ICP VPD-132N-H Quick Start

タイプ
Quick Start

このマニュアルも適しています

VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 1 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: se[email protected]
Quick Start Version 1.0
1 Shipping package
Thanks for buying ICPDAS VPD-130-H/132-H Series device. This shipping package contains
the following items:
VPD-130-H/132-H Series x 1 Quick Start x 1 Screw Driver x 1 Panel Mounting kit x 1
2 Appearance
LED Indicator
Serial Port
USB
Rotary Switch
VPD-130-H
VPD-132-H
VPD-130N-H
VPD-132N-H
VPD-130(N)-H/132(N)-H
Rubber Keypad
(for VPD-130-H/132-H only)
XV-Board
(optional)
or
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 2 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: se[email protected]
3 Pin Assignment
On the bottom of the TouchPAD:
VPD-130-H/130N-H VPD-132-H/132N-H
The pin assignments:
Pin
Description
F.G.
Frame Ground. F.G. is connected to the inside EMI or ESD suppression
circuits. Make sure that F.G. is connected to the Earth
VDC
DC input Voltage (range: +12 V ~ +48 V)
GND
Connected to the power supplys ground pin
GND
Ground pin
D1-
The negative data line of the RS-485 network
D1+
The positive data line of the RS-485 network
TxD1
The pin of transmitted data of the RS-232
RxD1
The pin of received data of the RS-232
GND
The common ground of the RS-232
D2-
The negative data line of the RS-485 network (for VPD-132(N)-H only)
D2+
The positive data line of the RS-485 network (for VPD-132(N)-H only)
The definition of the rotary switch:
No
Mode
Description
0
Run Only
This mode is used for running programs.
9
USB Update
Update a new application to the TouchPAD device
through USB.
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 3 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
4 First Use of the VPD-130/132-H
1. Connect wires as the figure and set the rotary switch
to zero. (At this point, the power is not yet supplied)
2. Supply power to the VPD-130(N)-H/132(N)-H, wait for several
seconds and then you can see the default program run on it.
3. Try to touch on the icons on the bottom-right corner of the
screen of the VPD-130(N)-H/132(N)-H and you can find that
VPD-130(N)-H/132(N)-H switches to the setting pages.
5 Creating First Project
To create your first project of the VPD-130(N)-H/132(N)-H, install the free development tool,
HMIWorks and then refer to <<TouchPAD_programming_quide.pdf>>, which can be found
on the FTP:
http://ftp.icpdas.com/pub/cd/touchpad/document/english/programming_guide/
Use a flat-head screwdriver to
set rotary switch
GND
VDC (+12~+48V)
External Power
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 4 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
6 Hardware Installation
The panel mounting of VPD-130(N)-H/132(N)-H
The DIN-rail Mounting of VPD-130(N)-H/132(N)-H
7 Related Information
VPD-130(N)-H/132(N)-H Product Page:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/vpd-130-h.html
Documents, such as the user manuals, the API references, etc.:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
Free Development Software, HMIWorks v2.10.10 or above:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email at:
service@icpdas.com, servi[email protected]
Insert the panel mounting clips into
the upper and lower ventilation
holes.
Screw the panel mounting clips to the
panel. (Mounting Screw: M4 x 30L)
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 5 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
快速入門指南 版本 1.0
1 檢查配件
感謝您購買泓格的 VPD-130(N)-H/132(N)-H 產品。產品包裝內應包含下列配件:
VPD-130-H/132-H 系列 x 1 入門指南(本文件) x 1 螺絲刀 x 1 面板安裝組 x 1
2 外觀
LED 指示燈
重啟按鈕
序列埠
旋轉開關
USB
橡膠鍵盤
(VPD-130-H/132-H 僅有)
I/O 擴充卡
XV-Board (選購品)
VPD-130(N)-H/132(N)-H
VPD-130-H
VPD-132-H
VPD-130N-H
VPD-132N-H
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 6 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
3 腳位定義
VPD-130(N)-H/132(N)-H 下方,可見到如下圖序列埠:
VPD-130-H/130N-H VPD-132-H/132N-H
腳位定義:
Pin
說明
F.G.
機架接地,F.G. (連接到內部的 EMI ESD 保護電路),請接到大地。
VDC
直流電壓輸入 (範圍:+12 V ~ +48 V)
GND
連到電源的接地端
GND
接地端
D1-
RS-485 網路的負訊號線
D1+
RS-485 網路的正訊號線
TxD1
RS-232 的傳送資料腳
RxD1
RS-232 的接收資料腳
GND
RS-232 的接地端
D2-
RS-485 網路的負訊號 ( VPD-132(N)-H 僅有)
D2+
RS-485 網路的正訊號 ( VPD-132(N)-H 僅有)
旋轉開關 (Rotary Switch) 的配置模式定義:
項次
模式
說明
0
Run Only
執行程式 (只能執行程式不能進行更新)
9
USB Force Update
透過 USB 更新程式。
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 7 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
4 第一次使用 VPD-130/132-H
1. 如左圖所示,將電源和接地線連接完成。然後將旋轉開
(Rotary Switch)轉到 0(此時尚未供電)
2. 開始供電給 VPD-130(N)-H/132(N)-H待約數秒的開機時
接著可以看到 VPD-130(N)-H/132(N)-H 執行出貨預附的程式如
圖所示。
3. 試著按一下 VPD-130(N)-H/132(N)-H 螢幕上面的圖示,
VPD-130(N)-H/132(N)-H 會切到其他的頁面。
5 建立第一個軟體專案
在建立 VPD-130(N)-H/132(N)-H 的第一個專案之前,請先安裝免費的開發軟體 HMIWorks。然
後參考<< TouchPAD_programming_guide.pdf>>這份文件,一步一步地完成。該份文件可以在
FTP 上找到:http://ftp.icpdas.com/pub/cd/touchpad/document/chinese/programming_guide/
使用一字起子來
置旋轉開關
GND
VDC (+12 ~ +48V)
外部供電器
VPD-130(N)-H/132(N)-H Quick Start, version 1.0 Last Revised: May 2017 - 8 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
6 硬體安裝
VPD-130(N)-H/132(N)-H 的面板安裝(Panel Mounting)
VPD-130(N)-H /132(N)-H 導軌安裝(DIN-rail Mounting)
7 參考資訊
VPD-130(N)-H/132(N)-H 產品網頁:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/vpd-130-h_tc.html
相關文件,如使用手冊、API 函數手冊…:
http://ftp.icpdas.com/pub/cd/touchpad/document/chinese/
免費開發軟體,HMIWorks 版本 2.10.10 或以上版本:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎聯繫我們,我們將會為您提供完善的咨詢服:
E-mail: service@icpdas.com, servi[email protected]
於上下方的通風口,
插入面板固定鋁
使用 M4 x 30L 螺絲釘,
鎖緊固定面板及鋁夾
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ICP VPD-132N-H Quick Start

タイプ
Quick Start
このマニュアルも適しています

他の言語で