DT828L
電控參數說明書
ELECTRONIC CONTROL PARAMETER MANUAL
安全指示
1.安全上的注意事項
使用前請詳細閱讀本技術資料與所搭配的縫製機械說明書，配合正確使用
1.1 （1）電源電壓與工作頻率：請遵照馬達與控制箱銘牌所標之規格。
（2）電磁波干擾：請遠離高頻波機器或電波發射器等，以免所產生的電磁波干擾本驅動裝置因而方式
錯誤動作
（3） 接地：為防止雜訊干擾或漏電事故，請做好接地工程（包括縫紉機、馬達、控制箱、定位器）
1.2 拆除馬達或控制箱時，勿帶電拔插；控制箱裡面有危險高電壓，所以關閉電源等 1 分鐘以上放可打
開控制箱蓋
1.3 為保證人身安全，請在維修機械或進行穿針作業時關閉電源
1.4 這個標示符合表示機器安裝時，如有錯誤恐會傷害到人體或機器會受到損壞
所以機器方面有危險性的地方會有此標誌。
這個識別字合表示高壓電等，電氣方面有危險性的地方會有此標誌。
2 操作盒按鍵說明
針距大小調節鍵
電機運行速度調節鍵
恢復出廠設置調整鍵
轉角角度調節鍵
加減鍵
功能鍵
確認鍵 前固縫按鍵
軟啟動按鍵 自由縫按鍵
㇐段定針縫按鍵 自動抬壓腳選擇按鍵
自動觸發按鍵 後固縫按鍵
停針位元選擇按鍵 W 固縫模式按鍵
調試功能按鍵
剪線設定按鍵
電子夾線器設定按鍵 花樣編輯按鍵
固縫花樣按鍵 段式縫花樣自編模式按鍵
漂亮縫紉設置按鍵 手動抬壓腳按鍵
補針按鍵
3. 監控模式
正常情況下，按“P”鍵，將參數調整到 42，按“S”確認，進入到監控模式。按下方相對應的加減鍵顯示相關的監
控參數。按“P”鍵返回到縫紉模式。
顯示序號
項目名稱 預設值
顯示序號
項目名稱 預設值
顯示序號
項目名稱 預設值
顯示序號
項目名稱 預設值
N01 電控版本號 15 N04 腳踏板 AD 值
345
N07 母線電壓 AD 值
630
N10 剪刀位置感應 0
N02 操作盒版本號
3805
N05 上定位角度 84 N08 錯誤代碼記錄
154
N12 膝靠感應 AD 值
500
N03 車縫速度 0 N06 下定位角度 1403
N09 執行時間 7 N13 壓腳感應 AD 值
0
4.模式設置
4.1.調試模式：正常進入縫紉模式後⾧安“M”鍵 3 秒，進入到調試模式，若從該模式退回到正常模式，需安“P”鍵退出進
入正常模式
顯示序號
項目名稱 預設值
顯示序號
項目名稱 預設值
顯示序號
項目名稱 預設值
72 上停針位校正
84 92 編碼器起始角度
128 剪刀動作測試
正常進入縫紉模式後⾧安“M”鍵 3 秒，液晶屏顯示“92”，安 S 鍵進入電機角度測試介面，按“ ”鍵，電機會轉動
幾下，之後液晶屏顯示角度數位，代表電機光柵片的安裝角度為顯示數位，按 S 鍵保存。若要從該模式退回到正常模式，按
“P”鍵退出進入正常模式。
正常進入縫紉模式後⾧安“M”鍵 3 秒，液晶屏顯示“92”，按下方加鍵切換到“72”按 S 鍵進入機械零位元調整介面，
轉動手輪，顯示幕的數值會隨手輪位置變化而變化，按“S”鍵保存當前位置數值為上停針位位置。若要從該模式退回到正常
模式，按“P”鍵退出進入正常模式。
正常進入縫紉模式後⾧安“M”鍵 3 秒，液晶屏顯示“92”， 按下方加鍵切換到“128”按 S 鍵進入剪線動作測試介面，
再按“ ”，剪刀會按照相對應角度動作㇐次（迴圈）。若要從該模式退回到正常模式，按“P”鍵退出進入正常模式。
4.2.密碼模式：⾧按“P”鍵進入密碼模式，液晶屏顯示 0000，按下方對應的加減鍵修改數值，若密碼正確，按“S”鍵後，
可查看高級參數。
4.3.保存出廠參數和恢復出廠參數：⾧按“ ”鍵 5 秒，保存出廠參數完成。⾧按“ ”鍵 5 秒，輸入正確的密碼，恢復出
廠參數完成。
4.4.花樣縫編輯：
正常進入縫紉機模式後⾧按“Patt”鍵，液晶屏顯示“n-01 01”，按“＋ -”鍵切換 n1-n9 花樣，選定要設置的花樣
號後按“S”鍵進入設置，液晶屏顯示“1 1 3.0”，此時可以進行第㇐段的針數、重複次數和針距值得設置，按下方對
應的鍵和“ ”鍵設置各參數值，按 S 鍵保存，P 鍵退出，㇐段設置完成；按“ ”鍵，液晶屏顯示 n01 02，按“S”
鍵進入設置，液晶屏顯示“1 1 3.0”，此時可以進行第二段的針數、重複次數和針距值設置，按下方對應的鍵和“ ”
鍵設置各參數值，按“S”鍵保存，P 鍵退出，二段設置完成；按“ ”鍵，液晶屏顯示 n01 03，按“S”鍵進入設置，
液晶屏顯示“1 1 3.0”，此時若將當前段數的針數設置為零，則縫紉時不進行此段的縫紉；設置完成後按 S 鍵保存，按 P
鍵退出。若從該模式退回到正常模式，按兩次“P”鍵即可。
⾧按 Patt 鍵進入，介面顯示 按 S 鍵進入，介面顯示
花樣編號 N-01 01 1 1 3.0
含義 花樣號 1 號第㇐段花
樣
針數 重複次數 針距大小
編輯方式 下方加減鍵
下方加減鍵 下方加減鍵
⾧按 Patt 鍵進入，介面顯示 按 S 鍵進入，介面顯示
花樣編號 N-01 02 1 1 3.0
含義 花樣號 1 號第二段花
樣
針數 重複次數 針距大小
編輯方式 下方加減鍵
下方加減鍵 下方加減鍵
4.5．花樣縫紉方法：正常進入縫紉模式後按“Patt”鍵，液晶屏顯示“n0”，按下方的加減鍵切換 n1-n9 花樣，選定要縫
紉的花樣號後按“S”鍵確認，此時按選定的花樣進行縫紉；退出花樣縫時，將參數調整到“n0”，按“S”鍵確認，P 鍵退
出進入自由縫模式。
5. 參數表
參數項
中文說明
範圍
初始值
內容值名稱說明與備註
P01 最高轉速（rpm）
100
-
300
0
2500
P02 加速曲線調整（%） 10-100 100
控速器爬升斜率設定
斜率值愈大，速度愈陡；
斜率值愈小，速度愈慢。
P04 起始回縫速度（rpm）
100
-
200
0
1500
P05 終止回縫速度（rpm）
100
-
200
0
1500
P06 連續回縫速度（rpm）
100
-
200
0
1500
P07 慢速起縫速度（rpm）
200
-
150
0
400
P08 慢速起縫針數（針） 0-99 2
P09 自動定針縫速度（rpm）
200
-
300
0
2200 定針縫自動觸發功能打開的速度設定。
P15 補針方式 0-4 5
0
：半針；
1
：㇐針；
2：連續補半針；
3：連續補㇐針；
4: 連續補針, 快速停車
5：倒縫功能
6
：密縫功能
P17 計數器模式選擇 0-1 1 0：P41 項計數器不自動計數
1：P41 項計數器每切線㇐次自動計數
P21
踏板前踩運行位置
30
-
1000
520
P22
踏板回中位置
3
0
-
1000
420
P23
踏板抬壓腳位置
30
-
1000
270
P24
踏板切線位置
30
-
1000
130
P28 連續回縫運動模式選擇 0-1 1
0
：人工，受踏板控制，可任意停止與啟動
1
：自動，輕觸踏板，自動執行回縫動作
P32 加固縫針跡補償 0-200 167
P35
抬壓腳時松線出力功能設
定
0-1 1
0
：抬壓腳時松線出力功能關閉
1
：抬壓腳時松線出力功能開啟
P36 松線/大夾線器切換 0-1 1
0
：切換為大夾線器功能
1
：切換為松線功能
參數項
中文說明
範圍
初始值
內容值名稱說明與備註
P37 撥線/夾線功能設定 0-11 3
0
：功能關閉
1：撥線/挺線功能開啟
2
～
11
：夾線功能開啟，數值越大動作力度越大
P41
計數器顯示
0
-
9999
車縫完成件數顯示；⾧按減號鍵可計數清零；
P44
正常停車力度
1
-
45
16
P49
切線速度（
rpm
）
100
-
350
300
調整切線週期時的主軸電機速度
P52
延遲馬達啟動，保護壓腳
下放時間（
ms
）
10-990 150 踩下時延遲啟動時間，以配合自動抬壓腳放下的確認
P53 半後踏抬壓腳功能取消 0-2 1
0
：關閉；
1：反踏和半反踏都有抬壓腳；
2
：半反踏無抬壓腳，反踏有抬壓腳；
P54
切線動作時間（
ms
）
10
-
990
200
P55
撥
/
掃線動作時間
10
-
990
380
P56 開電後自動找上定位 0-1 0
1
：開啟電源後，自動找到上定位信號後停止
0
：無作用
P57 松線保護時間（s） 1-990 2
松線保持時間後強制關斷，防止電磁鐵⾧時間吸合而發
燙
P58 上定位調整 0-1439 80
上定位調整，數值減少時會提前停針，數值增加時會延
遲停針
P59 下定位調整 0-1439 780
下定位調整，數值減少時
會提前停針，數值增加時會延
遲停針
P60 測試速度（rpm）
100
-
370
0
3500
P61 A 項測試 OFF/ON
OFF 持續運行測試模式
P62
B
項測試
OFF/ON
OFF
全功能啟停測試模式
P63
C
項測試
OFF/ON
OFF
無定位、無功能啟停測試模式
P64
測試執行時間
1
-
250
20
P65
測試停止時間
1
-
250
20
P66
機頭保護開關檢測
0
-
2
0
0
：不檢測；
1
：檢測零信號；
2
：檢測正信號
P67
切線保護開關檢測
ON/OFF
OFF
OF
F
：不檢測；
ON
：檢測
P69 花樣自由縫速度
100
-
200
0
1500
P71
補針針距
0
-
164
3
P72 上定位快捷調整 0-1439
調整上停針位元，顯示的數值會隨手輪位置變化而變
化，
短
按
S
鍵可保存當前位置（數值）為上停針位。
P73 下定位快捷調整 0-1439
調整下停針位元，顯示的數值會隨手輪位置變化而變
化，
短
按
S
鍵可保存當前位置（數值）為下停針位。
P74
正縫針距補償
0
-
100
50
P75
倒縫針距補償
0
-
100
50
P78
夾線器起夾角度
10
-
3
59
180
P79
夾線器結束角度
10
-
359
250
P80
進刀角度
5
-
359
80
第㇐次進度角度（下定位為
0
°計算）
P81
第㇐次退刀角度
5
-
359
160
P82
第二次退刀角度
5
-
359
220
第㇐次退刀角度（下定位為
0
°計算）
P87
撥
/
掃線回程延遲時間
10
-
990
50
P92 編碼器起始角度
在參數設定介面，短按補針鍵，電機將自動運行，讀取
並顯示編碼器起始角度。出廠已設置，請勿隨意更改，
否則將導致控制箱、電機出現異常或損壞。
P93
半反踏功能延
遲時間
10
-
990
200
P99
大夾線器電流
0
-
200
60
P100
大夾線器啟夾時間
0
-
990
120
P101
松線開始角度
1
-
359
30
P102
松線結束角度
1
-
359
180
P103
大夾線器啟夾電流
0
-
300
5
P109
撥
/
掃線前延遲時間（
ms
）
5
-
990
5
找到上定位後進入撥
/
掃線動作前的間隔時間
P110
切線回程時間（
ms
）
60
-
990
60
P112
無鳥巢鉤線前延時
0
-
990
100
P113
無鳥巢鉤線動作時間
0
-
990
30
P114
無鳥巢鉤線返程時間
0
-
990
30
P115
無鳥巢鉤線占空比
1
-
100
30
P116
無鳥巢吸氣時間
0
-
5000
1000
P117
無鳥巢挺線占空比
0
-
100
30
P122
膝靠啟動
AD
值
0
-
1023
600
參數項
中文說明
範圍
初始值
內容值名稱說明與備註
P125 中途抬壓腳高度補償 0-160 80
以
80
為
0
補償，往大調為正補償，壓腳高度升高，往
小調為負補償，壓腳高度降低
P128 切線功能測試
在參數設定介面，短按切線鍵，切線將按照設定的角度
進行動作。
P129
倒縫步進電
機零點校正
0
-
200
50
P130
切線步進電機零點校正
0
-
200
50
P131
正常針距
0
-
164
76
正常縫製模式下的針矩
P132
加密針距
0
-
164
52
P133
加寬針距
0
-
164
100
P134
第二次切線距離（後動作）
0
-
200
145
P136
最高壓腳高度
0
-
150
135
P137
第㇐次切線距離（先動作）
0
-
200
100
P140
第二次退刀速度
20
-
250
300
P141
第㇐次退刀速度
20
-
400
350
切線過程
第㇐段速度
P142
第㇐次進刀速度
20
-
400
350
切線過程第二段速度
P146
壓腳速度
20
-
300
200
P153
漂亮縫針距
0
-
60
15
P154 漂亮縫速度
100
-
100
0
500
P155
手動補針按鍵功能切換
0
-
1
0
0
：補針功能；
1
：密縫功能
P159
漂亮縫方向
0
-
1
0
0
：正縫；
1
：倒縫
P160
漂亮縫針數
0
-
12
0
參數值為
0
時，漂亮縫功能關閉
P170
手動按鍵
N
的補針針距
0
-
7
P171
手動按鍵
L
的補針針距
0
-
7
P173
手動按鍵
R
的補針針距
0
-
7
P174 手動按鍵 N 的功能選擇 0-6 6
0
：功能關閉
1：補半針
2：補㇐針
3：連續補半針
4：連續補㇐針
5：在車縫中或中途停止時具有倒縫動作
6
：密縫功能
P175 手動按鍵 L 的功能選擇 0-6 0
0
：功能關閉
1：補半針
2：補㇐針
3：連續補半針
4：連續補㇐針
5：在車縫中或中途停止時具有倒縫動作
6
：密縫功能
P176 手動按鍵 R 的功能選擇 0-6 0
0
：功能關閉
1：補半針
2：補㇐針
3：連續補半針
4：連續補㇐針
5：在車縫中或中途停止時具有倒縫動作
6
：密縫功能
P177
正向
1mm
針距基準值
0
-
300
58
P178
反向
1mm
針距基準值
0
-
300
47
P179
正向
2mm
針距基準值
0
-
300
100
P180
反向
2mm
針距基準值
0
-
300
85
P181
正向
3mm
針距基準值
0
-
300
145
P182
反向
3mm
針距基準值
0
-
300
128
P183
正向
4mm
針距基準值
0
-
300
185
P184
反向
4mm
針距基準值
0
-
300
160
P185
正向
5mm
針距基準值
0
-
300
222
P186
反向
5mm
針距基準值
0
-
300
190
P187
正向
6mm
針距基準值
0
-
300
262
P188
反向
6mm
針距基準值
0
-
300
228
P189
正向
7mm
針距基準值
0
-
300
300
P190
反向
7mm
針距基準值
0
-
300
252
P213
針間距離
3.2
-
25.4
6.4
P214
自由縫轉角角度
30
-
140
90
P215 定針縫轉角模式 0-3 0
0
：多段縫
1
：左轉
參數項
中文說明
範圍
初始值
內容值名稱說明與備註
2
：右轉
3
：機械轉角
P216 轉角針數模式 0-1 0
0
：針距平分
1
：大小針距
P217 轉角自動模式 0-2 1
0
：受踏板控制
1：自動轉角
2
：機械轉角
P218
轉角落針時間
0
-
50
15
P219
左右機針分離電磁鐵占空
比
0-100 40
P220
左右分離電磁鐵保護時間
0
-
50
15
注：參數初始值僅供參考，實際參數值以實物為准。
6 錯誤代碼表
錯誤碼
內容 對策
E01 1.電源 ON 時，主電壓檢測過高
2.供應電源電壓過高時
關閉系統電源，檢測供應電源電壓是否正確。（或是否超
過使用規定的額定電壓）。
若正確，請更換控制箱並通知售後服務。
E02 1.電源 ON 時，主電壓檢測過低
2.供應電源電壓過低時
關閉系統電源，檢測供應電源電壓是否正確。（或是否低
於使用規定的額定電壓）。
若正確，請更換控制箱並通知售後服務。
E03 操作面板與 CPU 傳輸通信異常
關閉系統電源，檢查控制台的連線是否鬆動或脫落，將
其恢復正常後重啟系統。若仍不能正常工作，請更換控
制箱並通知售後服務。
E05 控速器接觸異常
關閉系統電源，檢查控速器接頭是否鬆動或脫落，將其
恢復正常後重啟系統。若仍不能正常工作，請更換控速
器並通知售後服務。
E07
1.馬達插頭配線接觸不良導致不轉
2.車頭機構鎖死或馬達皮帶異物捲入卡死
3.加工物過厚，馬達扭矩不足無法貫穿
4.模組驅動出力異常
轉動機頭手輪觀察是否卡住。如卡住則先排除機械故障。
如轉動正常，檢查電機編碼器接頭和電機電源線接頭是
否鬆動。如有鬆動請修正。
如接觸良好，檢查供應電源電壓是否異常或轉速設置過
高。如有請調整。
若仍不能正常工作，請更換控制箱並通知售後服務。
E08 功能步進電機異常
查看
P42
項參數裡
N14
的數值，
0
：通信異常，
2
：倒縫
步進過流 4：倒縫步進開機找不到原點 16：切線步進過
流 32：切線步進找不到原點
關閉系統電源，觀察步進電機是否卡住。如卡住則先排
除機頭機械故障。
如正常，檢查步進電機介面是否鬆動或脫落，將其恢復
正常後重啟系統。
若仍不能正常工作，請更換控制箱並通知售後服務。
E10
電磁鐵過流保護
關閉系統電源，檢查電磁鐵（電磁閥）是否損壞或短路。
E09
E11 定位信號異常
關閉系統電源，檢查電機編碼器介面是否鬆動或脫落，
將其恢復正常後重啟系統。若仍不能正常工作，請更換
電機並通知售後服務。
E13
電力模組過熱保護
關閉系統電源，檢查電磁鐵連接或電
磁鐵是否損壞
E14 編碼器信號異常
關閉系統電源，檢查電機編碼器介面是否鬆動或脫落，
將其恢復正常後重啟系統。若仍不能正常工作，請更換
電機並通知售後服務。
E15 電力模組不正常過流保護
關閉系統電源，再重新開啟。若仍不能正常工作，請更
換控制箱並通知售後服務。
E16 切線步進電機異常
關閉系統電源，檢查切線機構是否回到正確位置；檢查
切線的設置是否錯誤。
E17 機頭保護開關沒到正確位置 關閉系統電源，檢查機頭是否掀開，控制箱內滾珠開關
是否移位元或損壞。
E20 電機啟動失敗（電角度錯誤）
關閉系
統電源，檢查電機編碼器介面和電機電源介面是
否鬆動或脫落，將其恢復正常後重啟系統。若仍不能正
常工作，請更換控制箱並通知售後服務。
Safety Instruction
1. Safety precautions
Before ues, please read this technical data and the manual of the matching sewing machine in detail,
and ues it correctly
1.1 (1)Power supply voltage and working frequency: please follow the specifications marked on the
nameplate of the motor and control box.
(2).Electromagnetic wave interference: Please stay away from high-frequency wave equipment or
radio wave transmitters, etc., so as to avoid the generated electromagnetic waves from interfering with
the drive and thus operating in a wrong way.
(3).Grounding: To prevent noise interference or leakage accidents, please do a grounding
project(including sewing machine, motor, control box, positioner).
1.2.When disassembling the motor or control box, do not pull it out with power on; there is dangerous
high voltage inside the control box, so after turning off the power, wait 1 minute or more to open the
control box coner.
1.3.In order to ensure personal safety, please turn off the power when servicing machinery or
performing needle insertion work.
1.4.This mark is consistent with that when the machine is installed, if it is wrong,it may hurt the
human body or the machine will be damaged.
So there is this sign on the machine where there is danger.
This sign conforms to the sign that there is high voltage electricity, etc., where there is danger in
electrical aspects.
2 Key description
Stitch length setting
Speed increase/ Speed decrease
Reset
Angle adjusting key
Parameter increase/Parameter
decrease Function parameter edit
Confirm key Start back-tacking sewing
Slow launch setting Free sewing
A fixed stitch button Automatic presser foot lifting setting
Auto function End back-tacking sewing
Needle stop position selection Consecutive reverse sewing
M key
Thread trimming
Electronic wire clamp adjusting key Pattern freedom sewing setting
Pattern backing-tacking setting
Pattern constant-stitch sewing
setting
Tight seam setting Half anti-side trample foot lifting
Lift or fill up needle
3.Monitor mode
Under normal circumstances,press the “P” key to adjust the parameter to 42,press “S” to confirm and enter the
monitering mode.Press the corresponding plus and minus keys to display related monitoring parameters.Press P to reture
to sewing mode.
Serial number
Name Defaults
Serial nuber
Name Defaults
N01 Electronic contro lversion serial
nuber
15 N07 Bus voltage AD value 630
N02 Selector box version nuber 3805 N08 Error code record 154
N03 Sewing speed 0 N09 Operation hours 7
N04 Foot pedal AD value 345 N10 Scissor position sensing
0
N05 Upper positioning angle 84 N12 Knee-sensory AD 500
N06 Lower positioning angle 1403 N13 Presser foot seneor AD
0
4.Mode setting
4.1 Debug mode: After entering the sewing mode normally, press and hold the “M” key for 3 seconds to enter the
debug mode. To exit from this mode to normal mode, press the “P” to exlt into the normal mode
Serial number
Name Defaults
Serial number
Name Defaults
72 Correction of needle position
84 92 Encoder starting angle
128 Scissor action test
After entering the sewing mode normally, long press the “M” key for 3 seconds, the LCD screen displays “92”
press the S key to enter the motor angle test interface, press the “ ” key, the motor will turn a few times, then the LCD
The screen displays the angle number, which means that the installation angle of the motor grating is the displayed
number. Press the S key to save. To exit from this mode to normal mode, press "P" key to exit into normal mode
After normally entering the sewing mode, press and hold the "M" key for 3 seconds, the LCD screen displays "92",
press the plus and minus keys to switch to "72", press the S key to enter the mechanical zero adjustment interface, turn the
handwheel, the displayed value will be handy The wheel position changes and changes. Press the "S" key to save the
current position (value) as the upper stop needle position. To return to normal mode from this mode, press the "P" key to
exit into normal mode.
After entering the sewing mode normally, long press the "M" button for 3 seconds, the LCD screen displays "92", the button
switches to "128", press the S button to enter the thread trimming action test interface, and then press “ ”, the scissors
will act once according to the desired angle (Cycle), if you want to return to normal mode from this mode, press P key to exit
into normal mode.
4.2. Password mode: Long press the "P" key to enter the password mode, the LCD displays 0000, and the
corresponding addition and subtraction modify the value below. If the password is correct, press the "S" key to view the
advanced parameters.
4.3. Save factory parameters and restore factory parameters:Press and hold the “ ” key for 5 seconds to save the
factory parameters. Press and hold the“ ” key for 5 seconds to restore the factory parameters.
4.4.Pattern sewing edit:
After entering the sewing mode normally, long press the "Patt" key, the LCD screen displays "n-01 01", press the
+-key to switch the n1-n9 pattern, select the pattern number to be set,and press the "S" key to enter the setting, the
liquidThe crystal screen displays "1 1 3.0". At this time, you can set the number of stitches, the number of repetitions and
the distance between stitches in the first segment. Press the corresponding key below and the
“ ”, key to set each parameter value. Press the S key to save.P key to exit, a period of setting is completed; press
the“ ”key, the LCD screen displays n-01 02, press the "S" key to enter the setting, the LCD screen displays "1 1 3.0",
at this time you can perform the second Set the number of stitches, repeat times and stitch length of the segment, press the
corresponding key and“ ”key to set each parameter value, press the "S" key to save, P key to exit, the second
segment setting is completed; press the“ ” key, The LCD screen displays n-01 03, press the "S" key to enter the
setting, the LCD screen displays "1 1 3.0", if the number of stitches of the current segment is set to zero at this time, the
sewing of this segment will not be performed during sewing; the setting is completed Then press S to save and press P to
exit. To return to normal mode from this mode, press the "P" key twice.
Long press the Patt key to enter, the interfa ce
displays
Press S to enter, the interface displays
Pattern number N-01 01 1 1 3.0
meaning Pattern number No.1 first pattern Contacts Repeat times Stitch size
The way
Add and subtravt
keys below Plus minus keys
Plus minus keys
Long press the Patt key to enter, the interfa ce
displays
Press S to enter, the interface displays
Pattern number N-01 02 1 1 3.0
meaning Pattern number No.1 first pattern Contacts Repeat times Stitch size
The way
Add and subtravt
keys below Plus minus keys
Plus minus keys
4.5.Pattern sewing method:Press the " " key after entering the sewing mode normally, the LCD screen displays "n0",
press the plus and minus keys to switch the n1-n9 pattern, select the pattern number to be sewn and press the "S" key to
confirm, then press the selected pattern Perform sewing; when exiting the pattern sewing, adjust the parameter to "n0",
press the "S" key to confirm, and the P key to exit to enter the free sewing mode.
5. User parameter
No. Items Range Default
Description
P01 Maximum sewing speed
(rpm) 100-3000 2700 Maximum speed of machine sewing
P02 Set accelerated curve (%) 10-100 100
Set the acceleration slope
The greater the slope value, the steeper the speed; the
smaller the slope value, the slower the speed
P03 Needle UP/ DOWN UP/DN DN UP: Needle stops at up position
DN: Needle stops at down position
P04 Start back-tacking speed
(rpm) 200-2000 1500
P05 End back-tacking speed
(rpm ) 200-2000 1500
P06 Bar-tacking speed (rpm) 200-2000 1500
P07 Soft start speed (rpm ) 200-1500 1500
P08 Stitch numbers for soft start
1-15 2
P09 Automatic constant-stitch
sewing speed (rpm) 200-3000 2200 Speed adjustment for automatic constant-stitch sewing
P15 Manual Switch A 0-6 3
0: OFF
1: Half stitch
2: One stitch
3: Continuous half stitch
4: Continuous one stitch
5: Back-tacking when machine stop or pause
6: Tight seam function
P21 The position of the pedal for
accelerating 30-1000 520
P22 The position of the pedal for
the stop 30-1000 420
P23 The position of the pedal for
presser foot lifting 30-1000 270
P24 The position of the pedal for
thread trimming 30-500 130
P32 Bar-tacking compensation 5
0-200 190
Stitch compensation for bar-tacking A (C) section, 0~200
action gradually delay; the large value, the longer of the A (C)
section last stitch; the shorter of the B (D) section first stitch.
P35
Thread tension releasing
function setting when
presser foot lifting action
0-2 1
0: OFF
1: Thread tension releasing output function ON when presser
foot lifting, thread tension releasing output function OFF when
stopover
2: Full function
P36 Thread tension releasing
function selection 0-1 1 0: OFF
1: ON
P37
Thread wiping function /
Thread clamping function
selection
0-11 1
0 : OFF
1: Thread wiping function.
2-11: Thread clamping Function and the strength of automatic
thread clamping.
P41 Thread trimming counter
display 0-9999 0 Display the quantity of finished sewing piece.
Long-press “-”
key to clear the count
P44 Brake strength during
stopover 1-45 16
P49 Thread trimming speed
(rpm) 100-250 200 Adjust thread trimming speed
P52
Delay the start of the motor
to protect the lowering time
of presser foot (ms)
10-990 120 Delay the start time, with automatic presser foot down.
P53
Half back pedaling lifting
presser foot function to
cancel
0-2 1
0: OFF
1: Back pedaling and half back pedaling with lifting presser
foot
2: Half back pedaling without lifting presser foot, back
pedaling with lifting presser foot
P54 Thread trimming action time
(ms) 10-990 200
No. Items Range Default
Description
P55 Thread wiping action time
(ms) 10-990 50
P56 Power on and positioning 0-1 0 0: Always not to find the up needle position
1: Always to find the up needle position
P57 Presser foot solenoid
protection time (s) 1-60 60 Forced shutdown after hold time to prevent the electromagnet
from being hot for a long time
P58 Up needle position
adjustment 0-359 200
Up position adjustment, the needle will advance stop when
the value decreased, the needle will delay stop when the
value increased.
P59 Down needle position
adjustment 0-359 10
Down position adjustment, the needle will advance stop when
the value decreased, the needle will delay stop when the
value increased.
P60 Testing speed (rpm ) 100-3000 2200 Setting testing speed.
P61 Testing A ON/OFF OFF Continuous running testing.
P62 Testing B ON/OFF OFF Start and stop testing with all functions.
P63 Testing C ON/OFF OFF Start and stop testing without all function.
P64 Test run time 1-250 30
P65 Test stop time 1-250 10
P66 Machine protection switch
selection 0-1 1 0: Disable
1: Testing zero signal
P69 Pattern freedom sewing
speed 100-1800 1500
P70 Type 1-60 28
P71 Correction stitches distance
of manual button A 0-5.0 0.3
P72 Up needle position
adjustment 0-359 200
Adjust up needle position, the displayed value will change
with the position of the handwheel, press "S" key to save the
current position (value) as up needle position.
P73 Down needle position
adjustment 0-359 10
Adjust down needle position, the displayed value will change
with the position of the handwheel, press "S" key to save the
current position (value) as down needle position.
P74 Tacking stitch length
compensation -100~100 0
P75 Back-tacking stitch length
compensation -100~100 0
P77
Opportunity point of
back-tacking for end
back-tacking in high speed
in free sewing mode
20-350 125
P78 The start angle of thread
clamping 5-359 180
P79 The stop angle of thread
clamping 5-359 230
P80 The angle of trimming first
engage 0-359 60
P81 The angle of trimming first
retract 1-359 160
P82 The angle of trimming
second retract 0-359 220
P87 Wiping thread return delay
time 10-990 50 Make sure the wiper returns to its original position
P92 Correct the electrical angle
of motor
Reading the initial Angle of encoder, the factory default was
set, please do not change the values (parameter value cannot
be changed manually, random change it will result the control
box and motor abnormal or damaged).
P93 The starting time of the half
back pedaling function (ms)
10-900 100
P99 Starting tight seam stitch
length 0-5.0 0.5
P100 Direction of starting tight
seam 0-1 0
P101 The start angle of thread
tension releasing 1-359 160 Thread tension releasing start angle (defined as 0°under
calculation)
No. Items Range Default
Description
P102 The stop angle of thread
tension releasing 1-359 250 Thread tension releasing end angle (defined as 0°under
calculation, must be greater than P101 parameter value)
P103 Thread tension releasing
strength 1-80 30
P109
The delay time before
thread
wiping
5-990 5 Interval time before entering thread wiping action after finding
the upper positioning
P110 Trimming back time (ms) 60-990 100 Make sure the thread trimming device returns to its original
position
P111 Clamp function without any
thrum switch 0-1 0
P112
The delay time before hook
thread with clamp function
without any thrum
0-990 60
P113
The hook thread action time
with clamp function without
any thrum
0-990 70
P114
The return back time of
hook thread with clamp
function without any thrum
0-990 30
P115
Duty cycle for hook thread
with clamp function without
any thrum
0-100 70
P116 The suction time for clamp
function without any thrum 0-5000 500
P117
Duty cycle for pull thread
with clamp function without
any thrum
0-100 70
P118
Function selection of
manual back-tacking button
in pattern mode
0-1 0
0: If you press it for a long time, you can sew the pattern
backwards.
1: If click, it will clear the current number of pattern stitches
and restart. It is used for corner sewing to avoid protruding
one stitch.
P122 Kneeling device starting AD
value 0-1023 600
P125 The height of the presser
foot lifting in the middle 0-320 80
Set 80 as 0 compensation, go to the major adjustment for
positive compensation, the height of the presser foot will
increase, go to the minor adjustment for the negative
compensation, the height of the presser foot will decrease.
P129 Back-tacking stepping
motor zero-point correction -500~500 0
P131 Normal stitch length 0-5.0 4.0
P132 Manual close stitches
distance 0-5.0 2.0
P134 The distance of trimming
first retract 0-115 85
P135
The lowest presser foot lift
height of electric
knee-control
0-300 45
P136 The highest of presses foot
lift highness 0-300 200
P137 The distance of trimming
first engage 0-200 170
P140 The speed of trimming
second retract 20-1000 300
P141 The speed of trimming first
retract 20-1000 450
P142 The speed of trimming first
engage 20-1000 450
P143 Tight seam mode selection 0-3 0
0: OFF
1: Starting tight seam
2: Ending tight seam
3: Full function
No. Items Range Default
Description
P144 Tacking stitch length
compensation in high speed
-100～100
0
P145 Back-tacking stitch length
compensation in high speed
-100～100
0
P146 Presser foot speed 20-400 250
P148
When the main shaft motor
is running, the highest
presser foot lift height of
electric knee-control
0-300 100
P150 Presser foot motor steady
current 0-25 15
P152 Presser foot motor
maximum current 0-65 50
P153 Ending tight seam stitch
length 0-5.0 0.5
P154 Ending tight seam speed 100-2000 1000
P159 Direction of ending tight
seam 0-1 0 0: Forward
1: Backward
P160 Ending tight seam stitch
number 0-12 2
P165 Stitch counter mode
selection 0-4 0
0: Do not count
1. Increase cycle count
2. Decrease cycle count
3. Increase count, alarm after the count is full, need to press
the clear key to start recounting
4. Decrease count, alarm after the count is full, need to press
the clear key to start recounting
P166 Upper limit of stitch counter
(stitch) *10 0-9999 500
P170 Correction stitches distance
of manual button B 0-5.0 0.3
P171 Correction stitches distance
of manual button C 0-5.0 0.8
P173 Correction stitches distance
of manual button D 0-5.0 1.8
P174 Manual Switch B 0-6 5
0: OFF
1: Half stitch
2: One stitch
3: Continuous half stitch
4: Continuous one stitch
5: Back-tacking when machine stop or pause
6: Tight seam function
P175 Manual Switch C 0-6 2
0: OFF
1: Half stitch
2: One stitch
3: Continuous half stitch
4: Continuous one stitch
5: Back-tacking when machine stop or pause
6: Tight seam function
P176 Manual Switch D 0-6 2
0: OFF
1: Half stitch
2: One stitch
3: Continuous half stitch
4: Continuous one stitch
5: Back-tacking when machine stop or pause
6: Tight seam function
P177 1mm forward stitch length
reference value setting 0-2000 58
P178 1mm backward stitch length
reference value setting 0-2000 47
P179 2mm forward stitch length
reference value setting 0-2000 100
P180 2mm backward stitch length
reference value setting 0-2000 85
P181 3mm forward stitch length 0-2000 145
No. Items Range Default
Description
reference value setting
P182 3mm backward stitch length
reference value setting 0-2000 128
P183 4mm forward stitch length
reference value setting 0-2000 185
P184 4mm backward stitch length
reference value setting 0-2000 160
P185 5mm forward stitch length
reference value setting 0-2000 222
P186 5mm backward stitch length
reference value setting 0-2000 190
P187 6mm forward stitch length
reference value setting 0-2000 262
P188 6mm backward stitch length
reference value setting 0-2000 228
P189 7mm forward stitch length
reference value setting 0-2000 300
P190 7mm backward stitch length
reference value setting 0-2000 252
P213 Needle tip distance 3.2-25.4 6.4
P214 Angle of free seam rotation 30-140 90
P215 Fixed stitch angle mode 0-3 0
0：Multisegment seam
1：Left-handed rotation
2：Dextroversion
3：Mechanical corner
P216 Corner stitch mode 0-1 0 0：The needle pitch is evenly divided
1：The large and small needle pitch
P217 Corner auto mode 0-2 1
0：Automatic corner
1：Controlled by pedal
3：Mechanical corner
P218 Turn the corner needle time
0-50 15
P219
Duty ratio of left and right
needle separation
electromagnets
0-100 40
P220
Protection time of left and
right separation
electromagnets
0-50 15
Note: the initial value of parameters is for reference only, and the actual value of parameters is subject to the real object.
6. Error code list
Error Code
Problem Measure
E01 Over-voltage
Turn off the system power and check whether the power supply
voltage is correct. (Or whether it exceeds the
specified rated voltage).
E02 Low-voltage
Turn off the system power and check whether the power supply
voltage is correct. (Or whether it is lower than the specified rated
voltage).
E03
Abnormal communication
between the main CPU and the
panel CPU
Turn off the power and check whether the connector is connected to
the operation panel and the cable condition.
E05
Speed control unit connection
is abnormal
Please turn off the power and check whether the connector is
connected to the speed controller and the
cable condition.
E07 Main shaft motor rotating
abnormally
Please rotate handwheel to check if the spindle motor is locked.
Check if the encoder cable of the motor and the power cable of the
motor are connected to the connector. Check if the power supply
voltage is normal and whether the sewing speed is too high.
E10 Solenoid over-current
protection
Turn off the system power supply, please check the solenoid
(solenoid valve) connector or solenoid (solenoid valve) is broken or
not.
E09
E11 Positioning signal error
Turn off the machine, please check if the encoder in bad connection
or is too loose. To get it right and turn on. If there are still errors,
please replace the control box and call for
customer service.
E14 Encoder signal error.
Turn off the sys
tem power supply, please check motor encoder
connector if loose or fall off, renew to normal then restart system.
E15
Main shaft motor overcurrent
error
Turn off the power, and then turn it on again.
E17 Head fall error
Please raise machine head and turn
on the power again. Check if the
head down switch is damaged.
E20
Main shaft motor rotating
abnormally at startup
Turn off the power and check whether the encoder cable of the motor
and the power cable of the motor are connected to the connector.
E80
Ab
normal communication
between the main CPU and the
driver CPU
Turn off the power, and then turn it on again.
E82
Back
-
tacking step
ping
motor
overcurrent
Turn off the power, and then turn it on again.
E84
Back
-
tacking step
ping
motor
encoder Z signal abnorm
al
Turn off the power and check whether the encoder cable of the
step
ping
motor is connected to the connector.
E85
Back
-
tacking step
ping
motor
encoder AB signal abnormal
Turn off the power and check whether the encoder cable of the
step
ping
motor is conne
cted to the connector.
E86
Back
-
tacking step
ping
motor
failed to start
Turn off the power and check whether the encoder cable of the motor
and the power cable of the motor are connected to the connector.
E87
Back
-
tacking step
ping
motor
locked
-
rotor
Please check if the stepping motor is locked.
E92 Thread trimming (presser foot)
stepping motor overcurrent
Turn off the system power and observe whether the thread trimming
(presser foot) stepping motor is stuck. If it is stuck, remove the
mechanical failure of the machine head first. If it is normal, check if
the thread trimmer (presser foot) stepping motor interface is loose or
fall off, restore it to normal and restart the system.
E94
Thread trimming (presser foot)
stepping motor can’t find
zero-point
Turn
off the system power and observe whether the thread trimming
(presser foot) stepping motor is stuck. If it is stuck, remove the
mechanical failure of the machine head first. If it is normal, check
whether the thread trimming (presser foot) stepping motor encoder
interface is loose or falling off, and whether there is oil on the encoder
code disk. If there is any oil, please clean it up, restore it to normal
and restart the system.
E95
Thread trimming (presser foot)
stepping motor encoder signal
is abnorma
l
Turn off the system power, check if the thread trimming (presser foot)
stepping motor encoder interface is loose or fall off, restore it to
normal and restart the system.
E96 Thread trimming (presser foot)
stepping motor failed to start
Turn off the pow
er of the system, check whether the wire trimming
(presser foot) stepping motor power cord interface and encoder
interface are loose or fall off, and restart the system after returning it
to normal.
E97 Thread trimming (presser foot)
stepping motor stalling
Turn off the system power and observe whether the thread trimming
(presser foot) stepping motor is stuck. If it is stuck, remove the
mechanical failure of the machine head first. If it is normal, check
whether the wire trimming (presser foot) stepping motor power cord
interface and encoder interface are loose or fall off, restore them to
normal and restart the system.
由於對產品的改良及更新，本產品使用說明書中與零件圖之產品及外觀的修改恕不事先通知 !
The specification and/or appearances of the equipment described in this instruction
book & parts list are subject to change because of modification which will without
previous notice.
DT828L.DEC.2021
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
他の言語で
- English: Siruba DT828L Owner's manual
関連論文
その他のドキュメント
-
Noctua NM-AMB13 インストールガイド
-
-
ZOJE ZJ8000E SERIES ユーザーマニュアル
-
-
ESAB A6 PEK Control Panel ユーザーマニュアル
-
Yamaha XS6 データシート
-
-
KTM 990 Adventure AU GB 2012 取扱説明書
-
-
3M Allergen Protein ELISA Kit 取扱説明書
