Hilti SF 10W-A22 ATC Cordless Drill Driver ユーザーマニュアル

SF 10WA22

English 1

Français 12

Dansk 24

Svenska 36

Norsk 47

Suomi 59

Eesti 70

Latviešu 82

Lietuvių 94

Русский 106

Українська 120

Қазақ 134

Türkçe 147

ﻋﺮﺑﻲ 159

日本語 172

한국어 183

繁體中文 194

中文 205

1

2

3

4

5

SF 10WA22

en Originaloperatinginstructions....................................... 1

fr Noticed'utilisationoriginale ....................................... 12

da Originalbrugsanvisning .......................................... 24

sv Originalbruksanvisning........................................... 36

no Originalbruksanvisning .......................................... 47

fi Alkuperäisetohjeet ............................................. 59

et Originaalkasutusjuhend .......................................... 70

lv Oriģinālālietošanasinstrukcija ..................................... 82

lt Originalinaudojimoinstrukcija...................................... 94

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 106

uk Оригінальна інструкція з експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

tr Orijinalkullanımkılavuzu ......................................... 147

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 159

ja オリジナル取扱説明書 ............................................ 172

ko 오리지널사용설명서............................................. 183

zh 原始操作說明.................................................. 194

cn 原版操作说明译文 ............................................... 205

*2130487* 2130487 English 1

Original operating instructions

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

2 English 2130487 *2130487*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

Rated speed under no load

Revolutions per minute

Active Torque Control (ATC)

Direct current (DC)

Li-ion battery

The power tool supports near-field communication (NFC) technology, which is compatible with

iOS and Android platforms.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

1.4 Product information

Hilti products are designed for professional use and may be operated, serviced and maintained only by

trained, authorized personnel. This personnel must be specifically informed about the possible hazards. The

product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used

not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Drill/driver SF 10WA22

Generation 02

Serial no.

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

*2130487* 2130487 English 3

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

4 English 2130487 *2130487*

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Drill safety warnings

Safety instructions for all operations

▶Use the auxiliary handle(s). Loss of control can cause personal injury.

▶Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory or fasteners may contact hidden wiring. Cutting accessory or fasteners contacting

a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an

electric shock.

Safety instructions when using long drill bits

▶Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds,

the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal

injury.

▶Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher

speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in

personal injury.

▶Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend

causing breakage or loss of control, resulting in personal injury.

2.3 Additional safety precautions for screwdrivers

▶Use the product and accessories only when they are in perfect working order.

▶Never tamper with or modify the product or accessories in any way.

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the product could give you an electric shock or cause an explosion if you

accidentally damage an electric cable or a gas or water pipe.

▶Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some

examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone

and other products containing silicates; certain types of wood, such as oak, beech and chemically

treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and

bystanders by means of the hazard classification of the materials to be worked. Implement the necessary

measures to restrict exposure to a safe level, for example by the use of a dust collection system or by

the wearing of suitable respiratory protection. The general measures for reducing exposure include:

▶working in an area that is well ventilated,

▶avoidance of prolonged contact with dust,

▶directing dust away from the face and body,

▶wearing protective clothing and washing exposed areas of the skin with water and soap.

*2130487* 2130487 English 5

▶Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed

accessories are secure.

▶Do not use blunted bits.

▶Use large, heavy accessory tools only with the power tool set to first gear. There is otherwise a risk of

causing damage to the power tool when switching it off or, under unfavorable circumstances, the chuck

may work loose.

▶Use auxiliary handles supplied with the product. Loss of control can cause personal injury. Make sure

that the auxiliary handle is firmly seated and securely installed.

▶Switch the product on only after you have brought it to the working position.

▶Secure the workpiece. Use clamps or a vice to hold the workpiece in position. The workpiece is thus

held more securely than by hand and both hands remain free to operate the power tool.

▶Always hold the product with both hands on the grips provided. Keep the grips clean and dry.

▶Keep the air vents clear at all times. Risk of burn injuries due to blocked air vents!

▶Do not touch rotating parts – risk of injury!

▶Wear eye protection, a hard hat and ear protection and suitable respiratory protection while the product

is in use.

▶Wear eye protection. Flying fragments can injure the body and eyes.

▶Do not look directly into the light source (LED) of the product and do not aim the beam at other persons’

faces. Risk of dazzling or eye damage.

▶Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

▶Wait until the product has come to a complete stop before you lay it down.

▶Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in

cuts and burns.

2.4 Battery use and care

▶Comply with the following safety instructions for the safe handling and use of Li-ion batteries.

Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.

▶Use only batteries that are in perfect working order.

▶Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely

harmful to health!

▶Do not under any circumstances modify or tamper with batteries!

▶Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C

(176 °F).

▶Never use or charge a battery that has suffered an impact or been damaged in any other way. Check

your batteries regularly for signs of damage.

▶Never use recycled or repaired batteries.

▶Never use the battery or a battery-operated power tool as a striking tool.

▶Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This

can lead to explosions.

▶Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.

This can damage the battery and also cause material damage and personal injury.

▶Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,

electric shock, burns, fire and explosions.

▶Use only chargers and power tools approved for the specific battery type. Read and follow the relevant

operating instructions.

▶Do not use or store the battery in explosive environments.

▶If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible

and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to

cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the

document entitled "Instructions on safety and use for Hilti Li-ion batteries".

Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.

→ page 10

Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning

the QR code at the end of these operating instructions.

6 English 2130487 *2130487*

3 Description

3.1 Overview of the product 1

@Side handle

;Keyless chuck

=Torque and drilling mode selector ring

%Gear selector switch

&Forward/reverse switch with switch-on inter-

lock

(Control switch (with electronic speed control)

)Grip

+Light to illuminate the work area

§Belt hook (optional)

/Liion battery

:Battery release button

∙State of charge and fault display (Li-ion bat-

tery)

3.2 Intended use

The product described is a hand-held cordless drill/driver. It is designed for driving and removing screws

and for drilling in steel, wood and plastic.

• Use only Hilti lithiumion batteries of the B 22 series with this product.

• Use only Hilti-approved battery chargers to charge these batteries. More information is available from

your Hilti Store or from www.hilti.group

3.3 ATC

The product is equipped with the ATC (Active Torque Control) quick-acting electronic cut-out.

If the accessory tool sticks or stalls, the product will suddenly pivot about its own axis in the opposite direction.

ATC detects this sudden pivoting movement of the product and switches the product off immediately.

For ATC to function correctly, the product must be free to pivot.

After an ATC cut-out, switch the product off and then on again.

3.4 Liion battery display

The charge status of the Li-ion battery and malfunctions of the power tool are indicated by the display on

the Liion battery. The charge status of the Liion battery is displayed after pressing one of the two battery

release buttons.

Status Meaning

4 LEDs light. Charge status: 75 % to 100 %

3 LEDs light. Charge status: 50 % to 75 %

2 LEDs light. Charge status: 25 % to 50 %

1 LED lights. Charge status: 10 % to 25 %

1 LED blinks, the power tool is ready for use. Charge status: < 10 %

1 LED blinks, the power tool is not ready for use. The battery has overheated or is completely dis-

charged.

4 LEDs blink, the power tool is not ready for use. The power tool is overloaded or has overheated.

*2130487* 2130487 English 7

Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch.

If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.

3.5 Items supplied

Drill / driver, side handle, operating instructions

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group

4 Technical data

4.1 Drill/driver

Rated voltage 21.6 V

Weight in accordance with EPTA Procedure 01 including B22⁄8.0 battery 3.3 kg

Speed 1st gear 0 /min … 310 /min

2nd gear 0 /min … 530 /min

3rd gear 0 /min … 1,210 /min

4th gear 0 /min … 2,100 /min

Torque range (15 settings) 2 Nm … 12 Nm

Ø drill bit (softwood) 1.5 mm … 50 mm

Ø drill bit (hardwood) 1.5 mm … 20 mm

Ø drill bit (metal) 1.5 mm … 13 mm

4.2 Battery

Battery operating voltage 21.6 V

Ambient temperature −10 ℃ … 60 ℃

Storage temperature −20 ℃ … 40 ℃

Battery charging starting temperature −10 ℃ … 45 ℃

4.3 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

An accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the total

working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise emission values

SF 10W-A22

Emission sound pressure level (LpA)75 dB(A)

Uncertainty for the sound pressure level (KpA)3 dB(A)

Sound (power) level (LWA)86 dB(A)

Uncertainty for the sound power level (KWA)3 dB(A)

8 English 2130487 *2130487*

Total vibration

SF 10W-A22

Vibration emission value for screwdriving (ah)< 2.5 m/s²

Uncertainty for screwdriving (K) 1.5 m/s²

Drilling in metal (ah,D)< 2.5 m/s²

Uncertainty for drilling in metal (K) 1.5 m/s²

5 Preparations at the workplace

WARNING

Risk of injury by inadvertent starting!

▶Before inserting the battery, make sure that the product is switched off.

▶Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1 Inserting the battery

WARNING

Risk of injury by short circuit or falling battery!

▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the product until it engages with an audible click.

3. Check that the battery is seated securely.

5.2 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the tool.

5.3 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery. → page 6

5.4 Fitting the side handle 2

CAUTION

Risk of injury by accidental starting!

▶Make sure that the forward / reverse switch is in the middle position (switch-on interlock engaged) or that

the battery has been removed from the drill / driver.

▶Fit the side handle.

5.5 Adjusting the side handle 3

▶Adjust the side handle to the desired position.

5.6 Fitting the accessory tool

1. Set the forward/reverse switch to the middle position or remove the battery from the power tool.

2. Check that the connection end of the accessory tool is clean. Clean the connection end if necessary.

3. Open the keyless chuck.

4. Insert the accessory tool in the keyless chuck and then turn the chuck firmly by hand until tight and

several clicks are heard.

*2130487* 2130487 English 9

5. Check that the accessory tool is held securely.

5.7 Removing the accessory tool

1. Set the forward/reverse switch to the middle position or remove the battery from the power tool.

2. Open the keyless chuck.

3. Pull the accessory tool out of the keyless chuck.

5.8 Fall arrest

WARNING

Risk of injury by falling tool and/or accessory!

▶Use only the Hilti tool tether recommended for your product.

▶Prior to each use, always check the attachment point of the tool tether for possible damage.

▶Do not secure a tool tether to the belt hook. Do not use a belt hook to lift the product.

Comply with the national regulations for working at heights.

As drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether

#2261970.

▶Secure the retaining strap to the installation openings for accessories. Check that it holds securely.

▶Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a

load-bearing structure. Check that both carabiners hold securely.

Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.

6 Types of work

CAUTION

Risk of damage by incorrect handling!

▶Do not operate the switches for direction of rotation and/or function selection during operation.

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Setting forward or reverse rotation 4

An interlock prevents switching while the motor is running.

The control switch is locked when the forward/reverse switch is in the middle position (switch-on

interlock).

▶Set the forward/reverse switch to the desired direction of rotation.

6.2 Selecting the gear 5

▶Select the desired gear by adjusting the two gear selector switches.

6.3 Switching on

▶Press the control switch.

The running speed can be controlled smoothly right up to maximum speed by varying how far the

control switch is pressed in.

6.4 Drilling

1. Set the torque and operating mode selector ring to the symbol.

2. Set the forward/reverse switch to the “forward” position.

10 English 2130487 *2130487*

6.5 Screwdriving

1. Set the torque and operating mode selector ring to the required torque.

2. Set the forward/reverse switch to the desired direction of rotation.

6.6 Switching off

▶Release the control switch.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily

on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents

containing silicone as these can attack the plastic parts.

Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product

repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full

working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with your product can be found at your

Hilti Store or online at: www.hilti.group

8 Transport and storage of cordless tools and batteries

Transport

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

*2130487* 2130487 English 11

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

Trouble or fault Possible cause Action to be taken

Product does not work. The battery is not fully inserted. ▶Push the battery in until it

engages with an audible double

click.

Battery is discharged. ▶Change the battery and charge

the empty battery.

Product does not work and all

four LEDs flash. Product momentarily overloaded. ▶Release the control switch and

then press it again.

The overheating cut-out has been

activated.

▶Allow the product to cool down.

Clean the air vents.

Product does not work and

one LED flashes. Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Bring the battery to the recom-

mended operating temperature.

The on/off button cannot be

pressed, i.e. the button is

locked.

The forward/reverse selector

switch is in the middle position.

▶Push the forward/reverse switch

to the left or right.

The battery runs down more

quickly than usual. Very low ambient temperature. ▶Allow the battery to warm up

slowly to room temperature.

The battery doesn’t engage

with an audible double click. The retaining lugs on the battery

are dirty.

▶Clean the retaining lugs and

push the battery in until it

engages. Contact Hilti Service

if the problem persists.

The product or battery gets

very hot. The product is overloaded (appli-

cation limits exceeded).

▶Pay attention to the power

and performance rating of the

product before using it, i.e

check its suitability for the job

on hand. See “Technical data”

section.

12 Français 2130487 *2130487*

10 Disposal

WARNING

Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

▶DO NOT send batteries through the mail!

▶Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶Dispose of your battery out of the reach of children.

▶Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be

correctly separated before they can be recycled. In many countries, your old tools, machines or appliances

can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

12 Further information

For more information on operation, technology, environment and recycling, follow this link:

qr.hilti.com/manual/?id=2130485&id=2130487

This link is also to be found at the end of the operating instructions, in the form of a QR code.

Notice d'utilisation originale

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service. C'est la condition préalablement

requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la présente documentation ainsi que

celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement le transmettre à des tiers

avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés :

DANGER

DANGER !

▶Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶Pour un danger potentiel qui peut entraîner de graves blessures corporelles ou la mort.

*2130487* 2130487 Français 13

ATTENTION

ATTENTION !

▶Pour une situation potentiellement dangereuse pouvant entraîner des blessures corporelles ou des

dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Ces chiffres renvoient à l'illustration correspondante au début du présent mode d'emploi

La numérotation détermine la séquence des étapes de travail dans l'image et peut se différencier

de celles des étapes de travail dans le texte

Les numéros de position sont utilisés dans l'illustration Vue d’ensemble et renvoient aux numé-

ros des légendes dans la section Vue d'ensemble du produit

Ce signe doit inviter à manier le produit en faisant particulièrement attention.

1.3 Symboles spécifiques au produit

1.3.1 Symboles sur le produit

Les symboles suivants sont utilisés sur le produit :

Vitesse nominale à vide

Tours par minute

ATC (Active Torque Control : correcteur de couple actif)

Courant continu

Accu lithium-ions

L'appareil prend en charge la technologie NFC qui est compatible avec les plates-formes iOS et

Android.

Ne jamais utiliser l'accu comme outil de percussion.

Ne pas laisser tomber l'accu. Ne pas utiliser d'accu ayant subi un choc ou d'autres dommages.

1.4 Informations produit

Les produits Hilti sont destinés aux professionnels et ne doivent être utilisés, entretenus et réparés que par

un personnel autorisé et formé. Ce personnel doit être au courant des dangers inhérents à l'utilisation de

l'appareil. Le produit et ses accessoires peuvent s'avérer dangereux s'ils sont utilisés de manière incorrecte

par un personnel non qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque signalétique.

14 Français 2130487 *2130487*

▶Inscrivez le numéro de série dans le tableau suivant. Les informations produit vous sont demandées

lorsque vous contactez nos revendeurs ou services après-vente.

Caractéristiques produit

Visseuse-perceuse SF 10WA22

Génération 02

N° de série

1.5 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit décrit ici est conforme aux

directives et normes en vigueur. Une copie de la Déclaration de conformité se trouve en fin de la présente

documentation.

Pour obtenir les documentations techniques, s'adresser à :

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sécurité

2.1 Indications générales de sécurité pour les appareils électriques

AVERTISSEMENT Lire toutes les consignes de sécurité et instructions, illustrations et caractéris-

tiques techniques, qui accompagnent cet outil électroportatif. Tout manquement à l'observation des

instructions suivantes risque de provoquer une électrocution, un incendie et/ou de graves blessures.

Les consignes de sécurité et instructions doivent être intégralement conservées pour les utilisations

futures.

La notion d'« outil électroportatif » mentionnée dans les consignes de sécurité se rapporte à des outils

électriques raccordés au secteur (avec câble d'alimentation) et à des outils électriques sur accu (sans câble

d'alimentation).

Sécurité sur le lieu de travail

▶Conserver la zone de travail propre et bien éclairée. Un lieu de travail en désordre ou mal éclairé

augmente le risque d'accidents.

▶Ne pas faire fonctionner les outils électriques en atmosphère explosive et où se trouvent des

liquides, des gaz ou poussières inflammables. Les outils électriques produisent des étincelles qui

peuvent enflammer les poussières ou les fumées.

▶Maintenir les enfants et les personnes présentes à l'écart pendant l'utilisation de l'outil électro-

portatif. En cas d'inattention il y a risque de perdre le contrôle de l'appareil.

Sécurité relative au système électrique

▶La fiche de secteur de l'outil électroportatif doit être adaptée à la prise de courant. Ne jamais

modifier la fiche de quelque façon que ce soit. Ne pas utiliser d'adaptateurs avec des outils

électriques à branchement de terre. Des fiches non modifiées et des prises de courant adaptées

réduiront le risque de choc électrique.

▶Éviter le contact physique avec des surfaces mises à la terre tels que tuyaux, radiateurs, cuisinières

et réfrigérateurs. Il y a un risque élevé de choc électrique au cas où votre corps serait relié à la terre.

▶Ne pas exposer les outils électroportatifs à la pluie ou à l'humidité. La pénétration d'eau à l'intérieur

d'un outil électroportatif augmentera le risque d'un choc électrique.

▶Ne jamais utiliser le câble de raccordement à d'autres fins que celles prévues, telles que pour

porter, accrocher ou débrancher l'outil électroportatif de la prise de courant. Maintenir le câble

de raccordement à l'écart de la chaleur, des parties grasses, des bords tranchants ou des parties

en mouvement. Des câbles de raccordement endommagés ou emmêlés augmentent le risque de choc

électrique.

▶Si l'outil électroportatif est utilisé à l'extérieur, utiliser uniquement des câbles de rallonge

homologués pour les applications extérieures. L’utilisation d’un câble de rallonge homologué

pour les applications extérieures réduit le risque d’un choc électrique.

▶Si l'utilisation de l'outil électrique dans un environnement humide ne peut pas être évitée, utiliser

un interrupteur de protection contre les courants de court-circuit. L'utilisation d'un tel interrupteur

de protection réduit le risque d'une décharge électrique.

Sécurité des personnes

▶Rester vigilant, surveiller ce que l'on fait. Faire preuve de bon sens en utilisant l'outil électroportatif.

Ne pas utiliser l'outil électroportatif en étant fatigué ou sous l'emprise de l'alcool, de drogues ou

*2130487* 2130487 Français 15

de médicaments. Un moment d'inattention lors de l'utilisation de l'outil électroportatif peut entraîner

des blessures graves.

▶Utiliser un équipement de protection personnel et toujours porter une protection pour les

yeux. Les équipements de protection personnels tels que masque antipoussière, chaussures de

sécurité antidérapantes, casque de protection ou protection acoustique suivant l'utilisation de l'outil

électroportatif, réduiront le risque de blessures des personnes.

▶Éviter une mise en service par mégarde. S'assurer que l'outil électroportatif est arrêté avant de le

brancher à la source de courant et/ou à l'accu, de le prendre ou de le porter. Le fait de porter l'outil

électroportatif avec le doigt sur l'interrupteur ou de brancher l'appareil sur la source de courant lorsque

l'interrupteur est en position de fonctionnement peut entraîner des accidents.

▶Retirer tout outil de réglage ou toute clé avant de mettre l'outil électroportatif en fonctionnement.

Une clé ou un outil se trouvant sur une partie en rotation peut causer des blessures.

▶Adopter une bonne posture. Veiller à toujours garder une position stable et équilibrée. Cela permet

un meilleur contrôle de l'outil électroportatif dans des situations inattendues.

▶S'habiller de manière adaptée. Ne pas porter de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à distance des parties en mouvement. Des vêtements amples,

des bijoux ou des cheveux longs peuvent être happés par des parties en mouvement.

▶Si des dispositifs servant à aspirer ou à recueillir les poussières doivent être utilisés, s'assurer

qu'ils sont effectivement raccordés et correctement utilisés. L'utilisation d'un dispositif d'aspiration

de la poussière peut réduire les risques dus aux poussières.

▶Ne pas sous-estimer les mesures de sécurité à prendre et ne pas ignorer sciemment les règles

de sécurité applicables aux outils électriques, même si l'on est utilisateur chevronné après de

fréquentes utilisations de l'outil électroportatif. Un manque d'attention peut conduire à de graves

blessures en quelques fractions de seconde.

Utilisation et maniement de l'outil électroportatif

▶Ne pas forcer l'appareil. Utiliser l'outil électroportatif adapté au travail à effectuer. Un outil

électroportatif approprié réalisera mieux le travail et de manière plus sûre au régime pour lequel il a été

conçu.

▶Ne pas utiliser d'outil électroportatif dont l'interrupteur est défectueux. Tout outil électroportatif qui

ne peut plus être mis en ou hors fonctionnement est dangereux et doit être réparé.

▶Débrancher la fiche de la prise de courant et/ou l'accu amovible avant d'effectuer des réglages sur

l'appareil, de changer les accessoires, ou de ranger l'appareil. Cette mesure de précaution empêche

une mise en fonctionnement par mégarde de l'outil électroportatif.

▶Conserver les outils électroportatifs non utilisés hors de portée des enfants. Ne permettre

l'utilisation de l'appareil à aucune personne qui ne soit pas familiarisée avec celui-ci ou qui n'a

pas lu ces instructions. Les outils électroportatifs sont dangereux lorsqu'ils sont entre les mains de

personnes non initiées.

▶Prendre soin des outils électroportatifs et des accessoires. Vérifier que les parties en mouvement

fonctionnent correctement et qu'elles ne sont pas coincées, et contrôler si des parties sont

cassées ou endommagées de sorte que le bon fonctionnement de l'outil électroportatif s'en trouve

entravé. Faire réparer les parties endommagées avant d'utiliser l'appareil. De nombreux accidents

sont dus à des outils électroportatifs mal entretenus.

▶Garder les outils de coupe affûtés et propres. Des outils destinés à couper correctement entretenus

avec des arêtes de coupe tranchantes sont moins susceptibles de bloquer et sont plus faciles à contrôler.

▶L'outil électroportatif, les accessoires, les outils amovibles, etc. doivent être utilisés conformément

à ces instructions. Tenir également compte des conditions de travail et du travail à réaliser.

L'utilisation des outils électroportatifs à d'autres fins que celles prévues peut entraîner des situations

dangereuses.

▶Veiller à ce que les poignées et surfaces de préhension soient toujours être sèches, propres et

exemptes de traces de graisse ou d'huile. Avec des poignées et surfaces de préhension glissantes, la

sécurité et le contrôle de l'outil électroportatif ne peuvent être assurés dans des situations inopinées.

Utilisation et maniement de l'outil sur accu

▶Ne charger les accus que dans des chargeurs recommandés par le fabricant. Si un chargeur

approprié à un type spécifique d'accus est utilisé avec des accus non recommandés pour celui-ci, il y a

risque d'incendie.

▶Dans les outils électroportatifs, utiliser uniquement les accus spécialement prévus pour ceux-ci.

L'utilisation de tout autre accu peut entraîner des blessures et des risques d'incendie.

▶Tenir l'accu non utilisé à l'écart de tous objets métalliques tels qu'agrafes, pièces de monnaie, clés,

clous, vis ou autres, étant donné qu'un pontage peut provoquer un court-circuit. Un court-circuit

entre les contacts d'accu peut provoquer des brûlures ou un incendie.

16 Français 2130487 *2130487*

▶En cas d'utilisation abusive, du liquide peut sortir de l'accu. Éviter tout contact avec ce liquide. En

cas de contact par mégarde, rincer soigneusement avec de l'eau. Au cas où le liquide rentrerait

dans les yeux, consulter en plus un médecin. Le liquide qui sort de l'accu peut entraîner des irritations

de la peau ou causer des brûlures.

▶Ne pas utiliser d'accu endommagé ou modifié. Des accus endommagés ou modifiés peuvent avoir

un comportement imprévisible et provoquer un incendie, une explosion ou engendrer un risque de

blessures.

▶Ne jamais exposer l'accu au feu ou à des températures trop élevées. Le feu ou des températures

supérieures à 130 °C (265 °F) peuvent provoquer une explosion.

▶Suivre toutes les instructions de charge et ne jamais charger l'accu ou l'outil sur accu hors de la

plage de températures spécifiée dans le manuel d'utilisation. Une charge inappropriée ou hors de la

plage de températures spécifiée risque d'endommager l'accu et accroître le risque d'incendie.

Service

▶L'outil électroportatif doit uniquement être réparé par un personnel qualifié et seulement avec des

pièces de rechange d'origine. Ceci permet d'assurer la sécurité de l'appareil.

▶Ne jamais entretenir d'accus endommagés. Toutes les opérations d'entretien sur des accus doivent

exclusivement être réalisées par le fabricant ou un prestataire de service client agréé.

2.2 Indications de sécurité pour les perceuses

Consignes de sécurité pour tous les travaux

▶Utiliser la poignée supplémentaire. La perte de contrôle peut entraîner des blessures.

▶Tenir l’outil électroportatif par les surfaces isolées des poignées lors des travaux pendant lesquels

l'outil amovible ou les vis risquent de toucher des câbles électriques cachés. Le contact avec un

câble sous tension risque de mettre les parties métalliques de l’appareil sous tension et de provoquer

une décharge électrique.

Consignes de sécurité lors de l'utilisation de la mèche longue

▶Ne jamais travailler avec une vitesse de rotation plus élevée que la vitesse de rotation maximale

autorisée pour la mèche. En cas de vitesse de rotation plus élevée, la mèche risque de se déformer

légèrement si elle peut tourner librement sans contact avec la pièce travaillée et entraîner des blessures.

▶Toujours commencer l'opération de perçage à vitesse réduite et alors que la mèche est en contact

avec la pièce travaillée. En cas de vitesse de rotation plus élevée, la mèche risque de se déformer

légèrement si elle peut tourner librement sans contact avec la pièce travaillée et entraîner des blessures.

▶Ne pas exercer de pression excessive et seulement dans le sens longitudinal. Les mèches peuvent

se tordre et donc se casser, ou il peut y avoir perte de contrôle de l'appareil ce qui entraîne un risque de

blessures.

2.3 Consignes de sécurité supplémentaires spécifiques à la visseuse

▶Utiliser le produit et les accessoires uniquement s'ils sont en parfait état.

▶Ne jamais entreprendre de manipulation ni de modification sur le produit ou les accessoires.

▶Avant d'entamer le travail, vérifier qu'il n'y a pas de câbles ou gaines électriques, tuyaux de gaz ou d’eau

cachés dans la zone d'intervention. Les parties métalliques externes du produit peuvent provoquer un

choc électrique ou une explosion si vous endommagez une ligne électrique, une conduite de gaz ou une

conduite d'eau.

▶La poussière générée par le meulage, le ponçage, le tronçonnage et le forage peut contenir des produits

chimiques dangereux. Par exemple : plomb ou peinture à base de plomb ; brique, béton et autres

produits de maçonnerie, pierre naturelle et autres produits contenant des silicates ; certains bois, tels

que le chêne, le hêtre et le bois traité chimiquement ; amiante ou matériaux contenant de l'amiante.

Déterminer l'exposition de l'opérateur et personnes se trouvant dans l'entourage en fonction de la classe

de danger des matériaux traités. Prendre les mesures nécessaires pour maintenir l'exposition à un

niveau sûr, par exemple en utilisant un système de collecte des poussières ou en portant une protection

respiratoire appropriée. Mesures générales visant à réduire l'exposition :

▶Travailler dans un endroit bien ventilé

▶Éviter le contact prolongé avec la poussière

▶Faire en sorte que la poussière soit dirigée loin du visage et du corps

▶Porter des vêtements de protection et laver les zones exposées à l'eau et au savon

▶Risque de blessures dues à la chute d'outils et/ou d'accessoires. Avant de commencer à travailler,

contrôler si l'accu et l'accessoire monté sont solidement fixés.

▶Ne pas utiliser d'embouts émoussés.

ページが読み込まれています...

Hilti SF 10W-A22 ATC Cordless Drill Driver ユーザーマニュアル

Hilti SF 10W-A22 ATC Cordless Drill Driver ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント