V1.1
CR-200B
1
22
3
2
1
4
5
6
7
9
10
11
12
8
Touch Screen I 触摸屏
Printer Cover I 上罩
1
3
4
CR-200B
200*200*200mm
360W
Storage card/USB | 存储卡脱机打印或联机打印
Input | 输入：AC 100-240V 50/60Hz Output | 输出：DC 24VPower specification | 电源规格
*Tips: the above accessories are for reference only, please refer to the physical accessories!
注意：以上配件仅供参考，请以实物为准！
5
十字螺丝刀
Cross Screwdriver
喷嘴
Nozzle
6
7
1. Before initial leveling, tighten the four leveling nuts at the bottom of the platform 2. Select Settings→Leveling
Model→Auxiliary Leveling, click the number ①/②/③/④/⑤
1.初次调平前，拧紧平台底部的四个调平螺母 2.选择设置→调平模式→辅助调平,点击数字①/②/③/④/⑤
8
9
10
We can use a piece of A4 paper to assist in leveling, so that the nozzle can just scratch the A4 paper. Adjust the
leveling nuts on the four sides in turn until you can feel the slight resistance from the nozzle when pulling the A4
paper.
我们可以利用一张A4纸辅助调平，使喷嘴刚好能在A4纸上产生划痕。依次完成四个边上上调平螺母的调节，不断调整
直到在拉动A4纸时能感受到来自喷嘴的轻微阻力。
11
100 100
Diagonal Pliers
剪钳
12
13
When the temporary temperature hits the target temperature, feed in the filaments to the nozzle and keep await until you
see liquid filament comes out of the nozzle.
当前温度达到目标温度时,将耗材插入挤出机小孔直至喷嘴位置,等看到喷嘴处有耗材流出即表示耗材已经装载完成。
CR-200B
200
200
200
CR-200B
200
200
200
14
15
6.Insert the storage card →Print
→Select the file to print .
插入存储卡→打印→选择由菜单→
要打印的文件。
File names must be Latin letters or numbers, not Chinese
characters or other special symbols.
文件名需为拉丁字母或数字，不能为汉字或其他特殊符号。
Notes: For details on the software instructions, please refer
to the slicing software manual in the storage card!
温馨提示：软件使用说明详情，请见存储卡内切片软件使用手册！
5.Generate G-code, and save the gcode file to storage card.
生成G代码→保存到存储卡。
X-axis motor port
X轴电机接口
Y-axis motor port
Y轴电机接口
Z-axis motor port
Z轴电机接口
E-axis motor port
E轴电机接口
Storage card slot
存储卡卡槽
Micro USB port
Micro USB接口
Screen port
显示屏接口
Reserved port
预留接口
Filament detector
断料检测
Part cooling fan port 1
常开风扇1
Part cooling fan port 2
常开风扇2
Lighting interface
照明灯接口
Nozzle interface
喷头接口
Hot bed interface
热床接口
24V power input
24V电源输入
B_L touch port
B_L touch接口
Nozzle thermistor
喷头热敏电阻
Hot bed thermistor
热床热敏电阻
Z axis limit switch port
Z轴限位开关接口
Y-axis limit switch port
Y轴限位开关接口
X-axis limit switch port
X轴限位开关接口
Controllable fan 3
可控风扇3
Controllable fan 2
可控风扇2
Controllable fan 1
可控风扇1
16
/
