ICP TPD-433-M2 Quick Start

タイプ
Quick Start
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 1 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
TPD-433-M2
Quick Start Version 1.0
1 Shipping package
Thanks for buying ICPDAS TPD-433-M2 device. This shipping package contains the following items:
TPD-433-M2 x1 Quick Start x1 Back Piece x1 Round Head Screws x2
2 Appearance
Front View Rear View
Serial Port
USB
Rotary Switch
Ethernet
4.3 TFT LCD with Touch Panel
LED
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 2 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
3 Pin Assignment
On the back of the TouchPAD:
The pin assignments:
Pin
Description
Frame Ground. F.G. is connected to the inside EMI or ESD suppression circuits.
Make sure that F.G. is connected to the Earth
DC input Voltage (range: +12 V ~ +48 V)
Connected to the power supplys ground pin
The positive data line of the RS-485 network
The negative data line of the RS-485 network
Ground pin
The pin of transmitted data of the RS-232
The pin of received data of the RS-232
The definition of the rotary switch:
No
Mode
Description
0
Run &
Update
(Ethernet)
This is a special run mode which is used in the development
stage. The TouchPAD device can be updated by a PC from the
remote side through Ethernet.
1
Ethernet
Force
Update
While the application run on the TouchPAD device seriously
crashes, use this mode to update a new application to the
TouchPAD device through Ethernet.
2
Run Only
Run the program.
9
USB Force
Update
Update a new application to the TouchPAD device through
USB.
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 3 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om
4 First Use of the TPD-433-M2
1. Connect wires as the figure. External Power can be removed
if you have a PoE Switch providing power through an Ethernet
cable to the TouchPAD. And set the rotary switch to zero (At this
point, the power is not yet supplied).
2. Supply power to the TPD-433-M2, wait for several
seconds and then you can see the default program run
on it.
3. Try to touch on the icons on the screen of the
TPD-433-M2 and you can find that TPD-433-M2
switches to another page.
5 Creating First Project
To create your first project of the TPD-433-M2, install the free development tool, HMIWorks and
then refer to <<TouchPAD_programming _guide.pdf>>, which can be found on the FTP:
http://ftp.icpdas.com/pub/cd/touchpad/document/english/programming_guide/
Use a flat-head screwdriver to
set rotary switch
PoE Switch
External Power
GND
VDC (+12~+48V)
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 4 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
6 Related Information
TPD-433-M2 Product Page:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tpd-433-mx.html
Documents, such as the user manuals, the API references, etc.:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
Free Development Software, HMIWorks v2.10.24 or above:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email at:
service@icpdas.com, ser[email protected]
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 5 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
TPD-433-M2
快速入門指南 版本 1.0
1 檢查配件
感謝您購買泓格的 TPD-433-M2 產品。產品包裝內應包含下列配件:
TPD-433-M2 x1 快速入門指 x1 固定座 x1 圓頭螺絲 x2
2 外觀
前配置圖 後配置圖
LED
Ethernet
4.3 吋觸控液晶螢幕
序列埠
USB
旋轉開關
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 6 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
3 腳位定義
TouchPAD 背面可見到如下圖樣:
腳位定義:
Pin
說明
機架接地,F.G. (連接到內部的 EMI ESD 保護電),請接到大地。
直流電壓輸入 (範圍:+12 V ~ +48 V)
連到電源的接地端
RS-485 網路的正訊號
RS-485 網路的負訊號
接地端
RS-232 的傳送資料腳
RS-232 的接收資料腳
旋轉開關 (Rotary Switch) 的配置模式定義:
項次
模式
說明
0
Run & Update
(Ethernet)
執行/更新程式,用於程式開發階段 (能執行程
也能進行更新)通過乙太網路可進行遠端更
新程式。
1
Ethernet Force
Update
強制更新,當程式嚴重毀損時可用此模式透過
Ethernet 更新。
2
Run Only
執行程式 (只能執行程式,不能進行更新)
9
USB Force Update
透過 USB 更新程式
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 7 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
4 第一次使用 TPD-433-M2
1. 如左圖所示,將電源和接地線連接完成。若您使用 PoE
Switch 透過網路線 TouchPAD 供電則可省略外部供電器。
然後將旋轉開關(Rotary Switch)轉到 0(此時尚未供電)
2. 開始供電給 TPD-433-M2,等待約數秒的開機時間,
接著可以看到 TPD-433-M2 執行出貨預附的程式如圖
所示。
3. 試著按一下 TPD-433-M2 螢幕上面的圖示,
TPD-433-M2 會切到其他的頁面。
5 建立第一個軟體專案
在建立 TPD-433-M2 的第一個專案之前,請先安裝免費的開發軟體 HMIWorks。然後參考<<
TouchPAD_programming_guide.pdf>>這份文件,一步一步地完成。該份文件可以在 FTP 上找
到:
http://ftp.icpdas.com/pub/cd/touchpad/document/chinese/programming_guide/
使用一字起子來配
置旋轉開關
外部供電器
GND
VDC (+12~+48V)
乙太網路供電
TPD-433-M2 Quick Start, version 1.0 Last Revised: Apr. 2018 - 8 -
Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
6 參考資訊
TPD-433-M2 產品網頁:
http://www.icpdas.com/root/product/solutions/hmi_touch_monitor/touchpad/tpd-433-mx_tc.html
相關文件,如使用手冊、API 函數手冊…:
ftp://ftp.icpdas.com/pub/cd/touchpad/document/english/
免費開發軟體,HMIWorks 版本 2.10.24 或以上版:
ftp://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎聯繫我們,我們將會為您提供完善的咨詢服:
E-mail: service@icpdas.com, ser[email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ICP TPD-433-M2 Quick Start

タイプ
Quick Start

他の言語で