Kyosho 11807, MESSERSCHMITT Bf109E 40(No.11807) ユーザーマニュアル

  • KYOSHO Messerschmitt Bf109E 40 組立説明書についてご質問にお答えします。この説明書には、組み立てに必要な部品、手順、安全上の注意などが詳細に記載されています。モデルの機能や組み立てに関するご質問があれば、お気軽にお尋ねください。
  • このモデルを動かすには他にどんなものが必要ですか?
    組み立て前に確認すべきことは何ですか?
    安全に模型を動かすために注意すべきことは?
    引き込み脚を使用する場合はどうすればよいですか?
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No.11807
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
OPTIONAL PARTS
OPERATING YOUR MODEL SAFELY
WINGSPAN: 1420mm
SAFETY PRECAUTIONS
This radio control model is not a toy!
For Intermediate
&
Advanced flyers.
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
3
3~14
15
15~16
RADIO CONTROLLED ENGINE POWERED SCALE AIRCRAFT
KYOSHO SUPER QUALITY WARBIRDS SERIES
Before commencing assembly, please read these instructions thoroughly.
Messerschmitt Bf109E 40
© 1999 KYOSHO
40
INDEX
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of children s reach!
Take care before operating this model.
You are responsible for this model s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
Sharp Hobby Knife
Phillips Screwdriver (L, M, S)
Needle Nose Pliers
Awl
Scissors
Wire Cutters
2
REQUIRED FOR OPERATION (Purchase separately!)
TOOLS REQUIRED (Purchase separately!)
1
A minimum 4 channel radio control
system for aircraft
3 12
12 AA-size batteries,
either dry cell or NiCd.
Read instruction manual supplied with radio control system thoroughly before use.
5
For retract gear, you will need 5channel radio, 1 retract servo,
1 extension cord.
AAAA
AAAA
AAAA
2
Model Aircraft Engine
Muffler
Muffler Adapter
Engine and Muffler
Glow Plug
3
2
Extension Lead x 2
(200mm)
1
Y- Harness x 1
Purchase a propeller that
will suit your engine.
Propeller
CAUTION
: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION
: Only use radio control systems designed for 
aircraft.
2 40 ~ 46
4 48 ~ 53
2 Stroke .40 ~ .46
4 Stroke .48 ~ .53
Propeller
4
Fuel Tube
Double Side Tape
Shook Protecting Foam
x5
This model will require a minimum 4 channel radio control
(with 5 standard servos) for aircraft, if having fixed
undercarriage, or 5 channel radio (with 6 standard servos),
if fitting retractable undercarriage.
One-touch Plug Heater Set
Required for engine starting:
Fuel Bottle
Plug Wrench
5
Model Glow Fuel.
MO
DEL
EN
G
INE
FUEL
6
SILICONE
Epoxy A
Epoxy B
Instant Glue
(30 )
Epoxy Glue (30 minute type)
Silicone Glue
Glue
WARNING: Never use petrol/
gasoline with glow
engines.
Engine Starter
12V
12V Battery (for starter)
Other equipment for enhancing aircraft operation & performance
For retracting landing gear.
Fuel Filter
Retracting landing gear
Rod and screw
7
8
3
1
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
3
Symbols used throughout this instruction manual comprise the following:
Main Wing
1
Apply epoxy glue.
Assemble left and right
sides the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Do not overlook this
symbol!
Pay close attention here!
Warning!
Secure aileron hinges with instant glue,
being careful not to glue the wing and
aileron together.
Align the center line of
main wing with aileron.
Main Wing
2
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Cut away covering film only.
2 x 6mm
2 x 6mm
2 x 6mm
3mm
2 x 22mm
2 x 22mm
Screw
4
2 x 6mm
Screw
Adjust the travel of each control surface.
Please refer to .
24
24
2mm
Warning!
2
3mm
Set Screw
4
90
4
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Main Wing
4
Main Wing
3
Aileron Servo
Included with the radio set.
2 x 6mm TP
TP Screw
8
Fix the screws securely.
Failvre in flight will cause your model to crash.
1.5mm
Do not disregard this symbol!
Warning!
Note, P13 26 P.14 31 , if you are using retracting landing gear.
3 x 10mm
Ensure that the two wing halves are securely
glued together.
Warning!
P.13 26 P.14 31
Note, P13 26 P.14 31 , if you are using retracting landing gear.
P.13 26 P.14 31
Note, P13 26 P.14 31 , if you are using retracting landing gear.
P.13 26 P.14 31
4
Stopper (L)
3mm
Set Screw
8
4
3 x 10mm TP
TP Screw
2.5mm
Main Wing
Main Wing
6
7
Cut away covering film only.
Cut away covering film only.
5
Apply epoxy glue.
Assemble left and right sides
the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Main Wing
5
Do not disregard this symbol!
Warning!
Assemble left and right sides
the same way.
A
A = AÕ
Main Wing
Cut away only covering film.
4.1mm
Align with main wing holes.
9
8
Engine Mount
Align lower face of engine
mount arm on "Crankshaft
Center line".
4 x 20mm
Cap Screw
4
4
4x20mm
4mm
4x20mm
A
A
2
A
2
Crankshaft Center Line
4mm
4mm
Blind Nut
4 x 30mm
Cap Screw
2
2
4mm
Washer
2
4mm
Blind Nut
6
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
7
11
Fuel tank
3x18mm
5mm
After confirming the position
(see front view of fuel tank),
insert and tighten the screw.
Fix with silicone glue.
Tank Support bar.
6 6mm
3 x 18mm
Screw
1
10
Engine Mount
Throttle Rod
117mm
4
3 x 25mm
Screw
4
3mm
Washer
4
3mm
Nut
3.1mm
4mm
Apply epoxy glue.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Engine Mount
Washer
3mm
3 x 25 mm
Nut
3mm
Engine
Depends on the position
of the throttle arm.
A A’
B’B
C
C’
Cut away only covering film.
mm
A = A’ B = B’
C = C’
Warning!
Ensure that the horizontal stabiliser is
securely glued to the fuselage.
Ensure that the horizontal
stabiliser issecurely glued
to the fuselage.
1.5mm
12
Cowling
2 x 10mm TP
TP Screw
2 x 10mm
3 x 16mm
4
3 x 16mm TP
TP Screw
2
Horizontal / Vertical Tail
13
Secure elevator hinges with instant glue,
being careful not to glue the elevator
to the horizontal stabiliser.
Relieve the cowl to
clear the engine head.
mm
8
Apply epoxy glue.
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
Do not disregard this symbol!
Warning!
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
X
2
2
Assemble as many times as
specified (here:twice).
Assemble left and right sides
the same way.
L
X
2
L
1
Stopper (S)
Stopper (S)
3mm
Set Screw
3mm
2
1
2 x 10mm TP
TP Screw
2 x 10mm
Warning!
1.5mm
To servo .
To elevator horn.
2mm
2mm
2mm
Heat-shrink Tube
Beware of the flame!
Slide heat shrink tubes over linkage rods and use
a hair dryer or similar to secure (shrink) them in place.
Be careful not to burn the
heat-shrink tube!
Bend at end of rod.
Bend at end of rod.
To elevator horn.
15
Elevator Rod
X
2
Secure rudder hinges with instant glue,
being careful not to glue the rudder
to the vertical fin.
To servo.
To rudder horn.
2mm
2mm
Heat-shrink Tube
Beware of the flame!
Slide heat shrink tubes over linkage rods and use
a hair dryer or similar to secure (shrink) them in place.
Be careful not to scorch the
heat-shrink tube!
Bend at end of rod.
14
Rudder Rod
9
Apply epoxy glue.
Must be purchased separately!
2
Assemble as many times as
specified (here:twice).
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
Vertical Fin
Pay close attention here!
16
Apply instant glue
(CA glue, super glue).
Do not disregard this symbol!
Warning!
Elevator rod
Elevator horn
Rudder horn
Rudder rod
Cut away only film.
2 x 14mm
Screw
4
2 x 14mm
Screw
2 x 14mm
2 x 14mm
2
2 x 6mm
Screw
2 x 6mm
45mm
3
3mm
Set Screw
6
3mm
2 x 6mm
2 x 6mm TP
TP Screw
6
30mm
Assemble left and right
sides the same way.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
2mm
1.5mm
Cut away only film.
Cut away film and balsa.
10
Cut off shaded portion.
Horizontal Stabiliser
17
Vertical Fin / Rudder
18
Horizontal / Vertical Tail
19
Horizontal Tail /Stabiliser
20
Paint the canopy frame in black.
1.5mm
2 x 6mm TP
TP Screw
2 x 6mm
6
11
Must be purchased separately!
2mm
pecified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Radio Equipment
21
Pay close attention here!
3mm
Set Screw
1
2mm
Washer
1
(B)
Linkage Stopper (B)
1
2mm E
E ring
1
Canopy
22
Ensure smooth non-binding
movement while assembling.
3mm
2mm
E
E ring
Throttle Servo
Elevator Servo
Rudder Servo
Battery / Receiver
CG
2mm
87mm
Rudder Control.
Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according
to your requirements and flight experience.
15 mm
15 mm
30 mm
10 mm
10 mm
RUDDER
ELEVATOR
AILERON
30 mm
Elevator Control.
Apply included decals to nose cowl side.
For the correct location of decals, plese refer to the box top.
Aileron Control.
12
Assemble left and right sides
the same way.
Apply instnt glue(CA glue,
super glue).
24
Decals
25
Pay close attention here!
Main gear
23
Clear.
Gray.
Retractable Gear
Included with the radio set.
Retract Servo
Included with the radio set.
Retractable Gear
Retractable Gear
Retractable Gear
13
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased separately!
Cut off shaded portion.
26
27
28
68mm
160mm
A retractable landing gear system is not included in this kit and must be purchased separately.
To install retractable undercarriage, a minimum 5 channel radio with 1 additional retractable
gear servo and 1 extension cord is required.
View from Underside of Main Wing
Cut out the outline of wheel well to
a diameter of 68mm. Cut out the wheel
well inserts shown in Section first,
and use them as a guide when cutting
wheel well recesses to ensure that you
do not cut holes oversize.
29
View from Top Side of Main Wing
RETRACTABLE GEAR (PURCHASE SEPARATELY)
Cut off excess.
Bend wire for smooth operation.
Make sure linkages for landing gear are properly locked.
If linkage rods foul, bend accordingly to ensure
free movement.
14
Assemble left and right sides
the same way.
Cut off shaded portion.
Pay close attention here!
29
30
31
Apply instant glue
(CA glue, super glue).
Retractable Gear
Retractable Gear
Retractable Gear
Remove shaded area.
View from Underside of Main Wing
Nylon Propeller
PP
P.P. Pipe
300
Fuel Tube Stopper
Polipropylene Pipe
200
90469
91490
90410-06
D10 x P6 Nylon Propeller
Nylon Propeller
Nylon Propeller
Nylon Propeller
Nylon Propeller
Nylon Propeller
D11 x P7
550
650
D10 x P8
D10 x P7
550
550
D11 x P8 650
90411-07
90410-08
90410-07
90411-08
D12 x P6 750
750
90412-06
D12 x P8
90412-08
OS52 (UNF 1/4 - 28)
Adopter nut. For OS.52
350
YS53 (M6)
Adopter nut. For YS.53
350
90487-05
90487-06
15
PARTS
No. Part Names Quantity
11807-01
90424-70
Cowling
Scale Spinner(70mm)
1 2500 200
200
11807-03
Main gear (with cover)
1
( L.R ) 1500
700
200
No. Part Names
:FOR JAPANESE MARKET ONLY.
Quantity
:FOR JAPANESE MARKET ONLY.
11807-02
Canopy
1 11500 200
OPTIONAL PARTS
No. Part Names
200
200
200
200
No. Part Names
200
200
200
200
200
200
200
2 ~46 4 ~53
 This model aircraft is designed for Intermediate to Experienced fliers. Beginners should seek advice for pre-flight adjustments
and assembly from more experienced fliers. Be aware that flying a badly assembled or badly adjusted aircraft is very
dangerous!
 At the start, first-time fliers should always be assisted by an experienced flier and NEVER fly alone!
 This model aircraft is designed to be powered by either a 2 stroke .40 ~ .46 size engine or a 4 stroke .48 ~ .53 size engine. 
 Installing a more powerful engine than specified or flying this model dangerously could lead to serious injury and/or damage
to property.
Do not overlook this symbol!
Warning!
Warning!
OFF
ON
Pre-Flight Checks
Only fly model aeroplanes in areas
away from houses and places
where people gather. The weight
and speed of your aeroplane make
it a potential hazard. Make sure
that the area around you is clear.
For radio equipment, refer to the
instruction manual included with
your set.
Check that the spinner and the
propeller are securely fastened.
If the model begins to operate by
itself, there is another transmitter
operating on your frequency. Do
not try to operate your model if
this happens, but change your
transmitter and receiver crystals
to another frequency.
Fully extend
transmitter
aerial.
Switch on the transmitter.
Switch on the receiver.
Check that the wings are properly
and firmly affixed.
Flying
Fill the fuel tank.
By moving the various transmitter
controls, ensure that all control
surfaces move the way you
intend them to.
To start the engine, set low throttle
on the transmitter and hold the
engine starter against the spinner.
Switch on engine starter.
Adjust the throttle needle.
After Flying
Only use genuine KYOSHO parts.
Safety Precautions
Always adjust the engine from
behind, and never from in front or
from the side. A rotating propeller
could badly injure you.
Do not allow spectators to get too
close to the model, especially a
rotating propeller.
Immediately replace defective
propellers and spinners.
Always ensure that your
transmitter and receiver batteries
are fully charged.
For best results,
use rechargeble
Nicd cells.
Do not fly your aeroplane too close
to spectators.
ON
ON
Launch the aeroplane into the wind.
Do not fly your aeroplane if it is a
windy day or there are strong
cross winds.
Always land the aeroplane into the
wind.
Bring the aeroplane to a halt by
lowering the engine control trim.
After each flight, the engine will be
very hot. Be careful to avoid
accidentally burning yourself.
Wipe up any fuel deposits or dirt.
Never dispose of fuel or fuel cans
in fires, as this could cause serious
injury.
WIND
WIND
OFF
OFF ON
Switch off the receiver.
Switch off the transmitter.
OFF
Draw remaining fuel from the tank
and dispose of it responsibly.
Move the throttle control stick
on the transmitter and check
that the carburettor opens and
closes easily.
R
THE FINEST RADIO CONTROL MODELS
PRINTED IN CHINA85290005-1
Non-observance of this information could lead to serious injury and/or damage to property.
Warning!
FLIGHT MANUAL
243-0034 153
TEL.046-229-4115
( ) 10:00~18:00
/