STDH7213
ENGLISH 4
10
16
Bahasa Indonesia 22
Tiếng Việt
35
B
A
0000 00-00
5
2
4
3
13
1
11
6
10
9
7
8
4
C
D
12
E
6
7
4
ENGLISH
Intended use
Your Stanley impact drill has been designed for drilling in
wood, metal and concrete. This tool is intended for consumer
use only.
General Power tool Safety Warnings
@
Warning! Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future
reference. The term "power tool" in all of the warnings
listed below refers to your mains operated (corded) power tool
or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Impact Drill STDH7213
-B1 -XD -TW -KR
Voltage V 220-240 220-240 110 220
Frequency Hz 50/60 50/60 60 60
Power input W 720
No-load speed /min 0-3000 (0-2900 TW)
Impact rate IPM 54000 (52200 TW)
Reverse/Forward rotation Yes
Chuck capacity mm 1.5-13
Max capacity mm
- Concrete 16
- Metal 13
-Wood 32
Weight kg 2.5
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the inuence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying
power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before
STDH7213
13mm Impact Drill
Technical data
5
ENGLISH
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate for
which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualied
repair person using only identical
replacement parts. This will ensure that the safety of
the power tool is maintained.
Additional Power Tool Safety Warnings
@
Warning! Additional safety warnings for drills
and impact drills
Drill Safety Warnings
u Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
u Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
u Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contact-
ing a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
u Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the work
by hand or against your body leaves it unstable and may
lead to loss of control.
u Before drilling into walls, oors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u This tool is not intended for use by persons(including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
u This appliance is not intended for use by per-
sons (including children) with reduced physical,
sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been
given supervision or instruction concerning use
6
ENGLISH
of the appliance by a person responsible for
their safety.
u Children should be supervised to ensure that
they do not play with the appliance.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from mis-
use, prolonged use etc. Even with the application
of the relevant safety regulations and the imple-
mentation of safety devices, certain residual risks
can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts,
blades or accessories.
u Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust devel-
oped when using your tool (example:- working
with wood, especially oak, beech and MDF.)
Label on the tool
The following symbols are shown on the tool:
Warning! In order to reduce the risk of
injury, the user must read the manual.
Date code position (g. A)
The date code (13) is printed on the housing of the
tool, which also contains the year of manufacture.
For example: 2014 XX JN
Year of manufacture
Electrical safety
Double insulation measures are taken in
this power tool, so no grounding is needed.
Please check whether the voltage of power
supplied is consistent with the voltage on
the nameplate or not.
u If the wire is damaged, it should be replaced by
the manufacturer or a service center authorized by
Stanley, to avoid danger.
Using an extension cable
If an extension cable is requred, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm2.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Conductor size (mm
2
)
Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Package contents
The package contains:
1 Impact drill
1 Side handle
1 Depth gauge
1 Chuck key
1 Instruction manual
u Check for damage to the tool, parts or accesso-
ries which may have occurred during transport.
u Take the time to thoroughly read and under-
stand this manual prior to operation.
Description (g. A)
1 Variable speed switch
2 Lock-on button
3 Forward/reverse slider
4 Mode selector
5 Ventilation slots
6 Side handle
7 Depth adjustment rod
8 Keyed chuck
9 Sleeve
10 Chuck key
11.Speed dail
7
ENGLISH
Assembly
Warning! Before assembly, please ensure that the
power tool is powered off and the power plug of the
tool is unplugged from the power source.
Selecting the operating mode (g. B)
The tool can be used in two operating modes:
b
Rotary drilling:
for steel, wood and plastics.
q
Impact drilling:
simultaneous rotating and impacting for
concrete and masonry drilling operations.
u Select the required operating mode by rotating
the mode selector (4) to the required position.
Inserting and removing a bit (g. A)
Keyed chuck
u Open the chuck by turning the sleeve (9) coun-
terclockwise and insert the bit shank.
u Put the chuck key (10) into each hole in the
side of the chuck and turn clockwise until tight.
u To remove the bit, proceed in reverse order.
Fitting the side handle (g. A)
The side handle (6) can be tted to suit both
RH- and LH-users.
Always use the drill with the side handle
properly assembled.
u Loosen the side handle.
u For RH-users, slide the side handle clamp over-
the collar behind the chuck, handle at the left.
u For LH-users, slide the side handle clamp over-
the colar behind the chuck, handle at the right.
u Rotate the side handle to the desired position-
and tighten the handle.
Setting the drilling depth (g. C)
u Insert the required drill bit into the chuck.
u Slacken the side handle (6).
u Fit the depth adjustment rod (7) through the
hole in the side handle clamp.
u Adjust the drilling depth as shown.
u Tighten the side handle.
Forward/reverse slider (g. A)
u To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Chuck removal (g. D)
u Open the chuck jaws as far as possible
u Insert a screwdriver into the chuck and remove
the chuck retaining screw (12) by turning
clockwise.
u Tighten an Allen key into the chuck and strike it
with a hammer as shown.
Instructions for use
u Always observe the safety instructions and ap-
plicable regulations.
u Be aware of the location of pipework and wir-
ing.
u Apply only a gentle pressure to the tool.
Excessive force does not speed up drilling but
decreases tool performance and may shorten
tool life.
u Wear ear protectors with impact drills.Exposure
to noise can cause hearing loss.
u Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
u Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power
tool "live" and shock the operator.
u If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD re-
duces the risk of electric shock.
Prior to operation
u Insert the appropriate bit.
u Mark the spot where the hole is to be drilled.
Proper Hand Position (g. A, E)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the
side handle (6), with the other hand on the main
handle.
Switching on and off
u To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far
8
ENGLISH
you press the switch.
u For continuous operation, press the lock-on but-
ton (2) and release the variable speed switch.
This option is available only at full speed.
u To switch the tool off, release the variable speed
switch. To switch the tool off when in continuous
operation, press the variable speed switch once
more and release it.
u Based on the different applications, turn around
the speed dial (11) to control the maximum
speed.
Drilling in metal
Start drilling with slow speed and increase to full
power while applying rm pressure on the tool.
A smooth even ow of metal chips indicates the
proper drilling rate. Use a cutting lubricant when
drilling metals. The exceptions are cast iron and
brass which should be drilled dry.
NOTE: Large [5/16" (8 mm) to 1/2" (13 mm)] holes
in steel can be made easier if a pilot hole [5/32"
(4 mm) to 3/16" (5 mm)] is drilled rst.
Drilling in wood
Start drilling with slow speed and increase to full
power while applying rm pressure on the tool.
Holes in wood can be made with the same twist
drills used for metal. These bits may overheat
unless pulled out frequently to clear chips from the
utes. Work that is apt to splinter should be
backed up with a block of wood.
Drilling in masonry
When drilling in masonry, use carbide-tipped bits
rated for Impact drilling and be certain that
the bits are sharp. Use a constant and rm force
on the tool to drill most effectively. A smooth, even
ow of dust indicates the proper drilling rate.
Screwdriving
u Select forward or reverse rotation.
Impact drilling (g. A)
u Select the Impact mode.
u Press the switch (1).
Rotary drilling (g. A)
u Select the rotary drilling mode.
u Proceed as described for Impact drilling.
Consult your dealer for further information on the
appropriate accessories.
Accessories
The performance of an electric tool depends on
its accessories. Stanleyaccessories are designed
according to high quality standards, to enhance
the performance of electric tool. The use of these
accessories can help you conveniently operate the
tool.
Maintenance
The Stanleycord / cordless appliance / tools are of
sophisticated design, can be used for a long time,
and only little maintenance is needed. To obtain
consistent satisfactory use, proper maintenance
and regular cleaning of the tools are necessary.
Warning! Before performing any maintenance
work on the cord / cordless electric tools, the fol-
lowing points must be implemented:
u Switch off the power of the equipment / tools
and pull off the plug;
u If the equipment / tools are equipped with inde-
pendent battery pack, please turn off the power
and remove the battery pack from the equip-
ment / tools.
u If the equipment / tools are equipped with an
integrated battery, please run out the battery,
before turning off its power.
u Before the cleaning, unplug the charger plug
from the power source. In addition, except
the regular cleaning on your charger, no other
maintenance is needed.
u Regularly use the soft brush or dry cloth to
clean the ventilation slot of the equipment /
tools / charger.
u Regularly use a damp cloth to clean the motor
housing. Please do not use any abrasive clean-
ing agents or solvent-based cleansing agents.
u Regularly open the clamping chuck and tap it
gently to remove any internal dust (after instal-
lation).
Cleaning
Warning! Once the visible dust build-up
is found at and/or around the ventilat-
ing ports, immediately ush the dust and
powder within the host shell with clean dry
air. To perform this procedure, wear the
approved safety equipment and dust mask.
9
ENGLISH
Warning! It is strictly forbidden to clean
the non-metallic parts of the tool with the
solvents or other irritant chemicals. These
chemicals may weaken the materials of
these components. Use a cloth moistened
with a mild soapy water to clean it. Do not
let any substance permeate into the tool
and.do not immerse any part of the tool
into a liquid.
Protect the environment
Separate collection. This product may not
be disposed together with the ordinary
household waste.
If you nd that your Stanleyproducts are needed to
be replaced or you will no longer need to use these
products, please do not put them together with the
household waste. Please place them separately to
recycle.
Separate collection of the used products
and packaging materials allow the
materials to be recycled and reused.
Reuse of the recycled materials helps to prevent
the pollution of the environment, and reduces the
demand for raw materials. Local regulations may
provide separate collection of the electrical
products from the household, at the municipal
waste sites or by the retailer when you purchase a
new product.
Service Information
Stanley offers a full network of company-owned
and authorized service locations throughout Asia.
All Stanley Service Centers are staffed with trained
personnel to provide customers with efcient and
reliable power tool service.Whether you need tech-
nical advice, repair, or genuine factory replacement
parts, contact the Stanley location nearest to you.
Notes
u Stanley’s policy is one of continuous
improvement to our products and, as such, we
reserve the right tochange product
specications without prior notice.
u Standard equipment and accessories may vary
by country.
u Product specications may differ by country.
u Complete product range may not be available in
all countries. Contact your local Stanley dealers
for range availability.
10
Stanley
@
/
1.
a.
b.
STDH7213
-B1 -XD -TW -KR
V 220-240 220-240 110 220
Hz 50/60 50/60 60 60
W 720
/min 0-3000 (0-2900 TW)
IPM 54000 (52200 TW)
/
mm 1.5-13
mm
- 16
- 13
- 32
kg 2.5
c.
2.
a.
b.
c.
d.
e.
f.
(RCD) RCD
3.
a.
b.
c. /
d.
e.
STDH7213
13mm
11
f.
g.
4.
a.
b.
c.
/
d.
e.
f.
g.
5.
a.
@
u
u
u
u
u
u
u
u
/
u
u
12
u
/
u
u
u
u
(MDF)
A
(13)
2014 XX JN
u
STANLEY
1.5 mm
2
( mm
2
)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
(m)
7.5 15 25 30 45 60
115 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
1
1
1
1
1
u
u
A
1
2
3 /
4
5
6
7
8
9
10
11
13
B
b
q
u
(4)
A
u
(9)
u
(10)
u
A
(6)
u
u
u
u
C
u
u
(6)
u
(7)
u
u
/ A
u
/
(3)
D
u
u
(12)
u
u
u
u
u
u
u
u
(RCD) RCD
u
u
AE
14
(6)
u
(1)
u
(2)
u
u
(11)
[5/32" (4 mm) 3/16"
(5 mm)] [5/16" (8 mm) 1/2"
(13 mm)]
u
A
u
u
(1)
A
u
u
Stanley
Stanley //
/
u
/
u
/
/
u
/
u
u
//
u
u
15
/
Stanley
Stanley
Stanley
Stanley
u
Stanley
u
/
u
u
/
Stanley
137
02-29994633
16
,
.
.
@
!
.
, /
.
. " "
( )
( ) .
1.
a. .
.
b. ,
.
STDH7213
-B1 -XD -TW -KR
V 220-240 220-240 110 220
Hz 50/60 50/60 60 60
W 720
/ 0-3000 (0-2900 TW)
IPM 54000 ( 52200 TW)
/
mm 1.5-13
mm
- 16
- 13
- 32
kg 2.5
c.
.
.
2.
a.
.
. ( )
.
.
b. , ,
.
,
.
c.
.
.
d. .
. , ,
.
e.
.
.
f.
(RCD)
. RCD
.
3.
a.
.
, ,
.
.
b. .
. ,
,
.
c. . /
STDH7213
13mm
17
.
.
d.
.
.
e. .
.
.
f. .
. ,
. ,
.
g.
,
.
.
4.
a. .
.
.
b. /
.
.
c.
/
.
.
d.
,
.
.
e. .
,
.
.
.
f.
.
.
g. ,
,
.
.
5.
a.
.
.
@
!
u
.
.
u ( )
.
.
u
.
" "
"
"
.
u
.
.
u ,
.
u
.
u ,
( )
.
.
.
u
.
.
18
u ,
( )
.
.
u
.
.
,
.
.
.
u .
u , .
u .
.
u .
u
(: , ,
MDF ).
.
!
.
( A)
(13) ,
.
: 2014 XX JN
, .
.
u ,
.
(
). 1.5 mm2.
.
.
( mm
2
)
()
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
(m)
7.5 15 25 30 45 60
()
110 0 - 2.0 6 6 6 6 6 10
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
.
1
1
1
1
1
u ,
.
u
.
( A)
1
2
3 /
4
5
6
7
8
9
10
11
!
19
.
( B)
.
b
:
,
q
:
.
u (4)
.
( A)
u (9)
.
u (10)
.
u .
( A)
(6)
.
.
u .
u ,
.
u ,
.
u
.
( C)
u .
u (6) .
u (7)
.
u .
u .
/ ( A)
u / /
(3) ( ).
.
( D)
u ( 3 ) .
u (12)
.
u
.
u
.
u .
u .
.
u
.
.
u
. .
u
.
" "
" "
.
u
(RCD)
. RCD
.
u .
u .
( A, E)
: ,
.
: ,
.
(6) .
/
u (1)
.
.
u (2)
.
.
u
.
.
u (11)
20
.
.
.
.
.
: [5/32"(4 mm) to 3/16" (5 mm)]
[5/16" (8 mm) ~ 1/2" (13 mm)]
.
.
.
.
.
,
.
.
.
u .
( A)
u .
u (1) .
( A)
u .
u .
.
.
.
/ /
,
. ,
.
! /
, .
u / ,
u /
, /
.
u / ,
.
u
. ,
.
u /
/
.
u
.
.
u
.
!
,
. ,
.
!
.
.
.
.
.
.
,
. .
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
