Hitachi CJ 110MV ユーザーマニュアル

English

Jig Saw

CJ 90VST

English

Handling instructions

Keep for future reference

2

3

4

5

6

I

II

III

I

II

7

III

8

I

9

10

11

II

I

12

13

2

1

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

32

31

33

34

35

36 37

38

39

40

41

43

42

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

62

60

61

63

64

65

66

67

69

68

501

502

14

15

English

16

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence

of ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce risk of electric shock.

CONTENTS

GENERAL POWER TOOL SAFETY WARNINGS ........................................16

PRECAUTIONS ON USING JIG SAW ..........................................................18

SYMBOL .......................................................................................................19

SPECIFICATIONS ........................................................................................ 19

STANDARD ACCESSORIES .......................................................................19

OPTIONAL ACCESSORIES (sold separately)..............................................19

APPLICATIONS ............................................................................................20

PRIOR TO OPERATION ...............................................................................20

CUTTING ......................................................................................................22

CONNECTING WITH CLEANER .................................................................. 24

CONCERNING CUTTING OF STAINLESS STEEL PLATES .......................24

SELECTION OF BLADES ............................................................................ 25

HOUSING THE HEXAGONAL BAR WRENCH ............................................25

MAINTENANCE AND INSPECTION ............................................................25

SERVICE PARTS LIST .................................................................................28

English

17

b) Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool.

Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool.

Do not use a power tool while you are tired or under the inﬂ uence of drugs,

alcohol or medication.

A moment of inattention while operating power tools may result in serious personal

injury.

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the oﬀ position before

connecting to power source and/or battery pack, picking up or carrying the

tool.

Carrying power tools with your ﬁ nger on the switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

English

18

b) Do not use the power tool if the switch does not turn it on and oﬀ .

Any power tool that cannot be controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may aﬀ ect the power toolʼs

operation.

If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed.

Use of the power tool for operations diﬀ erent from those intended could result in a

hazardous situation.

5) Service

a) Have your power tool serviced by a qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

CAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of children and inﬁ rm persons.

PRECAUTIONS ON USING JIG SAW

1. Hold power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

2. This Jig saw employs a high-power motor. If the machine is used continuously at

low speed, an extra load is applied to the motor which can result in motor seizure.

Always operate the power tool so that the blade is not caught by the material

during operation. Always adjust the blade speed to enable smooth cutting.

English

19

SYMBOL

WARNING

The following show symbols used for the machine. Be sure that you understand their

meaning before use.

Read all safety warnings and all instructions.

SPECIFICATIONS

Voltage

220 V

Power Input 705 W

Max. Cutting Depth Wood 90 mm

Mild Steel 8 mm

No-load speed 850 – 3000 /min

Stroke 20 mm

Min. Cutting Radius 25 mm

Weight (without cord) 2.2 kg

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the accessories listed in the below.

Blades (No. 41)

Refer to Table 1 on page 26 for use of the blades.

1

Hexagon bar wrench

1

OPTIONAL ACCESSORIES (sold separately)

(1) Various types of blades

Refer to Table 1 on page 26 for use of the blades.

(2) Guide

(3) Sub base

(4) Bench stand (Model TR12-B)

(5) Splinter guard

(6) Dust collection adapter

English

20

APPLICATIONS

○

Cutting various lumber and pocket cutting

○

Cutting mild steel plate, aluminum plate, and copper plate

○

Cutting synthetic resins, such as phenol resin and vinyl chloride

○

Cutting thin and soft construction materials

○

Cutting stainless steel plate (with No. 97 blade)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power requirements speciﬁ ed

on the product nameplate.

2. Power switch

To start the tool, squeeze the trigger and release it to stop. If you want to run the tool

continuously, press the lock button so that the trigger can be locked in ON position.

The trigger can be released easily from locked ON position, if you squeeze the trigger

slightly.

Ensure that the power switch is in the OFF position. If the plug is connected to a power

receptacle while the power switch is in the ON position, the power tool will start operating

immediately, which could cause a serious accident.

3. Extension cord

When the work area is removed from the power source, use an extension cord of suﬃ cient

thickness and rated capacity. The extension cord should be kept as short as practicable.

4. Dust produced in operation

The dust produced in normal operation may aﬀ ect the operator’s health. Either of following

way is recommended.

a) Wear a dust mask

b) Use external dust collection equipment

When using the external dust collection

equipment, connect the adapter with the hose

from external dust collection equipment.

5. Changing blades

(1) Open the lever up to the stop. (Fig. 1-I)

(2) Remove ﬁ tted blade.

(3) Insert new blade up to the stop in the blade

holder. (Fig. 1-II)

(4) Close the lever. (Fig. 1-III)

CAUTION

○

Be sure to switch power OFF and disconnect the plug from the receptacle when

changing blades.

○

Do not open the lever when plunger is moving.

III

I

II

Lever

Blade

Blade holder

Fig. 1

ページが読み込まれています...

Hitachi CJ 110MV ユーザーマニュアル

このマニュアルも適しています

Hitachi CJ 110MV ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント