Goal Zero Yeti Link ユーザーマニュアル

1

2

3

Table of Contents

Important Safety Instructions 1

Get To Know Your Gear 2

How To Install 4

How It Works With Home Energy Storage - TANK MODE 7

How It Works - VEHICLE MODE 11

Charging Indicator Lights 13

Frequently Asked Questions 13

Technical Specifications 15

Français 17

Deutsch 33

Español 49

Italiano 65

Portugués 81

Japanese 97

1

WARNING: Do not exceed 22V input for the Link. Doing so can

cause serious damage to the Yeti and potential bodily injury. Take

note of voltages when using third party solar panels or third party

lead acid batteries with the module. Do not chain solar panels

or lead acid batteries in series (positive to negative, positive to

negative, etc.), as this can result in dangerously high voltages.

WARNING: Never connect a power source to the Yeti Link before

installing into the Yeti. Always connect the Link to the Yeti before

connecting any power source.

IMPORTANT SAFETY INSTRUCTIONS

Please save these instructions

Read all the instructions and cautions before

beginning installation.

No liability is assumed for damages resulting in the use of the

information contained herein.

CAUTION: The Goal Zero Yeti Link outputs very high amperages. Use

only with Goal Zero cables. Altered cables or connectors or 3rd Party

cables or connectors may be incompatible and may cause damage to

components, vehicle or person.

WARNING To reduce risk of fire, injury to persons or damage to

property, use only in the manner intended by Goal Zero

Do NOT disassemble or attempt to repair the module.

Do NOT allow water to enter the module, the Goal Zero Yeti Lithium, or

the Goal Zero Yeti Tank.

Ensure cable is fully inserted and tightly in place before use. Check

upon subsequent uses. For questions, contact Solutions Center at

[email protected] or 1-888-794-6250

Do NOT chain third party solar panels or lead acid batteries in series

(connecting positive to negative, positive to negative, etc.), as this

can result in dangerously high levels of voltage that can cause serious

damage to the Yeti Lithium and potential bodily injury.

Compatible with Yeti 1000, 1000X, 1400, 1500X, 3000, 3000X,

and Yeti 6000X Lithium Power Stations

2

GET TO KNOW YOUR GEAR

Data Transfer Connector

Master 8mm Input

for Yeti Link & Yeti Tank

Expansion Battery

Input Charge Indicator

Pinhole Reset

Button

Lead-Acid State of

Charge Indicator

Blue Connector

Fan Vent

Front of Link Expansion Module

3

EC8 External Battery

Connector

Fan Vent

Back of Link Expansion module

Ensure cable is fully inserted and tightly in place before use. Check

upon subsequent uses. For questions, contact Solutions Center at

[email protected] or 1-888-794-6250

4

HOW TO INSTALL

Tools you’ll need: Phillips Screwdriver

1. Turn off all the output ports and unplug the Yeti from any power

source.

2. Open the lid of the Yeti and remove the expansion module carriage

from the Yeti by removing the six screws and sliding out the

carriage.

3. Insert the included Link Lock into the opening facing the back of

the Yeti and line up the screw holes on the Link Lock with the holes

on the Yeti.

4. Take the blue connector and micro -USB cable on the Link module and

insert them into the module and micro-USB ports on the Yeti, matching

positive to positive, negative to negative, and micro to micro.

5

5. Gently set the Link into place, tucking the cables into the opening.

6. Using the provided four screws, secure the Link into place.

7. Using the 8mm port, plug the power source into the Link.

Black Cable (-)

-

Red Cable (+)

Blue Connector

Data Transfer

Connector

+

Ensure cable is fully inserted and tightly in place before use. Check

upon subsequent uses. For questions, contact Solutions Center at

[email protected] or 1-888-794-6250

WARNING: Do not exceed 22V input for the module. Doing

so can cause serious damage to the Yeti and potential bodily

injury. Take note of voltages when using third party solar panels

with the module. Do not chain solar panels in series (positive

to negative, positive to negative, etc.), as this can result in

dangerously high voltages.

6

Ensure cable is fully inserted and tightly in place before use. Check

upon subsequent uses. For questions, contact Solutions Center at

[email protected] or 1-888-794-6250

8. Proceed to plug in the EC8 cable and slide either the straight or the

90-degree EC8 cable holder over the cable and into the slots of the Link

Lock. When the power source is correctly plugged in, the Input Charge

Indicator light will turn blue. When the Tank is correctly connected to the

Link and the power source is plugged in, the Lead-Acid State of Charge

Indicator light will begin flashing green. NOTE: Upon plug-in, all LEDs will

turn on, then off before correct lights are displayed. This may take up to

30 seconds.

9. Power source will charge the Yeti first. When the Yeti is fully charged,

power will begin to store in the Tank. NOTE: Power coming in from the

8mm port will flow through the Tank first and then into the Yeti. Without

a Tank or third party battery attached, this port will not charge the Yeti

directly.

EC8 External

Battery Cable

or

7

8mm Output

Power Supply

(Included)

Yeti Link

Expansion Module

HOW IT WORKS WITH HOME ENERGY STORAGE - TANK MODE

The Goal Zero Yeti Link Expansion Module integrates with a Goal Zero

Yeti Lithium or Yeti X Portable Power Station and Goal Zero Yeti Tank

Expansion Battery to increase your energy storage capacity. The Link is

a Lithium Charge Controller that will draw up to 80A Max Current from a

Lead-Acid power source.

AC Wall

Outlet

Goal Zero

Solar Panels

(Sold Separately)

Goal Zero Yeti Tank

Expansion Battery

Goal Zero Lithium Yeti and

Goal Zero Yeti Link Expansion Module

REQUIRED (sold separately) REQUIRED (sold separately)

+

8

1. Once Link Module is installed into the Yeti you will be able to attach Goal

Zero Yeti Expansion Tanks. To do this take the male EC8 cable from the

Expansion Tank and plug it into the EC8 External Battery Connector on

the Link Module that is installed in the Yeti Power Station.

2. Then take either the included power supply or a Goal Zero Solar Panel

(sold separately) and plug the 8mm barrel connector (blue ring) into the

8mm input port on the Link Module.

Note: Do not plug a tank into itself when multiple tanks are

connected.

3. Power will flow into the battery and then into the Yeti power station.

Once the power station is full the power will then start filling up the

Tank.

NOTE

1. The 8mm port on the Link is the only way to charge both the Yeti and

Tank. Input ports on the Yeti display will only charge the Yeti, not the

Tank.

2. When Link and Tank are properly installed, power passes through the

8mm port to the Tank and then into the Yeti. Thus, without a Tank or

third party battery attached, you cannot charge the Yeti directly using

the 8mm port on the Link.

WARNING: Do not exceed 22V input for the module. Doing

so can cause serious damage to the Yeti and potential bodily

injury. Take note of voltages when using third party solar panels

with the module. Do not chain solar panels in series (positive

to negative, positive to negative, etc.), as this can result in

dangerously high voltages.

9

IMPORTANT SAFETY INSTRUCTIONS

Please save these instructions

Read all the instructions and cautions before

beginning installation.

Goal Zero recommends installation of the Yeti Link Vehicle Charging kit be

installed by trained professional. Under no circumstance should the Goal

Zero Yeti Link be installed with out the technical skills, technical information,

tools and equipment required to properly complete the necessary

procedures

Do NOT install a secondary battery in between the Battery and the Yeti Link

Module

Improper connections will damage the Yeti Link Module/Accessory cables

and/or cause serious injury or death. Be sure that all wiring is connected to

the appropriate polarity

Make sure cables are securely connected. Check cables periodically

especially before and after uneven roadways

Confirm cables are installed correctly with no risk of pinching or abrasion.

Pinching cables or any means of exposing internal cables can lead to

malfunctions or fires

Keep live wires , terminals, and other bare parts away from contact with

each other and other metal parts

Always wear eye protection when making battery connections

Always use rubber insulating grommet when drilling through steel panels to

run the EC8 cable

Never route electrical cables across sharp edges

Never route electrical cables near parts that get hot

Never route electrical cables over battery terminals

Never route electrical cables through or near moving parts

Electrical cables should be safe from road spray, rain runoff, sand or gravel

from road surface.

Goal Zero rejects any liability for problems and damage caused by the

system being installed by untrained personnel.

The vehicle owner is responsible for the correct operation of the appliance

Keep away from sources of heat (e.g. too close to exhaust system

components or directly behind the radiator, etc.).

10

WARNING: Do not exceed 22V input for the Link. Doing so can cause

serious damage to the Yeti and potential bodily injury. Take note of

voltages when using third party solar panels or third party lead acid

batteries with the module. Do not chain solar panels or lead acid

batteries in series (positive to negative, positive to negative, etc.),

as this can result in dangerously high voltages.

WARNING: Never connect a power source to the Yeti Link before

installing into the Yeti. Always connect the Link to the Yeti before

connecting any power source.

WARNING: To reduce risk of fire, injury to persons or damage to

property, use only in the manner intended by Goal Zero

WARNING: The Goal Zero Yeti Link Vehicle Charging Kit transmits,

power into the Link Module and Yeti at very high amperages up to

80A Max Current. Use Extreme caution when installing. Use only

Goal Zero supplied cables and connections in installation. If installed

with 3rd party connections or alterations are made to Goal Zero

suppled cables damage to components, vehicle or person may occur.

WARNING: Improper connections will damage the Yeti Link Vehicle

Charging kit and/or cause serious injury or death. Be sure that all

wiring is connected to the appropriate polarity

11

Vehicle

Goal Zero

Solar Panels

(Sold Separately)

Goal Zero Yeti Tank

Expansion Battery

Goal Zero Yeti Lithium and

Goal Zero Yeti Link Expansion Module

REQUIRED (sold separately)

(sold separately)

+

Quickly and easily recharge a Yeti Lithium (1000 or higher) from your vehicle

while on the move. Charge rates vary from 25A - 80A Max Current (300W -

750W) depending on Yeti Lithium size and capacity.

How it Works

When placed in “Vehicle Mode,” the Yeti Link allows your Yeti Lithium to safely

pull power from your vehicle’s alternator while the vehicle is running and stop

pulling power when the vehicle is off.

NOTE: Yeti Link must be in Vehicle Mode to utilize this feature or it will drain

your vehicle’s battery. All Links come standard set in “Tank Mode.”

1. Once Link is installed in Yeti, switch Link from Tank Mode to Vehicle

Mode by pushing the pinhole reset button on top of the Link four times.

2. Indicator lights will turn on and blink together when the Link is

successfully placed in Vehicle Mode.

3. To switch back to Tank Mode, press pinhole reset button on top of the

Link four more times. Indicator lights will scroll from bottom to top

individually when the Link is successfully placed in Tank Mode. NOTE:

Do NOT place back in Tank Mode while connected to your vehicle.

HOW IT WORKS - VEHICLE MODE

Pinhole Reset Button

12

WARNING: Ensure that you only use Goal Zero products between

your Link and Alternator. Any other cables or wiring is not

supported or recommended as these cables need to be rated to

carry a minimum of 80A Max Current

Ensure cable is fully inserted and tightly in place before use.

Check upon subsequent uses. For questions, contact Solutions

Center at support@goalzero.com or 1-888-794-6250

4. Once Link is switched to Vehicle mode you will be able to connect to

your vehicles +/-battery or alternator. By using the Goal Zero EC8

Extension Cable.

Note: only use authentic Goal Zero cables to do this.

DO NOT use more than one Extension Cable

DO NOT have a secondary battery in between the Link Module

and the vehicle alternator or main battery

5. Connect the Ring Terminal Cable to the positive and negative terminals

on the either the main battery or the alternator.

6. Improper connections will damage the Yeti Link Module/Accessory

cables and/or cause serious injury or death. Be sure that all wiring is

connected to the appropriate polarity

7. Plug the Male end of the EC8 Ring Terminal cable into the Female end of

the EC8 Extension cable.

8. Plug male end of Extension Cable into the External EC8 port of the Link

Module and slide either the straight or the 90-degree EC8 cable holder

over the cable and into the slots of the Link Lock.

• Make sure cables are securely connected. Check cables

periodically especially before and after uneven roadways.

EC8 External

Battery Cable

or

13

CHARGING INDICATOR LIGHT

Input Charge Indicator:

FLASHING BLUE - Power source is correctly plugged into

8mm input and charging.

BLUE - Lead-Acid battery is full.

Lead Acid State of Charge Indicator:

1 LED LIGHT - Lead-Acid battery is 25% full or less

2 LED LIGHTS - Lead-Acid battery is 25% - 50% full

3 LED LIGHTS - Lead-Acid battery is 50% - 75% full

ALL LED LIGHTS - Lead-Acid battery is 75% full or more

Error LED

FLASHING RED - Yeti is in an over voltage condition or lead

acid battery is in an under voltage condition. Disconnect

all Tank Cables from Link and Yeti and please call our solar

experts at 888-794-6250.

NOTE

1 The 8mm port on the Link is the only way to charge both the Yeti and

Tank. Input ports on the Yeti display will only charge the Yeti, not the Tank.

2 When Link and Tank are properly installed, power passes through the

8mm port to the Tank and then into the Yeti. Thus, without a Tank or third

party battery attached, you cannot charge the Yeti directly using the 8mm

port on the Link.

FREQUENTLY ASKED QUESTIONS

Q: I’m charging my Yeti and it is connected to one or more Tank batteries,

but my Tank batteries are not filling up. What should I do?

A: First, make sure you are using the input on your Link to charge your

system. This input is the only way to charge both your Tank(s) and Yeti

at the same time. If you are using the correct input and still having a

problem, try resetting by reinstalling your Link.

Q: I installed my Link into my Yeti, connected my batteries, and I’m not

showing a charge. What’s going on?

A: Upon initial installation, the Link needs time to identify which type of Yeti

you own in order to maximize performance. It can take up to 30 seconds

to start operating.

14

Q: Can I use third party, non-Goal Zero lead-acid batteries with the Link?

A: Although not recommended yes, you can use any 12V SLA or AGM deep

cycle lead acid battery with the Link. However, you will need a Goal Zero

Male Link Chaining Cable to connect your batteries to the Link.

Q: If I’m using my own third party lead acid batteries, how do I wire them up?

A: When connecting multiple 12V lead-acid batteries to your Link, be sure

to connect the batteries in parallel. Parallel connections will increase your

current rating, but the voltage will stay the same.

WARNING: Connecting batteries in series will increase the voltage,

causing damage to the unit and possible personal injury or death.

Q: How many lead acid batteries can I plug into the Link?

A: You can attach as many 12V lead-acid batteries to your Link as you’d like.

Q: Why is my Link only charging my Yeti up to 98%?

A: The Link will only charge a Newer generation Yeti Lithium to 98%. This

protection is in place to protect and prolong the life of your battery. Second

generation Yeti Lithium power stations equipped with the latest firmware

updates can be charged to 100%.

Q. Once you put the Link into Vehicle mode, does it stay in Vehicle mode until

you put it back into Tank Mode?

A. The Yeti Link will stay in Vehicle mode until you manually change it back to

Tank mode. If moving the unit from your vehicle to then chain it to the Tank

batteries in your home, you will need to change the Link from Vehicle Mode

to Tank Mode.

Q. Would the solar still feed the Vehicle battery when the Vehicle is not

running?

A. Yes, if you have a solar panel plugged directly into the 8mm port on the Yeti

Link, the panel will be charging both the Yeti and your Vehicle battery when

it isn’t running.

15

TECHNICAL SPECIFICATIONS

80A Max Current from External Tanks/

Power Source to the Yeti’s internal

Lithium Battery

Charges the following:

GOAL ZERO Yeti 1000X @ Max Input 605W

GOAL ZERO Yeti 1500X @ Max Input 750W

GOAL ZERO Yeti 3000X @ Max Input 750W

GOAL ZERO Yeti 6000X @ Max Input 750W

Ports: Do not exceed 22V Input

8mm Charging port 14 - 22V, Do not exceed

100W or 7.5A

External Battery Connector 80A Max Current

10.7 - 15V

General:

Weight 1.5 lbs (680 g)

Dimensions 10.25 x 3.3 x 1.5 in (26

x 8.4 x 3.8 cm)

Operating Usage Temp 32-104 F (0-40C)

Warranty 12 months

Certs

Yeti Link Expansion Module

16

17

ATTENTION : Ne dépassez pas plus de 22V en entrée du module

Link. Cela pourrait causer des dommages sérieux au Yeti et

d'éventuelles blessures corporelles. Prenez note des tensions

électriques lors de l'utilisation de panneaux solaires tiers ou des

batteries plomb-acide tierces avec le module. N'enchaînez pas

plusieurs panneaux solaires ou batteries plomb-acide en série

(positive à négative, etc.), car cela peut entraîner des niveaux de

tension dangereusement élevés.

ATTENTION : Ne jamais connecter une source d'alimentation au Yeti

Link avant de l'avoir installé sur le Yeti. Connectez toujours le module

Link au Yeti avant de brancher une source d'alimentation.

CONSIGNES DE SÉCURITÉ IMPORTANTES

Veuillez conserver ces consignes

Lisez toutes les consignes et mises en garde avant de

commencer l'installation.

Aucune responsabilité n'est assumée pour les dommages résultant

del'utilisation des informations contenues dans ce document.

ATTENTION : le module de liaison Goal Zero Yeti Link produit des

ampérages très élevés. L'utilisez uniquement avec des câbles

Goal Zero. Des câbles ou connecteurs modifiés ou des câbles ou

connecteurs tiers peuvent être incompatibles et endommager les

composants, le véhicule ou les personnes.

AVERTISSEMENT Pour réduire les risques d'incendie, de blessures

corporelles ou de dommages matériels, utilisez uniquement de la

manière prévue par Goal Zero.

NE PAS désassembler ou tenter de réparer le module vous-même.

NE PAS laisser de l'eau pénétrer dans le module, le Goal Zero Yeti

Lithium ou le réservoir Goal Zero Yeti Tank.

Assurez-vous que le câble est inséré entièrement et fixé correctement

avant l'utilisation. Vérifiez avant toute utilisation ultérieure. Si vous

avez des questions, contactez notre Centre de Solutions à l'adresse

[email protected] ou au numéro 1-888-794-6250

NE PAS enchaîner plusieurs panneaux solaires tiers ou batteries plomb-

acide en série (connexion positive à négative, positive à négative,etc.),

car cela peut entraîner des niveaux de tension dangereusement

élevés qui pourraient causer des dommages sérieux au Yeti Lithium et

d'éventuelles blessures corporelles.

Compatible avec les stations d'alimentation Yeti 1000, 1000X, 1400,

1500X, 3000, 3000X et Yeti 6000X au lithium

17

ページを読み込んでいます...

Goal Zero Yeti Link ユーザーマニュアル

関連論文

その他の書類