Stanley STHM5KH は、コンクリート、レンガ、石造りの軽度または中程度の破砕、チゼル、解体作業用に設計された、専門的なハンマーです。このツールは、回転運動を打撃運動に変換するピストンメханиズムを使用して動作します。このツールには、作業中に発生する振動を低減するアンチバイブレーションシステムも搭載されています。Stanley STHM5KH は、安全かつ効率的に作業するためのさまざまな機能を備えています。
Stanley STHM5KH は、コンクリート、レンガ、石造りの軽度または中程度の破砕、チゼル、解体作業用に設計された、専門的なハンマーです。このツールは、回転運動を打撃運動に変換するピストンメханиズムを使用して動作します。このツールには、作業中に発生する振動を低減するアンチバイブレーションシステムも搭載されています。Stanley STHM5KH は、安全かつ効率的に作業するためのさまざまな機能を備えています。
STHM5
English 4
简体中文 9
Figure 1
f
a
d
c
e
b
b
a
A
B
d
d
Figure 3 Figure 4
Figure 2
f
g
h
i
2
3
1
4
4
ENGLISH
4
SPECIFICATION
STHM5-A9
Voltage V 220
Frequency Hz 50
Power W 1010
Impact rate
bpm
2900
Impact energy J 8.5
Chisel positions 6
Chuck type mm Hex 17
Weight kg 6.1
Intended use
Your Stanley Demolition Hammer has been designed for
professional light or medium chipping, chiselling and demoli-
tion applications in concrete, brick and masonry.
General Power Tool Safety Warnings
@
WARNING! Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock,
re and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FU-
TURE REFERENCE.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
Demolition Hammer
STHM5
Technical data
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk of
electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
inuence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
ENGLISH
5
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Hammer safety warnings
u Wear ear protectors. Exposure to noise can cause
hearing loss.
u Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting acces-
sory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
u Be certain that the material being drilled does not con-
ceal electric or gas service and that their locations have
been veried with the utility companies.
u Keep a rm grip on the tool at all times. Do not
attempt to operate this tool without holding it with
both hands. Operating this tool with one hand will result
in loss of control. Breaking through or encountering hard
materials such as re-bar may be hazardous as well.
Tighten the side handle securely before use.
u Ensure the chisel is secured in place before operating
the tool.
u In cold-weather conditions or when the tool has not been
used for a longer period of time, let the tool run with no
load for several minutes before use.
u When working above ground level ensure the area below
is clear.
u Do not touch the chisel or the parts close to the chisel
immediately after operation, as they may be extremely
hot and cause burns to the skin.
u Always direct the power cable to the rear, away from the
chisel.
u Do not operate this tool for long periods of time.
Vibration caused by hammer action may be harmful to
your hands and arms. Use gloves to provide extra cush-
ion and limit exposure by taking frequent rest periods.
Other risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. In spite of the
application of the relevant safety regulations and the imple-
mentation of safety devices, certain risks cannot be avoided.
These are:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
ENGLISH
6
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed
when using your tool (example:- working with wood, es-
pecially oak, beech and MDF.)
LABELS ON TOOL
The following symbols are shown on the tool:
:
WARNING! To reduce the risk of injury, the user
must read the instruction manual.
POSITION OF DATE BARCODE
The Date Code, which also includes the year of manufacture,
is printed into the housing.
Example
2014 XX JN
Year of manufacturing
ELECTRICAL SAFETY
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service Centre in
order to avoid a hazard.
Using an Extension Cable
If it is necessary to use an extension cable, please used an
approved extension cable that fits the tool’s power input spec-
ifications (please refer to the technical data). The minimum
cross-sectional area of the conducting wire is 1.5 sq. mm.
Cables should be untangled before reeling up.
FEATURES
This tool includes some or all of the following features.
a. Side Handle
b. Switch
c. Barrel cover
d. Tool sleeve
e. Lube oil-injection inlet
ASSEMBLY AND ADJUSTMENTS
@
WARNING: To reduce the risk of injury,
turn unit off and disconnect machine
from power source before installing and
removing accessories, before adjusting or
changing set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can cause
injury.
INSERTING AND REMOVING HEX 17MM AC-
CESSORIES (g. 1)
This tool uses HEX 17mm accessories (refer to the inset in
gure 1 for a cross-section of an HEX 17mm bit shank). We
recommend to use professional accessories only.
1. Clean and grease the bit shank.
2. Insert the bit shank into the bit holder/tool sleeve (d).
3. Push the bit down and turn it slightly until it ts into the
slots.
4. Pull on the bit to check if it is properly locked. The
hammering function requires the bit to be able to move
axially several centimetres when locked in the tool
holder.
5. To remove a bit pull back the tool holder/locking sleeve
(d) and pull out the bit.
@
WARNING: Always wear gloves when you
change accessories. The exposed metal
parts on the tool and accessory may become
extremly hot during operation.
FITTING THE SIDE HANDLE (g. 1)
The side handle (a) can be tted to suit both RH- and LH-
users.
@
WARNING: Do not use the tool without the side
handle properly assembled.
1. Loosen the side handle.
2. For RH-users: Slide the side handle clamp over the
collar behind the tool holder, handle at the left.
For LH-users: Slide the side handle clamp over the
collar behind the tool holder, handle at the right.
3. Rotate the side handle to the desired position and
tighten the handle.
OPERATION INSTRUCTIONS FOR USE
ENGLISH
7
@
WARNING:
• Always observe the safety instructions and applicable
regulations.
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approx. 5 kg).
Excessive force does not speed up chiselling but
decreases tool performance and may shorten tool life.
• Always hold the tool rmly with both hands and ensure a
secure stance (g. 3). Always operate the tool with the
side handle properly mounted.
PROPER HAND POSITION (g. 3)
@
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
@
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(a), with the other hand on the main handle.
SWITCHING ON AND OFF (g. 1)
1. To run the tool, press the switch(b) and turn it in 'ON'
position.
2. To stop the tool, turn it in 'OFF' position and release the
switch(b).
CHIPPING AND CHISELLING (g. 1)
1. Insert the appropriate chisel in right position.
2. Adjust the side handle (a) as required.
3. Switch on the tool and start working.
4. Always switch off the tool when work is nished and
before unplugging.
WARNING:
u Do not use this tool to mix or pump easily combustible or
explosive uids (benzine, alcohol, etc.).
u Do not mix or stir inammable liquids labelled accord-
ingly.
MAINTENANCE
Your Stanley corded/cordless appliance/tool has been de-
signed to operate over a long period of time with a minimum
of maintenance. To ensure satisfactory operations, the tool
must be maintained and cleaned regularly
WARNING! Before performing any maintenance on corded/
cordless power tools:
uSwitch off and unplug the appliance/tool.
uOr switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
uOr run the battery down completely if it is integral and
then switch off.
uUnplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your appliance/
tool/ charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior (when fitted).
REPLACE THE CARBON BRUSH (g. 4)
A
LUBRICATION
u Regularly replace and check the carbon brushes. Re-
place it in time when it is worn to the abrasive boundary
line. Keep the carbon brush clean and make it freely slide
in the brushing range. Two brushes shall be replaced at
the same time.
uUse the cross screwdriver to counterclockwise unscrew
the screws (4), open the bottom cover(1) with a flat screw-
driver to counterclockwise open the brush cover(2), you
can remove the brush(3)as shown in the figure 4, and
put the new brush, and then clockwise fasten the brush
cover(2), finally put the bottom cover(1), and then use the
cross screwdriver to tighten it properly.
uOpen the cap of the lube oil-injection inlet(e), check the
lube oil in the gearbox, if the lube oil is dirty or insufficient,
replace or add the adequate amount of lube oil provided
by the company.
S
CLEANING
@
WARNING! Blow dirt and dust out of the main hous-
ing with dry air as often as dirt is seen collecting in
and around the air vents. Wear approved eye pro-
tection and approved dust mask when performing
this procedure.
@
WARNING! Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
ENGLISH
8
tool. These chemicals may weaken the material of
the parts. Use only mild soap and damp cloth to
clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into liquid.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your Stanley product needs re-
placement, or if it is of no further use to you, do not dispose
of it with household waste. Make this product available for
separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product
REMARKS
u Stanley's policy is one of continuous improvement to our
products and as such, we reserve the right to modify product
specications without prior notice.
uStandard equipment and accessories may vary by country.
uProduct specications may differ by country.
u Complete product range may not be available in all countries.
Contact your local Stanley dealers for range availability.
简体中文
9
STHM5-A9
V 220
Hz 50
W 1010
bpm
2900
J 8.5
6
mm 17
kg 6.1
1.
a.
b.
c.
2.
STHM5
a.
b.
c.
d.
e.
f.
RCD RCD
3.
a.
b.
c. /
d.
e.
f.
g.
4.
a.
b.
简体中文
10
c.
d.
e.
f.
g.
5.
a.
u
u
u
u
u
u
u
u
u
u
u
u
u/
u
u
u
u
:
2014 XX JN
u
( )
1.5
简体中文
11
a.
b.
c.
d.
e.
@
.
17 ( 1)
17
317
1.
2.
d
3.
4.
5.
d
@
( 1)
a
@
1.
2.
3.
@
•
•
• 5
•
3
( 3)
@
@
a
1
1. (b)
2.
(b)
1
1.
2. a
3.
4.
u
u
/ /
/
简体中文
12
u/
u/
/
u/
u
u/ /
u
u
4
A
u
u (4)
(1)(2)
(3)
(2)(1)
u (e)
S
@
@
u
u
u
u
N405589 201409
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Stanley STHM5KH は、コンクリート、レンガ、石造りの軽度または中程度の破砕、チゼル、解体作業用に設計された、専門的なハンマーです。このツールは、回転運動を打撃運動に変換するピストンメханиズムを使用して動作します。このツールには、作業中に発生する振動を低減するアンチバイブレーションシステムも搭載されています。Stanley STHM5KH は、安全かつ効率的に作業するためのさまざまな機能を備えています。
他の言語で
- English: Stanley STHM5KH User manual