Motorola FINITI クイックスタートガイド

カテゴリー
ヘッドセット
タイプ
クイックスタートガイド

このマニュアルも適しています

1
HZ800
2
1
Contents
Congratulations
Your headset
Charge it
Basics
Pair & connect
Be clear
Calls
Talk time
Status light
Settings
Problems?
Safety, Regulatory & Legal
2
3
4
5
10
13
14
15
16
17
18
21
2
Your Motorola Finiti headset delivers the best sound in any condition and
Without raising your voice. CrystalTalk™ dual microphones are used for everyday
noise cancellation, and the stealth mode for windy or extreme conditions.
Some other cool features:
• Hear and reply to phone text messages with MotoSpeak™.
• Hear the caller’s name and use your voice to answer or ignore calls.
• Stream Bluetooth® music from your phone.
• Voice prompts to guide you on connections, battery level, and other functions.
• Simultaneous connect with two phones.
We’ve crammed all of the main features of your headset into this handy guide,
and in a matter of minutes we’ll show you just how easy your headset is to use.
So go on, check it out.
more information
on the Web: www.motorola.com/support
Caution: Before using your headset for the rst time, please read the important
Safety, Regulatory & Legal information at the back of this guide (page 21).
Congratulations
3
the important parts
Warning:Do not apply pressure or squeeze the stealth mode sensor (small
rubber balloon), as it can damage the parts inside and will void the warranty.
Your headset
Call
Button
MicroUSB
Charging
Connector
Volume
Buttons
the
Stealth
Mode
Button
Status
Light
Ear
Loop
Power
Switch
Earhook
Earpiece with
the Stealth
Mode Sensor
side view
4
let’s get you up and running
While your headset is charging, you won’t be able to use it.
Note: Your battery is designed to last the life of your product. It should only be
removed by a recycling facility. Any attempt to remove or replace your battery will
damage your headset.
Charge it
Status Light
Red/Yellow - charging
Green - fully charged
5
Basics
a few essentials to get you started
Change ear tting
Your headset comes with multiple ear ttings.
Choose your ear tting (loop or spring) so
your headset is comfortable.
Lift the current ear tting up and slide it off the headset
in an upward direction.
Left
Ear
Spring
Right
Ear
Spring
Large
Ear
Loop
Medium
Ear
Loop
Small
Ear
Loop
6
Basics
Slide the new ear loop or spring downward onto
the earpiece, then align and push the bottom onto the
groove.
Wear it
Bend the ear loop or spring and insert the
earpiece into your ear. Make sure the
stealth mode sensor is in contact
with your ear canal.
Place the ear loop or spring in the bend of
your ear.
Groove
the Stealth
mode sensor
Ear canal
7
Basics
Flex the earhook and loop it over your ear, and point the headset
microphone towards your mouth.
Turn it on & off
Listen to music
Note: This feature is phone dependent.
Your headset allows you to stream Bluetooth music from your phone. Music
playback is started and controlled from your phone.
8
While a call is active, music pauses. When the call ends, music resumes playing.
Enhanced call features
Tell headset to answer or ignore calls
Use your voice to answer or ignore an incoming call:
• say “answer” to answer the call
• say “ignore” to ignore the call
Note: This feature does not work for second incoming calls.
Hear caller’s name
If your phone knows your caller’s name, then you hear “call from <name>” on an
incoming call.
Basics
9
Basics
Clean your headset
Keep your headset clean and dry. High humidity or perspiration can make the ear
tting feel slippery. Remove the ear tting and wipe it with a soft cloth to remove
dirt and moisture.
Note: Be very careful when wiping near the stealth mode sensor.
Also check for any debris that may be blocking the small speaker port on the ear
tting.
10
connect and go
Pair & connect with your phone
Turn off any Bluetooth® devices previously paired with your headset.
Turn on the Bluetooth feature on your phone.
Put the headset on your ear (see “Wear it” on page 6).
Turn on your headset (see “Turn it on & off” on page 7).
The status light becomes steadily lit in blue and you hear “ready to pair”.
Follow the voice prompts to connect your phone to your headset.
Note: When prompted for the passkey, enter 0000.
When your headset successfully pairs with your phone, you hear “pairing
complete”.
For daily use, make sure your headset is turned on, and your phone’s Bluetooth
feature is on. Your headset and phone connect automatically.
Pair & connect
11
Pair & connect
Pair & connect a second phone
Turn off rst phone and any other Bluetooth devices previously paired
with your headset.
Turn your headset off.
Turn on the Bluetooth feature on your phone.
Put the headset on your ear.
Turn on your headset.
The status light becomes steadily lit in blue and you hear “ready to pair”.
Follow the voice prompts to connect your phone to your headset.
Note: When prompted for the passkey, enter 0000.
When your headset successfully pairs with your phone, you hear “pairing
complete”.
To connect to both phones, turn on the rst phone while the second phone
is connected. When you hear “<phone 1 name> connected”, your headset is
connected to both phones.
12
Test your call connection
Place the headset on your ear.
On your phone, dial a phone number and press the Call/Send key.
If your phone and headset are successfully connected, you hear ringing on the
headset.
Pair & connect
13
Be clear
your voice, not all the noise
Always be heard during calls with the CrystalTalk dual microphones and the
stealth mode sensor:
• CrystalTalk is always on to cancel out everyday background noise.
The stealth mode can be turned on when noise and wind get really bad to shut
out all background noise.
Turn on the stealth mode
Press the Stealth Mode button and listen for the
stealth mode on” or “stealth mode off” prompt.
Note: Make sure the stealth mode sensor is placed correctly and is in contact
with the ear canal (see page 6). It is normal for the sound of your voice to be less
“natural” in the stealth mode.
the Stealth
Mode Button
14
Calls
it’s good to talk
Note: Some features are phone/network dependent.
To...
answer call
reject call
make a voice dial call
redial last call
mute or unmute a call
end a call
Say “answer” or press the Call button.
Say ignore or press and hold a Volume button until
you hear a tone.
Press the Call button and you hear a tone.
Press and hold the Call button until you hear a tone.
Press both Volume buttons.
Press the Call button.
Answer second incoming call
Reject second incoming call
Press the Call button.
Press and hold a Volume button until you hear a tone.
Tip: When connected to two phones, follow the voice prompts to perform functions
such as voice dial, redial, and end call on the desired phone.
turn on/off stealth mode
Press the stealth mode button.
15
Talk time
check your chat time
Press both Volume buttons while not on a call.
To save battery power, turn off the headset when not using it.
if light shows... and/or you hear
red “battery level is low"
yellow “battery level is medium"
green battery level is high
your remaining talk time is..
less than 1.5 hours
between 1.5 to 3.5 hours
more than 3.5 hours
16
Status light
know your headset
If light shows...
three blue ashes
steady blue
rapid blue/purple ashes
powering on/off
in pairing/connect mode
your headset is...
quick blue ash
quick purple ash
slow blue pulse
slow blue ash
slow green ash
slow red ash
slow purple pulse
steady red
quick red ash
connecting to your phone
receiving or making a call on phone 1
receiving or making a call on phone 2
in standby (not on a call—connected to one phone)
in standby (not on a call—connected to two phones)
on a call
in a low battery state
trying to connect to your phone
muting the call
idle (not connected to a phone)
Note: After 1 minute on a call or 20 minutes of inactivity, the light stops ashing to
conserve power, but the headset remains on.
17
Settings
make some changes
Press and hold the Call button while turning on the headset to turn these features
on/off:
• Reset to factory default
Caution: This action erases all pairing information stored in your headset.
• Caller ID
• Voice prompts
• Multipoint (two phone) connections
Follow the voice prompts to make changes to these settings.
18
Problems?
we’ve got solutions
My headset will not enter pairing mode
Make sure that any devices previously paired with the headset are turned off.
If the status light is not steadily lit in blue, turn off both the other device and
headset, wait 10 seconds, then turn headset back on. Wait for the status light to
become steadily lit in blue, indicating the headset is now in pairing mode.
My phone doesn't nd my headset when searching.
Make sure the status light on your headset is steadily lit in blue when your phone
is searching for devices. If not, press and hold the Call button and both Volume
buttons until you hear “ready to pair” and see the status light steadily lit in blue.
My headset worked before but now it's not working
Make sure your phone is on and the Bluetooth feature is turned on in your phone.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138

Motorola FINITI クイックスタートガイド

カテゴリー
ヘッドセット
タイプ
クイックスタートガイド
このマニュアルも適しています

他の言語で