Kyosho F-86F SABRE ユーザーマニュアル

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

No. 11086

INDEX

WINGSPAN: 1000mm

SAFETY PRECAUTIONS

This radio control model is not a toy!

First-time builders should seek the advice of experienced modellers

before commencing assembly and if they do not fully understand

any part of the construction.

Assemble this kit only in places out of children’s reach!

Take enough safety precautions prior to operating this model.

You are responsible for this model’s assembly and safe operation!

Always keep this instruction manual ready at hand for quick

reference, even after completing the assembly.

For Advanced Flyers.

THE FINEST RADIO CONTROL MODELS

R

INSTRUCTION MANUAL

2

3~14

15

16

REQUIRED FOR OPERATION

BEFORE YOU BEGIN

ASSEMBLY

SPARE PARTS

OPERATING YOUR MODEL SAFELY

RADIO CONTROLLED .15 ENGINE POWERED

DUCTED FAN AIRCRAFT

Before commencing assembly, please read these instructions thoroughly!

1

4

A minimum 4 channel transmitter,

configured for aircraft.

Ensure you read and understand the instructions included with your radio.

Sharp Hobby Knife

Phillips Screwdriver (L, M, S)

Phillips Screwdriver (s)

Drill

Needle Nose Pliers

Awl

Scissors

File (round)

3 12

12 AA-size Batteries

AAAA

Wire Cutters

Required for engine starting:

Fuel Bottle

Plug Wrench

1 x Extension Lead

2

No.73801

Glow engine fuel only.

MOD

EL

ENGIN

E

FUEL

3

Epoxy A

Epoxy B

Instant Glue

(30 )

Epoxy Glue (30 minutes type)

Glue

CAUTION

:

For details concerning the equipment listed below

(size, maker, etc.), check with your hobby shop.

CAUTION

:

Only use a minimum 4 channel transmitter, configured

for aircraft!

(No other radio may be used!)

WARNING: Normal gasoline

cannot be used

with glow engines.

Other equipment for enhancing airplane operation & performance

Fuel Filter

5

4

Others

Silicone Tube

Vibration Protection Sponge

x 4

A 4 Channel radio with 4 mini servos is required.

1

Read through the manual before you begin, so you will have an overall idea of what to do.

Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.

2

3

Symbols used throughout this instruction manual, comprise:

Apply epoxy glue.

Assemble left and right sides

the same way.

Must be purchased

separately!

2mm

Drill holes with the specified

diameter (here: 2mm).

Cut off shaded portion.

2mm

Cut off excess.

Apply instant glue

(CA glue, super glue).

Ensure smooth non-binding

movement while assembling.

Do not overlook this symbol!

low setting

Use an iron covered with a cloth!

Start at low setting. Increase the set--

ting if necessary. If it is too high, you

may damage the film.

with cover (cloth)

The pre-covered film on ARF kits may wrin-kle due to

variations of temperature. Smooth out as explained right.

Pay close attention here!

Warning!

One-touch Plug Heater Set

2

REQUIRED FOR OPERATION (Purchase separately!)

TOOLS REQUIRED (Purchase separately!)

BEFORE YOU BEGIN

3

1

3

2

Main Wing

Dihedral 32mm at wing tip.

Fill the gap with epoxy.

Do not disregard this symbol!

Warning!

Pay close attention here!

Apply epoxy glue.

Cut off shaded portion.

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(CA glue, super glue).

Assemble left and right sides

the same way.

32mm

Install the hinges completely

before applying instant glue.

Align the centre of the main

wing with the aileron.

Note the direction.

Top

Securely glue together. If it comes off

during flights, you may lose control of

your airplane, resulting in an accident !

Warning!

2

Horn Chip

Only cut the film.

Do not cut into the wood.

Only cut the film.

Do not cut into the wood.

Bottom Side

3.1

mm

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

32mm

4

6

5

Main Wing

Main Landing Gear

Do not disregard this symbol!

Warning!

Pay close attention here!

Apply epoxy glue.

Cut off shaded portion.

Assemble left and right sides

the same way.

Included with the

radio set.

Aileron Servo

5

mm

2

mm

If it comes off during flights, you may

lose control of your airplane, resulting

in an accident !

Warning!

8

TP Screw

2.6 x 8mm

2

3 x 4mm

Set Screw

2

Stopper

Collar

3 x 4mm

Stopper

Use the rest of wire in step .

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

ページが読み込まれています...

6

Apply epoxy glue.

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

11

10

Fuselage

Fuselage & Main wing

2

3 x 20mm

Screw

2

3mm

Washer

3mm

Blind Nut

3 x20mm

3mm

5

mm

Screw

Washer

3x 20mm

3mm

Blind Nut

4.5mm

12

3 x 14mm

TP Screw

TP

3 x 14mm

TP Screw

Enlarge holes with a file if it is needed.

4

The line is on the top.

Align it with the back

edge of the wing saddle.

4.5mm

70mm

6mm

Align with the

corner of engine

hatch.

Side view

These parts can not be reversed.

Cut the tip of pipe as illustrated to

allow smooth insertion.

7

Do not disregard this symbol!

Warning!

Pay close attention here!

Apply epoxy glue.

Cut off shaded portion.

Place PP pipe and aluminum

pipe in their correct positions

and glue trunk frame on the

fuselage.

Attach with epoxy all around

the perimeter.

Assemble in the specified order.

13

Back

Figures on the

picture are the

length of the PP

pipe coming out.

5

12

20

14

Cut PP pipe (thick) and aluminum

pipe as following length.

15

Engine

4

3 x 20mm

Cap screw

4

3mm

Washer

3mm

Spring Washer

4

3mm

Nylon Nut

3 x 20mm

3mm

Warning!

8

Pay close attention here!

Cut off shaded portion.

16

Engine

2.6 x 8mm

TP Screw

1

2.6 x 8mm

17

Engine Muffler

Position the muffler so that

the 3x5mm screw is 45 degrees

to the engine.

2.6 x 22mm

18

4

3 x 14mm

TP Screw

TP

1

3mm

Washer

3mm

Nylon Nut

3 x 15mm

1

Screw

3 x 15mm

3 x 14mm

5

mm

3mm

Drill a hole for engine slow speed

adjustment.

Use the rest of wire.

6

mm

10

mm

Drill holes with the specified

diameter (here: 2mm).

2mm

9

Do not disregard this symbol!

Warning!

Pay close attention here!

19

1

3 x 25mm

Cap Screw

1

7 mm

Washer

1

Drive Nut

Note the direction.

20

1

Nose Landing Gear Horn

3

1

3 x 4mm

Set Screw

4

Stopper

Collar

Nose Gear Horn

3 x 4mm

Stopper

21

Fuel Tank

1

3 x 25mm TP

TP Screw

5mm

After confirming

the direc-tion (see

front view of fuel

tank), insert and

tighten the screw.

Bend as shown

here.

12mm

3 x 25mm

Completed

Ensure smooth non-binding

movement while assembling.

Apply epoxy glue.

3 x 25mm

7mm

Warning!

Tighten the nut securely.

If it comes off during flights,

you may lose control of your

airplane, resulting in an accident !

3 x 4mm

Stopper

Collar

3mm

10

Do not disregard this symbol!

Warning!

Pay close attention here!

Cut off shaded portion.

22

Cut the velcro in half before installing.

Velcro

23

To the carburetor

3 x 10mm

1

3mm

Nylon Nut

3mm

Washer

Horn chip

24

Horizontal Tail

Install the hinges completely

before applying instant glue.

2

mm

17

mm

3

mm

2

Apply epoxy glue.

Assemble left and right sides

the same way.

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(CA glue, super glue).

Must be purchased separately!

7mm

10mm

View from the bottom

Horn Chip

Warning!

Drill holes with the specified

diameter (here: 2mm).

2mm

ページが読み込まれています...

12

30

29

Rudder Servo

Rudder Linkage

Apply epoxy glue.

Included with the radio set.

3 x 4mm

Set Screw

1

2mm

Washer

Nut

Linkage Stopper

1

2mm

Must be purchased separately!

28

Rudder Linkage

3 x 30mm

1

2

3mm

Nut

3mm

Washer

( L )

Horn chip ( L )

2

mm

3.1mm

2mm

3 x 4mm

2 x 6

Crimp this part with a pliers.

2 x 6

Assemble left and right sides

the same way.

Drill holes with the specified

diameter (here: 2mm).

2mm

13

31

32

Do not disregard this symbol!

Warning!

Pay close attention here!

Apply epoxy glue.

Cut off shaded portion.

2

mm

3 x 4mm

Set Screw

2

2mm

Washer

Nut

Linkage Stopper

2

2mm

Place Servos close.

Cut off shaded portion.

Included with the

radio set.

2mm

3 x 4mm

Cut off shaded portion.

Support block for elevator rod.

Drill holes with the specified

diameter (here: 2mm).

2mm

Front

33

Secure foam padding with

rubber bands or tape as required.

Foam Protection

Receiver

Receiver Power Supply

Receiver

Switch

Receiver Power Supply

Install carefuly the receiver and battery pack to

ensure that they will not move during flights.

Place as far forward

as possible.

Must be purchased separately!

Assemble in the specified order.

20mm

Warning!

Make sure to solder securely.

If not properly solderd, a faliure

in flight may occur.

14

34

35

Do not disregard this symbol!

Warning!

Pay close attention here!

Apply epoxy glue.

Cut off shaded portion.

2x6mm

2 x 6mm

TP Screw

TP

Decals

2

mm

2

mm

1

mm

RUDDER

ELEVATOR

AILERON

Adjust the travel of each control surface to the values in the

diagrams. These values fit general flight capabilities.

Readjust according to your needs and flight level.

5mm

If necessary, re-position receiver and battery to get correct

C of G.

Check C of G position before flying.

Ensure all screws are securely tightened before flight.

Warning!

10mm

16mm

CG

185 mm

(from wing leading edge)

Drill holes with the specified

diameter (here: 2mm).

2mm

Pilot holes

This aircraft has been designed for intermediate to experienced level flyers. First time pilots should seek the advice of more experienced flyers during

construction and for initial flights. Initially, less experienced pilots should only fly with an experienced pilot, until they become more proficient. This

aircraft is designed to be powered by either a 2 stroke .15 size engine. Installation of engines other than those specified could to lead to a serious accident

and/or damage to property.

Position for

left diagram.

Position for

left diagram.

Position for

left diagram.

185 mm

C of G position Adjustment

15

36

Decals

For the correct placement of decals, please refer to the box top

and illustrations below.

No.

DF101

DF101-1

DF101-2

DF101-3

DF101-4

DF102

Ducted Fan Set

4500

1000

1500

1000

1200

1000

6500

Ducted Fan Case

Mount Set

Ducted Fan Blade

No. Part Names Quantity

11086-02

11086-03

200

1000

Part Names Quantity

1000

2000

Landing Gear Set

Fuel Tank

90050

Super Tuned Silencer

SPARE PARTS

x1

x1 Set

x1

11086-01

Canopy

FOR JAPANESE MARKET ONLY.

Decal

1701KP

250

Tie Strap (M) LF.Pink

Tie Strap (M) LF.Yellow

1701KY

250

92525

1000

Muffler Joint Pipe

96321

450

Push Choke Button

R

20mm

80mm

PRINTED IN JAPAN

OFF

ON

Before Flying

Before flying your airplane, ensure

the airfield is spacious enough.

Always fly it outdoors in safe areas

with no debris or obstacles!

For handling the radio properly,

refer to its instruction manual.

Ensure the spinner and propeller are

securely attached.

If your airplane begins to operate by

itself, there is another transmitter on

your frequency. Immediately stop

your airplane; otherwise you may

lose control of it which will result in

accidents.

Fully extend

the transmitter

antenna.

Switch on the transmitter.

Switch on the receiver.

Ensure the wings are securely

attached.

Flying

Fill the fuel tank.

By moving the control sticks, ensure

all control surfaces moves as per

your adjustments.

For starting the engine, apply low

throttle and hold the engine starter

against the spinner.

Adjust the needle.

After Flying

Only use KYOSHO genuine parts!

Cautions for Safety

Adjust the engine always from behind,

but never from infront or the sides as

a rotating propeller may badly injure

you!

Do not allow watching people to get

too close to a rotating propeller.

Immediately disuse defective pro-

pellers as well as deformed spinners.

If the dry batteries in the radio are

flat, replace them with fresh ones.

Do not fly your airplane above people

standing around.

ON

Hand-launch your airplane into the

wind to make it take off.

Do not fly your airplane when there

is a strong wind or a lateral wind.

Always land your airplane into the

wind.

Bring your airplane to a halt by

lowering the throttle trim.

After each flight, the engine is very

hot. Beware of getting burned!

Wipe away any fuel deposits or dirt.

Never throw burning, gleaming or

smouldering things into fuel cans,

even if these happen to be empty.

This will result in serious injury!

WIND

OFF

OFF ON

Switch off the receiver.

Switch off the transmitter.

OFF

Draw out the remaining fuel from the

fuel tank and fill it back into the can.

By moving the throttle control

stick, ensure the carburetor opens

and closes without effort.

62150106-3 PRINTED IN CHINA

Always do observe the following in order to prevent accidents!

FLIGHT MANUAL

Warning!

Kyosho F-86F SABRE ユーザーマニュアル

Kyosho F-86F SABRE ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント