Hitachi PDA-100K Handling Instructions Manual

カテゴリー
パワーツール
タイプ
Handling Instructions Manual
Disc Grinder
PDA-100K
Handling instructions
Keep for future reference
English
2
3
4
5
6
7
8
9
10
° °
° °
11
12
13
14
501
2
1
3
4
5
6
7
8
9
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
15
1 949-242 4 M5×22
2 949-454 1 M5
3 301-944 1
4 316-484 1 “3, 18”
5 301-941 1 M7
6 317-820 1
7 628-VVC 1
628VVC2PS2-L
8 316-480 1
9 360-567E 1 220V-240V
10 319-898 1
11 320-677 2 D4×70
12 1 340-514E 1 220V-230V
12 2 340-514G 1
220V-230V
“CHN”
13 313-775 1
14 626-VVM 1 626VVC2PS2L
15 309-929 1
16 316-487 1
17 316-486 1
18 301-943 1
19 317-821 1
20 997-263 2 M4×10
21 316-490 1
22 620-1VV 1
6201VVCMPS2L
23 301-946 1
24 316-489 1
25 307-127 4 M4×12
26 302-047 1
27 316-485 1
28 301-945 1
29 308-386 2 M5×16
30 301-949 1
31 301-948 1 “29, 30”
32 320-497 1
33 316-820 1
100MM×4T
A36Q
34 314-437 1
35 317-819 1 “16, 19”
36
–––––––
1
37 320-675 1 “15”
38
–––––––
1
39
–––––––
1
40 302-086 1 D4×20
41 306-664 1 D4×40
42 936-551 2
43 999-021 2
44 313-777 2
45 314-354 1
46 980-063 1
47 938-307 1
48 959-140 1
49 994-273 1
50
–––––––
1
51 304-035 1 D4×25
52 305-499 2 M3.5×6
53 955-509 1
54 980-063 1
55 953-327 1
56 937-631 1
57 984-450 2 D4×16
58
–––––––
1
501 313-933 1
English
16
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, re and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
CONTENTS
GENERAL POWER TOOL SAFETY WARNINGS ........................................16
SAFETY WARNINGS COMMON FOR GRINDING, SANDING OR
CUTTING-OFF OPERATIONS .....................................................................18
KICKBACK AND RELATED WARNINGS .....................................................20
SAFETY WARNINGS SPECIFIC FOR GRINDING AND DIAMOND
WHEEL CUTTING-OFF OPERATIONS ....................................................... 21
ADDITIONAL SAFETY WARNINGS SPECIFIC FOR DIAMOND
WHEEL CUTTING-OFF OPERATIONS ....................................................... 21
SAFETY WARNINGS SPECIFIC FOR SANDING OPERATIONS ................22
PRECAUTIONS ON USING DISC GRINDER ...............................................22
SYMBOLS ....................................................................................................22
SPECIFICATIONS ........................................................................................ 23
STANDARD ACCESSORIES .......................................................................23
OPTIONAL ACCESSORIES (sold separately)..............................................23
APPLICATIONS ............................................................................................24
PRIOR TO OPERATION ...............................................................................24
PRACTICAL GRINDER APPLICATIONS .....................................................25
ASSEMBLING AND DISASSEMBLING THE DEPRESSED CENTER
WHEEL .........................................................................................................26
HOW TO INSTALL THE OPTIONAL ACCESSORIES ..................................26
MAINTENANCE AND INSPECTION ............................................................28
SERVICE PARTS LIST .................................................................................30
English
17
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodi ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool.
Do not use a power tool while you are tired or under the in uence of drugs,
alcohol or medication.
A moment of inattention while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the o position before
connecting to power source and/or battery pack, picking up or carrying the
tool.
Carrying power tools with your nger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
English
18
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and o .
Any power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may a ect the power toolʼs
operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations di erent from those intended could result in a
hazardous situation.
5) Service
a) Have your power tool serviced by a quali ed repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
CAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach of children and in rm persons.
SAFETY WARNINGS COMMON FOR GRINDING,
SANDING OR CUTTING-OFF OPERATIONS
a) This power tool is intended to function as a grind er, sander or cut-o tool. Read
all safety warnings, instructions, illustrations and speci cations pro vid ed with this
power tool.
Failure to follow all instructions listed below may result in electric shock, re and/or serious
injury.
English
19
b) Operations such as polishing, wire brushing or abrasive cutting-o are not
recommended to be performed with this power tool.
Operations for which the power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not speci cally designed and recommended by
the tool man u fac tur er.
Just because the accessory can be attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at least equal to the maximum speed
marked on the power tool.
Accessories running faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or controlled.
f) The arbour size of wheels, anges, backing pads or any other accessory must
properly t the spindle of the power tool.
Accessories with arbour holes that do not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the accessory such
as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess
wear, wire brush for loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystanders away from the plane of
the rotating accessory and run the power tool at maximum no-load speed for one
minute.
Damaged accessories will normally break apart during this test time.
h) Wear personal protective equipment. Depending on application, use face shield,
safety goggles or safety glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping small abrasive or
workpiece fragments.
The eye protection must be capable of stopping ying debris generated by various
operations. The dust mask or respirator must be capable of ltrating particles generated by
your operation. Prolonged exposure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Anyone entering the work
area must wear personal protective equipment.
Fragments of workpiece or of a broken accessory may y away and cause injury beyond
immediate area of operation.
j) Hold power tool by insulated gripping surfaces only, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a”live” wire may make exposed metal parts of the power tool
“live” and shock the operator.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and your hand or arm may be pulled
into the spinning accessory.
English
20
l) Never lay the power tool down until the accessory has come to a complete stop.
The spinning accessory may grab the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Do not operate the power tool near ammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad or any other
accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump toward or away from the operator, depending
on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break
under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as given below.
a) Maintain a rm grip on the power tool and position your body and arm to allow you
to resist kickback forces. Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power tool will move if kickback
occurs.
Kickback will propel the tool in direction opposite to the wheel’s movement at the point of
snagging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and
snagging the accessory.
Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and
cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade.
Such blades create frequent kickback and loss of control.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Hitachi PDA-100K Handling Instructions Manual

カテゴリー
パワーツール
タイプ
Handling Instructions Manual

他の言語で