Hilti SJT 6-A22 取扱説明書

SJT 6-A22

English 1

Eesti 12

Latviešu 23

Lietuvių 35

Русский 47

Українська 60

Қазақ 73

Română 86

Ελληνικά 98

Türkçe 110

日本語 122

한국어 133

繁體中文 143

中文 153

1

2

3

4

5

6

7

8

SJT 6-A22

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

et Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

lt Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 47

uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

ro Manual de utilizare original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

el Πρωτότυπες οδηγίες χρήσης . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

tr Orijinal kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

ja オリジナル取扱説明書 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

ko 오리지널 사용 설명서 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

zh 原始操作說明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

cn 原版操作说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

*2150256*

2150256 English 1

Original operating instructions

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

2 English 2150256

*2150256*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

Stroke rate under no load

Direct current (DC)

The product supports wireless data transmission compatible with iOS and Android platforms.

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed

about the possible hazards. The product described and its ancillary equipment can present hazards if used

incorrectly by untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the type identification plate.

▶ Write down the serial number in the table below. Always quote this information when you contact a Hilti

representative or Hilti Service to inquire about the product.

Product information

Orbital-action jig saw SJT 6-A22

Generation 01

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

*2150256*

2150256 English 3

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶ Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

4 English 2150256

*2150256*

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Safety instructions for reciprocating saws

▶ Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give the operator an electric shock.

▶ Use clamps or another practical way to secure and support the workpiece to a stable platform.

Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.

2.3 Additional safety instructions

Personal safety

▶

Use the power tool only when it is in technically faultless condition.

▶ Never tamper with or modify the tool in any way.

▶ Keep the grips clean and dry.

▶ Suitable protective glasses, ear protection and protective gloves must be worn while the power tool is in

use.

▶ Wear protective gloves when changing the accessory tool. Touching the accessory tool presents a risk

of injury (cuts or burns).

▶ Wear eye protection. Flying fragments present a risk of injury to the body and eyes.

▶ Do not look directly into the light source (LEDs) incorporated in the power tool and do not direct the light

at other persons’ faces. This presents a risk of dazzling or eye damage.

▶ Before beginning the work, check the hazard classification of the dust that will be produced. Use an

industrial vacuum cleaner with an officially approved protection classification in compliance with locally

applicable dust protection regulations.

▶ Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for

the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or

respiratory or other diseases to the operator or bystanders. Certain kinds of dust are classified as

carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing asbestos may be handled only by specialists.

▶ Take breaks between working and do physical exercises to improve the blood circulation in your fingers.

Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous

system in the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the power tool may give you an electric shock if you damage an electric cable

accidentally.

*2150256*

2150256 English 5

Careful handling and use of electric tools

▶ Secure the workpiece. A workpiece clamped in a vice or secured by some other clamping device is more

secure than when held only by hand.

Special safety instructions for jig saws

▶ Always guide the product away from your body when working with it.

▶ Never position your hands ahead of or on the saw blade.

▶ Never cut into unknown materials and keep the line of cut above and below the workpiece free of

obstacles.

▶

Never reach or grip below the workpiece while cutting.

2.4 Battery use and care

▶ Observe the special guidelines applicable to the transport, storage and use of Li-ion batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height

or show signs of damage. In this case, always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. Put the battery in a place where it is clearly visible

and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to

cool down. If it is still too hot to touch after an hour, the battery is faulty. Contact Hilti Service.

3 Description

3.1 Product overview 1

@

On/off switch

;

Grip

=

Stroke rate regulator thumbwheel

%

Battery state of charge indicator

&

Battery release button

(

Battery

)

Air vents

+

Suction adapter

§

Catches

/

Cutting angle adjustment scale

:

Base plate

∙

Orbital-action adjustment lever

$

Saw blade

£

Contact guard

|

Guard

¡

Blade holder

Q

LED light

W

Saw blade release lever

E

Anti-splinter insert

3.2 Intended use

The product described is a hand-held cordless orbital-action jig saw. It is designed to be used for cutting

plastic, wood and metal as well as drywall board and gypsum fiberboard.

The product is equipped with a removable connector for an optional vacuum cleaner / dust removal hose.

This connector is designed to fit standard suction hoses. In order to connect the suction hose to the product,

use of a suitable adapter may be necessary.

6 English 2150256

*2150256*

▶ Use only Hilti Liion batteries of the B 22 series with this product.

▶ Use only Hilti battery chargers of the C4/36 series to charge these batteries.

▶ Use this product only with saw blades equipped with a T-shank.

3.3 Possible misuse

• Use of the product to cut off tree branches or to cut the trunk of a tree is not permissible.

• Use of the product to cut hazardous materials is not permissible.

• Use of the product in a damp or wet environment is not permissible.

3.4 State of charge display

The charge state of the Liion battery is displayed after pressing one of the release buttons lightly (press only

until slight resistance is felt).

Status Meaning

4 LEDs light. Charge state: 75 % to 100 %

3 LEDs light. Charge state: 50 % to 75 %

2 LEDs light. Charge state: 25 % to 50 %

1 LED lights. Charge state: 10 % to 25 %

1 LED blinks. Charge state: < 10 %

Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch. If the battery charge state LEDs blink, please refer to the information

given in the Troubleshooting section.

3.5 Dust blower

The dust blower directs a jet of air toward the saw blade in order to keep the cutting line free of dust.

3.6 Stroke rate

The stroke rate can be adjusted by turning the thumbwheel. Position 1 corresponds to 800 strokes per

minute and position 6 corresponds to 3000 strokes per minute.

3.7 4 orbital-action settings

The 4 orbital-action settings allow cutting performance and quality of cut to be adjusted to suit the material

to be cut. The orbital-action adjustment lever is used to set the power tool to one of the 4 settings.

The lower the orbital-action setting, the finer and cleaner the cut edges will be. The optimum setting can be

determined by carrying out practical tests.

Status Meaning

Position 0 No orbital action

Position 1 Low orbital action

Position 2 Medium orbital action

Position 3 High orbital action

3.8 Anti-splinter insert

The product can be equipped with an anti-splinter insert.

The anti-splinter insert helps prevent splintering on the surface of wood materials when cutting.

3.9 Automatic switch-off

If the on/off switch is pressed continuously for longer than 15 minutes (e.g. during transport or storage), the

tool switches itself off automatically. This prevents deep discharge of the battery.

*2150256*

2150256 English 7

3.10 Items supplied

Orbital-action jig saw with saw blade, guard, dust removal adapter, anti-splinter insert, operating instructions,

hex key.

You can find other system products approved for your product at your local Hilti Center or online at:

www.hilti.com

4 Technical data

4.1 Orbital-action jig saw

SJT 6-A22

Rated voltage

21.6 V

Weight in accordance with EPTA Procedure 01 including B22⁄8.0 battery

3.2 kg

Stroke length

28 mm

Stroke rate under no load (n

0

)

800 /min … 3,000 /min

Maximum cutting performance in wood

150 mm

Maximum cutting performance in aluminium

25 mm

Maximum cutting performance in unalloyed steel

10 mm

Cutting angle (left/right)

0° … 45°

Suction adapter outside diameter

27.5 mm

Storage temperature

−20 ℃ … 70 ℃

Ambient temperature for operation

−17 ℃ … 60 ℃

Battery charging starting temperature

−10 ℃ … 45 ℃

Storage temperature

−20 ℃ … 40 ℃

Ambient temperature for operation

−17 ℃ … 60 ℃

4.2 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the total

working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise emission values

SJT 6-A22

Sound power level (L

WA

)

100 dB(A)

Uncertainty for the sound power level (K

WA

)

5 dB(A)

Sound pressure level (L

pA

)

89 dB(A)

Uncertainty for the sound pressure level (K

pA

)

5 dB(A)

Total vibration

SJT 6-A22

Vibration emission value for sawing wood sheets (a

h,B

)

5.0 m/s²

Uncertainty sawing chipboard (K)

1.5 m/s²

Vibration emission value for sawing sheet metal (a

h,M

)

7.9 m/s²

Uncertainty sawing sheet metal (K)

1.5 m/s²

8 English 2150256

*2150256*

5 Battery

Battery operating voltage

21.6 V

Ambient temperature for operation

−17 ℃ … 60 ℃

Storage temperature

−20 ℃ … 40 ℃

Battery charging starting temperature

−10 ℃ … 45 ℃

6 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery.

6.2 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible click.

3. Check that the battery is seated securely.

6.3 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the tool.

6.4 Fitting the saw blade 2

1. Remove the battery.

2. Push the saw blade (teeth facing the cutting direction) into the blade holder until it engages.

3. Grip and pull the saw blade to check that it is held securely.

6.5 Fitting the guard 3

1. Remove the battery.

2. Push the guard onto the power tool from the front until it clicks into place.

The guard can be fitted only when the base plate is in the normal position (zero degrees position).

6.6 Fitting the dust removal adapter 4

1. Push the dust removal adapter on to the base plate horizontally from the rear until both catches engage

at the side.

2. Connect the vacuum cleaner hose to the dust removal adapter.

*2150256*

2150256 English 9

7 Operation

Observe the safety instructions and warnings in this documentation and on the product.

7.1 Using a dust extractor

The dust extractor reduces dust emissions, increases working safety by providing better visibility of

the cutting line and reduces exposure to dust and wood chips at the workplace.

1. Fit the guard. → page 8

2. Always use a dust extractor when working over a lengthy period with wood or materials that can cause

high dust concentrations.

7.2 Switching on 5

1. Insert the battery.

A safety interlock ensures that the tool doesn’t start when the tool is first switched on and the

battery then fitted, i.e. slid into place on the tool.

Pull the on/off switch back and then slide it forward again.

2. To switch the tool on, slide the on/off switch forward.

7.3 Plunge cutting

1. Set the orbital-action adjusting lever to position 0.

2. Bring the front edge of the base plate into contact with the workpiece.

3. Hold the product securely and press the on/off switch.

4. Press the product firmly against the workpiece and begin the plunge cut by slowly reducing the angle of

attack.

5. Once the blade has penetrated right through the workpiece, bring the product into its normal working

position.

▶ The base plate then lies flat on the working surface.

6. Continue to saw along the cutting line.

7.4 Switching off

▶ To switch the tool off, slide the on/off switch back.

8 Removal

8.1 Removing the suction adapter 6

1. Press the two retaining catches inwards.

2. Pull the suction adapter away from the base plate toward the rear.

3. Pull the vacuum cleaner hose off the suction adapter.

8.2 Removing the guard 7

1. Remove the battery.

2. Tilt the guard slightly and pull it off toward the front.

8.3 Ejecting the saw blade 8

WARNING

Risk of injury. Uncontrolled ejection of the saw blade can lead to injury.

▶

When ejecting the saw blade, hold the product in such a way that it presents no risk of injury to persons

or animals.

1. Remove the battery.

2. Push the saw blade release lever to the side, as far as it will go.

▶ The saw blade will be released and ejected.

10 English 2150256

*2150256*

9 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

9.1 Cleaning the suction adapter

1. Remove the battery.

2. Remove the suction adapter. → page 9

3. Clean the suction adapter.

4. Check that the catches are undamaged.

5. Fit the dust removal adapter. → page 8

9.2 Cleaning the saw blade

1. Clean resin deposits from used saw blades at regular intervals.

2. Place the saw blades in a bath of kerosene (paraffin oil) or commercially-available resin remover for 24

hours.

10 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶

Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a window pane.

*2150256*

2150256 English 11

▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized

persons.

▶ Check the tool and batteries for damage before use after long periods of storage.

11 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

Trouble or fault Possible cause Action to be taken

The saw blade drops out. The saw blade is not correctly en-

gaged.

▶ Repeat the insertion procedure.

▶ Make sure that the blade holder

is fully open and that the saw

blade is pushed all the way in

against the spring resistance.

The clamping system is clogged

with foreign matter.

▶ Clean out the blade holder.

The saw blade cannot be

inserted.

The clamping system is clogged

with foreign matter.

▶ Clean out the blade holder.

The orbital action cannot be

adjusted.

Foreign matter in the orbital-action

adjusting lever groove.

▶ Clean out the orbital-action

adjusting lever groove.

The orbital action doesn’t

work.

The orbital-action mechanism is

clogged with foreign matter.

▶ Check whether foreign matter

is present in the area of the

orbital-action fork and clean it

out.

The orbital-action adjusting lever is

in position “0”.

▶ Adjust it to the desired setting.

The battery runs down more

quickly than usual.

Very low ambient temperature. ▶ Allow the battery to warm up

slowly to room temperature.

The battery doesn’t engage

with an audible click.

The retaining lugs on the battery

are dirty.

▶ Clean the retaining lugs and refit

the battery.

1 LED blinks.

The power tool doesn’t run.

Low battery. ▶ Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶ Allow the battery to cool down

or warm up slowly to room

temperature.

All 4 LEDs blink.

The power tool doesn’t run.

The tool has been overloaded. ▶ Release the on/off switch and

then press it again. Then allow

the power tool to run under no

load for approx. 30 seconds.

The power tool or battery

gets very hot.

Electrical fault. ▶ Switch the power tool off im-

mediately, remove the battery,

keep it under observation, allow

it to cool down and contact Hilti

Service.

12 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

Battery disposal

Improper disposal of batteries can result in health hazards from leaking gases or fluids.

▶ DO NOT send batteries through the mail!

▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶ Dispose of your battery out of the reach of children.

12 Eesti 2150256

*2150256*

▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

▶ Do not dispose of power tools, electronic equipment or batteries as household waste!

13 RoHS (Restriction of Hazardous Substances)

Click on the links to go to the table of hazardous substances: qr.hilti.com/r5212958

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

14 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about the warranty conditions.

Originaalkasutusjuhend

1 Andmed dokumentatsiooni kohta

1.1 Kasutusjuhend

• Enne seadme kasutuselevõttu lugege see kasutusjuhend läbi. See on ohutu kasutamise ja tõrgeteta töö

eeldus.

• Järgige kasutusjuhendis esitatud ja tootele märgitud ohutusnõudeid ja hoiatusi.

• Hoidke kasutusjuhend alati seadme juures ja toote edasiandmisel teistele isikutele andke üle ka

kasutusjuhend.

1.2 Märkide selgitus

1.2.1 Hoiatused

Hoiatused annavad märku toote kasutamisel tekkivatest ohtudest. Kasutatakse alljärgnevaid märksõnu:

OHT

OHT !

▶ Võimalikud ohtlikud olukorrad, mis võivad põhjustada kasutaja raskeid kehavigastusi või hukkumist.

HOIATUS

HOIATUS !

▶ Võimalik ohtlik olukord, mis võib põhjustada kasutaja raskeid kehavigastusi või hukkumist.

ETTEVAATUST

ETTEVAATUST !

▶ Võimalikud ohtlikud olukorrad, mis võivad põhjustada kehavigastusi või varalist kahju.

1.2.2 Kasutusjuhendis kasutatud sümbolid

Selles dokumendis kasutatakse järgmisi sümboleid.

Lugege enne kasutamist läbi kasutusjuhend!

Soovitused seadme kasutamiseks ja muu kasulik teave

Taaskasutatavate materjalide käsitsemine

Elektriseadmeid ja akusid ei tohi visata olmejäätmete hulka.

*2150256*

2150256 Eesti 13

1.2.3 Joonistel kasutatud sümbolid

Joonistel kasutatakse järgmisi sümboleid.

Numbrid viitavad vastavatele joonistele kasutusjuhendi alguses

Numeratsioon kajastab tööetappide järjekorda pildi kujul ja võib tekstis kirjeldatud tööetappidest

erineda

Positsiooninumbreid kasutatakse ülevaatejoonisel ja need viitavad selgituste numbritele toote

ülevaates

See märk näitab, et toote käsitsemisel tuleb olla eriti tähelepanelik.

1.3 Tootepõhised sümbolid

1.3.1 Sümbolid tootel

Tootel võidakse kasutada järgmisi sümboleid:

Tühikäigusagedus

Alalisvool

Seade toetab andmete traadita ülekandmist, mis on ühildatav iOS- ja Android-platvormidega.

Li-ioonaku

Kasutatud Hilti Li-Ion-aku seeria. Pidage kinni peatükis Nõuetekohane kasutamine esitatud

juhistest.

Ärge kasutage akut kunagi löögiriistana.

Ärge laske akul kunagi maha kukkuda. Ärge kasutage akut, mis on saanud löögi või on muul moel

kahjustatud.

1.4 Tooteinfo

tooted on ette nähtud professionaalsele kasutajale ja neid tohivad käsitseda, hooldada ja korras

hoida ainult volitatud ja asjaomase väljaõppega isikud. Nimetatud personal peab olema teadlik kõikidest

võimalikest ohtudest. Seade ja sellega ühendatavad abitööriistad võivad osutuda ohtlikuks, kui neid ei

kasutata nõuetekohaselt või kui nendega töötab asjaomase väljaõppeta isik.

Tüübitähis ja seerianumber on tüübisildil.

▶ Kandke seerianumber järgmisse tabelisse. Tehke need andmed teatavaks alati, kui pöördute päringutega

meie esindusse või hooldekeskusse.

Tooteinfo

Pendeltikksaag SJT 6-A22

Põlvkond 01

Seerianumber

1.5 Vastavusdeklaratsioon

Kinnitame ainuvastutajana, et käesolevas kasutusjuhendis kirjeldatud seade vastab kehtivate direktiivide ja

standardite nõuetele: Vastavusdeklaratsiooni koopia leiate käesoleva kasutusjuhendi lõpust.

Tehnilised dokumendid on saadaval:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

14 Eesti 2150256

*2150256*

2 Ohutus

2.1 Üldised ohutusnõuded elektriliste tööriistade kasutamisel

HOIATUS! Lugege kõiki selle elektrilise tööriista juurde kuuluvaid ohutusjuhiseid, nõuandeid,

jooniseid ja tehnilisi andmeid! Järgmiste juhiste eiramise tagajärg võib olla elektrilöök, tulekahju ja/või

rasked vigastused.

Hoidke kõik ohutusnõuded ja juhised edaspidiseks kasutamiseks alles.

Ohutusjuhistes kasutatud mõiste "elektriline tööriist" käib võrgutoitega (toitejuhtmega) elektriliste tööriistade

või akutoitega (toitejuhtmeta) elektriliste tööriistade kohta.

Ohutus töökohal

▶ Hoidke oma töökoht puhas ja valgustage seda korralikult. Korrastamata ja valgustamata töökoht

võib põhjustada õnnetusi.

▶

Ärge kasutage elektrilist tööriista plahvatusohtlikus keskkonnas, kus leidub tuleohtlikke vedelikke,

gaase või tolmu. Elektrilistest tööriistadest lööb sädemeid, mis võivad tolmu või aurud süüdata.

▶ Hoidke lapsed ja kõik teised töökohast eemal, kui kasutate elektrilist tööriista! Kui teie tähelepanu

juhitakse kõrvale, võib seade teie kontrolli alt väljuda.

Elektriohutus

▶ Elektrilise tööriista pistik peab sobima pistikupessa. Pistiku juures ei tohi teha mingeid muudatusi.

Kaitsemaandusega seadmete puhul ei tohi kasutada adapterpistikuid. Muutmata pistikud ja sobivad

pistikupesad vähendavad elektrilöögiohtu.

▶ Vältige keha kontakti maandatud pindadega (nt toru, radiaator, pliit, külmik). Kui teie keha on

maandatud, on elektrilöögi oht suurem.

▶ Kaitske elektrilist tööriista vihma ja niiskuse eest. Kui elektrilise tööriista sisemusse satub vett,

suurendab see elektrilöögiohtu.

▶

Ärge kasutage ühenduskaablit elektrilise tööriista kandmiseks, riputamiseks ega pistiku stepslist

väljatõmbamiseks! Hoidke ühenduskaablit eemal kuumusest, õlidest, teravatest servadest ja

liikuvatest osadest. Kahjustatud või keerdus ühenduskaablid suurendavad elektrilöögiohtu.

▶ Kui töötate elektrilise tööriistaga vabas õhus, kasutage ainult selliseid pikendusjuhtmeid, mida

tohib kasutada ka välitingimustes. Välitingimustesse sobiva pikendusjuhtme kasutamine vähendab

elektrilöögiohtu.

▶ Kui seadmega töötamine niiskes keskkonnas on vältimatu, kasutage rikkevoolu kaitselülitit.

Rikkevoolu kaitselüliti kasutamine vähendab elektrilöögiohtu.

Inimeste ohutus

▶

Olge tähelepanelik, jälgige, mida teete, ja toimige elektrilise tööriistaga töötades kaalutletult. Ärge

töötage elektrilise tööriistaga, kui olete väsinud või alkoholi, narkootikumide või ravimite mõju all!

Hetkeline tähelepanematus elektrilise tööriista kasutamisel võib põhjustada raskeid kehavigastusi

ja varalist kahju.

▶ Kandke isiklikke kaitsevahendeid ja alati kaitseprille. Isiklike kaitsevahendite, nt tolmumaski,

libisemiskindlate turvajalatsite, kaitsekiivri või kuulmiskaitsevahendite kandmine (sõltuvalt elektrilise

tööriista tüübist ja kasutusalast) vähendab vigastusohtu.

▶ Vältige elektrilise tööriista soovimatut käivitamist! Enne elektrilise tööriista ühendamist vooluvõrku

ja/või elektrilise tööriista aku paigaldamist, tööriista ülestõstmist ja kandmist veenduge, et

elektriline tööriist on välja lülitatud! Kui hoiate elektrilise tööriista kandmisel sõrme lülitil või ühendate

vooluvõrku sisselülitatud tööriista, võib juhtuda õnnetus.

▶ Enne elektrilise tööriista sisselülitamist eemaldage selle küljest seade- ja mutrivõtmed. Elektrilise

tööriista pöörleva osa küljes olev seade- või mutrivõti võib põhjustada vigastusi.

▶ Vältige ebatavalist tööasendit! Võtke stabiilne tööasend ja säilitage alati tasakaal. Nii saate elektrilist

tööriista ootamatutes olukordades paremini kontrollida.

▶

Kandke sobivat rõivastust. Ärge kandke laiu riideid ega ehteid! Hoidke juuksed, rõivad ja kindad

seadme liikuvatest osadest eemal. Lotendavad riided, ehted ja pikad juuksed võivad sattuda seadme

liikuvate osade vahele.

▶ Kui elektrilise tööriista külge on võimalik paigaldada tolmueemaldus- ja kogumisseadiseid, veen-

duge, et need on tööriistaga ühendatud ja et neid kasutatakse nõuetekohaselt. Tolmueemaldus-

seadise kasutamine võib vähendada tolmust tingitud ohte.

▶

Ärge laske tekkida petlikul turvatundel ega eirake elektrilise tööriista ohutusreegleid isegi siis, kui

olete pärast paljukordset kasutamist elektrilise tööriistaga harjunud. Tähelepanematu käsitsemine

võib sekundi murdosa jooksul kaasa tuua raskeid vigastusi.

ページを読み込んでいます...

Hilti SJT 6-A22 取扱説明書

関連論文