SCF902
Register your product and get support at
www.philips.com/welcome
Always there to help you
Question?
Contact
Philips
EN User manual 1 ZH-CN 用户手册 16
1
EN
Contents
1 Important 2
Electromagnetic Fields (EMF) 4
2 Introduction 4
3 Overview 5
4 Clean and sterilize 6
5 Assemble 6
6 Use your pump 9
Before using the pump 9
To begin pumping 9
To pause pumping 10
Store your breast milk 11
Feed your baby with your
expressed milk 11
7 Hints to help you
succeed 12
8 When to express milk 12
Right times of the day to
express your milk 12
9 Troubleshooting 13
10 Recycling 15
11 Guarantee and service 15
2
EN
1 Important
Read this user manual carefully before
using your Philips AVENT single
electronic breast pump, and save the
user manual for future reference. You
can also nd this user manual at Philips
website: www.philips.com/support
Warnings
• Always unplug from the
power socket immediately
after use.
• Do not use the breast pump
while bathing.
• Do not place or store the
breast pump where it can
fall or be pulled into a bath
or sink.
• Do not place or drop the
pump motor, silicone tube,
and power adapter into
water or other liquids.
• Do not reach for a product
that has fallen into water.
Unplug from the power
socket immediately.
• Children should be supervised
to ensure that they do not
play with the appliance. Place
the appliance where children
or pets is not reachable.
• Before each use, check the
breast pump, including the
power adapter for signs of
damage. Never operate
the breast pump if it has a
damaged plug, not working
properly, has been dropped
or damaged, or has been
submerged in water.
• The power cord is irreplaceable.
Discard it if is damaged,
including the power adapter.
• Only use accessories
recommended by Philips
AVENT.
• Only use the power adapter
supplied with the product.
• Make sure the breast pump,
including the power adapter,
is not exposed to extreme
heat or placed in direct
sunlight.
• Do not use the breast pump
outdoors.
• There are no user serviceable
parts inside the pump. Do
not attempt to open, service,
or repair the breast pump
yourself.
• The parts of the pump which
come directly into contact
with milk are personal care
items, and should not be
shared between mothers.
• Do not attempt to remove
the pump body from the
breast while under vacuum.
Switch the breast pump off,
and break the seal between
your breast and the pump
funnel with your nger, then
English
3
EN
remove the pump from your
breast. You can also pull off
the silicone tube from the
motor or the cap to release
the vacuum.
• Never use while pregnant as
pumping can induce labor.
• Never use when sleepy or
drowsy.
• This appliance is not
intended for use by persons
including children with
reduced physical, sensory
or mental capabilities,
or lack of experience or
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• If expressing becomes
painful, stop and consult your
breastfeeding advisor or
healthcare professional.
• Do not use the breast pump
in the presence of ammable
anaesthetic mixtures with air,
with oxygen, or with nitrous
oxide.
• Although the breast pump
is compliant with applicable
EMC directives, it may still
be susceptible to excessive
emissions and/or may
interfere with more sensitive
equipment.
Cautions
• The product should not be
left unattended when plugged
into a power socket.
• Never drop or insert any
foreign object into any
opening or the silicone tube.
• Do not shorten the the
silicone tube.
• Before you connect the
breast pump to the power,
make sure that the voltage of
the product corresponds to
the local power voltage.
• Wash, rinse, and sterilize
the appropriate pump parts
before each use.
• Do not use antibacterial,
abrasive cleaners, or
detergents when cleaning
breast pump parts.
• Never put the breast pump
motor in water or sterilizer,
as you can cause permanent
damage to the pump.
• If the vacuum generated is
uncomfortable or cause pain,
switch off the breast pump,
break the seal between the
breast and the pump funnel
with your nger, and then
remove the pump from your
breast. You can also pull off
the silicone tube from the
motor or the cap to release
the vacuum.
4
EN
• Do not continue pumping for
more than ve minutes at a
time if no result is achieved.
• Never use any accessories
or parts from other
manufacturers or that Philips
AVENT does not specically
recommend. If you use such
accessories or parts, your
guarantee becomes invalid.
• Do not use the breast bump
if the silicone diaphragm
appears to be damaged or
broken. Replace the silicone
diaphragm. See chapter
“Guarantee and service” for
information on how to obtain
replacement parts.
• Never use feeding teats
as dummies, paciers, or
soothers. Make sure that
the teething baby does not
bite the teat too long. The
continuous and prolonged
bite will damage the teat. For
hygiene reasons, replace teats
after three months of use.
Use only Philips AVENT teats
and bottles together.
Electromagnetic Fields (EMF)
This Philips appliance complies with all
applicable standards and regulations
regarding exposure to electromagnetic
elds.
2 Introduction
Congratulations on your purchase and
welcome to Philips AVENT! To fully
benet from the support that Philips
AVENT offers, register your product at
www.philips.com/welcome.
This Philips AVENT single electric breast
pump is small and lightweight, and can
be carried around easily. The Let-down
Massage Cushion naturally imitates
your baby’s suckling action to provide
fast milk ow - silently, comfortably, and
gently. The ve suction modes allow
you to choose the suitable suction
strength, so you can express your milk
comfortably and thoroughly. This breast
pump is also designed to separate the
milk ow from air ow, which keeps milk
out of the silicone tube. This ensures
your milk is hygienic, and makes the
pump easy to keep clean.
Doctors recommend that breast milk is
the best nutrition for babies during the
rst year, combined with solid food after
the rst six months, You milk is specially
adapted to your baby’s needs and
contains antibodies which help protect
your baby against infection and allergies.
Your single electric breast pump will
help you breast-feed longer. You can
express and store your milk so that -
whether you are out for a few hours,
taking a well deserved rest, or back at
work - your baby can still enjoy the
benets of your breast milk, even if you
cannot be there to give it yourself. As
the pump is easy to assemble, silent
and discreet, you can take it with you
anywhere, allowing you to express milk
at your own convenience and maintain
your milk supply.
English
5
EN
3 Overview
a Cap
b Silicone diaphragm (x2)
c Pump body
d Let-down Massage Cushion
e Pump cover
f Power adapter
g Valve
h Stand
i Bottle (120 ml)
j Pump motor
k Silicone tube
l Adaptor ring for wide neck bottles
m Sealing disc
n Screw ring
o Teat (0m+)
p Dormal cap
q Pouch
r Sling
abcde
fg hijk
lm
n
o
p
q r
6
EN
4 Clean and
sterilize
Before you use your breast pump for
the rst time and for every time, you
must disassemble, wash, and sterilize all
the breast pump parts that come into
contact with your breast milk. (see b,
c, d, e, g, i in Overview
chapter)
Before you use the bottle and its parts
for the rst time and for every time,
you must also disassemble, wash and
sterilize. (see l, m, n, o, p in
Overview chapter)
Warning
• Never wash or sterilize the pump motor,
the silicone tube, the cap, and the power
adapter. These components do not come
into contact with your breast milk. You
can wipe the pump motor clean with a
soft cloth.
You can also use the dishwasher (top
rack only) or hand wash in warm, soapy
water, and then rinse thoroughly.
We recommend you to sterilize all the
necessary parts in our Philips AVENT
steam sterilizer, or by boiling for 5
minutes.
Caution
• Take care when cleaning the valve and the
silicone diaphragm. If it gets damaged, your
breast pump will not function properly.
• To clean the valve, rub it gently between
your ngers in warm soapy water. Do not
insert objects as this may cause damage.
5 Assemble
To assemble the pump, follow the steps
below.
Note
• Make sure that you clean and sterilize the
pump as instructed in this user manual.
• Make sure that you assemble the pump
correctly as instructed in this user manual.
• To avoid leakage remove the residue around
the rim before assembling. Put the bottle
onto the pump body, and do not over-tighten.
• Wash your hand thoroughly before you take
sterilized components.
1 Insert the valve into the pump body
from underneath.
2 Put the bottle onto the pump body
and turn it anticlockwise to x it. Do
not over-tighten when assembling
the bottle to the pump body.
English
7
EN
Note
• If you use a Philips AVENT wide neck bottle,
put on the adaptor ring.
3 Insert the Let-down Massage
Cushion into the pump funnel and
press the rim to ensure a perfect
seal.
3
4 Put the silicone diaphragm onto the
pump body and press the rim to
make sure a perfect seal.
4
• Note
• It is easier if assembled wet.
5 Firmly push the cap onto the
silicone diaphragm, so that it sites
securely on top of the silicone
diaphragm.
5
8
EN
6 To make the bottle stands stable,
insert it into the stand.
6
Note
• To prevent toppling, insert the bottle into
the stand after each use.
7 Connect the silicone tube to the cap
and the motor rmly.
7
8 Connect the power adapter to the
pump motor, and then insert the
power plug to the power socket.
8
Tip
• For battery operation, open the rear cover
of the motor unit in the direction indicated
by the marks. Insert four new 1.5V AA
alkaline batteries into the battery housing.
Reattach the rear cover to the motor unit.
Note
• A new set of batteries provides up to
2.5 - 3 hours of operation. If you have
inserted batteries in the battery housing of
the motor unit and plug in the adapter, the
breast pump will run from the main power
supply. The batteries cannot be charged in
the unit.
+
-
+
-
+
-
+
-
English
9
EN
6 Use your pump
Before using the pump
• Wash your hands thoroughly, and
make sure your breasts are clean.
Gently squeeze a little milk from
each nipple to make sure that milk
ducts are not blocked.
• Make sure you follow the steps in
“Clean and sterilze” and “Assemble”
chapters to clean, sterilze, and
assemble the breast pump.
• Relax in a comfortable chair, leaning
slightly forward (use cushions to
support your back). Make sure that
you have a glass of water nearby.
To begin pumping
1 Press the funnel and the Let-down
massage cushion of the pump rmly
against your breast. Make sure that
no air escape; otherwise there is no
suction.
1
2 Press the on/off button to switch
on your pump.
» The breast pump automatically starts
up with the lowest level to gently
stimulate, and the left light on the
pump motor will illuminate. You begin
to feel the suction on your breast.
2
3 Once your milk starts owing, you
can press suction increase button
or suction decrease button to
adjust and nd your exact comfort
level.
• Press the suction increase button
to deeper the suction.
• Press the suction decrease button
to lower the suction.
» There are altogether ve modes.
The number of lights will increase or
decrease according to the vacuum
mode selected.
3
10
EN
Note
• You do not need to use the deepest
suction mode, only use the modes that are
comfortable for you.
4 When you have nished expressing,
press the on/off button to switch
off your pump. Carefully remove the
pump body from your breast.
5 Disconnect the the power plug
to the power socket, and then
disconnect the power adapter from
the pump motor.
5
6 Unscrew the bottle from the pump
body ready for feeding or storage.
Clean the other used parts of
the breast pump according to the
instructions in chapter “Clean and
Sterilize”.
Caution
• Do not continue pumping for more than
5 minutes at a time if there is no result. Try
expressing at another time during the day.
• If the process becomes very uncomfortable
or painful, stop using the pump, and consult
your breastfeeding advisor.
• Never tilt the breast pump when the milk
has reached the maximum line on the
bottle. Replace with a new bottle before
re-pumping to avoid spillage.
Note
• If you can express more than 120 ml each
time, use the 240ml Philips AVENT milk
bottle for storage to avoid spillage.
• If the breast pump is on but there is no
operation for 30 minutes, it will automatically
shut down.
Tip
• Place the pump motor on a stable and
at surface, or hang up steadily with the
included sling, to avoid any accidental drops
when in use. If not, this may pull the pump
body off from the breast and cause injury.
To pause pumping
This breast pump has a pause function,
and you can press the pause button
to pause pumping if at any time
the suction becomes uncomfortable,
there is a need to change the bottle,
reposition the pump on the breast, or
change side.
1 When the breast bump is in a
particular suction mode, press pause
button will pause the pumping.
» The respective light will ash to
remind you of the selected suction
mode.
1
English
11
EN
Note
• When the breast pump is in pause, pressing
the suction increase button or suction
decrease button cannot adjust the
suction mode.
2 Press the pause button again
to continue the pumping with the
suction mode selected before
pausing.
Store your breast milk
Caution
• Never refreeze breast milk.
• Do not mix fresh breast milk to already
frozen milk.
• Always discard any left over milk at the end
of a feed.
Note
• Only store the milk collected with a sterile
pump.
1 After you have expressed your milk,
unscrew the pump body from the
Philips AVENT bottle.
2 Store expressed milk in cleaned
and sterilized Philips AVENT bottles
tted with sealing discs. Put them in
the fridge or freezer immediately.
• You can store expressed breast
milk in the refrigerator for up to 48
hours (not in the door) or in the
freezer for up to 3 months.
• Label the bottles with date and time.
• Use up the older milk rst.
Feed your baby with your
expressed milk
• If you use Philips AVENT bottle
to store breast milk, make sure
to remove the sealing disc and
assemble the Philips AVENT teat
for feeding.
• Place the frozen breast milk in the
refrigerator to defrost overnight.
In case of an emergency, you can
defrost the milk in a bowl of hot
water. Use up the defrosted breast
milk within 24 hours after defrosting.
About heating up the breast milk:
• Heat the bottle with in a bowl of
hot water, or using Philips AVENT
bottle and baby food warmer to
safely heat up the milk.
Caution
• Remember! Always check milk or food
temperature before feeding.
• Never heat breast milk in a microwave as
this may destroy valuable nutrients and
antibodies. In addition, the uneven heating
may cause hot spots in the liquid which
could cause burns to the throat.
• Never immerse a frozen bottle in boiling
water to avoid crack or split.
12
EN
7 Hints to help
you succeed
The single electronic breast pump is
easy to use. Take some practice, and
you will soon get used to expressing
milk.
• Choose a time when you are not
rushed nor interrupted easily.
• Having your baby or a photograph
of your baby nearby can help
encourage your milk to ow.
• Before expressing milk, place a
warm towel onto your breast, and
lightly massage for a few minutes.
This encourages milk ow, and ease
the pain of your breast.
• Warmth and relaxation can
encourage milk ow. Try expressing
after a warm bath or shower.
• Try expressing from one breast
while your baby is feeding from the
other, or continue expressing just
after a feed.
• Repositioning the pump on the
breast from time to time can help
stimulate your milk ow.
Tip
• Practice with your pump to nd the best
pumping techniques for you. If the process
becomes painful, stop and consult your
breast-feeding advisor.
8 When to
express milk
If possible, wait until your milk supply
and breast-feeding schedule are well
established, normally at least 2-4 weeks
after birth, unless told otherwise by
your doctor or breast-feeding advisor.
The exceptions are:
• If you are expressing milk for your
baby to be given in hospital.
• If your breasts are engorged (painful
or swollen). You can express a small
amount of milk before or between
feeds to ease the pain, and to help
your baby latch on more easily.
• If you have sore or cracked nipples
and you may wish to express your
milk until they are healed.
• If you are separated from your baby
and wish to continue to breast-feed
when you are reunited. You should
express your milk regularly to
stimulate your milk supply.
Right times of the day to
express your milk
• Early in the morning when you
breasts are full, just before or after
your baby’s rst feed.
• After a feed, if your baby has not
emptied both breasts.
• Between feeds or in a break if you
have returned to work.
English
13
EN
9 Troubleshooting
If you are unable to solve the problem with the provided information, contact the
Philips AVENT Consumer Care staffs. You can also consult your health professional
or breast-feeding advisor.
Problem Solution
Lack of suction Check that all components are assembled correctly and that the
valve is in positioned correctly.
Make sure that the cap, the diaphragm, and the Let-down Massage
Cushion are tted securely to the pump body and a perfect seal is
created.
The air pressure in your region is too low, this may affect the
suction.
Make sure the silicone tube is rmly connected to the cap and the
motor, without twisting.
No milk being
expressed
Make sure the pump is assembled correctly, and the suction is
created.
Relax and try again; as expression may improve with practice.
Refer to the “Hints to help you succeed” section.
Pain in
the breast
area when
expressing
You may be pumping too hard. You do not need to use all
the suction that the pump can generate but the comfortable
modes. Press the suction decrease button to lower down
the suction intensity.
Consult your health professional/ breast feeding advisor.
Milk is drawn
up the Let-
down Massage
Cushion
Remove and ret the Let-down Massage Cushion. Make sure
that it is installed correctly and rmly.
Try leaning lightly forward.
14
EN
Cracking/
Discoloring
Avoid contact antibacterial or abrasive detergents/ cleaners.
Combinations of detergents, cleaning products, sterilization
solution, softened water, and temperature uctuations may
cause the plastic to crack. If any crack is found, stop using the
pump immediately. Contact Philips AVENT Consumer Care
center for spare components.
Food coloring can discolor components, but this will not affect
your usage.
Keep all the components away from the source of heat or
direct sunlight as it can discolor components.
Components
broken or lost
Contact Philips AVENT Consumer Care center for spare
components. See back cover for contact details.
Pump not
responding
Make sure the pump is correctly assembled and press the on/
off button to switch on.
Make sure the cables between the pump and the power
socket are correctly connected.
Pump lights are
showing low
voltage warning
If the ve lights on the motor are sequentially ashing and
the pump motor automatically stop functioning, this means
the breast pump is in low voltage protection mode. If you use
batteries to supply power, press the on/off button to switch
off. Replace with new batteries and switch the pump on again.
When using the power adapter to supply power, make sure it
is connected properly, then switch the pump on again. If this
problem persists, contact the Consumer Care center for help.
Pump light
is ashing
abnormally
If the ve pump lights are ashing non-stop, press the on/
off button to switch off. Check that all components
are assembled correctly. If the assembling is correct, but
the problem persists after switching on again, contact the
Consumer Care center for help.
English
15
EN
10 Recycling
Batteries contain substances
that may pollute the
environment. Do not throw
away batteries with the
normal household waste, but
dispose them at an ofcial collection
point for batteries. Do not throw
away the appliance with the normal
household waste. Please get to know
the local regulation for electrical and
electronic products. By disposing in a
correct way, you help to avoid causing
impact of environment and human
health.
11 Guarantee and
service
Philips Consumer Lifestyle guarantees
its products under correct usage for
a period of two year after the date of
purchase. If any defect due to faulty
materials and workmanship occurs
within this two year guarantee period,
Philips Consumer Lifestyle will repair or
replace the product at its expense. For
repair or replacement, make sure to
provide convincing proof, for instance
by means of a receipt, that the day on
which service is claimed is within the
guarantee period.
The guarantee only covers the breast
pump motor and power adapter. It
does not cover non-electrical parts,
accessories and consumable parts. The
guarantee does not cover shipping and
handling fees, and on-site services fees
either.
If you need service or information, or if
you have a problem, please contact the
Philips AVENT Consumer Care center.
Website:
http://www.philips.com/support
17
ZH-CN
1 重要信息
使用飞利浦新安怡单边电动吸乳器
之前，请仔细阅读本用户手册，并
妥善保管以供日后参考。您也可
以在飞利浦网站上找到本用户手
册：
www.philips.com/support
警告
• 请务必在使用后立
即从电源插座拔下插
头。
• 切勿在沐浴时使用吸
乳器。
• 切勿将吸乳器放置或
存储在可能掉落浴缸
或水槽的地方。
• 切勿将吸乳器马达、
硅胶管、电源适配器
放入或掉入水中或其
它液体中。
• 如果产品掉入水中，
切勿触碰，请先立
即从电源插座拔下插
头。
• 切勿让儿童玩耍该产
品，并将其放在儿童
或宠物接触不到的地
方。
• 每次使用前先检查
吸乳器（包括电源适
配器）是否存在明显
破损。如果吸乳器的
电源适配器已损坏、
不能正常工作、曾被
跌落或损坏，或浸入
水中，请勿使用吸乳
器。
• 电源软线不能更换，
如果软线损坏，此器
具（电源适配器）应
废弃。
• 仅使用飞利浦新安怡
推荐的附件。
• 仅使用本产品随附的
电源适配器。
• 确保不要将吸乳器
（包括电源适配器）
暴露在高温下，也不
要置于阳光直射处。
• 不要在户外使用。
• 吸乳器内没有用户可
维修部件。切勿尝试
自行打开或修理吸乳
器马达。
• 与母乳直接接触的吸
乳器部件是个人护理
18
ZH-CN
物品，妈妈们不可共
用。
• 吸乳器仍有吸力时，
切勿尝试从乳房上直
接取下吸乳器。关闭
吸乳器，可以用手指
插入乳房和吸乳器主
体之间，然后从乳房
上取下吸乳器。也可
以从吸乳器马达或
硅胶隔膜盖拔下硅胶
管。
• 怀孕期间请勿使用吸
乳器，因为吸乳可能
会导致流产。
• 切勿在您昏昏欲睡或
困倦时使用吸乳器。
• 本产品不打算由肢体
不健全、感觉或精神
上有障碍和缺乏相关
经验和知识的人（包
括儿童）使用，除非
有负责他们安全的人
对他们使用本产品进
行监督或指导。
• 若出现问题或疼痛，
请咨询您的母乳喂养
专家或医生。
• 在易燃易爆空气中或
麻醉性气体与空气，
氧气或氮氧化物混合
的场合下，请勿使用
本产品。
• 尽管本吸乳器符合适
用的
EMC
指令，但是
仍可能受到过量排放
的影响，以及
/
或干
扰更敏感的设备。
注意
• 将电源适配器插头插
入电源插座后，必须
有人看管。
• 切勿将任何异物插入
或塞入吸气口或硅胶
管中。
• 不建议缩短硅胶管。
• 将吸乳器连接至电源
前，请确保当地的电
源电压符合电源适配
器要求。
• 每次使用之前，请将
必要的部件进行清洁
和消毒。
• 清洁吸乳器部件时，
请勿使用抗菌剂或带
简体中文
19
ZH-CN
磨蚀性的清洁剂或去
污剂。
• 切勿将吸乳器马达组
件或电源适配器放入
水中或消毒锅中，否
则可能导致吸乳器永
久损坏。
• 如果产生的吸力令
您感到不适或导致疼
痛，请关闭产品，
并用手指打开乳房和
吸乳器主体之间的密
封，从乳房上取下吸
乳器。也可以从吸乳
器马达或硅胶隔膜盖
拔下硅胶管。
• 如果没有吸出乳汁，
请勿持续吸乳超过
5
分钟。
• 切勿使用其他制造
商生产的或未经飞利
浦新安怡特别推荐的
附件或部件。如果您
使用了此类附件或部
件，则本产品的保修
将会失效。
• 如果硅胶隔膜出现
破损，请勿使用吸乳
器。立即更换备用硅
胶隔膜。请参阅《保
修与服务》章节，了
解如何订购替换部件
的信息。
• 切勿将奶嘴用作安
抚奶嘴。避免长牙期
的宝宝长时间持续扯
咬奶嘴，以防损坏奶
嘴。出于卫生考虑，
建议每
3
个月更换一
次奶嘴；飞利浦新安
怡标准口径奶嘴只能
同飞利浦新安怡标准
口径奶瓶配合使用。
电磁场 (EMF)
本飞利浦产品符合所有有关暴露于
电磁场的适用标准和法规。
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Avent SCF902/11 ユーザーマニュアル
- カテゴリー
- 搾乳器
- タイプ
- ユーザーマニュアル
他の言語で
- English: Avent SCF902/11 User manual
関連論文
その他のドキュメント
-
Medela 101034638-2022-03 ユーザーマニュアル
-
Philips AVENT SCF355 ユーザーマニュアル
-
Tommee Tippee Made for Me Double Electric Breast Pump #1162 ユーザーマニュアル
-
Medela Freestyle Instructions For Use Manual
-
Ardo 9904.425 ユーザーマニュアル
-
Tommee Tippee 431211C Electric Bottle Warmer 取扱説明書
-
-
Petoneer PF007 ユーザーマニュアル
-
Bitspower BPTA-DTMC インストールガイド
-
Oregon Scientific WS912 ユーザーマニュアル
