Stanley STPT600 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

Stanley STPT600 は、吹き飛ばしと掃除の用途に加え、軽く吸い込む用途にも設計された、600W の可変速度ブロワーです。ノズルを取り付けると、落ち葉、芝生、ごみなどの吹き飛ばしに使用でき、ノズルとダストバッグを取り付けると、ごみ、ほこり、破片などの吸い込みに使用できます。スイッチをロックするボタンがあり、連続使用時に便利です。

Stanley STPT600 は、吹き飛ばしと掃除の用途に加え、軽く吸い込む用途にも設計された、600W の可変速度ブロワーです。ノズルを取り付けると、落ち葉、芝生、ごみなどの吹き飛ばしに使用でき、ノズルとダストバッグを取り付けると、ごみ、ほこり、破片などの吸い込みに使用できます。スイッチをロックするボタンがあり、連続使用時に便利です。

STPT600
3
6
A
B
7
C
D
6
8
5
4
3
2
1
3
ENGLISH
STPT600
600W Variable Speed Blower
SPECIFICATION STPT600
Power W 600
Voltage V 110
TW
Frequency Hz 60
No-Load Speed /min
0-16,000
Air Volume m
3
/min 3.5
Weight Kg 1.6
Technical data
Intended use
Your Stanley Blower has been designed for blowing &
cleaning applications, as well as light suction purpose.
General Power tool Safety Warnings
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
4
ENGLISH
Electrical safety
Labels on tool
Position of Date Barcode
This tool is double insulated; therefore no earth
The following symbols are shown on the tool:
The Date Code (8), which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
Warning! To reduce the risk of injury, the user
must read the instruction manual.
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
Additional Safety Instructions for Blowers
Do not collect still smoldering cigarette ashes, freshly cut
metals shaving, screws, nails and the like.
Never block suction inlet and outlet.
Warning symbols
Do not use in the rain or leave outdoors while it is
raining.
Always wear eye protection.
Always wear ear protection.
Keep bystanders away.
Do not touch the fan.
Do not cross gravel paths or roads whilst your product is
switched on during blow/vac mode. Walk, never run.
Always be sure of your footing, particularly on slopes.
Do not overreach and keep your balance at all times.
Do not place the inlet or outlet of the vacuum near eyes
or ears when operating. Never blow debris in the
direction of bystanders.
Keep all cooling air inlets clear of debris.
To protect your feet and legs while operating the
Never allow children to use the appliance.
Wear protective goggles while operating.
appliance, always wear heavy duty footwear and long
trousers.
If operating an appliance in a damp location is
unavoidable, use a Residual Current Device (RCD) with a
tripping current of not more than 30mA protected supply.
Use of an RCD reduces the risk of electric shock.
Store the appliance only in a dry place.
To prevent dust irritation the wearing of a face mask is
recommened.
Disconnect the appliance from the mains supply
- whenever you leave the machine;
- before cleaning a blockage;
- before checking, cleaning or working on the appliance;
- if the appliance starts to vibrate abnormally.
Switch off: remove plug from mains before
cleaning or maintenance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service
centre in order to avoid a hazard.
The extension cable must be suitable for outdoor use and
marked accordingly. Up to 0.75 mm² H05VV-F or H05RN-F
extension cable can be used without loss of product
performance.
5
ENGLISH
Replacing Carbon Brushes (fig. D)
Use a screwdriver to remove the brush holder cap.
Take out the worn carbon brush, insert the new one and
secure the brush hold cap.
Warning!
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark.
Accessories
The performance of your tool depends on the accessory used.
Stanley and Piranha accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best from
your tool.
Mounting The Nozzle And Dust For DustCollection
(fig. B)
For dust collection, mount the Dust Bag at the Blast Port
(2) and Nozzle at the Suction Port (6)
To remove Dust Bag and Nozzle, simply pull out by first
turning in the opposite direction.
Empty the Dust Bag frequently to ensure maximum dust
collecting efficiency.
Operating The Blower (fig. C)
To switch your Blower on, depress the Switch (3). To stop
your Blower, release Switch.
Adjust Variable Speed Knob (4) for different speed
requirement.
When continuous operation is required, first depress the
switch and then the lock-on button (5) and release to
disengage lock, squeeze and release switch.
Warning: Continuous running of machine should not exceed
30 minutes.
Protecting the environment
Separate collection. This product must not
bedisposed of with normal household waste.
Should you find one day that your Stanley productneeds
replacement, or if it is of no further use to you, do notdispose
of it with household waste. Make this productavailable for
separate collection.
Separate collection of used products and packagin-
gallows materials to be recycled and used
again.Re-use of recycled materials helps preventenvi-
ronmental pollution and reduces the demand forraw
materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplug.
Use
Mounting The Nozzle For Blowing Operations (fig. A)
Insert the pin located inside the Nozzle into the notch
provided on the Blast Port (1)
To lock Nozzle in place, turn the Nozzle in the direction
indicated.
To remove Nozzle, turn the Nozzle in the opposite
direction.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Features
This tool includes the following features:
1. Nozzle
2. Blast Port
3. Trigger Switch
4. Variable Speed Knob
5. Lock-On Button
6. Suction Port
7. Dust Bag
6
Stanley
@ `
/
1.
a.
b.
c.
2.
a.
b.
c.
d.
e.
f.
(RCD) RCD
3.
a.
b.
c. /
d.
e.
f.
g.
4.
a.
STPT600
600W
S
PECIFICATION STPT600
TW
V 110
Hz 60
W 600
/min 0-16,000
m
3
/min 3.5
Kg 1.6
7
b.
c.
/
d.
e.
f.
g.
5.
a.
/
30mA (RCD) RCD
-
-
-
-
(8)
2014 XX JN
STANLEY
0.75 mm
2
H05VV-F H05RN-F
8
1.
2.
3.
4.
5.
6.
7.
A
(1)
B
(2)
(6)
C
(3)
(4)
(5)
30
D
Stanley
Piranha
Stanley
137
02-29994633
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Stanley STPT600 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

Stanley STPT600 は、吹き飛ばしと掃除の用途に加え、軽く吸い込む用途にも設計された、600W の可変速度ブロワーです。ノズルを取り付けると、落ち葉、芝生、ごみなどの吹き飛ばしに使用でき、ノズルとダストバッグを取り付けると、ごみ、ほこり、破片などの吸い込みに使用できます。スイッチをロックするボタンがあり、連続使用時に便利です。

他の言語で