Stanley STEL201 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
2
6
STEL201
FIG D
FIG E
1
3
4
2
6
5
FIG A
FIG B
2
FIG F
FIG C
1
1
2
ENGLISH
Intended use
Your Stanley impact wrench has been designed for
screwdriving and nut setting applications.
SAFETY INSTRUCTIONS
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Technical data
STEL201SPECIFICATION
STEL201
IMPACT DRIVER
Reveres
Yes
Beats/Min
bpm 0-3500
Ampers
A 4.3
Voltage
V 110
Chuck Type
mm 6.35
Speed
rpm 0-2900
Max.torque
Nm 146
Cable length
m 2.2
Power
W 450
3
ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
ADDITIONAL POWER TOOL SAFETY WARNINGS
Warning! Additional safety warnings for impact
wrenches
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Warning! impact wrenches are not torque
wrenches. Do not use this tool for tightening
calibrated torque measurement device such as
a torque wrench should be used when under
tightened or over tightened fasteners can lead to
the failure of the joint.
SAFETY OF OTHERS
This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
play with the appliance.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Impairment of hearing.
Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
keep your hair, clothing, and gloves away from air
vents. Air vents often cover moving parts in which these
items can be caught.
Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips to fly.
Flying particles can cause permanent eye damage.
Bits, sockets and tools get hot during operation.
Wear gloves when touching them.
Do not operate this tool for long periods of time.
Vibration caused by tool action may be harmful to your
hands and arms. Use gloves to provide extra cushion
and limit exposure by taking frequent rest periods.
Wear appropriate personal hearing protection during
use. Under some conditions and duration of use, noise
from this product may contribute to hearing loss.
4
ENGLISH
LABELS ON TOOL
The following symbols are shown on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
FEATURES
DATE CODE POSITION (FIG B)
This tool includes some or all of the following features (Figure A).
1. Trigger switch
2. Forward/Reverse button
3. Chuck collar
4. 1/4 inch hex quick-release chuck
5. Magnetic Bit holder
6. Belt hook
OPERATION
@
WARNING: To reduce the risk of injury, always unplug
tool from power supply before making any adjustments or
changing accessories.
VARIABLE SPEED TRIGGER SWITCH (FIGURE C)
To turn the tool on, squeeze the trigger switch (1). To turn the
tool off, release the trigger switch. Your tool is
equipped with a brake. The chuck will stop as soon as the
trigger switch is fully released. The variable speed switch
enables you to select the best speed for a particular
application. The more you squeeze the trigger, the faster the
tool will operate. Use lower speeds for starting holes without a
center punch, drilling in metals or plastics, or driving screws.
For maximum tool life, use variable speed only for starting
holes or fasteners.
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should be
avoided.
QUICK RELEASE CHUCK (FIGURE D, E)
NOTE: The chuck accepts 1/4 inch (6.35 mm) hex accessories
only.
@
WARNING: Ensure the tool is unplugged to prevent
switch actuation before installing or removing accessories.
To install an accessory, firmly insert the accessory
completely into the quick release chuck (4) until an audible
click is heard and verify the accessory is locked into place
by tugging on it.
• To remove an accessory, pull the chuck collar (3) away
from the front of the tool, remove the accessory and
release the collar.
NOTE: The quick release chuck is spring-loaded. The
accessory will be ejected when the chuck collar is pulled
forward.
BIT TIP STORAGE
A magnetic bit storage slot (5) is built into the top of the tool
for easy bit storage and access
BELT CLIP (FIGURE F)
WARNING: Ensure the tool is unplugged to prevent
switch actuation before installing or removing accessories.
A belt clip (6) is provided which can be switched to either
side of the tool based on user preference for convenient
access and storage during use.
Attach the belt clip by inserting the tab on the belt clip into
the slot on the drill handle as shown in figure F.
Secure the belt clip to the handle with the supplied screw
and firmly tighten with a phillips screwdriver.
MAINTENANCE
Your Stanley tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous-
satisfactory operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
PROTECTING THE ENVIRONMENTS
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail
able for separate collection.
z
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials
helps prevent environmental pollution and reduces the
demand for raw materials.
The Date Code (1), which also includes the year of manufacture,
is printed into the housing.
Example: 2013 XX XX
Year of Manufacture
5
ENGLISH
NOTES
Stanley's policy is one of continuous improvement to our
products and, as such, we reserve the right tochange
product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
6
Stanley
/
1.
a.
b.
c.
STEL201
V 110
A 4.3
w 450
mm 6.35
/ 0-2900
/ bpm 0-3500
Nm 146
2.2
2.
a.
b.
c.
d.
e.
f.
(RCD) RCD
3.
a.
b.
c. /
d.
e.
f.
g.
STEL201
7
4.
a.
b.
c.
/
d.
e.
f.
g.
5.
a.






/









(MDF)
8
B
日期代碼(1)也包括製造年月,已經印在工具外
殼上。
範例
: 2013 XX XX
製造年份
周數
A
1.
2. /
3.
4. 1/4"
5.
6.
B
(1)
DE
1/4" (6.35 mm)
(4)
(3)
(5)
F
(6)
F
Stanley



Stanley
 Stanley
9
/
/
Stanley
90621066 03/2015
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Stanley STEL201 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で