) shows, then push .

Maintenance

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks

described in this section of the document.

N O T I C E

Do not disassemble the instrument for maintenance. If the internal components

must be cleaned or repaired, contact the manufacturer.

Clean the instrument

Clean the exterior of the instrument with a moist cloth and a mild soap

solution and then wipe the instrument dry as necessary.

Clean the sample cells

C A U T I O N

Chemical exposure hazard. Obey laboratory safety procedures and

wear all of the personal protective equipment appropriate to the

chemicals that are handled. Refer to the current safety data sheets

(MSDS/SDS) for safety protocols.

C A U T I O N

Chemical exposure hazard. Dispose of chemicals and wastes in

accordance with local, regional and national regulations.

Most laboratory detergents are used at recommended concentrations.

Neutral detergents, such as Liquinox, are safer to use when regular

20 English

ページを読み込んでいます...

Hach DR300 ユーザーマニュアル

関連論文