Korg PANDORA PX5D 取扱説明書

1

E

F

G

J

Manuel d’utilisation

Bedienungsanleitung

Owner’s manual

2

Precautions

Location

Using the unit in the following locations can result in a

malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

• Close to magnetic fields

Power supply

Please connect the designated AC adapter to an AC

outlet of the correct voltage. Do not connect it to an AC

outlet of voltage other than that for which your unit is

intended.

Interference with other electrical devices

Radios and televisions placed nearby may experience

reception interference. Operate this unit at a suitable

distance from radios and televisions.

Handling

To avoid breakage, do not apply excessive force to the

switches or controls.

Care

If the exterior becomes dirty, wipe it with a clean, dry

cloth. Do not use liquid cleaners such as benzene or

thinner, or cleaning compounds or flammable polish-

es.

Keep this manual

After reading this manual, please keep it for later refer-

ence.

Keeping foreign matter out of your equipment

Never set any container with liquid in it near this equip-

ment. If liquid gets into the equipment, it could cause a

breakdown, fire, or electrical shock.

Be careful not to let metal objects get into the equip-

ment. If something does slip into the equipment, un-

plug the AC adapter from the wall outlet. Then contact

your nearest Korg dealer or the store where the equip-

ment was purchased.

3

THE FCC REGULATION WARNING (for USA)

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful inter-

ference in a residential installation. This equipment gen-

erates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to ra-

dio or television reception, which can be determined

by turning the equipment off and on, the user is en-

couraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV tech-

nician for help.

Unauthorized changes or modification to this sys-

tem can void the user’s authority to operate this equip-

ment.

Notice regarding disposal (for EU)

If this “crossed-out trash can” symbol is shown

on the product or in the operating manual, you

must dispose of the product in an appropriate

way. Do not dispose of this product along with

your household trash. By disposing of this prod-

uct correctly, you can avoid environmental harm

or health risk. The correct method of disposal

will depend on your locality, so please contact

the appropriate local authorities for details.

* Company names, product names, and names of formats

etc. are the trademarks or registered trademarks of their

respective owners.

4

Table of Contents

Play mode ..............................................16

Selecting a program ................................................16

PROGRAM MEMORY [A], [B], [C], [D] buttons ......... 16

Using foot switches to select programs ......................... 16

Master level ...............................................................16

Bypass/Mute ............................................................. 17

Tuner ........................................................................... 17

Specifying the function of the Value encoder .. 18

Key Lock function ................................................... 18

Rhythm & Bass mode ..............................19

PTN (Pattern play) ................................................... 19

CHAIN (Chain play) ...............................................21

SONG (Song play)................................................... 23

Phrase Trainer mode ...............................25

Select the recording mode ..................................... 25

Recording .................................................................. 26

Playback ..................................................................... 27

Pause ........................................................................... 27

Saving ......................................................................... 27

Precautions ............................................... 2

Introduction ..............................................6

Main features ........................................... 6

Turning on the power ................................ 7

Controls and connectors ............................ 8

LCD screen ................................................................ 10

Making connections ................................ 11

Connecting to your Computer .............................. 13

Using the editor software ............................................... 13

Transferring audio data .................................................. 13

Initial Settings .........................................15

Quick Edit ................................................................. 15

5

Edit mode ............................................... 28

Select the effect that you wish to edit................. 28

Editing each effect ................................................... 28

DYNA: Dynamics & Pickup Modeling ......................... 28

AMP: Amp Modeling ...................................................... 29

CAB: Cabinet Modeling .................................................. 29

MOD: Modulation & Filter Effect Modeling ................ 30

DLY: Delay Modeling ...................................................... 30

DLY: Delay Time .............................................................. 30

REV: Reverb Modeling .................................................... 30

NR: Noise reduction ........................................................ 31

RENAME .......................................................................... 31

WRITE ............................................................................... 31

Utility mode ............................................ 32

Select a utility function .......................................... 32

Change settings for each utility function .......... 32

BACKLIGHT: LCD backlight on/off ............................ 32

KEY-TRN: Key transpose ................................................ 32

KTR+BC: Key transpose + bass cancel .......................... 33

AMP/LIN: Amp/line select ........................................... 33

FOOTSW: Foot switch pedal settings............................ 34

USBSEND: USB Send ...................................................... 35

USB RCV: USB Receive ................................................... 35

AUX>USB: USB audio interface .................................... 35

MIDDRUM: MIDI Drum/Bass ...................................... 36

Loading the factory-set data ................... 36

Effect Parameter List ...............................37

DYNA: Dynamics & Pickup modeling ............... 37

AMP: Amp Modeling ............................................. 39

CAB: Cabinet modeling ......................................... 43

MOD: Modulation & Filter Effect Modeling .... 45

DLY: Delay Modeling ............................................. 49

REV: Reverb Modeling ........................................... 50

Preset Program Names ........................... 51

Rhythm Pattern List ................................. 52

Troubleshooting ......................................53

Specifications.......................................... 55

6

Introduction

Thank you for purchasing the KORG PANDORA PX5D

personal multi-effect processor. In order to enjoy your

PANDORA PX5D, please read this owner’s manual care-

fully and retain it for future reference.

Main features

The PX5D is a versatile multi-effect unit that packs an

incredible range of guitar amps, bass amps and effects

into a compact unit which utilizes Korg’s proprietary

“

” modeling technology to create detailed and

powerful modeling sounds.

180 types of effect variations with a maximum of seven

effects that can be used simultaneously.

IPE (Integrated Parameter Edit) allows effects to be

quickly edited.

100 user and 100 preset programs

Control dials

The PX5D includes 18 types of guitar amp models, 10

types of bass amp models, and 6 type of synths, each of

which can be edited quickly and easily.

Backlit LCD

The large LCD screen can be easily viewed even in dark

locations.

Auto Tuner function

This feature makes tuning fast and easy. You can also

tune without being heard (i.e., while muted).

Rhythm and Bass function

128 types of rhythm and bass patterns or a metronome

can be used. 16 multiple patterns can also be connected

for successive playback.

Phrase Trainer function

You can use Rhythm & Bass mode to specify a rhythm

pattern, play along with this rhythm pattern from an au-

dio source connected to the AUX jack or USB connector

or on your guitar (or bass) connected to the INPUT jack

while you record the result, and then play back the re-

cording as a loop (maximum of approximately 80 sec-

onds). The playback speed can also be slowed down

without affecting the pitch of the audio. The rhythm se-

lected in Rhythm & Bass mode and the effect output can

also be recorded simultaneously.

AUX pitch function

This lets you modify the pitch of audio from the AUX

jack or USB connector (Key Transpose function) or can-

cel the low-frequency region (Bass Cancel function).

TAP/BYPASS button

You can easily set the Delay Time or the tempo of the

Rhythm & Bass function to match the tempo of the song.

7

Value encoder

This lets you rapidly select programs or edit the effects.

USB-MIDI, USB audio interface function

If you use the included USB cable to connect the PX5D

to your computer, you’ll be able to use the editor soft-

ware* to edit the PX5D or transfer audio data between

the PX5D and your computer.

*: You can download the editor software from the Korg

website (http://www.korg.com/). Expected to become

available in October, 2007.

What is

?

(Resonant structure and Electronic circuit

Modeling System) is KORG’s proprietary sound

modeling technology which precisely reproduces the

complex character and nature of both acoustic and

electric instruments as well as electronic circuits in

real world environments.

emulates a wide

variety of sound generation characteristics including

instrument bodies, speakers & cabinets, acoustic

fields, microphones, vacuum tubes, transistors, etc.

Turning on the power

Remove the battery cover located on the bottom of the

PX5D by sliding it in the direction of the arrow. Insert

two AA alkaline batteries as shown in the illustration. Be

sure to insert the batteries observing the correct polarity.

Battery Low display

When the battery begins to run low, the Low Battery icon

will light. When this icon lights, replace the batter-

ies as soon as possible. Programs and other data (except

for the data being edited) will not be lost even if the bat-

tery is removed and changed.

Batteries that have run down must be removed from the

PX5D. If you leave dead batteries in the unit, malfunc-

tions (battery leakage, etc.) may occur. You should also

remove the batteries when you do not expect to use the

PX5D for an extended period of time.

An AC adapter is not included with this product. It must

be purchased separately.

8

Controls and connectors

4

8

9

10

11

12

13

14

15

16

17

18

19

1

3

5 26

7

1. INPUT jack

Connect your guitar or bass to this jack.

2. AUX jack (stereo)

Connect this jack to a CD player or other audio source.

3. INPUT switch

Use this to adjust the input level depending on the out-

put level of your guitar or bass (☞p.15).

4. Control dials

These dials control the gain, tone, and volume of the amp

models and synth parameters.

5. Power switch

This switch turns the power on/off.

STANDBY: The power is off.

ON: The power is on.

USB: The power is on. When the PX5D is connected to

your computer via the USB cable, your computer will

supply power via the USB bus.

Some computers may not be able to supply power via USB

bus power. In this case, use a self-powered USB hub (that

obtains power from an external supply), use two batter-

ies, or use the AC adaptor.

6. FOOT SW jack

You can use the included cable for FOOT SW jack to con-

nect two foot switches.

7. OUTPUT jack

Connect this jack to your guitar amp, bass amp, or head-

phones etc.

8. LCD (Liquid Crystal Display)

(☞p.10 “LCD screen”)

9. CURSOR

Use these buttons to select programs or the parameter

that you wish to edit. These will also operate the Phrase

Trainer function.

9

10. DC4.5V

The separately sold AC adapter (DC4.5V

) is con-

nected here.

11. RHYTHM button

Use this button to enter Rhythm & Bass mode (☞p.19).

12. PHRASE TRAINER button

Use this button to enter Phrase Trainer mode (☞p.25).

13. UTILITY button

Use this button to enter Utility mode (☞p.32).

14. PROGRAM MEMORY [A] [B] [C] [D] buttons

You can assign your favorite programs to these four but-

tons (A–D) (☞p.16).

15. ENTER/REC button

This button is used to switch an effect on/off, to edit

patterns in Rhythm & Bass mode, or to start recording

in Phrase Trainer mode.

16. EXIT button

Returns to Play mode or to the preceding screen.

17. TAP/BYPASS button

In Edit mode this button lets you specify the delay time

for delay effects (☞p.15), or the rhythm tempo for rhythm

& bass mode (☞p.19). In Play mode, this button will By-

pass or Mute the PX5D, and activate the Tuner (☞p.17).

18. USB connector

Use the included USB cable to connect this to your com-

puter. You’ll be able to use the editor software to edit the

PX5D or transfer audio data between the PX5D and your

computer.

19. Value encoder

Use this to adjust the master level, edit effects, and se-

lect programs.

10

LCD screen

1

2

3

4

5

6

7

8

9

1. Effect chain

This area indicates the on/off status of the DYNA, AMP,

CAB, MOD, DLY, and REV effects.

2. Program name/Effect type display

This area shows the program name or effect type. When

the PX5D is bypassed or muted, this will function as the

tuner.

3. USB icon

This is shown if the PX5D is connected to your comput-

er via the USB port.

4. Low Battery icon

This icon will light when the batteries run low.

5. Mode icons

These are shown when you enter the corresponding

mode.

6. Program number/value display

This displays the program number. When you change

the Master Level, its value will be displayed here for sev-

eral seconds. During editing, this displays the parame-

ter values.

7. ORIG (Original) icon

If the parameter or value being edited matches the value

that is written in the program, the ORIG icon will light.

8. Bar graph

In Play mode or Edit mode, this graph indicates the mas-

ter level or the value of a parameter. In Rhythm mode,

this indication will change according to the rhythm pat-

tern that’s playing.

9. Variation icons (VARI1, VARI2)

This shows the variation of the rhythm pattern or rhythm

& bass pattern you’re using in Rhythm mode (☞p.20).

11

Making connections

When connecting an external device (ie-guitar amp, bass amp, CD player, AC adapter, etc.) be sure to turn the unit

off.

*3

*6

*7

headphone*4

mini-component /

stereo etc.

guitar amp /bass amp/

powered monitor

CD player etc.*2

guitar or bass

AC adapter *1

Computer

Digital recorder

Foot switch *5

12

*1 Be sure to use only the specified AC adapter (DC4.5V

).

*2 If a CD player or other audio source is connected to

the AUX jack, you can play along with your guitar or

bass. However the volume must be adjusted from the

connected device.

Connecting cables are sold separately.

*3 The PX5D’s output jack is stereo. If you use a mono

cable to connect it to a guitar or bass amp etc., only

the L (left) output will be heard.

*4 The PX5D’s output level and sound quality will vary

depending on which headphones are used. We rec-

ommend using good quality low impedance head-

phones, 32 Ohms or less with a sensitivity rating near

100dB/mW or above. Many headphones sold for use

with portable CD or cassette players will work fine.

*5

Use the included cable for FOOT SW jack to connect

two foot switches to the PX5D. You can connect two

foot switches such as the Korg PS-1 (sold separately).

In Utility mode you can specify the function of the

pedal switches; for example you can use them to

switch programs, or to start/stop recording and play-

back in Phrase Trainer mode (☞p.16 “Using foot

switches to select programs,” ☞p.34 “FOOTSW”).

*6 Use the included USB cable if you want to connect

the PX5D to your computer. For details on connec-

tions to your computer, refer to “Connecting to your

computer.”

*7 If needed, you can attach the included rubber feet to

the bottom of the PX5D.

13

Connecting to your Computer

If you use the included USB cable to connect the PX5D

to your computer, you’ll be able to use the editor soft-

ware to edit the PX5D, and transfer audio data between

the PX5D and your DAW software.

Using the editor software

The editor software lets you edit programs, manage data

libraries, and create chains for Rhythm & Bass mode.

You can download the editor software from the Korg web-

site (http://www.korg.com/). For details on installing and

using the editor software, refer to the owner’s manual.

In order to use the editor software, you’ll need to install

the KORG USB-MIDI driver into your computer. (“In-

stalling the software” in the included CD-ROM).

Transferring audio data

If you use a USB cable to connect the PX5D to your com-

puter, the PX5D’s effect output, the rhythm sounds of

Rhythm & Bass mode, and phrases you recorded in

Phrase Trainer mode can be recorded directly into audio

tracks of your DAW software. The playback of your DAW

software can also be monitored through the PX5D.

If you’re computer is running Windows XP, we recom-

mend that you install the KORG USB-ASIO driver (in

the included CD-ROM) into your computer if you want

to transfer audio using the USB connector. For details

on installing the KORG USB-ASIO driver, refer to “In-

stalling the software” on the included CD-ROM.

The following illustration shows the signal flow when

the PX5D is connected to your computer.

USB

OUTPUT

INPUT

Effect

Rhythem&Bass

Phrase Trainer

PX5D

The PX5D’s effect will not apply to the audio input via

the USB connector.

14

Adjust the master level setting to change the volume of

the audio signal that’s sent from the PX5D’s OUTPUT

jack (☞p.16 “Master level”).

Adjust the Utility mode “USBSEND” setting to change

the volume of the audio signal that’s sent from the

PX5D’s USB connector to the computer (☞p.35 “USB-

SEND”).

Adjust the Utility mode “USB RCV” setting to change

the volume of the audio signal that’s input from the com-

puter to the PX5D (☞p.35 “USB RCV”).

Normally, the signal that’s being input from the AUX

jack is not sent to the USB connector. If you want the

input signal from the AUX jack to be sent to your com-

puter, access the Utility mode “AUX > USB” screen

(☞p.35 “AUX>USB”).

If you’re recording the PX5D’s effect output onto an au-

dio track of your DAW software, turn off the “audio in

thru” function of your software to prevent echo-back.

For details on using your DAW software, refer to the op-

eration manual included with your software.

15

Initial Settings

1 When you finish making connections, set the power

switch to the “ON” position. (This setting is referred

to as Play mode.)

Use the π/† CURSOR to select a program.

2 Set the input level switch depending on the output

level of your guitar or bass.

HI: High-output pickups (e.g., humbucking or pick-

ups with a preamp)

LO: Low-output pickups (e.g., single-coil type pick-

ups)

3 Set the volume control of your guitar or bass to its

usual position. Use the Value encoder to adjust the

master level.

Quick Edit

In each mode (except when Mute/Bypass or Key Lock

are active), you can use the Control dials to adjust the

gain, tone, or volume of amp modeling. When you move

a control dial, the parameter name and value will appear

for several seconds in the value display. If the setting

matches the original setting, the ORIG icon will light.

The Delay Time can also be set by pressing the TAP/BY-

PASS button twice at the desired interval (except when

in Rhythm & Bass mode).

When you set the delay time, the value display will in-

dicate the delay time for several seconds.

Program

selection

Program

name

Input level switch

Amp gain, tone, and volume

Program

number

Set the

delay time

Master level

adjustment

Settings that you make using Quick Edit will return to

the original saved settings if you change programs or turn

off the power before Writing (☞p.31 “WRITE”).

16

Play mode

Play mode is the mode in which you will normally use

the PX5D.

Selecting a program

Use the π/† CURSOR to select a program. The pro-

gram/effect type display will show the program name,

and the value display will show the program number.

You can select from one hundred user programs (U00–

U99) and one hundred preset programs (P00–P99). You

can select programs even if you’re in Rhythm & Bass

mode, Phrase Trainer mode (except while recording), or

Utility mode (except while in certain screens).

PROGRAM MEMORY [A], [B], [C], [D] buttons

You can assign four of your favorite programs to the PROGRAM

MEMORY [A]–[D] buttons. While you perform, simply press

the corresponding PROGRAM MEMORY [A]–[D] button and

the selected program will be recalled instantly.

Here’s how to assign a program to a button. In this example,

we’ll assign the selected program to button [A].

1 Use the π/† CURSOR to select the program you

want to assign to button [A].

2

Press and hold the PROGRAM MEMORY [A] button

for approximately one second. The LCD will indicate

“PGM>A,” and the selected program will be assigned

to button [A].

You can use a foot switch connected to the FOOT SW

jack to switch between the four programs assigned to

PROGRAM MEMORY [A]–[D] (☞p.34 “FOOTSW”).

Using foot switches to select programs

If you connect foot switches to the PX5D’s FOOT SW jack

and use Utility mode to assign the Pedal Switch function,

you’ll be able to use the foot switches to select programs.

Use the included cable for FOOT SW jack to connect your

foot switches. The red jack on one end of the cable will be

Program Up, and the other white jack will be Program

Down (☞p.11 “Making connections,” p.34 “ FOOTSW”).

Master level

When you turn the Value encoder to adjust the master

level, the master level value will be shown in the program

number/value display for several seconds. The bar graph

will also change to indicate the level. The master level is

remembered even when the power is turned off.

Master level value

Program number display

Bar gragh

17

You can also adjust the settings so that the π/† CUR-

SOR will adjust the master level (☞p.18 “Specifying the

function of the Value encoder”).

Bypass/Mute

When you press the TAP/BYPASS button for approxi-

mately one second, the PX5D will be bypassed, and the

original sound will be dry (no effects). The effect chain

will blink, and the display will indicate “BYPASS” for

approximately one second.

If you press and hold the TAP/BYPASS button for ap-

proximately two seconds, the output signal will be mut-

ed. The effect chain will blink rapidly, and the display

will indicate “MUTE” for approximately one second.

Bypass/mute will be turned off when you press the TAP/

BYPASS button once again. You can also return to Play

mode by pressing the EXIT button. Bypass or Mute can

also be entered from modes other than Play mode.

You can also activate Bypass or Mute using two foot

switches connected to the PX5D (☞p.34 “ FOOTSW”).

Tuner

The tuner will operate when you bypass or mute.

meter

center mark

sharp

note name

calibration

1 Play a single string on your guitar or bass.

The LCD will show the note name and the calibra-

tion. If the pitch is more than a semitone higher than

the note name, a sharp symbol will appear at the

upper right of the note name.

2 The display area will act as a meter to show the pitch.

Tune each string of your guitar or bass so that the

indicator above the center mark is lit.

3 When you press either the TAP/BYPASS button, the

tuner (bypass/mute) will be turned off. You can also

return to Play mode by pressing the EXIT button.

Calibration (Standard pitch A = 440)

You can use the Value encoder to adjust the calibration

in the range of A = 438 Hz–445 Hz. The calibration set-

ting you make will remain until the power is turned off.

Once the power is turned off, calibration will be reset to

A = 440 Hz.

18

Specifying the function of the Value encoder

You can specify the function that the Value encoder will

perform in Play mode. While in Play mode, hold down the

EXIT button and press either the √ CURSOR or the ®

CURSOR to assign the following functions.

●

Hold down the EXIT button and press the √ CUR-

SOR. The LCD will indicate “MASTER” for approxi-

mately one second. The Value encoder will adjust the

master level, and the

π

/

†

CURSOR will select pro-

grams. You can use the Value encoder to quickly ad-

just the master level. Each time the power is turned

on, this setting will be in recalled.

Adjust the

master level

Select

a program

● Hold down the EXIT button and press the ® CUR-

SOR. The LCD will indicate “PROGRAM” for ap-

proximately one second. The Value encoder will se-

lect programs, and the

π

/

†

CURSOR

will adjust the

master level. You can use the Value encoder to quickly

select programs.

Select a

program

Adjust the

master level

Key Lock function

By activating the Key Lock function, you can disable all

operations except for selecting programs. This is a con-

venient way to prevent accidental operation during a live

performance.

● Hold down the EXIT button and press the TAP/BY-

PASS button. The LCD will indicate “KEYLOCK”

for approximately one second. The value encoder,

buttons, and knobs other than the

π

/

†

CURSOR,

PROGRAM MEMORY [A]–[D] buttons, and the foot

switches will not function.

Only program

selection is

possible

The Key Lock function will be cancelled when the

power is turned off. You can also cancel the Key Lock

function by performing “Specifying the function of

the Value encoder.”

19

Rhythm & Bass mode

The PX5D provides 128 different rhythm & bass patterns.

You can also connect up to 16 patterns for consecutive

playback.

From Play mode (except when Mute, Bypass, or Key Lock

are active), AUX Pitch mode, or Phrase Trainer mode, press

the RHYTHM button to enter Rhythm & Bass mode. The

pattern will start according to the play type you’ve se-

lected. The bar graph will change according to the rhythm

pattern that’s playing.

Press the EXIT button to return to

Play mode.

Rhythm & Bass mode provides three types of play.

PTN: Pattern play

You can select one rhythm pattern and play it. The LCD

shows the PTN icon.

CHAIN: Chain play

You can connect up to 16 patterns for consecutive play-

back. Playback will start after a pre-count.

SONG: Song play

This lets you play the demo songs. Playback will start

after a pre-count.

Each time you press the RHYTHM button, you’ll cycle

through the choices of PTN→CHAIN→SONG→PT-

N→CHAIN→SONG ..., and the LCD will show the icon

for the currently selected type of play.

When you enter Rhythm & Bass mode, the selected type

of play will be the type that had been selected when you

last exited Rhythm & Bass mode.

If you set the Phrase Trainer recording mode to “JAM,”

you’ll be able to record your guitar or bass phrase along

with the rhythm & bass pattern that’s selected in Rhythm

& Bass mode.

PTN (Pattern play)

This play type lets you select and play one rhythm &

bass pattern. Use the √/® CURSOR to select each pa-

rameter, and use the value encoder and the ENTER/REC

button to specify its value.

The π/† CURSOR

will

switch programs.

Bass key

Level

Reverb level

Te mp o

Rhythm pattern/variation

The settings you select here are remembered even when

the power is turned off.

20

Rhythm Pattern/Variation

Use the Value encoder to select the rhythm pattern (☞p.52

“Rhythm pattern list”). Use the ENTER/REC button to

select the rhythm pattern variation.

BASIC: Basic rhythm pattern.

VARI1: Variation 1. The variation 1 icon will light.

VARI2: Variation 2. The variation 2 icon will light.

Rhythm pattern

variation

icon

Tempo

Use the Value encoder to set the tempo in the range of

40–240 bpm. You can also set the tempo by pressing the

TAP/BYPASS button twice at the desired rhythm.

Tempo

Bass Key

Use the ENTER/REC button to select a bass pattern vari-

ation. Depending on the rhythm pattern that you have

selected, some bass lines will include a chord progression.

OFF: Bass pattern off.

BASIC: Basic bass pattern.

VARI1: Variation 1. This is a major chord bass pattern.

The LCD shows the variation 1 icon.

VARI2: Variation 2. This is a minor chord bass pattern.

The LCD shows the variation 2 icon.

Use the Value encoder to set the key in a range of C,

C#...A#, B allowing you to practice your guitar or bass

in a scale that matches that key.

Root note

If the bass pattern is variation 2 (VARI2), an “m” is shown

beside the root note.

If “MTRONM0”–“MTRONM9”(metronome) is select-

ed as the rhythm pattern, there will be no bass notes, and

this screen will not appear.

ページを読み込んでいます...

Korg PANDORA PX5D 取扱説明書

関連論文

その他の書類