Sony BKDS-2010 インストールガイド

ブランド: Sony

モデル: BKDS-2010

カテゴリー: ビデオコンバーター

タイプ: インストールガイド

DIGITAL VIDEO SWITCHER

DVS-2000C

SWITCHER CONTROL PANEL

INSTALLATION MANUAL

1st Edition

BKDS-2010

BZS-2010 BZS-2020 BZS-2090 BKDS-2020

BKDS-2021 BKDS-2022 BKDS-2031 BKDS-2032

BKDS-2041 BKDS-2050 BKDS-2060 BKDS-2061

BKDS-2062 BKDS-2070 BKDS-2071 BKDS-2072

SAFETY CHECK-OUT

After correcting the original service problem, perform

the following safety checks before releasing the set

to the customer:

Check the metal trim, “metallized” knobs, screws,

and all other exposed metal parts for AC leakage.

Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to

earth ground and from all exposed metal parts to any

exposed metal part having a return to chassis, must

not exceed 3.5 mA. Leakage current can be

measured by any one of three methods.

1. A commercial leakage tester, such as the

Simpson 229 or RCA WT-540A. Follow the

manufacture’s instructions to use these

instruments.

2. A battery-operated AC milliammeter. The Data

Precision 245 digital multimeter is suitable for

this job.

3. Measuring the voltage drop across a resistor by

means of a VOM or battery-operated AC

voltmeter. The “limit” indication is 5.25 V so

analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa SH-

63Trd are examples of a passive VOM that is

suitable. Nearly all battery operated digital

multimeters that have a 20 V AC range are

suitable (see Fig. A).

Ω

Fig. A. Using an AC Voltmeter to check AC leakage.

DVS-2000C Serial No. 10001 and

Higher

BZS-2010 Serial No. 10001 and

Higher BZS-2020 Serial No. 10001

and Higher BZS-2090 Serial No. 10001

and Higher BKDS-2010 Serial No.

10001 and Higher BKDS-2020 Serial

No. 10001 and Higher BKDS-2021

Serial No. 10001 and Higher

BKDS-2022 Serial No. 10001 and

Higher BKDS-2031 Serial No.

10001 and Higher

BKDS-2032 Serial No. 10001 and

Higher

BKDS-2041 Serial No. 10001 and

Higher

BKDS-2050 Serial No. 10001 and

Higher

BKDS-2060 Serial No. 10001 and

Higher

BKDS-2061 Serial No. 10001 and

Higher

BKDS-2062 Serial No. 10001 and

Higher

BKDS-2070 Serial No. 10001 and

Higher

BKDS-2071 Serial No. 10001 and

Higher

BKDS-2072 Serial No. 10001 and

Higher

VORSICHT

Um Feuergefahr und die Gefahr eines elektrischen

Schlages zu vermeiden, darf das Gerät weder Regen

noch Feuchtigkeit ausgesetzt werden.

Um einen elektrischen Schlag zu vermeiden, darf das

Gehäuse nicht geöffnet werden. Überlassen Sie

Wartungsarbeiten stets nur einem Fachmann.

Bescheinigung des Herstellers / Importeurs

Hiermit wird bescheinigt, daß die Digital-Video-

Schalteinheit DVS-2000C in Übereinstimmung mit den

Bestimmungen der BMPT-Amtsblatt Vfg 243/1991 und

Vfg 46/1992 funkentstört ist. Der vorschriftsmäßige

Betrieb mancher Geräte (z.B. Meßsender) kann

allerdings gewissen Einschränkungen unterliegen.

Beachten Sie deshalb die Hinweise in der

Bedienungsanleitung. Dem Bundesamt für Zulassungen

in der Telekommunikation wurde das Inverkehrbringen

dieses Gerätes angezeigt und die Berechtigung zur

Überprüfung der Serie auf die Einhaltung der

Bestimmungen eingeräumt.

Sony Deutschland GmbH

Hugo Eckener Str. 20

50829 Köln

Hinweis

Gemäß der Amtsblätter des BMPT Nrn. 61/1991 und 6/

1992 wird der Betreiber darauf aufmerksam gemacht,

daß die von ihm mit diesem Gerät zusammengestellte

Anlage auch den technischen Bestimmungen dieser

Amtsblätter genügen muß.

For the customers in the United Kingdom

WARNING

THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance

with the following code:

Green-and-yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed

as follows:

The wire which is coloured green-and-yellow must be

connected to the terminal in the plug which is marked

by the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or

coloured black.

The wire which is coloured brown must be connected

to the terminal which is marked with the letter L or

coloured red.

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to

qualified personnel only.

For the customers in the USA

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference when the equipment is operated in a

commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your

authority to operate this equipment.

The shielded interface cable recommended in this

manual must be used with this equipment in order to

comply with the limits for a digital device pursuant to

Subpart B of Part 15 of FCC Rules.

WARNING

If used in USA, use the UL LISTED power cord specified

below. DO NOT USE ANY OTHER POWER CORD.

Plug Cap Parallel blade with ground pin

(NEMA 5-15P Configuration)

Cord Type SJT, three 16 or 18 AWG wires

Length Less than 2.5 m (8 ft 3 in)

Rating Minimum 10 A, 125 V

Using this unit at a voltage other than 120 V may require

the use of a different line cord or attachment plug, or

both. To reduce the risk of fire or electric shock, refer

servicing to qualified service personnel.

For the customers in Canada

This apparatus complies with the Class A limits for radio

noise emissions set out in Radio Interference

Regulations.

Pour les utilisateurs au Canada

Cet appareil est conforme aux normes Classe A pour

bruits radioélectriques, spécifiés dans le Règlement sur

le brouillage radioélectrique.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

The DVS-2000C Digital Video Switcher System is made

up of the DVS-2000C Video Switcher, which forms the

processor component, and the BKDS-2010 Switcher

Control Panel. The following manuals are necessary to

operate these two units.

DVS-2000C Installation Manual

(This manual, supplied with the switcher)

Section 1, “Operation” gives an overview of the BVS-

2000C system and optional accessories, explains the

function of parts for the switcher, and gives connection

examples. Persons responsible for management of the

system are required to read this section first. The second

and following sections contain information needed for

installation.

DVS-2000C Maintenance Manual Part 1

(Supplied with the switcher)

Contains information needed for periodic maintenance.

Read this manual when maintenance is necessary, or

when trouble develops.

BZS-2020 User’s Guide

(Supplied with operation software)

Explains operation procedures and function of each part

of the control panel. Read this manual before operating

the control panel.

BKDS-2010 Maintenance Manual

Contains information about the hardware of the control

panel.

DVS-2000C Maintenance Manual Part 2

Contains information about the hardware of the proces-

sor.

About the Manuals for the DVS-2000C Digital Video Switcher

Optional Accessories for ver. 1.10 operation software

For a DVS-2000C with ver. 1.10 or later operation

software, use the following optional accessories.

BKDS-2010/1 Switcher Control Panel (Serial No.

20001 or higher)

Program memory has been expanded to 4 megabits from

the 1 megabits of the previous model. This manual uses

“BKDS-2010” to refer to both the BKDS-2010 (Serial

Nos. 10001 through 10140) and BKDS-2010/1. For the

DVS-2100C, you can use the BKDS-2010.

BKDS-2020A/2021A Serial Digital Input board

In addition to the functions provided by the BKDS-2020/

2021, supports input of depth key signals from the DME-

3000 and other units. This manual uses “BKDS-2020” to

refer to both the BKDS-2020 and BKDS-2020A, and

“BKDS-2021” to refer to both the BKDS-2021 and

BKDS-2021A.

BZS-2090A Memory Pack

The BZS-2090A allows you to store about 99 snapshots,

compared to the limit of about 25 snapshots for the BZS-

2090. However, the expanded memory is not available

unless you have installed the BKDS-2072 CPU Upgrade

Board in the DVS-2000C. This manual uses “BZS-2090”

to refer to both the BZS-2090 and the BZS-2090A.

TABLE OF CONTENTS

1. OPERATION .............................................1-1(E)

1-1 Overview of the DVS-6000/6000C....... 1-1(E)

1-1-1 Principal Features ......................... 1-1(E)

1-1-2 Optional Accessories .................... 1-3(E)

1-1-3 Peripheral Equipment

Configuration................................ 1-5(E)

1-1-4 Important Precautions ................... 1-7(E)

1-2 Location and Function of Parts ........... 1-8(E)

1-2-1 Front Panel and Interior................. 1-8(E)

1-2-2 Rear Panel ................................... 1-15(E)

1-2-3 BKDS-6010 Control

Panel (optional) rear panel .......... 1-19(E)

1-3 System Configuration Examples....... 1-20(E)

1-3-1 Control Panel Connections.......... 1-20(E)

1-3-2 Primary Input and Video Monitor

Connections ................................ 1-21(E)

1-3-3 External Chroma Key Source

Connections ................................ 1-22(E)

1-3-4 DME-5000 Digital Multi Effect

Connections ................................ 1-23(E)

1-3-5 BVE-9100 Editing Control System

Connections ................................ 1-24(E)

1-4 Specifications...................................... 1-25(E)

1-4-1 DVS-6000/6000C ....................... 1-25(E)

1-4-2 BKDS-6010 ................................ 1-30(E)

1-4-3 BKDS-8021 ................................ 1-31(E)

1-4-4 BKDS-8022 ................................ 1-32(E)

1-4-5 BKDS-8030 ................................ 1-32(E)

1-4-6 BKDS-8031 ................................ 1-33(E)

1-4-7 BKDS-8040 ................................ 1-33(E)

1-4-8 BKDS-8041 ................................ 1-33(E)

1-4-9 BKDS-6050 ................................ 1-34(E)

1-4-10 BKDS-6060 ................................ 1-34(E)

1-4-11 BKDS-6061 ................................ 1-35(E)

1-4-12 BKDS-6062 ................................ 1-35(E)

1-4-13 BKDS-6063 ................................ 1-36(E)

1-4-14 BKDS-6064 ................................ 1-36(E)

1-4-15 BKDS-6070 ................................ 1-37(E)

1-4-16 BKDS-6071 ................................ 1-37(E)

1-4-17 BKDS-6072 ................................ 1-38(E)

1-4-18 BKDS-6090 ................................ 1-38(E)

Section 1 OPERATION

1-1

Section 1 OPERATION

1) Flexi Pad is a trademark of Sony Corporation.

1-1 Overview of the DVS-2000C

The DVS-2000C Digital Video Switcher is a high-perfor-

mance digital switcher that enables broadcasting stations

and production houses to construct small-scale component

digital editing systems. It is also suited to use in ENG (elec-

tronic news gathering) and a wide variety of other applica-

tions. Most switcher operations are carried out using the op-

tional BKDS-2010 Switcher Control Panel. This section will

use the following terms for the components of the system.

Full name

Terms used in this manual

DVS-2000C Digital Video Switcher

BKDS-2010 Switcher Control Panel

Switcher

Control panel

™

1-1-1 Features

Low power consumption and compact size

Many switcher function have been realized in newly

developed VLSIs, for low power consumption and

compact size.

Easy-to-use control panel

The easy-to-use control panel, only 19 inches in width,

provides a simple and well-designed man/machine

interface, with features such as an LCD display and a

Flexi Pad™

High-performance, expandable I/O interface

Primary inputs can be expanded to 16 channels by

installing optional analog component input boards, or

serial digital input boards with active loop through

output. All input signals can be used as background, key

fill and key source. Each channel is provided with a TBC

(time base corrector) function, allowing you to adjust

signal phase and remove jitter. Video processing func-

tions are also provided for every channel, allowing you to

adjust the gain, offset, and chrominance of each input

signal.

1-2

Section 1 OPERATION

There are three program output channels and one edit

preview output channel (AUX4) as standard. An assign-

able output board is available to provide one channel of

analog component output and two channels of serial

digital output, each of which can be used independently.

An optional auxiliary output board is also available to

provide three AUX bus output channels.

High-definition, high-quality key effects

The switcher is equipped with two keyer channels,

expandable to three channels through installation of

optional DSK boards.

The keyers guarantee high-definition, high-quality key

effects through fine adjustment of key edge position on a

sub-clock basis (FineKey™

function) and

oversampling. An optional chroma key board provides

similar effects (FineChroma™

function). Optional

border generators are available for continuous adjustment

of borders, drop borders,

shadows, and outlines, using modifiers such as edging

color, position, width, hue and softness.

Newly developed VLSIs expand key signals to the word

length needed for internal processing, reducing

degradation in signal characteristics.

Variety of new functions

Dynamic priority control: Allows continuous

modification of KEY1 and KEY2 priority with the

fader lever and encoder knob.

Depth key processing: Allows exchange of depth key

signal with the DME-3000 or other digital multi

effects units.

Processed key output: Allows efficient exchange of

chroma key signals and key signals containing

modifier information with the DME-3000 or other

digital multi effects units.

DME-Link

®3)

: Allows control of both the switcher and

the DME-3000 or other digital multi effects units

from the control panel.

™

1) FineKey is a trademark of Sony Corporation.

2) FineChroma is a trademark of Sony Corporation.

3) DME-Link is a registered trademark of Sony Corporation.

Section 1 OPERATION

1-3

Section 1 OPERATION

•

ˆ ˆ

FineChroma: Installation of an optional chroma key

board provides the following functions.

• 4:4:4 input

• Oversampling

• Dual adjustment

• Color modification

• Shadow adjustment

• Exclusive mask generators

Optional functions

In addition to optional I/O interface boards, numerous

optional boards are available to increase the flexibility of

the system, including an enhanced wipe generator board

to provide heart, star, matrix and other wipe patterns, a

CPU upgrade board, and a frame memory board to store

key signals and video created with the system as well as

mask patterns created with the pen tablet. Optional

memory packs provide increased memory for storage of

switcher setup data and snapshot data.

Flexible system configuration

The setup menu allows you to configure the system by

switching between 525-line and 625-line modes, or

between 4:3 and 16:9 aspect ratios.

You can connect editing control system such as the BVE-

2000 and digital multi effects units using interface on the

rear panel. An optional CPU upgrade board is available to

provide an interface to external matrix switchers for

sophisticated editing operations. Standard connectors for

serial tally and terminal units allow you to connect a wide

variety of external devices as necessary.

Easy maintenance

The power supply, circuit boards, and other principal

components are accessible from the front of the cabinet,

for easy maintenance and shorter down time in the event

of a malfunction. The number of switches and controls

has been held to a minimum, using software control as far

as possible for circuit adjustments and settings. The

switcher is equipped with internal self-diagnostic func-

tions and supports Interactive Status Reporting (ISR),

providing a quick overview of the state of the switcher.

1-4

Section 1 OPERATION

1-1-2 Optional Accessories

BKDS-2010 Switcher Control Panel

Control panel for the DVS-2000C.

BZS-2020 Operation Software is needed to operate the

control panel.

BKDS-2020 6 Serial Digital Input Board

Provides input of D1 serial digital signals to the DVS-

2000C. Up to six channels of video or key signals can be

input. Each channel is equipped with functions for TBC,

video processing and active loop-through output. Up to

two BKDS-2020 boards can be installed in the switcher.

BKDS-2021 2 Serial Digital Input Board

Provides input of D1 serial digital signals to the DVS-

2000C. Up to two channels of video or key signals can be

input. Each channel is equipped with functions for TBC,

video processing and active loop-through output. One

BKDS-2021 board can be installed in the switcher

together with a BKDS-2022 Analog Component Input

Board.

BKDS-2022 Analog Component Input Board

Provides input of analog component signals to the DVS-

2000C. Up to two channels of video (Y/B–Y/R–Y) and

key (KEY) signals can be input. Each channel is

equipped with functions for TBC and video processing.

active loop-through output. Up to two BKDS-2022

boards can be installed in the switcher.

BKDS-2031 Chromakey Board

Provides chroma key functions for the DVS-2000C.

Supports 4:2:2 foreground and background chroma key

signals, and 4:4:4 (Y/B–Y/R–Y) foreground signals.

Also provides a video processing function.

Section 1 OPERATION

1-5

Section 1 OPERATION

BKDS-2032 Chromakey Upgrade Board

Enhances the chroma key functions provided by the

BKDS-2031 Chromakey Board. Supports input of 4:4:4

(Y/B–Y/R–Y) signals for both foreground and back-

ground, and provides dual adjustment, color modifica-

tion, and shadow adjustment functions. One BKDS-2032

board can be installed for one BKDS-2031 board.

BKDS-2041 Frame Memory Board

Provides 1 frame × 2 channels of frame memory for the

DVS-2000C to store video or key signals. Equipped with

an exclusive mask generator, a matte generator, and a pen

tablet interface.

BKDS-2050 DSK with Border/FineKey Board

Provides downstream keyer functions for the DVS-

2000C. Equipped with mask generator and border

functions as well as keying functions equivalent to KEY1

and KEY2.

BKDS-2060 Assignable Output Board

Provides assignable output channels for the DVS-2000C.

Supports two channels of serial digital output and one

channel of analog component output (Y/B–Y/R–Y). Both

channel can be used independently.

BKDS-2061 Aux Bus/Processed Key Output Board

Provides AUX bus and depthkey output for the DVS-

2000C. Supports three AUX bus channels, which can be

used for video or key/depth key output.

BKDS-2062 NTSC Black Burst Generator Board

Provides NTSC black burst signal output for the DVS-

2000C. The output is locked to the switcher’s reference

signal.

1-6

Section 1 OPERATION

BKDS-2070 Enhanced Wipe Generator

Provides functions to enhance the performance of the

DVS-2000C’s built-in wipe generator, including HV

modulation, enhanced wipe patterns (heart, matrix, and

so on), and pattern mixing functions.

BKDS-2071 ME Key Border/FineKey Board

Provides key border and FineKey functions to enhance

the DVS-2000C’s built-in KEY1 and KEY2 functions.

Supports modifiers such as border, drop border, drop

shadow, and outline.

BKDS-2072 CPU Upgrade Board

Expands snapshot memory and provides additional RS-

422A interfaces (MATRIX, EDITOR B, etc.).

BZS-2020 Operation Software with Manual

Operation software (ROM pack) for the switcher and

control panel. Supplied with special key tops and a User’s

Guide explaining how to use the control panel.

BZS-2090 Memory Pack

Provides increased memory to store setup data and

snapshots created with the switcher. Install in the BKDS-

2010 Control Panel to store switcher data and load data

from the memory pack into the switcher.

Section 1 OPERATION

1-7

Section 1 OPERATION

1-1-3 Peripheral Equipment Configuration

The following diagram shows the switcher and peripheral

equipment. The minimum possible configuration is

shown within the dotted lines.

DVS-2000C peripheral equipment configuration

MATTE

KEY

BUS

SELF AUTO

ENABLE

EDITOR

DME GPI

SETUP MEM MISC

SYSTEM

1 2 3

USER MENU

F1 F2 F3 F4 F5 F6 EXIT

NORM

REW

REV

WIPE

DIRECTION

MULTI

ROTA-

TION

MODIFY

BORD SOFT ASPCT

POS

COLOR

MIX

KEY

DSK

AUX BUSES

KEY CONTROL

LUM LIN CLEAN CHR

SPLIT

PTN

BORD

MAIN

MASK

DROP

BORD

SHDW

KEY

INV

2 3 4

FILL SOURCE

DELEGATION

EDGE

MODIFY

DELECTION

EDGE

KEY

DSK

FILL

WIPE

BORD

COLOR

BKGD

2ND

MATTE

UTILITY

AUTO

DSK

FTB

TRANS

RATE

WIPE

LEARN

RECALL

+ / –

EFF

DISS

CLEAR

AUTO

TRANS

TRIM

XPT

DSBL

USER

WIPE

•

ENTERDIRECT

SHIFT

KEY

SRCE

FRAME

MEM

AUX

EDIT

PVW

COLOR

BKGD

KEY

PRIOR

KEY 1

KEY 2

BKGD

KEY

MIX

WIPE

DME

BLACK

KEY BUSES

PGM BUS

PST BUS

COLOR

BKGD

COLOR

BKGD

COLOR

BKGD

OVER OVER

CUT

DSK

MIX

DSK

PVW

FADE

BLACK

KEY

DSK

559.99 99.99 –10.00 359.99 100.00 100.00

CK HUE GAIN CLIP HUE CHROMA LUM

AUTO

TRANS

NEXT TRANSITION

TRANSITION TYPE

OUT

LINE

MATTE

DIGITAL VIDEO SWITCHER DVS-2000C

1-8

Section 1 OPERATION

•

1-1-4 Usage and Handling Precautions

Handling of circuit boards

Do not remove circuit boards unless absolutely neces-

sary. When it is necessary to remove circuit boards for

maintenance or to install optional boards, observe the

following precautions.

• Be sure to turn the POWER switch off before inserting

orremoving a board.

For the location of the POWER switch, see next page.

• After installing a board, and before turning the

POWERswitch on, check to be sure that the slot

number printed on the interior of the switcher matches

the slot number printed on the board.

Note

Failure to observe these precautions may result in

damage to the switcher circuits.

Handling of ROM and memory packs

When handling the ROM and memory packs, take care

not to touch the connector edges. Do not disassemble or

subject to strong shocks.

Section 1 OPERATION

1-9

Section 1 OPERATION

1-2-1 Front Panel and Interior

1-2 Location and Function of Parts

Front panel

How to open the front panel

DIGITAL VIDEO SWITCHER DVS-2000C

POWER Indicator

POWER switch

Panel lock screw

DIGITAL VIDEO SWITCHER DVS-2000C

Loosen the panel lock screw with a screwdriver and pull open.

1-10

Section 1 OPERATION

Interior of front panel

1 POWER switch

Switch to turn the power on or off.

2 Circuit boards

Boards correspond to slot numbers as follows.

Slot numbers

Circuit boards

POWER switch

Section 1 OPERATION

1-11

Section 1 OPERATION

OUT-6 ASSIGNABLE OUTPUT BOARD

MY-66 FRAME MEMORY BOARD

RAM-16 CPU UPGRADE BOARD

SG-231 NTSC BLACK BURST

GENERATOR BOARD

WKG-12 ENHANCED WIPE BOARD

BD-25 ME KEY BORDER/FINEKEY

BOARD

DSK-11 DSK WITH BORDER/

FINEKEY BOARD

KPC-6 DSK WITH BORDER/FINEKEY

BOARD

CRK-10 CHROMAKEY BOARD

CRK-11 CHROMAKEY

UPGRADE BOARD

AXM-6 AUX BUS/PROCESSED KEY

OUTPUT BOARD

BKDS-2020

BKDS-2022

BKDS-2021

BKDS-2020

BKDS-2022

BKDS-2021

BKDS-2060

BKDS-2041

BKDS-2072

BKDS-2062

BKDS-2070

BKDS-2071

BKDS-2050 (1/2)

BKDS-2050 (2/2)

BKDS-2031

BKDS-2032

BKDS-2061

Slot number Pre-installed boards

/ Optional boards

/ Model name

/ Board name

DI-18 6 SERIAL DIGITAL INPUT BOARD

AD-98 ANALOG COMPONENT

INPUT BOARD

DI-19 2 SERIAL

DIGITAL INPUT BOARD

DI-18 6 SERIAL DIGITAL INPUT BOARD

AD-98 ANALOG COMPONENT INPUT

BOARD

DI-19 2 SERIAL DIGITAL

INPUT BOARD

IO-92 DIGITAL INPUT/

OUTPUT BOARD

XPT-5 CROSS POINT

BOARD

CPU-156 CPU/SYNC

GENERATOR/CROSS

POINT BOARD

MIX-19 MIXER

BOARD

1-12

Section 1 OPERATION

GND

5V5V

ABORT

RESET

RESET HALT

CPU-156

CHARGE

DBG

DBG switches

–5V TEST

–5V TEST connector

+3V TEST

+3V TEST connector

+5V TEST

+5V TEST connector

TERMINAL

TERMINAL connector

!º



GND TEST

GND TEST connector

!¡



–5V

–5V indicator

!™



+3V

+3V indicator

!£



+5V

+5V indicator

!¢

CHARGE

CHARGE indicator

RESET

RESET indicator

HALT

HALT indicator

RESET

RESET switch

ABORT

ABORT switch

Section 1 OPERATION

1-13

Section 1 OPERATION

INT indicator

CON indicator

!⁄

TALLY indicator

!ƒ

DME indicator

!¥

EDTA indicator

!»

EDTB indicator

@…

MTX indicator

@“

FRAME MEMORY

BOARD connector

REF IN

REF ERR

625 / 525

REF OUT

STS4

STS3

STS2

STS1

MTX

EDTB

EDTA

DME

TALLY

CON

INT

TO FRAME MEMORY

D/A clock phase control switch

@ƒ

D/A clock select switches

@¥

D/A input connector

@»

D/A output connector

#…

REF IN indicator

REF ERR indicator

#“

625/525 indicator

#£

REF OUT BB indicator

#¢

@£

@¢

@⁄

STATUS indicators

ページが読み込まれています...

Sony BKDS-2010 インストールガイド

ブランド: Sony

モデル: BKDS-2010

カテゴリー: ビデオコンバーター

タイプ: インストールガイド

PDFをダウンロードします

報告

他の言語で

English: Sony BKDS-2010 Installation guide

Sony BKDS-2010 インストールガイド

Sony BKDS-2010 インストールガイド

他の言語で

関連論文

その他のドキュメント