APPA sFLEX 18A ユーザーマニュアル

LIMITED

WARRANTY

YEARS

User Manual / 使用說明書 / 使用说明书

ユーザーマニュアル

Руководство пользователя

sFLEX 18A

RU

EN

TC

SC

JP

Flexible Current Probe Meter

軟性電流探針表

软性电流探针表

フレキシブル電流プローブ

Гибкая токовая петля

Read First

!

!Safety Information

To ensure safe operation and service of the meter,

follow these instructions. Failure to observe warnings

can result in severe INJURY or DEATH.

WARNING identifies hazardous conditions and

actions that could cause bodily harm or death.

- If the equipment is used in a manner not specified

by the manufacturer, the protection provided by the

equipment may be impaired.

- Always use proper terminals and range for

measurements.

- Always use proper terminals, switch position, and

range for measurements.

- To reduce the risk of fire or electric shock, do not

use this product around explosive gas or in damp

locations.

- Verify the Meter operation by measuring a known

voltage. If in doubt, have the Meter serviced.

- Do not apply more than the rated voltage, as

marked on Meter, between terminals or between

any terminal and earth ground.

- To avoid false readings that can lead to electric

shock and injury, replace battery as soon as low

battery indicator appears.

- Avoid working alone so that assistance can be

rendered.

- Do not use the Meter if the Meter is not operating

properly or if it is wet.

- Individual protective device must be used if

hazardous live parts in the installation where the

measurement is to be carried out could be

accessible.

- When using test leads or probes, keep your fingers

behind the finger guards.

Warning

!

EN

sFLEX 18A

1

- Use caution with voltages above 30 Vac rms, 42 Vac

peak, or 60 Vdc. These voltages pose a shock hazard.

- Remove test lead from Meter before opening the

battery door or Meter case.

- DO NOT USE the test leads when the internal white

insulation layer is exposed.

- DO NOT USE the test leads above maximum ratings

of CAT. environment, voltage and current, that are

indicated on the probe and the probe tip guard cap.

- DO NOT USE the test leads without the probe tip

guard cap in CAT III and CAT IV environments.

- Probe assemblies to be used for MAINS measure

ments shall be RATED as appropriate for MEAS

UREMENT CATEGORY III or IV according to IEC

61010-031 and shall have a voltage

RATING of at least the voltage of the circuit to be

measured.

- Disconnect circuit power and discharge all high

voltage capacitors before testing resistance, continuity,

diodes, or capacitance.

- Do not use a flexible current sensor if the inner copper

wire of the insulation of the flexible cord is visible.

- De-energize the installation under test or wear suitable

protective clothing during fitting and removal of the

Flexible Current Probe.

- Do not apply around or remove from UNINSULATED

HAZARDOUS LIVE conductors, which may render

electric shock, electric burn, or arc flash.

!

Caution

CAUTION identifies conditions and actions that could

damage the Meter, the equipment under test, or cause

permanent loss of data.

- Remove the batteries if the Meter is not used for an

extended period of time, or if stored in temperatures

above 50 °C. If the batteries are not removed, battery

leakage can damage the Meter.

- Do not expose Meter to extremes in temperature of

high humidity.

EN

sFLEX 18A

2

Symbols on Meter and in this Manual

EN

sFLEX 18A

!

See instruction manual

WARNING. HAZARDOUS VOLTAGE.

Risk of electric shock.

Caution

Do not apply or remove clamp from

HAZARDOUS LIVE conductors

AC (Alternating Current or Voltage)

DC (Direct Current or Voltage)

Both AC and DC

CAT IV

CAT III

IEC Overvoltage Category

CAT III equipment is designed to protect

against transients in equipment in fixed

equipment installations, such as

distribution panels, feeders and short

branch circuits, and lighting systems in

large buildings.

CAT IV equipment is designed to protect

against transients from the primary

supply level, such as an electricity Meter

or an overhead or underground utility

service.

Earth ground

Equipment protected by double or

reinforced insulation.

Battery capacity

Wireless transmission

Conforms to European Union directives.

Do not discard this product or throw

away.

3

Meter Description

1. Clamp lock mechanism

2. LCD display

3. Function buttons

4. V-Ω input terminal

5. COM input terminal

EN

sFLEX 18A

4

LCD Description

Power On / Off

The Meter displays battery capacity when powering

up.Please replace the battery when 0% is shown.

1. Meter status symbols

2. Battery capacity symbols

3. Large scale LCD readout

4. Function unit symbols

5. Hold symbol

6. Sub LCD readout

EN

sFLEX 18A

5

Disable Auto Power Off

Press > 2Sec

Auto Power Off

If no any operation in Meter, it will auto power off after

20 minutes.

To disable APO, push and hold the Bluetooth button,

then turn the Meter power on.

EN

sFLEX 18A

6

AC Current Measurement

!

Warning

The barrier on the JAW is indicating the limit of safe

access of the hand held part, do not hold over the

barrier when in normal use.

!Barrier for

Hand Guard

Unlock / Lock Clamp Jaw

Turn the clamp lock counter-clockwise to release the

flexible clamp. Fully enclose only one conductor of the

device under test with the flexible clamp probe.

Re-secure the clamp lockafter clamping around a

single conductor.

EN

sFLEX 18A

7

Position Error

When measuring current, move a single cable in the

center of the flexible clamp jaw. It can make less the

position error.

Voltage & Resistance Measurement

• When connecting the test leads to the DUT (Device

Under Test) connect the common test leads before

connecting the live test leads; When removing the test

leads, remove the live test leads before removing the

common test leads.

• Do not use the LoZ mode to measure voltages in

circuits that could be damaged by this mode’s low

impedance (approx. 4kΩ).

EN

sFLEX 18A

8

Data Hold

EN

sFLEX 18A

9

The Meter uses low-power (BLE) v4.0 wireless

technology to transfer the real-time data. To use the

RF communication link on Android or iOS devices,

install App from the below QR code.

Backlight

The RF communication range: Open air up to 10 m

APPA Connect

on Apple App Store

APPA Connect

on Google Play

To turn On / Off the backlight, press the backlight

button once.

Worklight

To turn On / Off the worklight, push and hold the

backlight button

>1sec.

EN

sFLEX 18A

10

Battery Replacement

Maintenance

Verify the Meter’s operation by measuring a known

voltage. If in doubt, have the Meter serviced. Do not

attempt to repair this Meter. It contains no user

serviceable parts. Repair or servicing should only be

performed by qualified personnel. To maintain the best

accuracy, calibrate Meter once per year.

Cleaning

Periodically wipe the case with a dry cloth and

detergent do not use abrasives or solvents.

Storage

Remove the batteries if the Meter is not used for an

extended period of time, or if stored in temperatures

above 50 °C. If the batteries are not removed, battery

leakage can damage the Meter.

EN

sFLEX 18A

11

General Specifications

LCD display digits :

9,999 digit large scale LCD readout

Overload display : OL or -OL

Battery Type :

2 Batteries, IEC LR6, NEDA 15A, Alkaline (AA)

Battery Life : Alkaline 60 hours

Low Battery Voltage : 2.5V ± 0.2V

Auto Power Off :

The Meter automatically turns off if the buttons are

not pressed for 20 minutes.

Conductor Size : 18 inch

Environmental Conditions

Temperature Coefficient :

0.1 x (specified accuracy) / °C (<18 °C or >28 °C)

Operating Temperature :

-10°C to 30 °C (≤ 80% R.H.)

30°C to 40 °C (≤ 75% R.H.)

40°C to 50 °C (≤ 45% R.H.)

Storage Temperature :

-20°C to 60°C (≤ 80% R.H., no batteries)

Max. Operating Altitude : 2000m (6562 ft.)

Drop Protection :

4 feet drop to hardwood on concrete floor

Vibration :

Random Vibration per MIL-PRF-28800F Class 2

Calibration cycle : One year

Indoor Use

Safety Standards :

• IEC / EN 61010-1

• EN 61010-2-032

• EN 61010-2-033

CAT IV 600V, CAT. III 1000V,

Pollution Degree 2

EN

sFLEX 18A

12

Electromagnetic Compatibility Standards (EMC):

• EN 61326-1

Wireless Communications

• Bluetooth Low Energy (4.0)

• Radio Frequency: 2.4 GHz ISM Band

• Effective Ranges: Open air 10m

Electrical Specifications

Accuracy is given as ± (% of reading + counts of

least significant digit) at 23°C ± 5°C (≤ 80% R.H.)

AC Function

• ACV and ACA specifications are ac coupled, true

RMS.

• For non-sinusoidal waveforms, Additional Accuracy

by Crest Factor (C.F.) :

Add 1.0% for C.F. 1.0 to 2.0

Add 2.5% for C.F. 2.0 to 2.5

Add 4.0% for C.F. 2.5 to 3.0

• Max. Crest Factor of Input Signal:

Frequency Response is specified for sine waveform.

Range Max. Crest Factor Limit

30A

300A

3000A

3.0

2.0

≤ 1500 counts

≤ 2250 counts

1000V

≤ 9999 counts

1.5

3.0

2.0

1.5

≤ 3000 counts

≤ 5000 counts

≤ 7500 counts

EN

sFLEX 18A

13

EN

sFLEX 18A

Range Resolution Accuracy

300A

30A *1 0.01A

0.1A

±(0.3% + 5D)

300A ±(0.3% + 5D)

1A

Position Error of Clamp

Voltage

*1 Minimum Reading is 3.0V

*2 Minimum Reading is +2.4V / -0.7V

AC Frequency Response : 45Hz to 500Hz

Input Impedance : >4kΩ for input voltage up to 30V,

impedance increases to >375kΩ when input voltage up

to 1000V.

Maximum Operation Time :

DT = 30sec for > 30V

Overload Protection: AC / DC 1000V

Model Distance from optimum Accuracy

sFLE

18A

1.4” (35mm) ±1.0%

2.0” (50mm) ±1.5%

2.4” (60mm) ±2.0%

AC Ampere

*1 Minimum Reading is 1.00A

Frequency Response : 45Hz to 500Hz

Overload Protection : 3000A

AC

DC

1000V *1

1000V *2

0.1V

±(1.5%+5D)

±(0.7%+5D)

Function Range Resolution Accuracy

14

AC Frequency

Range Resolution Accuracy

1000Hz

0.1Hz ±(0.3%+3D)

1Hz ±(0.3%+3D)

0.01Hz ±(0.3%+3D)

100Hz *1

10kHz

*1 Minimum Reading is 10Hz

Minimum Sensitivity :

AC A: Reading > 3A at 40Hz to 1kHz, > 6A at

< 40Hz or > 1kHz

AC V: Reading > 10V at 40Hz to 1kHz, > 20V at

< 40Hz or > 1kHz

Resistance / Continuity

Continuity Indicator : Built-in buzzer sounds when

measured resistance is less than 20Ω and sounds off

when measured resistance is more than 200Ω,

between 20Ω to 200Ω the buzzer maybe sound or off

either.

Response Time of Buzzer : < 1ms

Maximum Output Voltage : 2.1V

Overload Protection : AC / DC 1000V

Measuring Rate & Response Time

Range Resolution Accuracy

10kΩ

1Ω ±(0.9%+2D)

0.001kΩ ±(0.9%+2D)

1000Ω

Function Measuring Rate Response Time

A

2 sample(s) per sec 2 sec

1 sample(s) per sec 2 sec

3 sample(s) per sec 2 sec

V / Ω

Hz

EN

sFLEX 18A

15

Limited Warranty

This Meter is warranted to the original purchaser

against defects in material and workmanship for 3

years from the date of purchase. During this warranty

period, manufacturer will, at its option, replace or

repair the defective unit, subject to verification of the

defect or malfunction. This warranty does not cover

disposable batteries, or damage from abuse, neglect,

accident, unauthor-ized repair, alteration, contamina-

tion, or abnormal conditions of operation or handling.

Any implied warranties arising out of the sale of this

product, including but not limited to implied

warran-ties of merchantability and fitness for a

particular purpose, are limited to the above.

The manufacturer shall not be liable for loss of use

of the instrument or other incidental or consequen-tial

damages, expenses, or economic loss, or for any

claim or claims for such damage, expense or

economic loss. Some states or countries laws vary,

so the above limitations or exclusions may not apply

to you.

EN

sFLEX 18A

16

󱅞󸺥󰳅󹋂

!

!󲍨󱆔󲯫󷺴󷦼

󴇲󲵭󳴆󷲃󱖏󶜈󲑷󶤛󰴖󸆲󱁐󲎻󲽞󳾆󰳧󰱰󱓈󹀡󲳰󴆳󱙱󷙧󴢢

󱺞󰵕󷞰󸑳󱞊󳃘󲎌󰱰󱷛󰱰󳖢󲨌󰸴󵂬󷨅󱀕󼶳󱋟󷨅󱀕󳈡󰹡󰱰

󰻋󷳀󲯫󱍶󶜈󱖏󶜈󱕩󸾀

󷭃󰸴󵂬󱖮󸔸󰱰󵫹󲋺󱙱󵲘󱪡󸒡󷙧󴏯󸠉

󴢢󸽺󰷧󴠃󴠥󲽞󷦗󹃆󹎨󹀡󼶳󷭃󱐆󱫈󴬸󴢟󲯫󴃇󹟉󱘾󱪡󲽞󴘫

󴛤󱱚󲾧󰸴󵂬󳠘󵂤󱛂

󰸴󵂬󱋦󷭃󴏯󸠉󲠗󵕴󰱰󹃆󱵪󰵕󹛩󷱝󳷹󴏯󱃙󼴩󰱰󳽝󲡼󸓠

󷙧󱺞󳟘󵅏󲸢󼶳󷭃󸐞󰻥󳷹󴏯󼴩

󷭃󱐆󱫈󱃙󷚒󰰖󵫹󲋺󰱰󸹵󲽞󰵴󰷱󵫹󲋺󶥃󳇚󱫑󰱰󸹵󳖩󱍷

󷿄󸓪󹌰󲎌󰱰󹃆󱵪

󴢢󸕶󱅧󱖏󶜈󲑷󶤛󷦗󹃆󱙱󰴖󱛧󱁐󲎻󰱰󸪮󷫲󷳗󳔨󼶳󷭃󳖦󱉵

󴹰󰷧󹃆󸠉󹍧󵞑󳚈󵪰󱓋󳞭󳈷󹃆󴄣

󸕶󱅧󱠳󰴖󰷽󳯆󰵕󰺙󰴾󰴖󲣇󱎃

󱺞󳷹󴏯󼴩󸓠󰷽󵄠󲡼󲽞󴘫󴛤󼶳󷭃󱐆󰸴󵂬󳷹󴏯󼴩

󱺞󱃙󼴩󱖏󶜈󳇚󷦗󳻻󴏯󸠉󷝬󶏍󰱰󱓈󹀡󲡸󹃆󸘩󰵮󼶳󱋟󲭓󹋅

󰸴󵂬󴶑󵪰󵌴󰻋󷳀󷝬󶏍

󰸴󵂬󴏯󷩳󶄙󲽞󳇔󸠢󳚈󼶳󷭃󲑫󲿇󳃘󳓓󱫈󲿇󳃘󸽖󷳀󷝬󶏍󲫴

󷭃󴇲󲵭󰸴󵂬󹟗󳖦󽶵󽶲󽶶󽶴󲘊󰽭󲽞󽶸󽶲

󰱰󹃆󱵪󰰖󸏯󹃆󱵪󱖏󶜈󸑳󲽘󷦗󹃆

󲿓󸹨󹃆󴄣󶽏󲽞󱃙󷚒󱷛󴀐󰱰󱋦󼶳󷭃󲬎󱃙󷚒󰰖󱕨󰰗󷚒󵮜

󷭃󱐆󱫈󱆒󸘩󵌬󶩉󶀀󶄬󲓼󱷛󹄾󳚈󰸴󵂬󷚒󵮜

󷭃󱐆󰸴󵂬󷿄󸓪󳟅󱷼󹌰󲎌󰽭󰱰󴏯󷩳󶄙󴾬󱳠󹃆󱵪

󱙱󹃆󴉳󵮢󷺴󷦼󵌷󲠗󳖦󳇔󸠢󱙱󳇔󸠢󵫹󸘩󰻋󷳀󽨬󰰖󳴆󳘻

󷭃󱐆󱫈󱙱󴾬󱳠󰱉󰸴󵂬󴅰󳟘󳇔󸠢󰻋󷳀󽨬

󰱰󴏯󷩳󶄙

󵂬󳖦󴏯󸠉󰱰󳇔󸠢󵿟󰵮󲻖󵭟󱖮󽶸󽶳󽶲󽶳󽶲󽶲󽶵󽶳

󰱉󸔸󵂬󳖦󴏯󸠉󼳴󱊰󲽞󰱰󳴆󷨞󼶳󰰧󱆮󹌰󲎌󹃆󱵪󶤙

󲑾󲻖󵮢󳖦󲫩󴏯󹃆󸁠󵌴󹃆󱵪

󱫈󴏯󷩳󹃆󸽣󲑷󸑡󰳆󳯗󵱚󲽞󹃆󲏌󱋦󼶳󷭃󳖞󸹨󹃆󴒐󰰿󳓓

󹃆󲾧󳟘󹟗󱵪󹃆󲏌󼴩

󱺞󸈃󶄙󶀀󶄬󲓼󰱰󱆒󸘩󸥚󶄙󱷛󹄾󼶳󷭃󱐆󰸴󵂬󸈃󲯫󹃆󴉳󱁊

󲶋󼴩

󴇲󲵭

!

󷭃󸕘󲬢󰵕󰰗󷬁󳘻󰵕󵚮󰻋󱃙󼴩󰱰󲍨󱆔󳏪󰷽󶥃󶂶󰻥

󰰙󸕘󲍦󳠘󲿇󱇉󰱰󴇲󲵭󰳅󹋂󱖏󶜈󲑷󶤛󱨇󸠇󱁐󲎻󲽞󳾆󰳧

TC

sFLEX 18A

17

󱫈󲍨󷝬󱙱󳁸󱓓󸈃󲯫󹃆󴉳󳇔󸠢󳠀󸹵󼶳󷭃󲑫󷜉󴏯󷝬󶏍󳖞󹃆

󰰧󵧫󲾏󱖮󸔸󰱰󸽖󷳀󷚋󴯼

󷭃󱐆󲻖󳖦󲽞󵣱󸾞󳖦󳠕󶀀󶄬󵌴󱓈󹀡󲡸󹃆󲑷󹟉󱘾󱪡󼶳󳽞󱖏

󶜈󲑷󶤛󷦗󹃆󹃆󴠣󱁐󲽞󹃆󲨼󸹠󱅟

󱃙󼴩󱙱󳠘󲿇󱇉󰱉󰸴󵂬󰱰󳴆󷫀

!

󱕊󷣥󰸴󵂬󲿇󱇉

󷲝󱘕󽶬󱓈󹀡󹃆󱵪󷦗󹃆󹎨󹀡

󷲝󱘕

󷭃󱐆󰸴󵂬󲽞󵣱󸾞󳖦󱓈󹀡󲡸󹃆󲑷󹟉󰰖

󰳭󴉳󹃆󴉳󲽞󹃆󱵪

󵏣󴉳󹃆󴉳󲽞󹃆󱵪

󶥃

CAT IV

CAT III

󸓪󱵪󼳴󱊰

󷨅󱀕󳘀󱫈󸽖󳽜󱩿󲎌󷨅󱀕󲍨󷝬󰱉󰱰

󷨅󱀕󵌫󵂠󵔉󷳮󼶳󱺞󸛦󹃆󵏇󹔧󶄙󱙱󵖀󸁠

󱊈󳒻󹃆󸁠󰵕󱕗󱷼󱭕󲧨󵲤󴯼󰱰󴧩󳘻󵽎󶀶

󷨅󱀕󳘀󱫈󸽖󳽜󰹀󶤆󰱛󹃆󴒐󵾎󱊰󰱰

󵔉󷳮󼶳󱺞󹃆󸪽󲽞󳣡󵧞󲽞󱫑󰰗󲻖󵂬

󳇚󱫑

󱕩󹂂󲓼󲽞󱍷󲩜󶀀󶄬󰻋󷳀󰱰󷨅󱀕

󹃆󴄣󲏌󸠉

󴥝󶄙󸑿󶄙

󵭟󱖮󳼷󵎿󴒘󱋟

󷭃󱐆󰵴󲵭󰰷󳪑󳠘󵂤󱛂

～

󷲝󱘕

󷲝󱘕󷚒󵞑󱖏󶜈󳊈󱶂󱃙󼴩󷜉󴏯󷨅󱀕󲽞󲑷󶤛󷺴󳕣󴃨󰱧󲯫󸕨

󱸋󰱰󳩊󰵮󱙱󳏪󰷽

󱺞󱃙󼴩󲑫󸹐󳚈󸹵󷌊󳖦󲫩󵂬󴱼󲷞󼶳󲽞󲑫󲌈󳓓󳖦󽶷󽶲󰵕󰰖

󰱰󴒿󲤳󼶳󷭃󱕨󱉵󹃆󴄣󱺞󳠕󱕨󱉵󹃆󴄣󼶳󹃆󴄣󱖏󶜈󴖁󴌕󳊈

󱶂󱃙󷚒

󷭃󱐆󲑫󱃙󼴩󳜾󹄾󳖦󳯗󵫹󴒿󲤳󲽞󹟗󴛤󲤳󴾬󱳠

!

TC

sFLEX 18A

18

󱃙󼴩󳯯󸏯

󽶳󸤄󸭹󳶂󱋇

󽶴󹍧󵞑

󽶵󱍶󶜈󸬸

󽶶󸊘󱆎󵫹󲋺

󽶷󸊘󱆎󵫹󲋺

TC

sFLEX 18A

19

ページが読み込まれています...

APPA sFLEX 18A ユーザーマニュアル

APPA sFLEX 18A ユーザーマニュアル

関連論文

その他のドキュメント