TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 1 -
Quick Start Version 1.0
1 Shipping package
Thanks for buying ICPDAS TPD 2.8 inch H series device. This shipping package contains the
following items:
TPD-280-H/280U-H Quick Start (This Document)
2 Appearance
Front View TPD-280U-H Rear View TPD-280-H Rear View
2.8” TFT LCD with Touch Panel
USB
Rotary Switch
TPD-280-H/280U-H
RS-485
RS-485
Rotary Switch
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 2 -
3 Pin Assignment
On the back of the TPD-280-H/280U-H:
The pin assignments:
No
Pin
Description
0
F.G.
Frame Ground. F.G. is connected to the inside EMI or ESD suppression
circuits. Make sure that F.G. is connected to the Earth
1
VDC
DC input Voltage (range: +12 V ~ +48 V)
2
GND
Connected to the power supply’s ground pin
3
Data+
The positive data line of the RS-485 network
4
Data-
The negative data line of the RS-485 network
The definition of the rotary switch (TPD-280-H):
No
Mode
Description
0
Run Only
Run the program.
1
Update
Only
Update the program via RS-485.
The definition of the rotary switch (TPD-280U-H):
No
Mode
Description
0
Run Only
Run the program.
9
USB Force
Update
Update a new application to the TouchPAD device
through USB.
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 3 -
4 First Use of the TPD-280(U)-H
1. Connect wires as the figure. And set the rotary switch
to zero (At this point, the power is not yet supplied).
2. Supply power to the TPD-280-H/280U-H, wait for several seconds
and then you can see the default program run on it.
3. Try to touch on the icons on the bottom-right corner of the screen
of the TPD-280-H/280U-H and you can find that
TPD-280-H/280U-H switches to the setting pages.
5 Creating First Project
To create your first project of the TPD-280-H/280U-H, install the free development tool,
HMIWorks and then refer to <<TouchPAD_getting_started.pdf>>, which can be found on the
FTP: http://ftp.icpdas.com/pub/cd/touchpad/document/english/programming_guide/
GND
VDC (+12~+48V)
Use a flat-head screwdriver to
set rotary switch
External Power
GND
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 4 -
6 Hardware Installation
7 Related Information
TPD-280-H/280U-H Product Page:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tpd-280-h.html
Documents, such as the user manuals, the API references, etc.:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
Free Development Software, HMIWorks v2.10.10 or above:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email at:
service@icpdas.com, service.icpda[email protected]
External Wall Box, EWB-T28 (optional)
Outlet Box, OB120 (optional)
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 5 -
快速入門指南 版本 1.0
1 檢查配件
感謝您購買泓格的 TPD 2.8 吋 H 系列產品。產品包裝內應包含下列配件:
TPD-280-H/280U-H 產品須知 (本文件)
2 外觀
前配置圖 TPD-280U-H 後配置圖 TPD-280-H 後配置圖
2.8 吋觸控液晶螢幕
旋轉開關
TPD-280-H/280U-H
USB
RS-485
RS-485
旋轉開關
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 6 -
3 腳位定義
在 TPD-280-H/280U-H 的背面可見到如下圖樣:
腳位定義:
No
Pin
說明
0
F.G.
機架接地，F.G. (連接到內部的 EMI 或 ESD 保護電路)，請接到大地。
1
VDC
直流電壓輸入 (範圍：+12 V ~ +48 V)
2
GND
連到電源的接地端
3
Data+
RS-485 網路的正訊號線
4
Data-
RS-485 網路的負訊號線
旋轉開關 (Rotary Switch) 的配置模式定義 (TPD-280-H):
項次
模式
說明
0
Run Only
執行程式。
1
Force Update
透過 RS-485 更新程式。
旋轉開關 (Rotary Switch) 的配置模式定義 (TPD-280U-H):
項次
模式
說明
0
Run Only
執行程式。
9
USB Force
Update
透過 USB 更新程式。
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 7 -
4 第一次使用 TPD-280(U)-H 系列
1. 如左圖所示，將電源和接地線連接完成。然後將
旋轉開關(Rotary Switch)轉到 0(此時尚未供電)。
2. 開始供電給 TPD-280-H/280U-H，等待約數秒的開機時間，接著
可以看到 TPD-280-H/280U-H 執行出貨預附的程式如圖所示。
3. 試著按一下 TPD-280-H/280U-H 螢幕上面的圖示，
TPD-280-H/280U-H 會切到其他的頁面。
5 建立第一個軟體專案
在建立 TPD-280-H/280U-H 的第一個專案之前，請先安裝免費的開發軟體 HMIWorks。然
後參考<< TouchPAD_getting_started.pdf>>這份文件，一步一步地完成。該份文件可
以在 FTP 上找到：
http://ftp.icpdas.com/pub/cd/touchpad/document/chinese/programming_guide/
使用一字起子來配置旋轉開關
GND
VDC (+12~+48V)
外部供電器
GND
TPD-280-H/280U-H Quick Start, version 1.0 Last Revised: April 2017 - 8 -
6 硬體安裝
7 參考資訊
TPD-280-H/280U-H 產品網頁:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tpd-280-h_tc.html
相關文件，如使用手冊、API 函數手冊…等:
http://ftp.icpdas.com/pub/cd/touchpad/document/chinese/
免費開發軟體，HMIWorks 版本 2.10.10 或以上版本:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎聯繫我們，我們將會為您提供完善的咨詢服務:
E-mail: ser[email protected], service.icpda[email protected]
安裝於專用明盒 EWB-T28(選購)
安裝於專用暗盒 OB120 (選購)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
