E1
CP-UM-5986JEC
Smart Loader Package
Model SLP-C1F
Installation Manual
Thank you for purchasing this product. This manual contains
information for ensuring the safe and correct use of the
product. Those designing or maintaining equipment that uses
this product should first read and understand this manual. Be
sure to keep it nearby for handy reference.
Please read the “Terms and Conditions” from the following
URL before ordering or use:
https://www.azbil.com/products/factory/order.html
NOTICE
Please make sure that this manual is available to the user of
the product.
Unauthorized duplication of this user’s manual in part or in
whole is forbidden. The information and specifications in this
manual are subject to change without notice.
Considerable effort has been made to ensure that this manual
is complete and accurate, but if you should find an omission
or error, please contact us.
In no event is Azbil Corporation liable to anyone for any
indirect, special, or consequential damages as a result of
using this product.
UNPACKING
The following items should be included in your purchase.
• CD-ROM (1)
• Installation manual (this document) CP-UM-5986E
• Software License Agreement CP-UM-5985JE (1)
• USB loader cable*1 81441177-001 (1)
• USB loader cable (A-microB)*2 SLP-ULCJA0 (1)
*1 Included with SLP-C1FJA0 and SLP-C1FJA2.
*2 Included with SLP-C1FJA2 and SLP-C1FJA3.
OVERVIEW
Smart loader package model SLP-C1F is a tool for configuring and
monitoring a model C1A or C1M single loop controller.
Install this product on a computer and connect it to the C1M with
the 81441177-001 loader cable or to the C1A with the SLP-ULCJA0
loader cable.
OPERATING ENVIRONMENT
Hardware CPU Windows PC with an Intel CPU
Recommended: 1.5 GHz or more
Minimum: 1 GHz
Operating system Windows 10
Memory (RAM) Recommended: 4 GB or more
Minimum: 2 GB
Hard disk drive Recommended free space: 20 GB or more
Minimum: 10 GB
Monitor resolution 1366 × 768 or higher
USB ports 1 or more
(One is necessary to connect to the C1M
with USB loader cable 81441177-001)
Optical drive Used to install the software from the
CD-ROM.
Input devices Keyboard, mouse, touchpad, etc.
Other
devices
PDF viewer Adobe Acrobat DC or later version
INSTALLATION
(1) Execute setup_v2_0_0.msi.
(Numbers indicate the version of SLP-C1F.)
(2) Follow the displayed messages to install.
After you have agreed to the license agreement and selected
the destination folder, the actual installation will begin.
(3) When the message below is displayed, installation is complete.
Click the [Finish] button to exit the installer.
INSTALLING THE USB LOADER CABLE DEVICE DRIVER
To configure and monitor the C1M with the included 81441177-001
USB loader cable, driver installation is required. Install the driver
using the procedure below.
Driver installation is not required in the case of the C1A with the
SLP-ULCJA0 loader cable.
If you are using the USB loader cable on your computer for the first
time, proceed with driver installation.
If you have an outdated driver for the USB loader cable installed on
your computer, uninstall the outdated driver first.
How to check the version of the USB loader cable
The version is shown on the sticker attached to the USB loader cable.
REV.05 to 06 Driver installation is required.
If an old driver is installed, uninstall it first.
No “REV” number Not supported
Use Rev. 05 or a higher version of the USB
loader cable.
Checking the driver
(1) Plug the USB loader cable into a USB port.
(2) Open the Device Manager.
Right-click the [Start] button and click [Device Manager] to
open it.
(3) Check the version.
In the Device Manager, in “Ports (COM & LPT),” open
the properties of the Yamatake USB Loader Comm. port
(COMx) and go to the Driver tab to check the driver version.
Versions 0.x.x.x to 4.x.x.x are old drivers.