Goalzero GZ96110 ユーザーガイド

1

2

The controllers have a waterproof design, suitable for indoor or

outdoor use.

Do not disassemble the controller.

Lead acid, LiFePO4, LTO batteries can be dangerous. Ensure no sparks

or flames are present when working near batteries.

Eye protection should always be used. Never short circuit the battery

Given sufficient light solar panels always generate energy even when

they are disconnected.

Accidental ‘shorting’ of the terminals or wiring can result in sparks

causing personal injury or a fire hazard. We recommend that you

cover up the panel(s) with some sort of soft cloth, so you can block all

incoming light during the installation. This will ensure that no damage

is caused to the Solar Panel or Battery if the wires are accidentally

short circuited.

Always install a battery fuse on each circuit including the solar

controller. Fuse inlcude with Goal Zero cables.

Do not reverse connect the wires to the solar panel or battery

IMPORTANT SAFETY INSTRUCTIONS

1

Important Safety Instructions

Features 2

Get to Know Your Gear 3

Mounting The Charge Controller 5

Wiring Connection 6

Operation - LCD Display 7

Charging Stages 9

Operations LED Indication 11

Abnormal Operations Mode 12

Maintenance 13

Technical Specifications 13

Français 16

Deutsch 30

Español 44

Italiano 58

Português 72

日本語 86

Table of Contents

2

• Advanced MCU control pulse width modulated (PWM) technology, high efficiency.

• Target for LiFePO4, LTO (Lithium Titanium Oxide), Gel, AGM, Conventional lead-acid

(WET) and Calcium Batteries.

• Built in regulator to prevent your battery from being overcharged. Overcharging occurs

when the charge voltage is unregulated. This can result in premature battery failure.

• Comes with a regulator to prevent undercharging of your battery - a condition that is

very common in solar charging but especially with conventional lead-acid or calcium

batteries. The unit provides an automatic Equalization feature for deeply drained

Conventional lead acid battery or Calcium battery, as well as provides a cycling

automatic Equalizing feature every 28 days.

• Can be connected to the battery permanently to keep the battery fully charged by using

a process called “floating”. This means the controller will stop charging when the battery

is full and will automatically start charging the battery as required. This process will also

reduce water loss and help prevent the battery from ‘drying out’.

• Protects your battery from discharge at night. Under low light or no light conditions the

solar panel voltage could be less than the battery voltage. The unit contains a special

circuit which prevents current flowing back from the battery and into the solar panel.

• Colored LED’s to easily indicate the operational status and battery conditions.

• Digital LCD to directly display battery voltage, charging current, charging capacity (Amp

hour), battery types and fault codes.

• Provides external battery temperature sensor (Requires additonal wires - not included).

• Multi charging protections against reverse polarity, short circuit, over temperature, over

voltage, etc.

• Surface Mount, Flush Panel Mount or Portable solar kits Mount options.

• Conformal-coating circuit boards and plated terminals for inclement weather.

Features

3

Get To Know Your Gear

The Goal Zero 20A Charger Controller is used to connect Goal Zero Solar Panels directly

to external batteries. The Charge controller connects Goal Zero Solar Panels to 12V

battery (AGM, LiFePO4, LTO, Gel, Lead Acid, and Calcium Batteries) to charge and

monitor the charging of the battery. Perfect for RV’S, motorcycles, snowmobiles, tractors,

watercraft, lawnmowers, cars, etc.

Note:

• Will not work with Nomad 5,7,7+,and 10.

• Optional SAE to Ring terminal and SAE to Alligator Clips sold separately

4

LCD DisplayLED Indication Volt / Amp Button Battery Type Button

Inline Fuse

Get To Know Your Gear

High Power Port

(HPP) Input

5

Mounting The Device

The Solar Controller has two mounting options.

1. Surface mount:

The quickest and easiest way to mount the unit is to use self-tapping screws and

mount the unit to a flat surface.

2. Portable panel kit mount:

Mounting Bracket

(Sold Seperately on Goalzero.com SKU 98365)

6

To protect the Battery and the Solar Panel, we strongly recommend that you place an

in-line fuse on the positive wire on both the “Solar” and “Battery” Circuits. 25A fuse for 20A

controller (As close to the Battery /Panel as possible). Fuse included with Goal Zero cables.

For the Battery connection we recommend using Goal Zero Spade to SAE cable (98370)

The Solar Controller has 4 terminals which are clearly marked ‘Solar’ and ‘Battery’.

There is a (12V) and earth (GND) terminal for each circuit.

Refer to the wiring diagram below.

Correct Wire Size:

Please refer to the wire size chart below to determine the minimum size wire needed for

each connection. This will also ensure you get the best performance out of your solar

regulator.

1. Using the stranded wires, screw tightly the wires to the “Solar” and “Battery” terminals

on the back of controller and connect to the Solar Panel and Battery.

2. If the cable gauge is too large to fit into the terminals of the controller, please properly

peel the part of copper wires prior to installation.

When the connections are completed, the Solar Controller will start working automatically.

Rated

Current

Cable length

One-way distance

Solar panel - Controller - Battery (Meter)

< 3M 3-6M 6-9M 9-12M

20AMP Cable size (AWG) 16AWG 14AWG 12AWG 10AWG

Wiring Connections

7

Operation - LCD Display

Please check your battery manufacturer’s specifications to select correct battery type. The

unit provides 6 battery types for selections: LiFePO4, LTO, Gel, AGM, WET (conventional

lead acid), and Calcium.

Press BATTERY TYPE button and hold for 3 seconds to go into your battery type selection

mode, the battery types you select will be shown on the LCD meter, the default setting is

AGM Battery; the controller will automatically memorize your battery type setting.

Caution: Incorrect battery type setting may damage your battery.

When the controller powers on, the unit will run self-qualify mode and automatically show

below items on LCD before going into charging process.

Self-test starts, digital meter segments test

Software version test

Rated voltage and current test

External battery temperature sensor test (if connected)

Indicates the solar panel connected

V A

ºC

8

After going into charging process, the LCD displays the charging statues as below:

Press VOLT / AMP button in sequence, the LCD will display in turn with Battery Voltage,

Charging Current, Charged Capacity (Amp-hour) and Battery Temperature (if external

temperature sensor connected).

Display in the daytime-

Display during the night-

Alternatively Display voltage and FUL when battery is fully charged-

V

A V

ºC

V

ºC

V

9

You also can visually monitor your battery charging condition via an LCD bar on the top

of LCD meter, if the battery is in the charging process, the LCD bar will be flashing; if the

battery is fully charged, the LCD bar will turn on.

The VOLT / AMP button can be changed at any time during charging process.

The LCD also can be treated as an independent voltage meter or thermometer. A voltage

less than 11.5V Volts indicates that the battery is discharged and needs re-charging.

CHARGING STAGES

The unit has a 5-stage charging algorithm.

Soft Charge (Level 1) –Bulk Charge (Level 2)-Absorption charge (Level 3) – Equalizing Charge*

(Level 4) - Float Mode (Level 5)

Soft Charge- When batteries suffer an over-discharge, the controller will softly ramp the

battery voltage up to 10V.

Bulk Charge- Maximum current charging until batteries rise to Absorption level

Level 1

Level 2

Level 3

Level 4

Level 5

Charging Stages

10

Absorption Charge- Constant voltage charge and battery is over 90%.

Equalization Charge*- Only for WET battery or Calcium battery type, when the battery is

deeply drained below 10V, it will automatically run this stage to bring the internal cells as an

equal state and fully complement the loss of capacity. (LiFePO4, LTO, Gel and AGM battery

do not run Equalization charge)

Float Charge- Battery is fully charged and maintained at a safe level. A fully charged Lead

acid battery (GEL, AGM, WET battery) has a voltage of more than 13.6 Volts; A fully charged

LiFePO4 or LTO battery has a voltage level of 13.4V.

11

The 6 LED’s

indicate the

charging status

and the battery

condition Red Blue Green Green Yellow Red

Solar Power

Present-

No battery

connected

ON OFF OFF OFF OFF Flash

Soft charging ON Flash OFF OFF OFF ON

Bulk charging ON ON OFF Subject to battery voltage

Absorption

charging ON ON OFF ON OFF OFF

Equalization

charging ON ON OFF ON OFF OFF

Float charging ON OFF ON OFF OFF OFF

Solar panel weak Flash OFF OFF Subject to battery voltage

At night no

charge OFF OFF OFF Subject to battery voltage

Battery Voltage

below 11.5V (+/-

0.2V) ON ON OFF OFF OFF ON

Battery Voltage

between 11.5V -

12.5V(+/-0.2V) ON ON OFF OFF ON OFF

Battery Voltage

above 12.5V(+/-

0.2V) ON ON OFF ON OFF OFF

FULL

Operation - LED Indication

12

Solar panel

Abnormal Mode LCD Display LED Indication LCD Backlight

Solar panel weak Flash ON

Solar panel reverse

connection Flash Flash

Solar panel over

voltage (> 26.5V) Flash Flash

Solar panel

Abnormal Mode LCD

Display LED Indication LCD

Backlight

Battery

disconnected or

less than 3.0V Flash Flash Flash Flash

Battery reverse

connection Flash Flash

Battery over

voltage than >

17.5V Flash Flash

Battery

temperature over

65°C Flash Flash Flash Flash

Solar panel

Abnormal Mode LCD Display LED Indication LCD Backlight

The controller

over temperature

protection Flash

Abnormal Operation - LED Indication

13

Electrical Parameters Parameter

Rated solar panel amps GZ-10 20A

Normal input Solar cell array voltage 15-22V

Max. solar cell array voltage (output has no load) 25V

The controller lowest operating voltage at solar or

battery side

8V Minimum

Charging characteristics

Start Voltage at 25°C 3-10V

Charge Voltage at 25°C

LTO battery-14.0V

Gel battery-14.1V

LiFePO4 battery-14.4V

AGM battery-14.4V

WET battery-14.7V

Calcium battery-14.9V

Equalizing voltage at 25°C WET or Calcium battery-15.5V

Float voltage at 25°C Gel, AGM, WET, Calcium batteries - 13.6V

LTO and LiFePO4 – 13.4V

Battery temperature compensation coefficient -24 mV/°C

Protection

Against reverse polarity or short circuit

No reverse current from battery to solar at night

Over temperature protection during charging 65°C

Technical Specifications

Maintenance

The controller is maintenance free. If the connection wire is damaged or loosed, please

replace the new wires or tighten the screws. The case should be cleaned occasionally with

dry cloth.

14

Electrical parts

Input output terminal M5 terminals

Temp-sensor port (Press and Release type) DA 250-350 2P

Physical Parameters

Controller housing material Plastic, Standard ABS

Power terminal maximum stranded wire size #12 AWG stranded- 3 mm2

IP grade IP65

Environmental characteristics

Size (L*W*H) 6.10 x 3.9 x 1.02 in (15.5 x 9.91 x 2.6 cm)

Weight 9.7oz (272g)

Operating temperature -25 to 50 °C /- 13 to 122 °F

Storage temperature -40 to 85°C / - 40 to 185 °F

Operating Humidity range 100% no condensation

Approvals IC, FCC, CE-EMC, CE-LVD

15

16

Les régulateurs ont une conception étanche, adaptée à une utilisation

intérieure ou extérieure.

Ne pas démonter le régulateur. L'amener à une personne qualifiée si

l'appareil doit être réparé.

Les batteries plomb-acide, LiFePO4, LTO peuvent être dangereuses.

Veillez à ce qu'aucune étincelle ou flamme ne soit présente lorsque

vous travaillez à proximité de batteries.

Il faut toujours utiliser une protection oculaire. Ne jamais court-

circuiter la batterie.

Si la lumière est suffisante, les panneaux solaires produisent toujours

de l'énergie, même lorsqu'ils sont déconnectés.

Un court-circuit accidentel des bornes ou du câblage peut provoquer

des étincelles et entraîner des blessures ou un risque d'incendie.

Nous vous recommandons de couvrir le(s) panneau(x) avec une

sorte de tissu doux, afin de pouvoir bloquer toute lumière entrante

pendant l'installation. Cela permettra de s'assurer qu'aucun dommage

n'est causé au panneau solaire ou à la batterie si les fils sont

accidentellement court-circuités.

Installez toujours un fusible de batterie sur chaque circuit, y compris

lerégulateur solaire.

Ne pas inverser la connexion des fils au panneau solaire ou à la batterie

CONSIGNES DE SÉCURITÉ IMPORTANTES

17

• Technologie avancée de commande MCU à modulation de largeur d'impulsion (PWM),

haute efficacité.

• Cible pour LiFePO4, LTO (oxyde de lithium-titane), gel, AGM, plomb-acide conventionnel

(WET) et batteries au calcium.

• Régulateur intégré pour éviter que votre batterie ne soit surchargée. La surcharge

se produit lorsque la tension de charge n'est pas régulée. Cela peut entraîner une

défaillance prématurée de la batterie.

• Livré avec un régulateur pour éviter que votre batterie ne soit sous-chargée. Dans le

domaine de l'énergie solaire, une sous-charge de la batterie se produit toujours, en

particulier sur certaines batteries conventionnelles plomb-acide ou calcium. L'appareil

offre une fonction d'égalisation automatique pour les batteries conventionnelles plomb-

acide ou calcium profondément vidées, ainsi qu'une fonction d'égalisation automatique

cyclique tous les 28 jours.

• Peut être connecté à la batterie de façon permanente pour maintenir la batterie

complètement chargée en utilisant un processus appelé "floating". Cela signifie que le

régulateur arrête la charge lorsque la batterie est pleine et commence automatiquement

à charger la batterie selon les besoins. Ce processus permettra également de réduire

les pertes d'eau et d'éviter que la batterie ne "s'assèche".

• Protège votre batterie de la décharge pendant la nuit. Dans des conditions de faible

luminosité ou d'absence de lumière, la tension du panneau solaire peut être inférieure

à celle de la batterie. L'appareil contient un circuit spécial qui empêche le retour du

courant de la batterie vers le panneau solaire.

• Des LED colorées pour indiquer facilement l'état de fonctionnement et l'état de la batterie.

• LCD numérique pour afficher directement la tension de la batterie, le courant de charge,

la capacité de charge (Ampère-heure), les types de batterie et les codes des défauts.

• Fournit un capteur externe de température de la batterie (nécessite des fils

supplémentaires - non inclus).

• Protections multicharges contre les inversions de polarité, les courts-circuits, les

surchauffes, les surtensions, etc.

• Options de montage : montage sur surface, montage sur panneau encastré ou kits

solaires portables.

• Les cartes de circuits imprimés à revêtement conforme et les terminaux plaqués

s'appliquent aux environnements hostiles.

Caractéristiques

18

Apprenez à Connaître Votre Équipement

Les régulateurs de charge Goal Zero 20A sont utilisés pour connecter les panneaux

solaires Goal Zero directement à des batteries externes. Le régulateur de charge

connecte les panneaux solaires Boulder, Ranger et Nomad à une batterie de 12V

(AGM,LiFePO4, LTO, Gel, Plomb Acide et Calcium) pour charger et surveiller la

chargedela batterie. Parfait pour les véhicules de loisirs, les motos, les motoneiges,

lestracteurs, les bateaux, les tondeuses à gazon, les voitures, etc.

Remarque :

• Ne fonctionnera pas avec Nomad 5, 7, 7+ et 10.

• Bornes SAE à bague et SAE à crocodile optionnelles vendues séparément

ページが読み込まれています...

Goalzero GZ96110 ユーザーガイド

Goalzero GZ96110 ユーザーガイド

他の言語で

関連論文

その他のドキュメント