Tektronix TEK-USB-488 ユーザーマニュアル

TEK-USB-488

GPIB to USB Adapter

User Manual

www.tektronix.com

071-1839-01

national copyright laws and international treaty provisions.

Tektronix products are cove red by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously

published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK a re registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 5 00

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Warranty 2

Tektronix warrants that this product will be free from defects in materials and workmanship for a period o f one (1) year from the date of shipm ent. If

any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge f or parts

and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for

warranty work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the de fect before the expiration of the warranty period and make

suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defect ive product to the service

center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a

location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties,

taxes, and any other charges for products returned to any other locations.

This warra nty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix

shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than Tektronix

representatives to install, repair or service the product; b) to repair damage resulting from improper use or connectio n to incompatible equipment; c) to

repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modiﬁed or int egrated with

other products when the effect of such modiﬁcation or integration increases the tim e or difﬁculty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR

IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY

PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY

INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS

ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

Table of Contents

General Safe ty Summary . .. ............................................................................................................... iii

Environmental Considerations ............................................................................................................. vi

Preface..................................................................................................................................... vii

Key Features......................................................................................................................... vii

Installation .................................................................................................................................. 1

Standard Accessories ................................................................................................................ 1

Optional Accessories ................................................................................................................. 1

Controls an d Connectors .. ........................................................................................................... 3

Connecting Power .................................................................................................................... 4

Connecting Cables.................................................................................................................... 8

Setting the GPIB Address ............................................................................................................ 9

Updating Firmware................................................................................................................... 11

Mounting the Adap ter . ............................................................................................................... 14

Troubleshooting............................................................................................................................ 16

Speciﬁcations.............................................................................................................................. 21

Certiﬁcations and Compliances ..................................................................................................... 24

TEK-USB-488 GPIB to USB Adapter User Manu al i

Table of Co ntents

ii TEK-USB-488 GPIB to USB Adapter User Manual

General Safety Summary

Review the following safety precaut ions to avoid injury and prevent damage to this product or any products con nected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedu res.

To Avoid Fire or Personal Injury

Use Proper Power Cord. Use only the power cord speci ﬁe d for this product and certiﬁed for the country of use .

Observe All Terminal Ratings. To avoid ﬁre or shock hazard, observe all ratings and markings on the product. Consult the

product manual for furt her ratings information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, th at exceeds the maximum rating of that terminal.

Do Not Operate Without Covers. Do not operate this product with covers or panels removed.

Do Not Operate With Suspected Failures. If you suspect that there is damage to this product, have it inspected by qualiﬁed

service personnel.

Avoid Exposed Circuitry. Do not touch exposed connections and components when power is present.

Use Proper AC Adapter. Use only the AC adapter speciﬁed for this product.

TEK-USB-488 GPIB to USB Adapter User Manu al iii

General Safety Summary

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation.

Refer to the manual’s installation instructions for details on installing the produ ct so it has proper

ventilation.

TermsinthisManual

These terms may appear in this manual:

WARNING. Warning statements ide ntify conditions or practices th at could result in injury or loss of life.

CAUTION. Caution sta tements identify conditions or practices that could result in dama ge to this product or other property.

Symbols and Terms on the Product

These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the marking.

iv TEK-USB-488 GPIB to USB Adapter User Manual

General Safety Summary

WARNING indicates an injury hazard not immediately accessible as you read the marking.

CAUTION indicates a hazard to property including the product.

The following symbols m ay appear on the product:

TEK-USB-488 GPIB to USB Adapter User Manu al v

Environmental Considerations

Product End-of-Life Handling

Observe the following guide lines when recycling an instrument or component:

Equipment Recycling. Production of this e quipment required the extraction and use of natural resources. The equipment may

contain substances that could be harmful to the environment o r human health if improperly handled at the product’s end of life. In

order to avoid release of such substan ces into the environment and to reduce the use of natural resources, we encourage you to

recycle this product in an appropriate system that will ensure that most of the materials are reused or recycled appropriately.

The symbol shown below indicates that this product co mplies with the European Union’s requirements according to Directive

2002/96/EC on waste electrical and electronic equipment (W EEE). For information about recycling options, check the

Support/Service section of the Tektronix Web site (www.tektronix.com).

Restriction of Hazardous Substances

This product h as been classiﬁ ed as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS Directive.

This product is known to contain lead, cadmium, and hexavalent chromium.

vi TEK-USB-488 GPIB to USB Adapter User Manual

Preface

This manual describes the installation and

operation of the TEK-USB-488 GPIB to USB

Adapter. The adapter allows you to connect a

USB device port o n your USBTMC-USB488

compliant instrument, such as a DPO4000

Series oscilloscope, to a GPIB (IEEE488)

controller.

Controller GPIB Adapter USB Instrument

Key Features

Key features include:

GPIB control of USBTMC-USB488 comp liant Tektronix instrum e nts through th e USB port. The USBTMC protocol enables U SB

devices to communicate using IEEE488 style messages. This l ets you run your GPIB software applications on USB hardware.

Fast data transfer rates

Power from either the USB host or an optional external power supply

TEK-USB-488 GPIB to USB Adapter User Manu al vii

Preface

viii TEK-USB-488 GPIB to USB Adapter User Manual

Installation

Unpack the ada pter and check that you received all the items listed as standard accessories. Check the Tektronix Web site

(www.tektronix.com) for the most current information.

Standard Accessories

Description Part number

User Manual 071-1839-00

USB cable (2 each, 1 m e ter)

174-4401-00

Optional Accessories

Description Part number

GPIBcable(1meter)

012-0991-01

GPIBcable(2meter)

012-0991-00

External power supp ly (order po wer cord

separately)

119-5883-0 0

United States power cord

161-0066-00

Universal European power cord 161-0066-09

United Kingdom power cord 161-0066-10

TEK-USB-488 GPIB to USB Adapter User Manu al 1

Installation

Description Part number

Australia power cord 161-0066-13

Switzerland power co rd

161-0154-00

Japan power cord 161-A005-00

China power cord

161-0304-00

India/South Africa power cord

161-0400-00

2 TEK-USB-488 GPIB to USB Adapter User Ma nual

Installation

Controls and Connectors

1. GPIB Connector

2. Adapter Status indicato r ( See Table 1 on

page 19.)

3. USB Statu s indicator (See Table 2 on

page 20.)

4. USB Host port for connection to the USB

Device port on the controlled instrument

5. USB Device port. A USB host can provide

power to the ad apter via this port. This

port is for power only. No USB device

functionality is provide d.

6. Power Connector. For use with the optional

external power supply, Tektronix part

number 119-5883-00.

7. Power indicator. Lighted when power is

applied.

TEK-USB-488 GPIB to USB Adapter User Manu al 3

Installation

Connecting Power

You can con nect power to the adapte r in one of two w ays:

From a USB host port

From the optional external power supply

Connecting USB Power

To apply power to your ad apter from a USB host port, do the following procedure:

1. Connect the device end of a USB cable to

the USB Device port on the rear panel of

the adapter.

2. Connect the host end of the USB cable to

a USB Host port on the equipment that is

to provide power (typically the instrument

being controlled or a PC).

4 TEK-USB-488 GPIB to USB Adapter User Ma nual

Installation

3. Verify that the Power LED lights and that

the USB and Adapter Status LEDs turn

on and t hen off. This indicates that the

adapter is initializing correctly.

TEK-USB-488 GPIB to USB Adapter User Manu al 5

Installation

Connecting the External Power Supply

To apply power to your adapter from the optional AC power unit, do the following procedure:

1. Connect the output power cable from the

power un it to the 5 VDC connector on th e

rear panel of the ad apter.

2. Connect one end of the optional power

cord to the exte rnal power supply.

3. Connect the other end of the power cord to

the wall power outlet.

6 TEK-USB-488 GPIB to USB Adapter User Ma nual

Installation

4. Verify that the Power LED lights and that

the USB and Adapter Status LEDs turn

on and t hen off. This indicates that the

adapter is initializing correctly.

TEK-USB-488 GPIB to USB Adapter User Manu al 7

Installation

Connecting Cables

NOTE. The following cables can be connected while the instruments are powered on.

To connect the TEK-USB-488 GPIB to USB Adapter to USB and GPIB cables, do the following procedure:

1. Connect a GPIB cable from the GPIB

controller to the GPIB port on the adapter.

2. Connect a USB cable fro m the Device port

on the instrument to the Host p ort on the

adapter.

8 TEK-USB-488 GPIB to USB Adapter User Ma nual

ページが読み込まれています...

Tektronix TEK-USB-488 ユーザーマニュアル

Tektronix TEK-USB-488 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント