STEL670
3
6
繁体中文
A B
C D
1
2
3
4
3
ENGLISH
STEL670
1500W Heat Gun
SPECIFICATION STEL670
POWER
HEAT SETTING
SWITCH CONTROL
TEMPERATURE
AIR FLOW
CABLE LENGTH
Technical data
Intended Use
Your Stanley heat gun has been designed for various heating
applications (eg. Paint stripping)
General safety rules
Warning! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains operated (corded)
power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
toolin unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust related hazards.
h. Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Before drilling into walls, floors or ceilings check for the
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
W
°C
l/mim
m
1500
Variable
2 Stage ( I/ II)
50-450/ 90-600
300/ 500
2
4
ENGLISH
• Do not burn the paint. Keep the nozzle at least 25mm
(1”) from the surface as this keeps the temperature below
the required 450°C. If you are scraping from a vertical
position then you should scrape downwards to prevent
the paint from falling back into the heat gun and burning.
Dispose of all paint debris safely and ensure that the
work area is thoroughly cleaned after completing the job.
• Do not use in a damp atmosphere or where
flammable gases may be present or use near
combustible materials. Spaces behind boards, ceilings
and floors and wall cavities in timber frame constructed
houses can contain flammable materials. Check before
using the heat gun.
• Allow the tool to cool fully before storing.
• Ensure adequate ventilation when using heat guns as
toxic fumes may be produced.
• Do not use as a hairdryer! The air temperature is far
higher than a hairdryer.
• Do not obstruct either the air intake or nozzle outlet as
this may cause excessive heat build up resulting in
damage to the tool.
• Do not direct the hot air blast at other people.
• Do not touch the metal nozzle as it becomes very hot
during use and remains hot for up to 30 minutes after use.
Do not look down the nozzle while the unit is working
because of the high temperatures being produced.
• Do not allow paint to adhere to the nozzle or scraper
as it could ignite after a time.
• Do not operate your heat gun whilst it is hanging by
the hanging hook.
• A fire may arise if the appliance is not used with
care.
• Do not place the nozzle against anything while
using or immediately after use.
• Do not poke anything down the nozzle as it could
give you an electric shock.
Features (fig. A)
1. Switch
2. Heat control knob
3. Ventilation slots
4. Nozzle
Handling Your Heat Gun
Do not place your hand over the ventilation slots (3) or block
these vents in any way. This restricts the airflow through the
element and causes over heating.
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
Additional Safety Instructions for Heat Guns
• Always switch off before putting tool down.
• Extreme care should be taken when stripping
paint, the peelings, residue and vapors of paint may
contain lead, which is poisonous. Once deposited on
surfaces, hand to mouth contact can result in the
ingestion of lead. Exposures to even low levels of lead
can caused irreversible brain and nervous system
damage; young and unborn children are particularly
vulnerable. Do not smoke, eat or drink in a work area
that could or may be contaminated by lead. Lead based
paints should only be removed by a professional
and should not be removed using a heat gun.
• When removing paints you should ensure that your
work area is enclosed. It is advisable to wear a dust
mask.
5
ENGLISH
Setting the temperature (fig. B)
• To increase the temperature setting, turn the heat control
knob (2) anti-clockwise.
• To reduce the temperature setting, turn the heat control
knob clockwise.
Operating Your Heat Gun (fig. C)
• To switch your heat gun on at the low temperature setting,
press the switch (1) to depress to position “I”.
• To switch the tool on at the high temperature setting, set
the switch (1) to position “II”.
• To switch the tool off, set the on/off switch (1) to position
“0”.
Note: Allow the element to heat up for a few seconds before
use. Initially, some smoke may emit from your heat gun. This
is normal and will soon cease.
Cooling Down
In use, the nozzle (4) of your heat gun becomes extremely hot.
Great care is necessary when cooling your heat gun after use.
Hands Free Use (fig. D)
This tool can also be used in stationary mode.
• Place the tool onto a firm and stable surface as shown.
• Always point your heat gun away from you.
• Secure the cable to prevent pulling your heat gun off the
stand.
Do not touch the nozzle (4) and ensure that nothing is
dropped into the nozzle. Carefully switch off your heat gun
and then allow it to cool
Paint Stripping
Your heat gun is designed to soften paint and lacquer enabling
it to be removed using a good quality hand scraper.
Proceed as follows: Direct the hot air onto the area to be
removed. When the paint softens, scrape firmly. Experiment
to establish the length of time necessary to apply the heat to
obtain optimum results. Scrape the softened paint immediately
or it will harden again.
Your heat gun is not suitable for stripping metal-framed
windows. This is because the heat from the heat gun is
conducted through the metal and can crack the glass. Scrape
with the grain of the wood wherever possible. Do not linger on
one spot for too long as the surface may char or ignite.
Accessories
The performance of your tool depends on the accessory used.
Stanley and Piranha accessories are engineered to high
quality standards and designed to enhance the performance of
your tool. By using these accessories you will get the very
best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
• Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
• Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and used
again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
6
STEL670
1500
STEL670
1500
2 ( I/ II)
50-450/ 90-600
l/mim 300/ 500
m
2
Stanley
/
1.
a.
b.
c.
2.
a.
b.
c.
d.
e.
3.
a.
b.
c.
d.
e.
f.
g.
h.
4.
a.
b.
c.
d.
7
e.
f.
g.
5.
a.
•
•
•
• 25
mm (1) 450C
•
•
•
•
•
•
•
•
•
•
•
•
A
1.
2.
3.
4.
(3)
B
• (2)
•
C
• (1)
I
• (1)
II
• on/off (1)
0
(4)
D
8
•
•
•
(4)
Stanley and
Piranha
•
•
Stanley
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
他の言語で
- English: Stanley STEL670 User manual
関連論文
その他のドキュメント
-
DeWalt DCE530 ユーザーマニュアル
-
Hitachi RH600T Handling Instructions Manual
-
Metabo HE 20-600 取扱説明書
-
Leister SOLANO AT ユーザーマニュアル
-
-
Pro sKit SS-615 Adjustable Temperature Heat Gun ユーザーマニュアル
-
-
Atten AT-2190 ユーザーマニュアル
-
BLACK+DECKER BW17 ユーザーマニュアル
-
Pro'sKit SS-628F 取扱説明書
