Motorola FINITI クイックスタートガイド

1

HZ800

2

1

Contents

Congratulations

Your headset

Charge it

Basics

Pair & connect

Be clear

Calls

Talk time

Status light

Settings

Problems?

Safety, Regulatory & Legal

2

3

4

5

10

13

14

15

16

17

18

21

2

Your Motorola Finiti™ headset delivers the best sound in any condition and

Without raising your voice. CrystalTalk™ dual microphones are used for everyday

noise cancellation, and the stealth mode for windy or extreme conditions.

Some other cool features:

• Hear and reply to phone text messages with MotoSpeak™.

• Hear the caller’s name and use your voice to answer or ignore calls.

• Stream Bluetooth® music from your phone.

• Voice prompts to guide you on connections, battery level, and other functions.

• Simultaneous connect with two phones.

We’ve crammed all of the main features of your headset into this handy guide,

and in a matter of minutes we’ll show you just how easy your headset is to use.

So go on, check it out.

more information

on the Web: www.motorola.com/support

Caution: Before using your headset for the rst time, please read the important

Safety, Regulatory & Legal information at the back of this guide (page 21).

Congratulations

3

the important parts

Warning:Do not apply pressure or squeeze the stealth mode sensor (small

rubber balloon), as it can damage the parts inside and will void the warranty.

Your headset

Call

Button

MicroUSB

Charging

Connector

Volume

Buttons

the

Stealth

Mode

Button

Status

Light

Ear

Loop

Power

Switch

Earhook

Earpiece with

the Stealth

Mode Sensor

side view

4

let’s get you up and running

While your headset is charging, you won’t be able to use it.

Note: Your battery is designed to last the life of your product. It should only be

removed by a recycling facility. Any attempt to remove or replace your battery will

damage your headset.

Charge it

Status Light

Red/Yellow - charging

Green - fully charged

5

Basics

a few essentials to get you started

Change ear tting

Your headset comes with multiple ear ttings.

Choose your ear tting (loop or spring) so

your headset is comfortable.

Lift the current ear tting up and slide it off the headset

in an upward direction.

Left

Ear

Spring

Right

Ear

Spring

Large

Ear

Loop

Medium

Ear

Loop

Small

Ear

Loop

6

Basics

Slide the new ear loop or spring downward onto

the earpiece, then align and push the bottom onto the

groove.

Wear it

Bend the ear loop or spring and insert the

earpiece into your ear. Make sure the

stealth mode sensor is in contact

with your ear canal.

Place the ear loop or spring in the bend of

your ear.

Groove

the Stealth

mode sensor

Ear canal

7

Basics

Flex the earhook and loop it over your ear, and point the headset

microphone towards your mouth.

Turn it on & off

Listen to music

Note: This feature is phone dependent.

Your headset allows you to stream Bluetooth music from your phone. Music

playback is started and controlled from your phone.

8

While a call is active, music pauses. When the call ends, music resumes playing.

Enhanced call features

Tell headset to answer or ignore calls

Use your voice to answer or ignore an incoming call:

• say “answer” to answer the call

• say “ignore” to ignore the call

Note: This feature does not work for second incoming calls.

Hear caller’s name

If your phone knows your caller’s name, then you hear “call from <name>” on an

incoming call.

Basics

9

Basics

Clean your headset

Keep your headset clean and dry. High humidity or perspiration can make the ear

tting feel slippery. Remove the ear tting and wipe it with a soft cloth to remove

dirt and moisture.

Note: Be very careful when wiping near the stealth mode sensor.

Also check for any debris that may be blocking the small speaker port on the ear

tting.

10

connect and go

Pair & connect with your phone

Turn off any Bluetooth® devices previously paired with your headset.

Turn on the Bluetooth feature on your phone.

Put the headset on your ear (see “Wear it” on page 6).

Turn on your headset (see “Turn it on & off” on page 7).

The status light becomes steadily lit in blue and you hear “ready to pair”.

Follow the voice prompts to connect your phone to your headset.

Note: When prompted for the passkey, enter 0000.

When your headset successfully pairs with your phone, you hear “pairing

complete”.

For daily use, make sure your headset is turned on, and your phone’s Bluetooth

feature is on. Your headset and phone connect automatically.

Pair & connect

11

Pair & connect

Pair & connect a second phone

Turn off rst phone and any other Bluetooth devices previously paired

with your headset.

Turn your headset off.

Turn on the Bluetooth feature on your phone.

Put the headset on your ear.

Turn on your headset.

The status light becomes steadily lit in blue and you hear “ready to pair”.

Follow the voice prompts to connect your phone to your headset.

Note: When prompted for the passkey, enter 0000.

When your headset successfully pairs with your phone, you hear “pairing

complete”.

To connect to both phones, turn on the rst phone while the second phone

is connected. When you hear “<phone 1 name> connected”, your headset is

connected to both phones.

12

Test your call connection

Place the headset on your ear.

On your phone, dial a phone number and press the Call/Send key.

If your phone and headset are successfully connected, you hear ringing on the

headset.

Pair & connect

13

Be clear

your voice, not all the noise

Always be heard during calls with the CrystalTalk dual microphones and the

stealth mode sensor:

• CrystalTalk is always on to cancel out everyday background noise.

• The stealth mode can be turned on when noise and wind get really bad to shut

out all background noise.

Turn on the stealth mode

Press the Stealth Mode button and listen for the

“stealth mode on” or “stealth mode off” prompt.

Note: Make sure the stealth mode sensor is placed correctly and is in contact

with the ear canal (see page 6). It is normal for the sound of your voice to be less

“natural” in the stealth mode.

the Stealth

Mode Button

14

Calls

it’s good to talk

Note: Some features are phone/network dependent.

To...

answer call

reject call

make a voice dial call

redial last call

mute or unmute a call

end a call

Say “answer” or press the Call button.

Say “ignore” or press and hold a Volume button until

you hear a tone.

Press the Call button and you hear a tone.

Press and hold the Call button until you hear a tone.

Press both Volume buttons.

Press the Call button.

Answer second incoming call

Reject second incoming call

Press the Call button.

Press and hold a Volume button until you hear a tone.

Tip: When connected to two phones, follow the voice prompts to perform functions

such as voice dial, redial, and end call on the desired phone.

turn on/off stealth mode

Press the stealth mode button.

15

Talk time

check your chat time

Press both Volume buttons while not on a call.

To save battery power, turn off the headset when not using it.

if light shows... and/or you hear…

red “battery level is low"

yellow “battery level is medium"

green “battery level is high”

your remaining talk time is..

less than 1.5 hours

between 1.5 to 3.5 hours

more than 3.5 hours

16

Status light

know your headset

If light shows...

three blue ashes

steady blue

rapid blue/purple ashes

powering on/off

in pairing/connect mode

your headset is...

quick blue ash

quick purple ash

slow blue pulse

slow blue ash

slow green ash

slow red ash

slow purple pulse

steady red

quick red ash

connecting to your phone

receiving or making a call on phone 1

receiving or making a call on phone 2

in standby (not on a call—connected to one phone)

in standby (not on a call—connected to two phones)

on a call

in a low battery state

trying to connect to your phone

muting the call

idle (not connected to a phone)

Note: After 1 minute on a call or 20 minutes of inactivity, the light stops ashing to

conserve power, but the headset remains on.

17

Settings

make some changes

Press and hold the Call button while turning on the headset to turn these features

on/off:

• Reset to factory default

Caution: This action erases all pairing information stored in your headset.

• Caller ID

• Voice prompts

• Multipoint (two phone) connections

Follow the voice prompts to make changes to these settings.

18

Problems?

we’ve got solutions

My headset will not enter pairing mode

Make sure that any devices previously paired with the headset are turned off.

If the status light is not steadily lit in blue, turn off both the other device and

headset, wait 10 seconds, then turn headset back on. Wait for the status light to

become steadily lit in blue, indicating the headset is now in pairing mode.

My phone doesn't nd my headset when searching.

Make sure the status light on your headset is steadily lit in blue when your phone

is searching for devices. If not, press and hold the Call button and both Volume

buttons until you hear “ready to pair” and see the status light steadily lit in blue.

My headset worked before but now it's not working

Make sure your phone is on and the Bluetooth feature is turned on in your phone.

ページが読み込まれています...

Motorola FINITI クイックスタートガイド

このマニュアルも適しています

Motorola FINITI クイックスタートガイド

他の言語で

関連論文