3
STDC1804
STDC1802
10
B
1
2
FIG A
FIG B
FIG D
FIG C
FIG E
2
1
3
4
5
7
8
9
11
12
10
6
5
4
FIG F FIG G
FIG H
FIG J
I1
I2
FIG I
3
11
J1
J2
3
ENGLISH
Intended use
Your Stanley Cordless Drill/Driver has been designed for
screwdriving and nut setting applications.
SAFETY INSTRUCTIONS
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Technical data
STDC1802STDC1804
TYPE
Voltage V
DC
No-load speed /min
Max. torque
(PTI Rating)
Nm
Chuck capacity mm
Weight kg
18
0-400/0-1600
30
13
1.90
1.61
Charger
Input Voltage
V
AC
Output Voltage V
DC
Output Current(DC) A
Approx. charge time min
220
20
2
60-120
Battery
Voltage
V
DC
Capacity Ah
18
4.0
18
0-400/0-1600
30
13
1.61
220
20
2
60
18
2.0
Type Li-Ion
STDC1804/STDC1802
18V LI-ION Cordless Drill/Driver
STBL184L STBL182L
(with 2Ah battery)
(with 4Ah battery)
4
ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a.
manufacturer. A charger that is suitable for one type of
another battery pack.
b.
battery packs. Use of any other battery packs may create
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
ADDITIONAL POWER TOOL SAFETY WARNINGS
Warning! Additional safety warnings for impact
wrenches
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces when
performing an operation where cutting accessory may
contact hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
SAFETY OF OTHERS
This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
play with the appliance.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Impairment of hearing.
Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
5
ENGLISH
LABELS ON TOOL
The following symbols are shown on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
Do not expose the battery to water.
Do not store in locations where the temperature may
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
40 °C.
Charge only using the charger provided with the tool.
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
CHARGERS
Use your Stanley charger only to charge the battery in
the tool with which it was supplied. Other batteries could
burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Service Centre in
order to avoid a hazard.
FEATURES
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGERS
This tool includes some or all of the following features (Figure A).
SAVE THESE INSTRUCTIONS: This manual contains
important safety instructions for battery chargers.
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only designated Stanley batteries. Other types of
batteries may burst causing personal injury and damage.
CAUTION: Under certain conditions, with the charger
plugged in to the power supply, the charger can be
shorted by foreign material. Foreign materials of a
conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to
clean.
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The
charger and battery pack are specifically designed to work
together.
These chargers are not intended for any uses other
than charging designated Stanley rechargeable
batteries. Any other uses may result in risk of fire,
electric shock or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in
risk of fire, electric shock, or electrocution.
An extension cord must have adequate wire size for
safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has
more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each
individual extension contains at least the minimum wire
size.
Do not place any object on top of charger or place the
charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
Do not operate charger with damaged cord or plug —
have them replaced immediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized service center.
Do not disassemble charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock,
electrocution or fire.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard
household electrical power. Do not attempt to use it
on any other voltage.
SAVE THESE INSTRUCTIONS
Important Safety Instruction for Battery Packs
WARNING: For safe operation, read this manual and
manuals originally supplied with tool before using the
charger.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures
outlined.
Read all Instructions
Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when LI-ION battery packs are
burned.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte for Li-ion
batteries is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
Charge the battery packs only in Stanley chargers.
DO NOT splash or immerse in water or other liquids.
This may cause premature cell failure.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
105°F (40C°) (such as outside sheds or metal
buildings in summer).
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery packs should be
returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry battery
so that metal objects can contact exposed battery
terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like.
NOTE: LI-ION batteries should not be put in checked
baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold.
2. Long storage will not harm the battery pack or charger.
CHARGING PROCEDURE
Stanley chargers are designed to charge
Stanley battery packs in 40-60 minutes depending on the pack
being charged.
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger. (Fig. B)
3. The LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
CHARGER DIAGNOSTICS
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems are
indicated by one LED flashing in different patterns.
BAD BATTERY
The charger can detect a weak or damaged battery.
The LED flashes in the pattern indicated on the label. If
you see this bad battery blink pattern, do not continue
to charge the battery. Return it to a service center or a
collection site for recycling.
HOT/COLD PACK DELAY
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a
Hot/Cold Pack Delay, suspending charging until the
battery has normalized. After this happens, the
charger automatically switches to the Pack Charging
mode. This feature ensures maximum battery life. The
light flashes in the pattern indicated on the label.
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery pack
fresh and fully charged. This charger features an automatic
tune-up mode which equals or balances the individual cells in
the battery pack to allow it to function at peak capacity. Battery
packs should be tuned up weekly or whenever the battery no
longer delivers the same amount of work. To use the automatic
tune-up mode, place the battery pack in the charger and leave
it for at least 8 hours.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the
battery pack is charged when the air temperature is
between 65°F and 75°F (18- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in
a warm environment such as in a metal shed, or an
uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or
other appliance
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location where the
surrounding air temperature is approximately 65 - 75°F
(18- 24°C).
d. If charging problems persist, take the tool, battery pack
and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not
limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
6. Do not freeze or immerse charger in water or any other
liquid.
@ WARNING: Shock hazard. Do not allow any liquid to get
inside charger.Never attempt to open the battery pack for
any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
OPERATING INSTRUCTIONS
Installing and Removing the Battery Pack From the Tool
CAUTION: Make certain the lock-off button is engaged to
prevent switch actuation before emoving or installing
battery.
1. TO INSTALL BATTERY PACK: Insert battery pack (7)
firmly into tool until an audible click is heard as shown in
figure C.
2. TO REMOVE BATTERY PACK: Depress the battery
release button (8) as shown in figure D and pull battery
pack out of tool.
3. Trigger Switch & forward/Reverse Button - figure E
• The drill is turned ON and OFF by pulling and releasing
the trigger switch (1) shown in figure E. The farther the
trigger is depressed, the higher the speed of the drill.
• A forward/reverse control button (2) determines the
rotational direction of the tool and also serves as a lock off
button.
• To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right
side of the tool.
• To select reverse, depress the forward/reverse control
button on the left side of the tool.
• The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger is released.
4. Adjusting Torque Control - figure f
This tool is fitted with a torque adjustment collar (3)
to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece
materials require a higher torque setting than small screws
and soft workpiece materials.
• For drilling in wood, metal and plastics, set the collar to the
drilling position symbol
• For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriatesetting, proceed as
follows:
• Set the collar to the lowest torque setting.
• Tighten the first screw.
• If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
5. Dual Range Gearing - figure G
The dual range feature of your drill allows you to shift
gears for greater versatility.
• To select low speed, high torque setting (position1), turn
tool off and permit to stop. Slide gear shifter button (4)
away from the chuck.
• To select the high speed, low torque setting (position 2),
turn tool off and permit to stop. Slide gear shifter button
back toward the chuck.
NOTE: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual
range gear button is either completely pushed forward or
completely pushed back.
6. keyless Chuck - figure H
@ WARNING: Make certain the battery pack is removed to
prevent tool actuation before installing or removing
accessories.
To insert a drill bit or other accessory:
• Grasp the chuck (5) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
• Insert the bit or other accessory fully into the chuck, and
tighten securely by rotating the chuck in the clockwise
direction as viewed from the chuck end.
@ WARNING: Do not attempt to tighten or loosen drill bits (or
any other accessory) by gripping the front part of the chuck
and turning the tool on. Damage to the chuck and personal
injury may occur when changing accessories.
7. Screw Driving
• For driving fasteners, the forward/reverse button should be
pushed to the left.
• Use reverse (button pushed to the right) for removing
fasteners.
NOTE: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
8. Drilling
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the
Safety Instructions.
• Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
• Secure and maintain work area, as instructed in the Safety
Instructions.
• Run the drill very slowly, using light pressure, until the hole
is started enough to keep the drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
• Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area or the auxillary handle if provided.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
• Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
• Make sure switch turns drill on and off.
1) Drilling in Wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling to
clear chips from the flutes.
2) Drilling in Metal
Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled
dry. The cutting lubricants that work best are sulfurized
cutting oil or lard oil.
3) Drilling in Masonry
Use carbide tipped masonry bits. Refer to Drilling section.
Keep even force on the drill but not so much that you crack
the brittle material. A smooth, even flow of dust indicates
the proper drilling rate.
9. LED Work Light
When drill is activated by pulling the trigger switch
(1), the integrated LED work light (10) will automatically
illuminate the work area.
NOTE: he work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
10. Bit Tip Storage
Two magnetic bit storage slots (6) are built into the area on
the top of the tool.
1) Battery fuel Gauge - figure I
The tool is equipped with a battery fuel gauge (9). This can
be used to display the current level of charge in the battery
during use and during charging. It does not indicate tool
functionality and is subject to variation based on product
components, temperature and end-user application.
Checking battery charge during use:
• Press the battery fuel gauge button (I1).
• The three LEDs (I2) will illuminate indicating the percent of
charge in the battery (figure I).
• If LED light does not lluminate, charge battery.
NOTE: This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery
charge is depleted, the tool will not operate until after the
battery has been recharged.
2) Belt Clip - figure J
A belt clip (11) is provided which can be switched to either side
of the tool based on user preference for convenient access
and storage during use.
• Place the front lip of the belt clip (J1) into the indentation of
the base (J2).
• Secure the belt clip with the supplied screw and firmly
tighten with a phillips screwdriver.
@ WARNING: Ensure the forward/reverse control button (2)
is in the center lock position before attaching tool to belt.
MAINTENANCE
Your Stanley tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuoussatisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart
from regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger
before cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
PROTECTING THE ENVIRONMENTS
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
avail able for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
BATTERIES
Run the battery down completely, then remove it
from the tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
SERVICE INFORMATION
Stanley offers a full network of company-owned and
authorized service locations throughout Asia. All Stanley
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service.Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Stanley
1. Trigger Switch
2. Forward/Reverse Button
3. Torque Adjust Collar
4. Dual Range Gear Selector
5. Keyless Chuck
6. Magnetic Bit Tip Holders (2)
7. Battery
8. Battery Release Button
9. Battery Fuel Gauge
10. LED Work Light
11. Belt Clip
location nearest to you.
NOTES
Stanley's policy is one of continuous improvement to our
products and, as such, we reserve the right tochange
product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
DATE CODE POSITION (Figure A)
The Date Code (12), which also includes the year of
manufacture, is printed into the housing.
Example: 2013 XX XX
Year of Manufacture
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
6
ENGLISH
5
charger. This will reduce risk of damage to electric plug
and cord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in
risk of fire, electric shock, or electrocution.
An extension cord must have adequate wire size for
safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has
more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each
individual extension contains at least the minimum wire
size.
Do not place any object on top of charger or place the
charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
Do not operate charger with damaged cord or plug —
have them replaced immediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized service center.
Do not disassemble charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock,
electrocution or fire.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard
household electrical power. Do not attempt to use it
on any other voltage.
SAVE THESE INSTRUCTIONS
Important Safety Instruction for Battery Packs
WARNING: For safe operation, read this manual and
manuals originally supplied with tool before using the
charger.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures
outlined.
Read all Instructions
Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when LI-ION battery packs are
burned.
Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte for Li-ion
batteries is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
Charge the battery packs only in Stanley chargers.
DO NOT splash or immerse in water or other liquids.
This may cause premature cell failure.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
105°F (40C°) (such as outside sheds or metal
buildings in summer).
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery packs should be
returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry battery
so that metal objects can contact exposed battery
terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like.
NOTE: LI-ION batteries should not be put in checked
baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold.
2. Long storage will not harm the battery pack or charger.
CHARGING PROCEDURE
Stanley chargers are designed to charge
Stanley battery packs in 60-120 minutes depending on the pack
being charged.
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger. (Fig. B)
3. The LED will flash indicating that the battery is
7
ENGLISH
SAVE THESE INSTRUCTIONS: This manual contains
important safety instructions for battery chargers.
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only designated Stanley batteries. Other types of
batteries may burst causing personal injury and damage.
CAUTION: Under certain conditions, with the charger
plugged in to the power supply, the charger can be
shorted by foreign material. Foreign materials of a
conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to
clean.
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The
charger and battery pack are specifically designed to work
together.
These chargers are not intended for any uses other
than charging designated Stanley rechargeable
batteries. Any other uses may result in risk of fire,
electric shock or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in
risk of fire, electric shock, or electrocution.
An extension cord must have adequate wire size for
safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has
more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each
individual extension contains at least the minimum wire
size.
Do not place any object on top of charger or place the
charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
Do not operate charger with damaged cord or plug —
have them replaced immediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized service center.
Do not disassemble charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock,
electrocution or fire.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard
household electrical power. Do not attempt to use it
on any other voltage.
SAVE THESE INSTRUCTIONS
Important Safety Instruction for Battery Packs
WARNING: For safe operation, read this manual and
manuals originally supplied with tool before using the
charger.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures
outlined.
Read all Instructions
Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when LI-ION battery packs are
burned.
Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte for Li-ion
batteries is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
Charge the battery packs only in Stanley chargers.
DO NOT splash or immerse in water or other liquids.
This may cause premature cell failure.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
105°F (40C°) (such as outside sheds or metal
buildings in summer).
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery packs should be
returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry battery
so that metal objects can contact exposed battery
terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like.
NOTE: LI-ION batteries should not be put in checked
baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold.
2. Long storage will not harm the battery pack or charger.
CHARGING PROCEDURE
Stanley chargers are designed to charge
Stanley battery packs in 40-60 minutes depending on the pack
being charged.
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger. (Fig. B)
3. The LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
CHARGER DIAGNOSTICS
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems are
indicated by one LED flashing in different patterns.
BAD BATTERY
The charger can detect a weak or damaged battery.
The LED flashes in the pattern indicated on the label. If
you see this bad battery blink pattern, do not continue
to charge the battery. Return it to a service center or a
collection site for recycling.
HOT/COLD PACK DELAY
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a
Hot/Cold Pack Delay, suspending charging until the
battery has normalized. After this happens, the
charger automatically switches to the Pack Charging
mode. This feature ensures maximum battery life. The
light flashes in the pattern indicated on the label.
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery pack
fresh and fully charged. This charger features an automatic
tune-up mode which equals or balances the individual cells in
the battery pack to allow it to function at peak capacity. Battery
packs should be tuned up weekly or whenever the battery no
longer delivers the same amount of work. To use the automatic
tune-up mode, place the battery pack in the charger and leave
it for at least 8 hours.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the
battery pack is charged when the air temperature is
between 65°F and 75°F (18- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in
a warm environment such as in a metal shed, or an
uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or
other appliance
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location where the
surrounding air temperature is approximately 65 - 75°F
(18- 24°C).
d. If charging problems persist, take the tool, battery pack
and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not
limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
6. Do not freeze or immerse charger in water or any other
liquid.
@ WARNING: Shock hazard. Do not allow any liquid to get
inside charger.Never attempt to open the battery pack for
any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
OPERATING INSTRUCTIONS
Installing and Removing the Battery Pack From the Tool
CAUTION: Make certain the lock-off button is engaged to
prevent switch actuation before emoving or installing
battery.
1. TO INSTALL BATTERY PACK: Insert battery pack (7)
firmly into tool until an audible click is heard as shown in
figure C.
2. TO REMOVE BATTERY PACK: Depress the battery
release button (8) as shown in figure D and pull battery
pack out of tool.
3. Trigger Switch & forward/Reverse Button - figure E
• The drill is turned ON and OFF by pulling and releasing
the trigger switch (1) shown in figure E. The farther the
trigger is depressed, the higher the speed of the drill.
• A forward/reverse control button (2) determines the
rotational direction of the tool and also serves as a lock off
button.
• To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right
side of the tool.
• To select reverse, depress the forward/reverse control
button on the left side of the tool.
• The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger is released.
4. Adjusting Torque Control - figure f
This tool is fitted with a torque adjustment collar (3)
to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece
materials require a higher torque setting than small screws
and soft workpiece materials.
• For drilling in wood, metal and plastics, set the collar to the
drilling position symbol
• For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriatesetting, proceed as
follows:
• Set the collar to the lowest torque setting.
• Tighten the first screw.
• If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
5. Dual Range Gearing - figure G
The dual range feature of your drill allows you to shift
gears for greater versatility.
• To select low speed, high torque setting (position1), turn
tool off and permit to stop. Slide gear shifter button (4)
away from the chuck.
• To select the high speed, low torque setting (position 2),
turn tool off and permit to stop. Slide gear shifter button
back toward the chuck.
NOTE: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual
range gear button is either completely pushed forward or
completely pushed back.
6. keyless Chuck - figure H
@ WARNING: Make certain the battery pack is removed to
prevent tool actuation before installing or removing
accessories.
To insert a drill bit or other accessory:
• Grasp the chuck (5) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
• Insert the bit or other accessory fully into the chuck, and
tighten securely by rotating the chuck in the clockwise
direction as viewed from the chuck end.
@ WARNING: Do not attempt to tighten or loosen drill bits (or
any other accessory) by gripping the front part of the chuck
and turning the tool on. Damage to the chuck and personal
injury may occur when changing accessories.
7. Screw Driving
• For driving fasteners, the forward/reverse button should be
pushed to the left.
• Use reverse (button pushed to the right) for removing
fasteners.
NOTE: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
8. Drilling
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the
Safety Instructions.
• Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
• Secure and maintain work area, as instructed in the Safety
Instructions.
• Run the drill very slowly, using light pressure, until the hole
is started enough to keep the drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
• Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area or the auxillary handle if provided.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
• Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
• Make sure switch turns drill on and off.
1) Drilling in Wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling to
clear chips from the flutes.
2) Drilling in Metal
Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled
dry. The cutting lubricants that work best are sulfurized
cutting oil or lard oil.
3) Drilling in Masonry
Use carbide tipped masonry bits. Refer to Drilling section.
Keep even force on the drill but not so much that you crack
the brittle material. A smooth, even flow of dust indicates
the proper drilling rate.
9. LED Work Light
When drill is activated by pulling the trigger switch
(1), the integrated LED work light (10) will automatically
illuminate the work area.
NOTE: he work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
10. Bit Tip Storage
Two magnetic bit storage slots (6) are built into the area on
the top of the tool.
1) Battery fuel Gauge - figure I
The tool is equipped with a battery fuel gauge (9). This can
be used to display the current level of charge in the battery
during use and during charging. It does not indicate tool
functionality and is subject to variation based on product
components, temperature and end-user application.
Checking battery charge during use:
• Press the battery fuel gauge button (I1).
• The three LEDs (I2) will illuminate indicating the percent of
charge in the battery (figure I).
• If LED light does not lluminate, charge battery.
NOTE: This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery
charge is depleted, the tool will not operate until after the
battery has been recharged.
2) Belt Clip - figure J
A belt clip (11) is provided which can be switched to either side
of the tool based on user preference for convenient access
and storage during use.
• Place the front lip of the belt clip (J1) into the indentation of
the base (J2).
• Secure the belt clip with the supplied screw and firmly
tighten with a phillips screwdriver.
@ WARNING: Ensure the forward/reverse control button (2)
is in the center lock position before attaching tool to belt.
MAINTENANCE
Your Stanley tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuoussatisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart
from regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger
before cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
PROTECTING THE ENVIRONMENTS
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
avail able for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
BATTERIES
Run the battery down completely, then remove it
from the tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
SERVICE INFORMATION
Stanley offers a full network of company-owned and
authorized service locations throughout Asia. All Stanley
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service.Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Stanley
location nearest to you.
NOTES
Stanley's policy is one of continuous improvement to our
products and, as such, we reserve the right tochange
product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
8
ENGLISH
SAVE THESE INSTRUCTIONS: This manual contains
important safety instructions for battery chargers.
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only designated Stanley batteries. Other types of
batteries may burst causing personal injury and damage.
CAUTION: Under certain conditions, with the charger
plugged in to the power supply, the charger can be
shorted by foreign material. Foreign materials of a
conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to
clean.
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The
charger and battery pack are specifically designed to work
together.
These chargers are not intended for any uses other
than charging designated Stanley rechargeable
batteries. Any other uses may result in risk of fire,
electric shock or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in
risk of fire, electric shock, or electrocution.
An extension cord must have adequate wire size for
safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has
more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each
individual extension contains at least the minimum wire
size.
Do not place any object on top of charger or place the
charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
Do not operate charger with damaged cord or plug —
have them replaced immediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized service center.
Do not disassemble charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock,
electrocution or fire.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard
household electrical power. Do not attempt to use it
on any other voltage.
SAVE THESE INSTRUCTIONS
Important Safety Instruction for Battery Packs
WARNING: For safe operation, read this manual and
manuals originally supplied with tool before using the
charger.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures
outlined.
Read all Instructions
Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when LI-ION battery packs are
burned.
Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte for Li-ion
batteries is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
Charge the battery packs only in Stanley chargers.
DO NOT splash or immerse in water or other liquids.
This may cause premature cell failure.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
105°F (40C°) (such as outside sheds or metal
buildings in summer).
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery packs should be
returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry battery
so that metal objects can contact exposed battery
terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like.
NOTE: LI-ION batteries should not be put in checked
baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold.
2. Long storage will not harm the battery pack or charger.
CHARGING PROCEDURE
Stanley chargers are designed to charge
Stanley battery packs in 40-60 minutes depending on the pack
being charged.
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger. (Fig. B)
3. The LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
CHARGER DIAGNOSTICS
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems are
indicated by one LED flashing in different patterns.
BAD BATTERY
The charger can detect a weak or damaged battery.
The LED flashes in the pattern indicated on the label. If
you see this bad battery blink pattern, do not continue
to charge the battery. Return it to a service center or a
collection site for recycling.
HOT/COLD PACK DELAY
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a
Hot/Cold Pack Delay, suspending charging until the
battery has normalized. After this happens, the
charger automatically switches to the Pack Charging
mode. This feature ensures maximum battery life. The
light flashes in the pattern indicated on the label.
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery pack
fresh and fully charged. This charger features an automatic
tune-up mode which equals or balances the individual cells in
the battery pack to allow it to function at peak capacity. Battery
packs should be tuned up weekly or whenever the battery no
longer delivers the same amount of work. To use the automatic
tune-up mode, place the battery pack in the charger and leave
it for at least 8 hours.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the
battery pack is charged when the air temperature is
between 65°F and 75°F (18- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in
a warm environment such as in a metal shed, or an
uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or
other appliance
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location where the
surrounding air temperature is approximately 65 - 75°F
(18- 24°C).
d. If charging problems persist, take the tool, battery pack
and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not
limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
6. Do not freeze or immerse charger in water or any other
liquid.
@ WARNING: Shock hazard. Do not allow any liquid to get
inside charger.Never attempt to open the battery pack for
any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
OPERATING INSTRUCTIONS
Installing and Removing the Battery Pack From the Tool
CAUTION: Make certain the lock-off button is engaged to
prevent switch actuation before emoving or installing
battery.
1. TO INSTALL BATTERY PACK: Insert battery pack (7)
firmly into tool until an audible click is heard as shown in
figure C.
2. TO REMOVE BATTERY PACK: Depress the battery
release button (8) as shown in figure D and pull battery
pack out of tool.
3. Trigger Switch & forward/Reverse Button - figure E
• The drill is turned ON and OFF by pulling and releasing
the trigger switch (1) shown in figure E. The farther the
trigger is depressed, the higher the speed of the drill.
• A forward/reverse control button (2) determines the
rotational direction of the tool and also serves as a lock off
button.
• To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right
side of the tool.
• To select reverse, depress the forward/reverse control
button on the left side of the tool.
• The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger is released.
4. Adjusting Torque Control - figure f
This tool is fitted with a torque adjustment collar (3)
to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece
materials require a higher torque setting than small screws
and soft workpiece materials.
• For drilling in wood, metal and plastics, set the collar to the
drilling position symbol
• For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriatesetting, proceed as
follows:
• Set the collar to the lowest torque setting.
• Tighten the first screw.
• If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
5. Dual Range Gearing - figure G
The dual range feature of your drill allows you to shift
gears for greater versatility.
• To select low speed, high torque setting (position1), turn
tool off and permit to stop. Slide gear shifter button (4)
away from the chuck.
• To select the high speed, low torque setting (position 2),
turn tool off and permit to stop. Slide gear shifter button
back toward the chuck.
NOTE: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual
range gear button is either completely pushed forward or
completely pushed back.
6. keyless Chuck - figure H
@ WARNING: Make certain the battery pack is removed to
prevent tool actuation before installing or removing
accessories.
To insert a drill bit or other accessory:
• Grasp the chuck (5) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
• Insert the bit or other accessory fully into the chuck, and
tighten securely by rotating the chuck in the clockwise
direction as viewed from the chuck end.
@ WARNING: Do not attempt to tighten or loosen drill bits (or
any other accessory) by gripping the front part of the chuck
and turning the tool on. Damage to the chuck and personal
injury may occur when changing accessories.
7. Screw Driving
• For driving fasteners, the forward/reverse button should be
pushed to the left.
• Use reverse (button pushed to the right) for removing
fasteners.
NOTE: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
8. Drilling
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the
Safety Instructions.
• Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
• Secure and maintain work area, as instructed in the Safety
Instructions.
• Run the drill very slowly, using light pressure, until the hole
is started enough to keep the drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
• Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area or the auxillary handle if provided.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
• Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
• Make sure switch turns drill on and off.
1) Drilling in Wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling to
clear chips from the flutes.
2) Drilling in Metal
Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled
dry. The cutting lubricants that work best are sulfurized
cutting oil or lard oil.
3) Drilling in Masonry
Use carbide tipped masonry bits. Refer to Drilling section.
Keep even force on the drill but not so much that you crack
the brittle material. A smooth, even flow of dust indicates
the proper drilling rate.
9. LED Work Light
When drill is activated by pulling the trigger switch
(1), the integrated LED work light (10) will automatically
illuminate the work area.
NOTE: he work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
10. Bit Tip Storage
Two magnetic bit storage slots (6) are built into the area on
the top of the tool.
1) Battery fuel Gauge - figure I
The tool is equipped with a battery fuel gauge (9). This can
be used to display the current level of charge in the battery
during use and during charging. It does not indicate tool
functionality and is subject to variation based on product
components, temperature and end-user application.
Checking battery charge during use:
• Press the battery fuel gauge button (I1).
• The three LEDs (I2) will illuminate indicating the percent of
charge in the battery (figure I).
• If LED light does not lluminate, charge battery.
NOTE: This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery
charge is depleted, the tool will not operate until after the
battery has been recharged.
2) Belt Clip - figure J
A belt clip (11) is provided which can be switched to either side
of the tool based on user preference for convenient access
and storage during use.
• Place the front lip of the belt clip (J1) into the indentation of
the base (J2).
• Secure the belt clip with the supplied screw and firmly
tighten with a phillips screwdriver.
@ WARNING: Ensure the forward/reverse control button (2)
is in the center lock position before attaching tool to belt.
MAINTENANCE
Your Stanley tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuoussatisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart
from regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger
before cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
PROTECTING THE ENVIRONMENTS
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
avail able for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
BATTERIES
Run the battery down completely, then remove it
from the tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
SERVICE INFORMATION
Stanley offers a full network of company-owned and
authorized service locations throughout Asia. All Stanley
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service.Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Stanley
location nearest to you.
NOTES
Stanley's policy is one of continuous improvement to our
products and, as such, we reserve the right tochange
product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
SAVE THESE INSTRUCTIONS: This manual contains
important safety instructions for battery chargers.
Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only designated Stanley batteries. Other types of
batteries may burst causing personal injury and damage.
CAUTION: Under certain conditions, with the charger
plugged in to the power supply, the charger can be
shorted by foreign material. Foreign materials of a
conductive nature such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to
clean.
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The
charger and battery pack are specifically designed to work
together.
These chargers are not intended for any uses other
than charging designated Stanley rechargeable
batteries. Any other uses may result in risk of fire,
electric shock or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in
risk of fire, electric shock, or electrocution.
An extension cord must have adequate wire size for
safety. The smaller the gauge number of the wire, the
greater the capacity of the cable, that is 16 gauge has
more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each
individual extension contains at least the minimum wire
size.
Do not place any object on top of charger or place the
charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
Do not operate charger with damaged cord or plug —
have them replaced immediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized service center.
Do not disassemble charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock,
electrocution or fire.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard
household electrical power. Do not attempt to use it
on any other voltage.
SAVE THESE INSTRUCTIONS
Important Safety Instruction for Battery Packs
WARNING: For safe operation, read this manual and
manuals originally supplied with tool before using the
charger.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures
outlined.
Read all Instructions
Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when LI-ION battery packs are
burned.
Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte for Li-ion
batteries is composed of a mixture of liquid organic
carbonates and lithium salts.
Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
Charge the battery packs only in Stanley chargers.
DO NOT splash or immerse in water or other liquids.
This may cause premature cell failure.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
105°F (40C°) (such as outside sheds or metal
buildings in summer).
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery packs should be
returned to service center for recycling.
WARNING: Fire hazard. Do not store or carry battery
so that metal objects can contact exposed battery
terminals. For example, do not place battery in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like.
NOTE: LI-ION batteries should not be put in checked
baggage.
STORAGE RECOMMENDATIONS
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold.
2. Long storage will not harm the battery pack or charger.
CHARGING PROCEDURE
Stanley chargers are designed to charge
Stanley battery packs in 40-60 minutes depending on the pack
being charged.
1. Plug the charger into an appropriate outlet before
inserting the battery pack.
2. Insert the battery pack into the charger. (Fig. B)
3. The LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
CHARGER DIAGNOSTICS
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems are
indicated by one LED flashing in different patterns.
BAD BATTERY
The charger can detect a weak or damaged battery.
The LED flashes in the pattern indicated on the label. If
you see this bad battery blink pattern, do not continue
to charge the battery. Return it to a service center or a
collection site for recycling.
HOT/COLD PACK DELAY
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a
Hot/Cold Pack Delay, suspending charging until the
battery has normalized. After this happens, the
charger automatically switches to the Pack Charging
mode. This feature ensures maximum battery life. The
light flashes in the pattern indicated on the label.
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery pack
fresh and fully charged. This charger features an automatic
tune-up mode which equals or balances the individual cells in
the battery pack to allow it to function at peak capacity. Battery
packs should be tuned up weekly or whenever the battery no
longer delivers the same amount of work. To use the automatic
tune-up mode, place the battery pack in the charger and leave
it for at least 8 hours.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the
battery pack is charged when the air temperature is
between 65°F and 75°F (18- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in
a warm environment such as in a metal shed, or an
uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or
other appliance
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location where the
surrounding air temperature is approximately 65 - 75°F
ENGLISH
(18- 24°C).
d. If charging problems persist, take the tool, battery pack
and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as, but not
limited to, steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
6. Do not freeze or immerse charger in water or any other
liquid.
@ WARNING: Shock hazard. Do not allow any liquid to get
inside charger.Never attempt to open the battery pack for
any reason. If the plastic housing of the battery pack
breaks or cracks, return to a service center for recycling.
OPERATING INSTRUCTIONS
Installing and Removing the Battery Pack From the Tool
CAUTION: Make certain the lock-off button is engaged to
prevent switch actuation before emoving or installing
battery.
1. TO INSTALL BATTERY PACK: Insert battery pack (7)
firmly into tool until an audible click is heard as shown in
figure C.
2. TO REMOVE BATTERY PACK: Depress the battery
release button (8) as shown in figure D and pull battery
pack out of tool.
3. Trigger Switch & forward/Reverse Button - figure E
• The drill is turned ON and OFF by pulling and releasing
the trigger switch (1) shown in figure E. The farther the
trigger is depressed, the higher the speed of the drill.
• A forward/reverse control button (2) determines the
rotational direction of the tool and also serves as a lock off
button.
• To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right
side of the tool.
• To select reverse, depress the forward/reverse control
button on the left side of the tool.
• The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger is released.
4. Adjusting Torque Control - figure f
This tool is fitted with a torque adjustment collar (3)
to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece
materials require a higher torque setting than small screws
and soft workpiece materials.
• For drilling in wood, metal and plastics, set the collar to the
drilling position symbol
• For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriatesetting, proceed as
follows:
• Set the collar to the lowest torque setting.
• Tighten the first screw.
• If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
5. Dual Range Gearing - figure G
The dual range feature of your drill allows you to shift
gears for greater versatility.
• To select low speed, high torque setting (position1), turn
tool off and permit to stop. Slide gear shifter button (4)
away from the chuck.
• To select the high speed, low torque setting (position 2),
turn tool off and permit to stop. Slide gear shifter button
back toward the chuck.
NOTE: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual
range gear button is either completely pushed forward or
completely pushed back.
6. keyless Chuck - figure H
@ WARNING: Make certain the battery pack is removed to
prevent tool actuation before installing or removing
accessories.
To insert a drill bit or other accessory:
• Grasp the chuck (5) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
• Insert the bit or other accessory fully into the chuck, and
tighten securely by rotating the chuck in the clockwise
direction as viewed from the chuck end.
@ WARNING: Do not attempt to tighten or loosen drill bits (or
any other accessory) by gripping the front part of the chuck
and turning the tool on. Damage to the chuck and personal
injury may occur when changing accessories.
7. Screw Driving
• For driving fasteners, the forward/reverse button should be
pushed to the left.
• Use reverse (button pushed to the right) for removing
fasteners.
NOTE: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
8. Drilling
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the
Safety Instructions.
• Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
• Secure and maintain work area, as instructed in the Safety
Instructions.
• Run the drill very slowly, using light pressure, until the hole
is started enough to keep the drill bit from slipping out of it.
• Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
• Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area or the auxillary handle if provided.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
• Keep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
• Make sure switch turns drill on and off.
1) Drilling in Wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling to
clear chips from the flutes.
2) Drilling in Metal
Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled
dry. The cutting lubricants that work best are sulfurized
cutting oil or lard oil.
3) Drilling in Masonry
Use carbide tipped masonry bits. Refer to Drilling section.
Keep even force on the drill but not so much that you crack
the brittle material. A smooth, even flow of dust indicates
the proper drilling rate.
9. LED Work Light
When drill is activated by pulling the trigger switch
(1), the integrated LED work light (10) will automatically
illuminate the work area.
NOTE: he work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
10. Bit Tip Storage
Two magnetic bit storage slots (6) are built into the area on
the top of the tool.
1) Battery fuel Gauge - figure I
The tool is equipped with a battery fuel gauge (9). This can
be used to display the current level of charge in the battery
during use and during charging. It does not indicate tool
functionality and is subject to variation based on product
components, temperature and end-user application.
Checking battery charge during use:
• Press the battery fuel gauge button (I1).
• The three LEDs (I2) will illuminate indicating the percent of
charge in the battery (figure I).
• If LED light does not lluminate, charge battery.
NOTE: This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery
charge is depleted, the tool will not operate until after the
battery has been recharged.
2) Belt Clip - figure J
A belt clip (11) is provided which can be switched to either side
9
of the tool based on user preference for convenient access
and storage during use.
• Place the front lip of the belt clip (J1) into the indentation of
the base (J2).
• Secure the belt clip with the supplied screw and firmly
tighten with a phillips screwdriver.
@ WARNING: Ensure the forward/reverse control button (2)
is in the center lock position before attaching tool to belt.
MAINTENANCE
Your Stanley tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuoussatisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart
from regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger
before cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
PROTECTING THE ENVIRONMENTS
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
avail able for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
BATTERIES
Run the battery down completely, then remove it
from the tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
SERVICE INFORMATION
Stanley offers a full network of company-owned and
authorized service locations throughout Asia. All Stanley
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service.Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Stanley
location nearest to you.
NOTES
Stanley's policy is one of continuous improvement to our
products and, as such, we reserve the right tochange
product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
10
STDC1804/STDC1802
18 /
/
/
a)
1)
2)
3)
b)
1)
2)
3)
4)
5)
6)
RCD
RCD
c)
1)
2)
3) /
4)
5)
STDC1802STDC1804
类型
电压 伏特
（直流）
空载转速 /分
最大扭矩
（PTI 标称值）
牛米
夹头尺寸 毫米
重量 千克
18
0-400/0-1600
30
13
1.61
1.90
18
0-400/0-1600
30
13
1.61
充电器
输入电压
伏特
（交流）
输出电压 伏特
（直流）
输出电流（直流）
A
大约充电时间 分
220
18
2
60-120
220
18
2
60
电池
STBL184L STBL182L
电压
伏特
（直流）
电池容量 安时
18
4.0
18
2.0
类型 锂离子
(含 2 安时电池)
(含 4 安时电池)
11
6)
7)
d)
1)
2)
3)
4)
5)
6)
7)
e)
1)
2)
3)
4)
f)
1)
u
u
u
u
u
u
/
u
u
u
12
u
1
(12)
2013 XX XX
u
u
u 40 C
u 10 C 40 C
u
u
u
u
u
u
u
u
u
A
1.
2. /
3.
4.
5.
6. (2)
7.
8.
9.
10. LED
11.
13
u
u
u
u
u
u
u
u
16 18
u
u
u
u
u
u 2
u
u
u
u
15
u
u
14
u
u 105 °F (40°C)
1.
2.
60-120
1.
2. B
3. LED
4. LED
LED
LED
/
/
LED
LED
8
1. 65 °F - 75°F (18- 24°C)
+40 °F (+4.5°C)
+105°F (+40.5°C)
2.
3.
a.
b.
15
c.
65 - 75°F (18- 24°C)
d.
4.
5.
6.
1. C (7)
2. D
(8)
3. / - E
(1)
E
• / (2)
•
/
•/
•
4. - f
(3)
•
•
•
•
•
5. - G
/
(4)
• 2
6. - H
• (5)
•
16
7.
• /
•
8.
•
•
•
•
•
•
•
•
•
•
•
1)
2)
3)
9. LED
(1)
LED (10)
10.
(6)
1) - I
(9)
• (I1)
• LED (I2)
( I)
• LED
20%
2) - J
(11)
• (J1) (J2)
• Philips
/
(2)
17
u
u
u
u
u
u
u
90621327 03/2015
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
他の言語で
- English: Stanley STDC1802 User manual
関連論文
その他のドキュメント
-
Hilti SF 10W-A22 ATC Cordless Drill Driver ユーザーマニュアル
-
-
BLACK+DECKER BCD704 ユーザーマニュアル
-
-
Triton T12AD Operating And Safety Instructions Manual
-
DeWalt DCD710 ユーザーマニュアル
-
DeWalt DCD771 ユーザーマニュアル
-
DeWalt DCD796 ユーザーマニュアル
-
Pro's Kit PT-1206 ユーザーマニュアル
-
Philips SCB3065NB/93 ユーザーマニュアル
