Dancing Wings Hobby TCG 14 Basswood Training Airplane ユーザーマニュアル
- カテゴリー
- リモコンのおもちゃ
- タイプ
- ユーザーマニュアル
推荐配置
Suggested Equipment
推荐马达: 2815-2820 800-900KV
推荐桨叶: 12*6
推荐电调: 60A
推荐舵机: 17gx6pcs
推荐电池 4S 2200-2800mAh
推荐6通道以上接收机
飞行参数
Specification
翼展:1400mm
机长:1187mm
起飞重量: 1.5-1.6kg
Wingspan: 1400mm
Fuselage Length: 1187mm
Flying Weight: 1.5-1.6kg
Suggested Motor: 2815-2820 800-900KV
Suggested Propeller: 12*6
Suggested ESC: 60A
Suggested Servo: 17gx6pcs
Suggested Battery: 4S 2200-2800mAh
Radio:more than 6CH
Balsawood Training Airplane
● 这个产品不是玩具，而是一个复杂的具有难度的飞行器。您和您身边人的安全取决于您如何操作它，您需要了解相关知识，并谨慎操作。禁止
没有成人陪伴的儿童独自操作该设备。不适合14岁以下人群使用。再次强调，这不是一个玩具。
● This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends
on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be
accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A
TOY.
● 不要在机场，军事基地，居民区或其他任何受限制的地方飞行。
● Do not fly around some restricted location like airports, military bases, residential areas, etc.
● 您需要对发射机进行距离检查，以确保没有收到任何干扰。
● You will need to range check the transmitter to be sure you are not experiencing any interference.
● 始终保持先打开发射机后打开接收机，先关闭接收机后关闭发射机的步骤。
● Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
● 如果您是初学者，建议您在有经验玩家的协助下调试和飞行。
● If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from
advanced expert fliers.
● 请将相关物品放置在孩子们够不到的地方
● Keep relevant items out of reach of children.
● 这个设备的设计已经超过我们正常使用所需要刚性要求，但若您需要以超出我们推荐的动力飞行时，请合理控制动作幅度并适当增加机体强度。
● This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform
any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body
strength.
● 您的设备中可能包括一些玻纤和碳纤雕刻的部件，这些纤维部件所带的粉尘可能会引起眼睛，皮肤的不适，请您在需要的时候带上护目镜或者防尘服。
● This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the
goggles or dust-proof clothes when needed.
● 因航空运输安全管制，您收到的产品可能没有清单中出现过的胶水，请您理解无法发送胶水给您的原因。您可以在当地文具店很方便的购买到您所需要
的胶水。
● Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the
glue you need at your local stationery store.
注意事项
SAFETY PRECAUTIONS
● 安装舵机前，请先将舵机通电让舵机中心点回中，以便能更好的调试舵面。
● Check/adjust servo centering, in order to adjust the control surface better.
● 初次启动电机，您需要确认电机旋转的方向以适配您的机型。
● Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
● 请将重心（CG）调整至说明书所述位置并尽量靠近。如果有需要，您可以增加机头或者机尾的重量，以确保机体有更好的飞行姿态。
● Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to the nose or tail
to ensure the best flight performance.
● 检查机身内部，确保所有设备正常连接；检查机身表面，包括但是不限于蒙皮，固定螺丝，舱盖，座舱罩等位置。
● Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the heat-shrink
covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
● 在飞行前，请检查您电池情况，若有低电压，电池损坏等情况，请您停止操作并马上更换电池。
● Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found low voltage
or damage to battery.
● 机身内部设备连接的方式，会和您的收发设备有关，在一些功能更多的收发设备上，您可以通过设置简化机身内部设备的连接。详细
请查看您的收发设备以确认是否满足您需要的功能。
● The way the internal devices of the fuselage are connected will be related to your transmitter-receiver device. For those
transmitter-receiver devices with more functions, you can simplify the connection of the internal devices of the fuselage.
Check your device for details to see if it meets the features you need.
● 动力设备和收发设备第一次配对时，可能需要设置油门最大行程，请您自行设置。
● When the power system and transmitter-receiver device are paired for the first time, you may need to set the maximum
stroke of the throttle. Please set it yourself.
飞行前的建议
PRE-FLIGHT CHECKS
http://www.dwhobby.com/
工具
Tools Needed
TCG14
散件 KIT
配件图仅做参考用，您收到的实
物可能因为修改/优化的原因导
致与图片有略有不同。
Photos shown here just for
reference, the product you
received maybe slightly differ
from the photos due to
continuous improvement on
products.
1
01
机翼组装
Assemble the Wing
A
B1
B2
B3
C1
C2
C3
C4
C5
D1
E1
E2
F
G
H I
J1
J2
K
L
M
D3
D2
A:机身
B1:机翼
B2:副翼
B3:襟翼
C1:水平尾翼
C2:升降舵
C3:方向舵
C5:升降舵连接钢丝
D1:起落架
D2:机轮
D3:尾轮组
E1/E2:机翼连接碳杆
F:连杆
G:机轮罩
H:油动舵机架
I:魔术胶带
J1-J2:机翼固定件
K:纸合页
L:舵角
M:快装接头
01-1 01-2
在副翼，和襟翼的预留槽里插入纸合页，用少量CA胶水粘固。
Plug paper hinge into the pre-cutted slot of aileron and flap
wing.Stick it with a little CA glue.
把粘好纸合页的副翼襟翼插入机翼的预留槽，调整合适间隙。
Plug the aileron and flap wing into the pre-cutted slot of wings,
adjust appropriate space.
B3
K
B3
B2
B1
01-3
在连接处点入少量CA胶粘合固定。
Fasten with a little CA glue on the joint.
用镊子挑出预埋的引导线。
Pick out the pre-embedded guiding wire with tweezers.
在机翼的背面用美工刀切开舵机的空位，和舵机线导出孔。
Cut the servo hole and servo wire's guiding hole with
knife on the back of wings.
01-4
提示：此处需要切开的孔，可以用手摸来确定孔位，也可对着灯光同过光线
来确定孔位。
Note:Touch the holes to confirm the correct hole position, or confirm
it at the bright light.
01-5
01-6
在安装机翼上舵机前，您的舵机可能需要接延长线。
Before installing servo of the wings, your servo may need to connect
extension line.
把最远端的引导线绑在舵机线上，然后拉另一端的引导线，让舵机线穿入机
翼内。
Bind the farthest guiding line on the servo line, then pull the other
end of the guiding line,let the servo line to penetrate into wings.
拉到中段时再绑上另一个
舵机的舵机线，继续拉动
引导线。
Bind another servo line
when you pull it in the
middle section,
continue to pull the
guiding line.
01-7
01-8
C4:垂直尾翼
M:Quick JointL:Control HornK:Paper HingeJ1-J2:Wing Fixed Parts I:Magic TapeH:Servo Frame for Gas Power
G:Wheels CoverF:Linkage RodE1/E2:Carbon Rod for Connecting WingsD3:Tail Wheel Combo
D2:WheelsD1:Landing GearC5:Steel Wire for Connecting ElevatorC4:Vertical Tail
C3:RudderC2:ElevatorC1:Horizontal TailB3:Flap WingB2:AileronB1:WingA:Fuselage
2
机翼连接件组装 Assemble the Wing Connector
一直拉引导线，直至两条舵机线从圆孔导出。
Keep pulling the guiding line, until the 2pcs servo lines leading-out
from the round hole.
参考舵机的螺丝位置，在机翼上钻出螺丝孔位，然后在孔里点入少量CA胶。
Refer to the position of servo's screw, drill the hole for the screw on
the wing, then put a little CA glue in the hole.
用螺丝固定住舵机。机翼上两个舵机相同方法安装。
Fasten the servo with screw.The same installation way for 2pcs servos
on the wing.
01-11
01-9
01-10
在舵机上安装舵臂，并安装连
杆，连杆Z型一端穿入舵臂。
Install the servo arm on the
servo, and mount the linkage
rod, plug the linkage rod's
Z-shape end into the servo
arm.
连杆垂直于机翼摆放，参考连
杆末端位置，在副翼上确定舵
角的位置。
Put the linkage rod be
perpendicular to the wing,
refer to the endmost position
of linkage rod,confirm the
servo horn's position on the
aileron.
注意：连杆安装在舵机左侧。
Note:Install the linkage rod
on the left of the servo.
在确定的位置上，钻螺丝孔，孔内点少量CA胶水，然后用螺丝固定舵角。
In the definite position, drill screw hole,put a little CA glue, then
fasten the servo horn with screw.
在舵角上安装快装接头，并锁定
连杆。
Install the quick joint on the
servo horn, and lock the
linkage rod.
使用时切开
Cut open
when using.
01-12
01-14
01-15
另一个舵机的连杆参照01-12至01-15步骤相同安装。
Refer to 01-12 to 01-15 steps, install another servo's linkage rod with
same way.
另边机翼参照01-1至01-15步骤相同安装。
Refer to 01-1 to 01-15 steps, install another wing with
same way.
01-16
01-17
在机翼的中段插入碳管，并把完成的两部分机翼对插在一起。
Plug carbon tube into the middle of the wing, and insert the finished
two wings into each other.
在机翼的前端预留孔内插入碳管锁定销，用CA胶粘固。
Plug the carbon tube's locking tip into the reserved hole of the wing's
front end, fasten with CA glue.
01-13
01-18
02
垂直尾翼/水平尾翼/后尾轮安装
Vertical Tail/Horizontal Tail/
Rear-tail wheel Installation
L
F
M
E1
E2
E2
02-1
在升降舵的预留槽里插入纸合页，用少量CA胶水粘固。
Plug paper hinge into the pre-cutted slot of elevator, fasten with a
little CA glue.
K
02-2
把连接钢丝插入升降舵预留槽，然后查看两片舵面是否平直，如果不平，可
抽出钢丝调整，直到调整平直。
Plug the connecting steel wire into the pre-cutted slot of elevator,
then check the 2pcs rudder surface are straight and flat or not.
If not, you can draw out the steel wire and adjust it until the rudder
surface keep flat and straight.
C2
C2
C5
在调整好的升降舵连接钢丝处，用大量CA胶粘合牢固。
Use a lot of CA glue to fasten the position of elevator's connecting
steel wire which well-adjusted before.
把升降舵插入水平尾翼，在连接合页
处点入少量CA胶粘合。
Plug the elevator into the
horizontal tail, use a little CA glue
on the position of connecting
hinge.
02-4
02-3
C1
M2*10mm 自攻螺丝
M2*10mm Self-tapping screw
4*50mm碳管
4*50mm carbon tube
10*680mm 碳管
10*680mm carbon tube
02-8
3
03
起落架安装
Landing Gear Installation
02-5
在机身尾翼安装水平尾翼，用
螺丝锁定。
Install horizontal tail on the
tail wing of fuselage, lock
with screw.
M2*10mm自攻螺丝+垫片
M2*10mm self-tapping screw+spacer
在垂直尾翼的预留槽里插入纸合页，用少量CA胶水粘固。
Plug paper hinge into the pre-cutted slot of vertical tail wing, fasten
with a little CA glue.
把垂直尾翼插入机身尾部，调整与机身垂直后用CA胶水粘固。
Plug the vertical tail wing into the tail of fuselage,adjust it to be
perpendicular to fuselage and fasten with CA glue.
把钢丝连杆插入机身导管内，Z型一头在机身内，另一头从机身尾部导出。
Plug the steel wire linkage rod into the duct of fuselage,
put Z-shape end inside fuselage, another end leading-out from the
tail of fuselage.
安装机轮，用自锁螺母锁定。
Install wheels, fasten with
self-locking nut.
在起落架上安装螺丝杆，用2个
自锁螺母锁定。（如左图所示）
Install screw pole on landing
gear, fasten with 2pcs
self-locking nuts.(As shown
on the left)
02-13
02-7
02-9
02-10
把尾轮组件插入转向舵的预留槽内。
Plug the tail wheel parts into the pre-cutted slot of steering rudder.
用大量CA胶水粘固尾轮组件。
Fasten the tail wheel parts with a lot of CA glue.
把转向舵与垂直尾翼通过纸合页链接，纸合页连接处用少量CA胶粘合。
Connect steering rudder and vertical tail wing with paper hinge, stick
with a little CA glue on the joint of paper hinge.
用自攻螺丝把尾轮组件固定到飞机尾部（如上图）
Fasten the tail wheel parts on the tail of airplane with self-tapping
screw. (Like the one above)
M4*45 内六角螺丝+自锁螺母
M4*45 Hexagon screw +
Self-locking nut
自锁螺母
self-locking nut
03-1
03-2
03-3
把轮罩卡起落架与机轮之间，用自攻螺丝锁定机轮罩。两边机轮相同安装。
Install the mounted landing gear on the fuselage, fasten with screw.Use
same way to install another wheel cover.
02-11
02-12
02-14
在机身内安装舵机，连杆Z型头穿入舵臂，并把舵臂固定到舵机上。
Install servo in the fuselage, plug the z-shape end of linkage rod into
servo arm, and fasten the servo arm on the servo.
在转向舵上安装舵角，参考尾部连杆位置在舵面上确定位置，用自攻螺丝固
定住，连杆用快装接头固定在舵角上。
Install the servo horn on the steering rudder,refer to the position of
linkage rod in tail, confirm the position on rudder surface.
Fasten with self-tapping screw, fasten the linkage rod on the servo
horn with quick joint.
02-14
转向舵
Steering Rudder
升降舵
Elevator
背面
Back Side
在升降舵上安装舵角，参考尾部连杆位置在舵面上确定位置，用自攻螺丝固
定住，连杆用快装接头固定在舵角上。
Install the servo horn on the elevator,refer to the position of linkage
rod in tail, confirm the position on rudder surface.
Fasten with self-tapping screw, fasten the linkage rod on the servo
horn with quick joint.
背面
M2.5*8mm 自攻螺丝
M2*10mm 自攻螺丝
M2*10mm self-tapping screw
M2*10mm 自攻螺丝
M2*10mm self-tapping screw
M2*8mm 自攻螺丝
M2*8mm self-tapping screw
C4
C3
D3
L
M
Back Side
M2.5*8mm
self-tapping screw
K
4
03-4
把安装好机轮的起落架安装到机身上，用螺丝固定。
Install the mounted landing gear on the fuselage, fasten with screw.
04
Motor/Propeller/ESC Installation
马达/桨叶/电调安装
08
Power System Installation and Adjustment
电子设备安装调试
07
Check and Adjustment
检查与调试
05
Assemble the horizontal and vertical tails
机翼安装到机身
06
Propeller Installation
安装桨叶
更多控制量 More control throw
更少控制量Less control throw
舵角 Horns 舵臂 Arms
The table shows the factory settings for the control horns
and servo arms. Fly the aircraft at the factory settings
before making changes.
After flying,you may choose to adjust the linkage positions
for the desired control response.
ElevatorRudderAilerons
这个表格展示了出厂默认设置舵角和舵臂，请用默认设置试飞飞机。飞行之
后，你可以选择调整连杆的位置，以达到期望的控制效果。
05-1
05-2
参考马达座的螺丝孔位，在机身头部钻出四个引导孔。
Refer to the screw's hole position of motor mounting board, drill
4pcs holes on the head of fuselage.
用螺丝固定马，马达线导入机身内。（可用马达自带螺丝）
Fasten motor with screw, put the motor wire inside the
fuselage.(motor's own screw is also available.)
打开仓身盖，安装电调，并连接马达线。
Open the cabin cover, install ESC, and connect motor wire.
插好插销后，机翼后端拧入塑料螺丝固定
住机翼。
After plugging the bolt, fasten the
wing with plastic screws on the
rear-end of wing.
在马达上安装桨叶，
用桨夹锁紧。
Install propeller on
the motor, and
lock it with prop
adapter.
06-1
06-2
a
b
b
a
用尺检查图中机翼，尾
翼的尺寸，确保测量的
a=a，b=b
Check the size of
middle wing and tail
wing with ruler, ensure
a=a，b=b
检查尾翼与机翼的平行情
况，它机身两侧应相等。
Check the parallelism
condition of tail wing
and wing,two sides of
fuselage must be equal.
如发现小量误差，可松
开固定机翼和尾翼的螺
丝做小量的调整，然后
锁紧。
If you find small error,
you can loosen the
screw which fasten
wing and tail wing to
make a litlle
adjustment, then lock
it.
M4*15 螺丝
M4*15 screw
M3*10mm自攻螺丝
Rx.
06-3
06-4
M3*10mm self-tapping screw
Here you can stick one
adhesive tape as handle,
convenient for opening
the cabin.
此处可用粘一个胶带作为
拉手
更多电子设备调试细节可参考以下链接查看（可直接扫二维码）
More details about power system adjustment, please refer to below link: (You can scan QR Code directly.)
桨叶
马达
电调
接收机
电池
http://www.dwhobby.com/art/connection
Y线
Y-wire
Y-wire
Y线
重心位置展示
5
Control Directions Tests
09
Set and Adjust
设置和调试
常规飞行(Normal Flying) 3D飞行 部分飞机支持(3D Flying only support some models)
副翼 Aileron ±（15°-30°） ±40° 或者更大(or larger)
平尾 Elevator ±15° ±40° 或者更大(or larger)
垂尾 Rudder ±15° ±40° 或者更大(or larger)
常用襟翼 Flap （起飞 take-off）15°-20° （降落 Landing）20°-40°
部分特殊机型会有V型尾翼，襟翼，前缘机翼或舵面很小等，可以以常规飞行的角度作为参考，在您不确认且没有有经验人员指导
的情况下，我们建议您先以小角度试飞以确认您的设置是否正确。
Some special models will have V-tails, flaps, leading edge wings, etc., which can be used as a reference for conventional
flight angles. If you do not confirm and there is no experienced person to guide you, we recommend that you first test
at a small angle to confirm that your settings are correct.
Elevator
Aileron
15°-30°
15°
15°
15°
15°
15°-30°
通常情况下，舵面角度的设置如下：
Usually, the control throws set as below:
≈90mm
Display the C.G
Elevator
AileronRudder
遥控器动作 飞机反应
升降杆下拉
Direction rod to the left
升降杆上推
Direction rod to the right
Steering rod to the left
Steering rod to the right
Lifting rod up
Lifting rod down
转向杆向右
转向杆向左
方向杆向右
方向杆向左
地面控制方向测试
升降舵
副翼
Rudder
方向舵
训练飞行模式参考上图设置，运动3D飞行模式请参考3D飞行。在3D飞行时可使用混控把副翼和襟翼联合起来。
≈90mm
注意：设置重心时，可用电池配重，调整电池位置以达到合
适的重心。然后用魔术胶带把电池固定在仓身内。
Note:When you adjust CG, you can use battery as
balance weight, adjust battery positon to find the
suitable CG, then fasten the battery on the cabin with
magic tape.
About the training flying mode, please refer to above picture's setting;
For sport 3D flying mode, please refer to 3D flying.Use mixed control to connect aileron and flap in 3D flying.
-
1
-
2
-
3
-
4
-
5
-
6
Dancing Wings Hobby TCG 14 Basswood Training Airplane ユーザーマニュアル
- カテゴリー
- リモコンのおもちゃ
- タイプ
- ユーザーマニュアル
関連論文
その他のドキュメント
-
Kyosho F-16 FIGHTING FALCON ユーザーマニュアル
-
-
-
-
-
FMS Models FMM133PX 取扱説明書
-
-
FMS Models 1280mm Easy Trainer V2 取扱説明書
-
-
