INSTALLATION AND
OPERATING INSTRUCTIONS
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before attempting to install, operate or
service the product. Panasonic Please carefully read “INSTALLATION INSTRUCTIONS”
(P.2 4) of this instructions before installation. Failure to comply with instructions
~
could result in personal injury or property damage. Please explain to users how to
operate and maintain the product after installation, and this booklet should be
presented to users. Please carefully read “USE AND MAINTENANCE INSTRUCTIONS”
(P.28 29) of this instructions before operation.
~
Please retain this booklet for future reference.
感謝 選用 產品您Panasonic 。
安裝 使用和保養 產品前 請仔細閱讀本安裝使用說明書 安裝前 請務必先閱讀、Panasonic ， 。 ，
“安裝注意事項”(第 頁) 不遵照此說明書進行操作有可能導致人員受傷或財產損失2 4 。 。
~
，維護Panasonic ，並。安裝完成後 請向顧客說明如何使用和 產品 將此說明書交給顧客保管
，注意事項 28 29 。
~
使用前 請務必先閱讀“使用及維護 ”(第 頁)
請妥善保管好此說明書以備日後參考。
Thermo Ventilator
安裝使用說明書
浴室換氣暖風機
型號：FV-40BEN4H
安全指引
目錄
安裝注意事項
安裝要求
包裝附件清單
部件名稱和尺寸
安裝方法
22 2 4
~
2 4
~5 6
~
5 6
~
8 16
~
8 16
~
66
7
7
ANTIBACTERIAL FUNCTION
HOW TO USE TIMER FUNCTION
HOW TO USE HEATING FUNCTION
HOW TO USE VENTILATION FUNCTION
HOW TO USE DRYING FUNCTION
MODE BUTTON PANEL ON MAIN BODY
TROUBLESHOOTING
WIRING DIAGRAM
SPECIFICATIONS
遙控器功能介紹
定時功能的使用方法
暖氣功能的使用方法
換氣功能的使用方法
風向及風種功能的使用方法
乾燥功能的使用方法
機體模式按鈕面板
抗菌功能
常見故障的識別與處理
電氣原理圖
規格
FUNCTION OF REMOTE CONTROL
21
25
28 29
~
27
30 31
~
33
33
17
19
1717
19
21
20
21
21
20
18
22 23
~
26
32
32
34
34
試運轉
TEST RUN
CONTENTS
SAFETYINSTRUCTIONS
INSTALLATIONINSTRUCTIONS
INSTALLATIONREQUIREMENTS
SUPPLIED ACCESSORIES
PART NAMES AND DIMENSIONS
HOW TO INSTALL
USE AND MAINTENANCE INSTRUCTIONS 使用及維護注意事項
維護方法
MAINTENANCE
安裝前事項 7 8
~
7 8
~
WORK BEFORE INSTALLATION
35 35
溫暖沐浴功能的使用方法
極速排氣功能的使用方法
®
nanoe X功能的使用方法
高效乾衣功能的使用方法
24
25
30 31
~
貼心模式+：
26
27
HOW TO USE WARM BATH FUNCTION
HOW TO USE REFRESH FUNCTION
HOW TO USE DRY CLOTH FUNCTION
CARE MODE+:
17
HOW TO USE AIR DIRECTION AND AIR TYPE FUNCTION
18
24
28 29
~
®
HOW TO USE nanoe X FUNCTION
除菌性能 34
STERILIZATION PERFORMANCE 34
22 23
~
CHECKS AFTER INSTALLATION BACK COVER 安裝後檢查 末頁
為避免給您及其他人造成傷害，這裡我們列出了以下安全注意事項，請務必遵守，各種標誌的
含意請參見以下內容。
對無視表示內容，錯誤地使用時，會引起的危害或損傷的程度，用下列符號進行分類、說明。
警告
注意
本標誌所表示內容為“不遵守的話可能造成人員死亡或重傷”。
本標誌所表示內容為“不遵守的話可能造成人身輕傷或其他財產
損害”。
對希望遵守的內容和種類，用下列符號進行分類、說明。
此標誌表示為禁止事項
此標誌表示為強制事項
此標誌表示為提示注意事項
The degrees of injury or damage that can occur when the instructions are ignored
and if the product is not used properly have been classified and described by the
following indications.
The following instructions should be strictly observed in order to prevent injury to the
users and other people, or damage to property.
This indication means: Must be treated seriously that this may
result in death or serious injury.
WARNING
This indication means: Must be treated seriously that this may
result in injury or physical damage.
CAUTION
Types of instructions that should be observed have been classified and described by
the following pictorial symbols.
This symbol indicates the item is “PROHIBITED” to do.
This symbol indicates the “COMPULSORY” item that must be followed
without failure.
This symbol indicates the item is “CAUTION”.
The product must be grounded.
（ ）Thermo ventilator and cabinet fan
Otherwise, it may cause electric
shock when there is any trouble
or electric leakage.
必須接地(浴室換氣暖風機以及送風機)。
否則當出現故障或漏電時，可能會觸電。
安裝注意事項
安全指引 請務必遵守
2
SAFETYINSTRUCTIONS
INSTALLATION INSTRUCTIONS
Make sure the power cord is
installed firmly.
確保電源線安裝到位。
否則可能會導致火災。
Otherwise, a fire may be caused.
警告
WARNING
This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the by a person responsible for product
the safety. Children should be supervised to ensure that they do not play with the .product
本產品不適合有殘疾、智障或精神障礙的人士或缺乏經驗、常識者(包括兒童)維護使用，除非在負責他們
安全的人士的看護或指導下使用。兒童應該有人進行看護，以防將產品當做玩具。
Disconnect power supply before maintenance.
維護保養前先斷電。
警告
WARNING
否則可能會導致火災。
Otherwise, a fire may be caused.
Doavoidtheback-flowofgasinto
theroomfromtheopenflueof
flammablegasorother open-fire
appliances.
必須避免易燃氣體從敞開的氣道或其他
燃燒燃料的設備回流進室內。
Otherwise, unreliable installation
may be caused and thus the
product may fall off, resulting in
injuries.
Do not install the product as the
method which is not approved in
the instruction.
禁止使用本說明書指定以外的方法
進行安裝。
否則可能會安 裝不牢固，導致 產品
掉落受傷。
Otherwise, combustibles may be
inflamed.
禁止靠近窗簾和其他可燃材料安裝。
否則可能會引 燃可燃物。
否則可能會導致火災。
Otherwise, a fire may be caused.
To avoid danger arising from wrong
resetting of the thermal circuit breaker,
the product can not be powered by
using an external switch. For example,
by a timer or connecting to a circuit
that is connected/disconnected
through timing of a universal part.
為避免由熱斷路器的誤復位產生危險，
產品禁止通過外部開關裝置供電。例如，
定時器或者連接到由通用部件定時進行
通、斷的電路。
3
安裝注意事項
INSTALLATION INSTRUCTIONS
The product is installed so that
switches cannot be touched by a
person in the bath or shower.
Otherwise, anelectricshockmay
becaused.
否則可能會導致觸電。
產品的安裝，應使得浴缸內或淋浴區的
人不能夠觸及到開關。否則可能會導致短路，導致火災。
Otherwise, it may cause a short
circuit, thus resulting a fire.
Please install a suitable all-pole
switch which the contact separation
is more than 3mm. Please install the
all-pole switch out of the bathroom
where it is easily controlled.
安裝時，須在供電線路中安裝其觸點開
距不小於3 mm的“電源全極開關”，
以用於接通或斷開主機電源，且安裝在
浴室外側方便操作的地方。
Disconnectpowersourcebefore
workingontheproduct.
Otherwise, anelectricshockmay
becaused.
安裝、維修保養時必須斷開電源。
否則可能會導致觸電。
Do not install the product near
curtains and other flammable
materials.
Otherwise, it may be on fire.
否則可能會導致起火。
電源線請選用60227 IEC 53(RVV)型軟線，
電源線導線的截面積為3×1.5 mm²聯動，
電源線導線的截面積為2×0.75 mm²。
Please select 60227 IEC 53(RVV)
ordinary polyvinyl chloride sheathed
cord, power cord nominal
cross-sectional area of conductors is
3×1.5 mm², interlock power cord
nominal cross-sectional area of
conductors is 2×0.75 mm².
The product must be installed by
professionals or trained personnel
with equivalent expertise and skills
according to the national wiring
rules.
必須由專業人員或經培訓等具備同等
專業知識和技能的人員按照國家佈線
規則進行安裝。
否則可能會因 錯誤接線、扭絞 接線、
夾線等而導致 漏電、觸電、火災 。
Otherwise, electric leakage,
electric shock or a fire may be
caused due to wrong wiring,
twisted wiring or wire clamping.
4
禁止對本產品進行改造。
請兩人進行產品的安裝作業。
否則可能會導致產品損壞或受傷。
Otherwise, it may cause damage
to the product or personal injury.
Please ensure two persons perform
the installation of the product.
Do not reconstruct this product.
注意
CAUTION
部品安裝必須牢固。
否則可能會掉落，導致受傷。
Components must be installed
tightly.
否則可能會掉落，導致受傷。
Otherwise, it may falloffto cause
personal injury.
Do fix this product tightly.
Otherwise, it may fall off to
cause personal injury.
Otherwise, it may fall off to
cause personal injury.
機體安裝必須牢固。
否則可能會掉落，導致受傷。
有安裝五金件等專用零部件時，應使
用專用零部件。
The special-purpose or dedicated
parts, such as mounting fixtures,
must be used if such parts are
provided.
安裝注意事項
INSTALLATION INSTRUCTIONS
否則可能會掉落，導致受傷。
Otherwise, it may fall off to
cause personal injury.
否則可能會掉落，導致受傷。
Otherwise, it may falloffto cause
personal injury.
Install this product over 2.3 m above
the floor.
Avoiding any accidents
防止意外
產品安裝高度距地面必須大於2.3 m。
警告
WARNING
Do not operate the product other
than the rated voltage
(220 V 50 Hz).
~
禁止使用額定電壓(220 V 50 Hz)以
~
外的電壓。
否則可能會損壞本產品或導致火災。
Otherwise, it may cause damages
to the product or a fire.
否則可能會導致火災。
Otherwise, a fire may be caused.
The product can not be located just
below a power outlet socket.
禁止把本產品安放在電源插座下使用。
產品運作時禁止接觸聯動端子台。
否則可能導致 觸電。
Do not touch the interlock terminal
when the product is working.
It would cause electric shock.
The building structure and
suspender which are used to
installed product must have
sufficient installation strength
and support more than 5 times
weight of the product. They
must be reinforced if their
strength can not be sure.
安裝產品的建築結構和吊桿必須要有
足夠的安裝強度，確保有能承載大 於
產品重量5倍的強度。如 不能確保安裝
強度，請務必采取加固措 施。
請勿安裝在傾斜的天花板上。
防止水倒流。
Do not install onto slanting ceilingboard.
Prevent the water condensed in the
duct pipe flow back into the body.
Pleasemakesuretheproductis installed
horizontallyandthedeviationangle
withintherangeasbelowfigure.
5
Do not install the product in the places
where the organic solvent is used.
Do not install the product in steam
sauna bathroom.
Do not install the product where it is
exposed to oil mist.
Do not install the product in the
places where the sprayer is used.
請勿安裝在桑拿蒸氣浴室中。
請勿安裝在使用噴霧器的場所。請勿安裝在油煙過多的場所。
請勿安裝在使用有機溶劑的場所。
安裝要求
Please set ventilation holes.
Ambient temperature
above 40 °C.
Within
50 cm
50 cm
以內
Do not install the product in places
with high temperature.
請勿安裝在高溫的環境下。
請設置通風口。
周圍溫度 40 °C以上
INSTALLATION REQUIREMENTS
Do not install this product in a public bath room.
Do not install this product in a wardrobe.
請勿把本產品安裝在公共浴室。
請勿把本產品安裝在衣櫃內。
蒸氣
Steam
請確保整機水平安裝偏差角度在±2°之間。
When the ceiling board is unable to
dismantle, please set a square inspection
hole of at least 45 cm (The inspection
hole should not be directly under the
duct pipe).
吊裝且天花板無法拆下時，請設置一個邊長
45 cm以上的方形點檢口(點檢口不能在管道
正下方)。
方便安裝、維修
Convenience for
installation and
maintenance.
The pipe for hanging clothes should be installed at the position of 250 mm
apart from the product, please see P.25 for details.
掛衣用管的安裝應距離產品250 mm，詳細請參考第25頁。
Wave pipe
Adapter
Do not form the duct as shown below:
安裝管道應該避免以下情況：
管道
出風口接頭
請安裝在平整的天花板上。
Please install on a flat ceiling board.
(450 mm)
(150 mm)
點檢口
(450 mm)
square
inspection
hole
(180 mm)
6
包裝附件清單
SUPPLIED ACCESSORIES
4
1
1
3
1
1
1
1
2
3
2
1
2
1
3
4
5
6
7
8
9
10
11
12
Qty
No. Drawing Name and Purpose
Self-tapping screw ( 4 x13, used to install the main
body and the suspension bracket )
Adapter
Suspension bracket
代號 圖樣 名稱及用途 數量
Machinescrew(M4×10,usedtoinstallthelouver assembly)
機械螺絲(M4×10用於面板 組合安裝)
自攻螺絲( 4×13用於機體 與懸吊支 架的安裝)
Product warranty registration
產品保修登記
Installationandoperatinginstructions
安裝使用說明書
Louver assembly
面板組合
Remote control assembly
遙控器組合
出風口接頭
懸吊支架
R03(AAA) Carbon battery
R03(AAA)炭性電池
When you install plastic part, do not exert too much strength to fixing the screw,
otherwise, the product would be damaged.
安裝塑料部件時，為了不損壞產品，鎖螺絲時請注意不要用力過大。
安裝要求
INSTALLATION REQUIREMENTS
The product is not provided with power cord, all-pole switch and leakage
protection switch. Please purchase them in market.
本產品沒有提供電源線，電源全極開關和漏電保護開關，需用戶另購。
Self-tapping screw( 4×8,usedtoinstalltheadapter and
prevent the main body from falling )
自攻螺絲（ 4×8用於出風口接頭的安裝及機體防跌落）
13
Installation cardboard
安裝用紙板 1
Self-tappingscrew( 4×20,usedtoinstallthemain body
and the adapter)( )For installation method 1 only
自攻螺絲( 4×20用於機 體及出風 口接頭的 安裝)（ ）只適用於安裝方法一
Self-tappingscrew( 4×16,usedtoinstallthecontroller
holder) (placed on the backside of controller holder)
自攻螺絲( 4×16用於遙控 器底座安 裝)(放置於 遙控器底 座背面)
Machinescrew
(M4×8,usedtofix the louver and the main body)
2
機械螺絲(M4×8用於面 板與機體 固定)
14
17
26.5
154
60
66
7
部件名稱和尺寸
Unit:mm 單位：mm
Comfirmation before installation
Wall
Product
Unit:mm
單位：mm
提示事項
Notice
安裝前事項
PART NAMES AND DIMENSIONS
WORK BEFORE INSTALLATION
安裝前確認事項
牆
管道
產品
Duct pipe
250 or more
250 or
more
Circulation fan
循環扇葉
Suspension bracket
Louver assembly
Remote control
Filter assembly
面板組合
遙控器
Controller holder
遙控器底座
過濾網組合
懸吊支架
Shutter
Adapter
No . No .Part name Part name
Main body Heater assembly
Baffle plate
Cord cover
序號 序號
部件名稱 部件名稱
接線蓋板
機體 加熱器組合
導風板
高氣密性擋片
出風口接頭
14
13
12
11
10
9
15
1
7
6
5
4
3
2
Ventilation fan
換氣扇葉
8
浴室
Bathroom
250以上
250以上
管罩或管蓋
49
98
371
螺絲蓋
Pipe hood or
Vent cap
472
98 114
394
112
180
Screws cover
226
350
330
電路板蓋板
PCBcover
16
15 16
The distance between ceiling board where the
product is mounted and ceiling shall be over 200 mm.
Please reserve a sufficient length of the power cord
for easy installation, removal and maintenance.
2.
1.
3.
面板組合至 壁的距離在250 mm以上。牆
用於安裝本產品的天花板離房屋頂部的距離在200 mm以上。
請預留足夠長度的電源線，以便於安裝、拆卸與維護。
天花板安裝孔鄰近窗簾和其它易燃材料時，窗簾和其它離
易燃材料距離200 mm以上。
5.
管道通向室外，須開直徑為 110 mm 壁通風孔。牆
（須另購管道、管罩或管蓋）
The distance from louver assembly to walls is
250 mm or more.
When the ceiling mounting hole is adjacent to
curtains or other flammable materials, more
than 200 mm from curtains and other flammable
materials.
When duct pipe is connected to outside of the room,
a vent that diameter is 110 mm should be opened.
(Duct pipe, pipe hood or vent cap are not supply.)
1
2
34
5
6
7
8
9
10
Mode button panel
on main body
機體模式按鈕面板
11
12
13
14
4.
270
2.Preparation before installation
安裝前準備
請於固定佈線與本產品主機間安裝觸點開距不小於3 mm的
“電源全極開關”(規格必須不低於250 V 16 A)及
~
漏電保護開關(洩漏電流在30 mA以下)。
Install an all-pole switch with the contact separation not less
than 3 mm and specifications not lower than 250 V 16 A
~
and a leakage protection switch (with the leakage current
lower than 30 mA) between the fixed wring and the main
body of this product.
安裝前事項
WORK BEFORE INSTALLATION
電源 全極 開關(另 購)
固定 佈線
All-pole switch
(Need to be purchased)
Leakage protection switch
(Need to be purchased)
Fixed wiring
Main body
of this
product
漏電 保護 開關(另 購)
本產品主機
安裝方法
HOW TO INSTALL
8
1-1 Main body installation
Method 1 Ordinary ceiling board mounting
機體的安裝
方法一 普通天花板吊裝
提示事項
Notice
Open a 280 mm x400 mm mounting hole
in the ceiling board.
在天花板上開一個280 mm x400 mm的安裝孔。
Unit:mm
單位：mm
天花板
Ceiling board
400
280
Position and install the suspenders(M8 or M10
suspenders need to be purchased).
吊桿的定位安裝（另購M8或M10）。
Taking out the installation cardboard from the
accessory package, align the four corners of the
opening with those of the installation cardboard,
and then paste the installation cardboard onto
the ceiling.
將產品附帶的安裝用紙板的四角與天花板開口部的四角
對齊後，將紙板貼於水泥板。
(1)
Fix the suspenders on the ceiling according to
the location holes as shown in the installation
cardboard.
按照安裝用紙板所示的吊桿固定位置，將吊桿固定
於水泥板上。
(2)
After fixing the suspenders, please rip off
the installation cardboard.
吊桿固定完成後請將安裝用紙板撕掉。
水泥板
天花板開口部
紙板定位角
安裝用紙板
Installationcardboard
Ceiling board
opening
Cardboard
positioning
corner
Ceiling
Installation cardboard
安裝用紙板
懸吊支架的安裝。
將懸吊支架固定於吊桿。
調整吊桿上的螺母，使懸吊支架的底部緊貼天花板。
（1）
（2）
Fix the suspension brackets to the suspenders.
Adjust the nut on the suspenders to make the
suspension bracket bottom cling to the ceiling
board.
Install the suspension brackets. 安裝用紙板
Installation cardboard
Suspender
吊桿
Ceiling
水泥板 Ceiling
board
天花板
Suspension
bracket bottom
懸吊支架底部
螺母（另購）
Nut(not ) included
Nut(not
included)
螺母（另購）
懸吊支架
Suspension
bracket
Installation cardboard
安裝用紙板
墊片（另購）
Washer(not
included)
墊片（另購）
Washer(not
included)
懸吊支架的底部務必要緊貼天花板，否則可能會導致機體無法安裝。
提示事項
Notice
Make sure that the suspension bracket bottom clings to the ceiling board; otherwise the main
body cannot be installed successfully.
9
安裝方法
HOW TO INSTALL
Self-tapping
screw 4 x20
自攻螺絲 4x20
天花板邊緣
Adapter
出風口接頭
Use the supplied 4×20 self-tapping screw to fix
the adapter to the ceiling board.(The adapter must
fix to the ceiling edge.)
用附件包所提供的1顆 4×20自攻螺絲，將出風口接頭
固定於天花板上。（接頭必須緊貼天花板邊緣）
Ceiling edge
70 mm
5Connecting the duct pipe Refer to Section
3.Duct Pipe Connection on P.15.
連接管道。參考第15頁 3.管道的連接
6Connecting thermo ventilator power cord
浴室換氣暖風機電源線的連接
Strand the core wire together after stripping,
then insert them into about 8 mm deep position
of the terminal block, ensuring that the part is
under the spring slice, and no copper core cord is
exposed outside. Make sure that the copper core
cords are fixed by screws reliably (the .
recommended screw fixing torque is 0.49 N m)
(See Figure 2). Otherwise an electric shock may
be caused.
先將剝線後分散的銅芯線絞合在一起，然後伸入到端子
台約8 mm深，並確保其在彈簧片的下方，切勿出現銅
線外露現象。螺 擰緊後，請確保銅線不易鬆脫(建議絲 .
螺 鎖緊扭矩為0.49 N m)，否則可能會導致觸電。絲
(右圖2)
電源線的 緣膠不能破損，否則可能會導致觸電或短路。絕
剝線長度，請按照剝線示意圖(右圖1)進行剝線，如剝線
過長，可能會導致產品短路。
警告
WARNING
安裝和使用時禁止拆卸電路板蓋板，否則可能會導致觸
電或起火。
To avoid electric shock or fire, do not remove the
PCB cover.
For the stripping length, please prepare
according to the wiring sketch (refer to figure 1).
If the stripping length is too long, it may cause
short circuit.
Do not damage the sheath of the power cord,
otherwise an electric shock or short circuit may
be caused .
Figure 2
Conductor
Insulation
Spring slice
Terminal cutaway view
接線柱剝面圖
銅芯線
絕緣膠
彈簧片
圖2
Unit:mm
單位：mm
Figure 1
Conductor
Earth
Power cord
44±1
Wiring sketch
剝線示意圖
Unit:mm
單位：mm
電源線
接地引線
銅芯線
圖1
41
銅芯線
CONDUCTOR
聯動電源線
INTERLOCKPOWER CORD
Unit:mm
單位：mm
Please select 60227 IEC 53(RVV) ordinary polyvinyl
chloride sheathed cord. Power cord nominal
cross-sectional area of conductors is 3×1.5 mm².
Interlock power cord nominal cross-sectional area
of conductors is 2×0.75 mm².
電源線請選用60227 IEC 53(RVV)型軟線 電源線導線，
的截面積為3×1.5 mm²聯動電源線導線的截面積為，
2×0.75 mm²。
安裝方法
HOW TO INSTALL
Openthecordcover.
(1)Remove the screw on the cord cover.
(2)Open the cord cover.
(3)Lift the terminal cover(Do not remove
the terminal cover).
打開接線蓋板
（1）取下接線蓋板上的螺絲。
（2）打開接線蓋板。
（3）掀起端子保護蓋（請不要拆下此保護蓋）。
電路板蓋板
PCBcover
(1)
(2)
(3)
Terminal cover
(Do not remove
this cover)
端子保護蓋
（請不要拆下
此保護蓋）
Cord cover
接線蓋板Self-tapping
screws 4 x 8
自攻螺絲 4 x 8
6-1
Loosen the screws of the pillar terminal, insert
the power cord(not supplied)connected to the
fixed wiring which in the house into the pillar
terminal, tighten the screw.
鬆開接線柱上的螺絲，將接入室內固定線路的電源線
（用戶自購）插入接線柱，擰緊接線柱螺絲。
Screws
螺絲
線夾
Cord clip
Terminal
接線柱
地線
Earth
wire
用線夾將電源線固定。(線夾必須壓住電源線絕緣護套)
Fix the power cord with the cord clip. (The
cord clip must pin the insulation sheath of
power cord.)
Screws
螺絲
線夾
Cord clip
Terminal cover
端子保護蓋
Fix the cord cover by the screws which removed by step .
用步驟 拆下的螺絲，將接線蓋板重新固定。
注意
CAUTION
When covering the terminal cover, be sure not to suppress
the earth wire, otherwise it may damage the earth wire.
蓋端子保護蓋時，請注意不要壓到地線，否則可能會壓傷地線。
6-3
6-4
6-56-1
6-1
Loosenthescrewsofthecordclip.
將固定電源線線夾的螺絲鬆脫。
6-2
7
連接 。(如有需要，請按以下方法進行連接)Panasonic送風機聯動電源線
Connecting Panasonic cabinet fan interlock power cord. (If it is necessary, please connect
it by the following connection method.)
電路板蓋板
PCBcover
(1)
(2)
Terminal cover
(Do not remove
this cover)
端子保護蓋
（請不要拆下
此保護蓋）
Cord cover
接線蓋板
Self-tapping
screws 4 x 8
自攻螺絲 4 x 8
送風機聯動電源線連接時，請確保本產品處於斷電狀態。
否則可能會導致觸電。
警告
WARNING
Be sure to disconnect the power before
connecting cabinet fan interlock power cord,
Otherwise, anelectricshockmaybecaused .
取下聯動電源線接線蓋板的螺絲，
打開聯動電源線接線蓋板。
Remove the screw on the interlock power cord
cover. Open the interlock power cord cover.
Remove the screw on the cord cover.
Open the cord cover.
取下接線蓋板上的螺絲，打開接線蓋板。
Interlock cord coverpower
聯動電源線接線蓋板
Screws
螺絲
7-1
7-2
10
安裝方法
HOW TO INSTALL
將固定聯動電源線線夾的螺絲鬆脫。
Loosenthescrewsofthecordclip.interlock power Screws
螺絲
Interlock power
cord
聯動電源線
7-3
7-4
用線夾將聯動電源線固定。
(線夾必須壓住聯動電源線絕緣護套)
Fix the nterlock power with the cord clip.i cord
(The cord clip must pin the insulation sheath
of nterlock power cord.) i
7-5
線夾
Cord clip
Access power Please reserve a interlock cord.
sufficient length of the power cord for easy
installation, removal and maintenance.
接入聯動電源線，且預留足夠長度的電源線，
以便於安裝、拆卸與維護。
用步驟 拆下的螺絲，將 接線蓋板重新固定。聯動電源線
再用步驟 拆下的螺絲，將接線蓋板重新固定。
Then fix the cord cover again by the screws which removed
in step .
Fix the interlock powercord cover again by the screws
which removed in step .
7-6
7-2
7-1
7-2
7-1
提示事項
Notice
聯動的產品僅限使用Panasonic的送風機，型號為：FV-12NS3H、
FV-15NS3H、FV-18NS3H、FV-18NF3H、FV-20NS3H
使用其他送風機可能會損壞產品。
繼電器必須使用IEC 255 5 A 250 V AC型。 (另購)
請務必按照要求連接產品，錯誤接線可能會燒毀電路板。
接線方法如右圖兩種方案(方案2中繼電器對線路具有保護作用)，
其他接線方法可能會損壞產品。
繼電器需要放置在合適的區域，避免濕氣入侵或水噴淋到。
1.The wiring method is as shown in the right figure (the relay
in example 2 can protect the circuit). Other wiring methods
may damage the product.
2 The interlock output power can not exceed 220 V/1 A, and .
make sure the wiring method is correct, otherwise the main
control circuit board may be burned out.
3.Be sure to connect the product as required, and incorrect
wiring may burn the board.
4.The interlock products are limited to use Panasonic cabinet fan,
model: FV-12NS3H, FV-15NS3H, FV-18NS3H, FV-18NF3H,
FV-20NS3H. Using other blowers may damage the product.
5.The relay must use the IEC 255 5 A 250 V AC type. (Not included)
6.The relay needs to be placed in a suitable area to avoid
moisture ingress or water spray.
7.For the installation of the cabinet fan, please refer to the
corresponding instructions of cabinet fan model. (The
interlock interface of this product does not have a
grounding function. Please ground the cabinet fan
according to its corresponding manual.)
送風機的安裝，請參考送風機型號對應的說明書。（本產品的聯動
接口不具備接地功能，送風機的接地請按照其對應的說明書。）
電源輸入
接入送風機
例2 示意圖
Example 2 sketch
L
N
L
N
繼電器
繼電器底座
聯動電源接線
Relay
Relay holder
Interlock power
cord
Access cabinet fan
Power input
聯動輸出不能接入超過220 V/ 1 A的產品，且確保接線正確，
否則可能燒壞電路板。
11
安裝方法
HOW TO INSTALL
Push the main body upward into the ceiling
board by closely leaning against the adapter, clip
the clipping position of the main body into the
locating slot of the adapter (otherwise, it may
have air leakage), and fix the main body with
three 4 x13 self-tapping screws.
將機體緊靠出風口接頭往上推入天花板，並使
機體上卡位卡入出風口接頭定位槽中(否則漏風)，
用3顆 4x13的自攻螺絲將機體牢固地固定。
出風口接頭定位槽
懸吊支架螺絲孔
自攻螺絲 4×13（3顆）
機體卡位
Clippingposition
ofthemainbody
Suspensionbracket
screwhole
Self-tapping screws
4×13 (3 pcs)
Locating slot of the adapter
8
注意
CAUTION
固定機體的螺絲，必須通過懸吊支架螺絲孔將機體固定
於懸吊支架和天花板，否則產品有掉落的危險。
Use one 4 x 8 self-tapping screw to fix the
adapter. Be sure to fix this screw because it
can prevent the main body from falling off
the ceiling board.
用 顆 的自攻螺絲將 牢固地固定1 4x8 出風口接頭 ，
。此螺絲能起到防止機體脫落的作用，請務必安裝
Cross screwdriver
(not longer than 150 mm)
十字螺絲刀
(長度不大於150 mm)
Self-tapping
screw 4 x8
自攻螺絲 4x8
Thescrews for fixing the main body to the ceiling
board should go through the hole of the suspension
brackets, otherwise, product may fall down.
9
After completion of the installation work, be
sure the condition between the main body and
the adapter is proper. It can be checked from
the inspection hole.
提示事項
Notice
安裝完成後，請務必從點檢口確認機體與出風口接頭
的安裝是否到位。
10
如機體與出風口接頭未貼緊，會導致漏風及影響 中防止機體脫落的作用。
9
If the body and the adapter are not tightly attached, it will cause
air leakage and affect the function of preventing the body from
falling off in step .
9
Gap
縫隙
12
安裝方法
HOW TO INSTALL
3
8Install the ceiling board.
用附件包所提供的 4x13 ，的自攻螺絲
將懸吊支架固定於 。機體
5Fix the main body to the suspenders.
將機體固定於吊桿。
安裝天花板。
Fix the suspension bracket to the main body
with the 4×13 self-tapping screws provided
in the accessory package.
6Connecting the duct pipe Refer to Section
3.Duct Pipe Connection on P.15.
連接管道。參考第15頁 3.管道的連接
After complete the installation work, please
rip off the installation cardboard.
安裝完成後，請將安裝用紙板撕掉。
7
天花板請安裝于機體法蘭上側，否則可能會導致面板組合無法正確安裝。
提示事項
Notice
Self-tapping
screws 4 x13
自攻螺絲 4x13
Fix the adapter to the main body with the 4x8
self-tapping screw provided in the accessory
package.
2
用 顆 的自攻螺絲附件包所提供的1 4x8 ，
將出風口接頭固定於 。機體
Please install the ceiling board on the upper side of the main body flange.
Otherwise, the louver assembly may not be installed correctly.
4
機體法蘭
Ceiling board
天花板
Main body
flange
螺母（另購）
Nut(not )included
Nut(not included)
螺母（另購）
懸吊支架
Suspension
bracket
墊片（另購）
Washer(not
) included
墊片（另購）
Washer(not
) included
Self-tapping
screw 4 x8
自攻螺絲 4X8
連接電源線 參考第9～11頁 電源線的 連接
Connecting power cord Refer to Section
Connection method on P.9～P11.
67
～
67
～
13
1-2 Main body installation
Method 2 Ceiling board has not been installed
1
機體的安裝
方法二 未裝天花板吊裝
Unit:mm
單位：mm
Positioning and installing the suspenders.
吊桿的定位安裝。
Ceiling
水泥板
Suspender
吊桿
安裝用紙板
Installationcardboard
Paste the installation cardboard provided on the
position where the main body is intended to be
installed.
將產品附帶的安裝用紙板，黏貼在機體預定安裝的位置。
Fix the suspenders on the ceiling according to the
location holes as shown in the installation cardboard.
按照安裝用紙板所示的吊桿固定位置，將吊桿固定於水泥板上。
(1)
(2)
Installation carboard
安裝用紙板
安裝方法
HOW TO INSTALL
面板組合安裝
2. Installing louver assembly
將過濾網組合從面板組合拆除。
Remove the filter assembly from the louver assembly.
2
將雙層面板的前面板打開，向上掀即可打開。
掀開向上
Liftupward
Openthe frontpanel of the louver assembly
by lifting it upward.
將面板組合掛入機體上的掛鉤。
Hang the louver assembly into the hook
on the main body.
Main body
hook
機體掛鉤
Insert the screw cover with a slotted screwdriver
and pry the screw cover outward. Fix the louver
assembly to the main body with four M4×8 machine
screws provided in accessory packaging.
用一字螺絲刀插入螺絲蓋的縫隙，往外撬開螺絲蓋。
使用附件包所提供的4顆M4×8機械螺絲將面板組合
固定於機體。Machine screw
M4×8
機械螺絲
M4×8
請注意不要刮花面板組合。
Please be careful not to scratch the .louverassembly
提示事項
Notice
注意
CAUTION
務必用螺絲緊固前面板與面板底座。
否則前面板可能會掉落導致受傷。
■Be sure to fasten the front louver and the
louver holder with screws.
Otherwise ,the front panel may fall and
cause injury.
將撬開的螺絲蓋重新蓋好，使 螺絲 將面用2顆M4×10機械 ，
。板組合的前面板固定於面板底座
Covering the screw cover, fixthefrontpaneloflouver
assemblyto louverholderbyusingthetwo machine
screws M4×10. Machine screw M4×10
機械螺絲M4×10
螺絲蓋
Screw cover
將過濾網組合重新安裝回面板組合。
Install the filter assembly back into the louver assembly.
導風板支架
Baffle plate holder Louver assembly
面板組合
提示事項
Notice
安裝完成後，請確保導風板支架突出面板組合約1 mm。
否則可能導致面板組合變形。
1 After finishing installation, make sure that the baffle .
plate holder protrudes from the louver assembly by
approximately mm.1 Otherwise it may cause the filter
assembly to be deformed.
約1 mm
About 1 mm
請確保面板組合及過濾網安裝到位，否則可能導致灰塵、毛髮等異物進入。
2.Make sure that the and filter are installed louver assembly assembly
in place, otherwise foreign matter such as dust and hair may enter.
14
安裝方法
HOW TO INSTALL
15
送風機管罩請選擇對應送風機型號的管罩。
5.For the cabinet fan pipe hood, please select the corresponding pipe hood of the cabinet
fan model.
3.Connecting duct pipe (Not )included
Take out the remote control from the holder.
遙控器的安裝
把遙控器從遙控器底座抽出。
4.Installing the remote control
Check the main body can receive the signal from the intended remote control installation
location. If remote control can not receive the signal from this installation location, please
choose another installation location, or operate the remote control toward product after
taking out it from the holder. The installation location cannot be toward the direct spraying
area of the shower.
遙控器安裝前，請在預定安裝的位置上檢測機體接收信號的效果，若該位置無法使機體正常接收，請
另選擇合適的位置或使用時把遙控器從底座中取出對著機體進行操作。且安裝位置應避免在花灑直淋處。
管道的連接(另購)
底座
Holder
Pull up
遙控器
向上拔出
Remote
control
送風機管道的 及安裝方法請參考送風機的說明書，其他安裝問題請 。連接 諮詢信興電器服務中心有限公司
Please refer to the instructions of cabinet fan for the connection and installation method of
cabinet fan pipe. For other installation problems, please contact Shun Hing Electric Service
Centre Ltd.
100 50
1 1
( 100 mm)
Pipe
( 98 mm)
Adapter
Indoors Outdoors
Slant taper
出風 口接 頭
( 98 mm)
( 100 mm)管道
屋內
傾斜 角度
屋外
1
2Install the pipe hood or vent cap on the external wall.
(Please purchase a pipe hood or vent cap separately according to the pipe size.)
將管罩或管蓋安裝到屋外。
(請根據管道尺寸另外購買管罩或管蓋)
Install the duct pipe onto the adapter, and
then bind them tightly with adhesive tape.
Suspend the duct pipe from the ceiling board
to prevent external force exerted on the unit
body.
將管道裝入出風口接頭上，然後用膠帶紮緊。
將管道從天花板上懸掛下來，以防止外力施
加於機體。
提示事項
Notice
牆壁通風孔最小直徑： 110 mm。
The minimum diameter of the hole: 110 mm.
The duct pipe connected to outside of the room must be slanted to prevent rain or condensed water
from flowing backwards.
通往屋外的管道必須保持傾斜，防止雨水或結露水倒流。
1.
2.
3.
4.
不安裝管罩或管蓋可能造成鳥、蟲、鼠等的進入。
管道長度要盡可能適中，過長會影響產品性能，管道最長不要超過30 m。
This duct pipe length should be as moderate as possible. It will affect product performance
if it is too long. Total length of the duct pipe should be shorter than 30 m.
Failure to install a pipe hood or vent cap may result in the entry of birds, insects, rats, etc.
安裝方法
HOW TO INSTALL
Please back the remote control to the holder.
將遙控器放回遙控器底座。
在浴室的牆壁上開2顆 6的安裝孔，將遙控器
底座安裝於牆上。
Open two 6 holes in the bathroom wall
as shown below. And install the controller
holder.
Do not short circuit.
Please observe the following when using the batteries.
電池的使用請遵守以下內容。
勿將電池正負反裝。
勿將新舊、異種電池混合使用。
長期不使用時，請取出電池。
更換電池時，請擦乾遙控器機體後進行更換。
不可短路。
(否則可能會導致漏液或破損)。
警告
WARNING
Do not inversely install the positive
pole and negative pole of batteries. Do not use an old battery together
with a new battery or use different
types of batteries in a mixed way.
(Otherwise, aleakage or damagemaybecaused.)
2.Do not replace the batteries when the remote control body is wet.
1.lf you will not use the remote control for a period of time, take out the batteries.
3.Do not exert too hard when you rotate the" " knob on the remote control back,
otherwise the knob will be damaged.
旋動遙控器背部 字旋鈕時，請勿用力過大，否則可能會損壞該旋鈕。
丟棄電池時，請遵循當地法律法規。
Please comply with local laws and regulations when dispose the battery.
提示事項
Notice
Install two R03(AAA) carbon batteries in the
remote control.
將2粒R03(AAA)炭性電池放入遙控器中。
4.If the battery cover is not tightened, it will affect the sealing effect.
如果電池蓋未蓋緊，會影響密封效果。
膠塞( 6×26 mm)(另購)
36 mm
自攻螺絲( 4×16 mm)
2-6深28 mm
2-628 mm
Plastic plug( 6 x 26 mm)
(not )included
Self-tapping screw
( 4 x 16 mm)
供安装人员阅读
將旋鈕 向左轉至
“ ”位置
(1)Rotate the knob “ “
leftward to the “ ”
position.
[關]的狀態
[Close]status
[開]的狀態
[Open]status
(3)Install two R03(AAA) carbon
batteries in the remote control.
(Pay attention to the directions of
“ ” and “ ”)
將兩粒R03(AAA)炭性電池放入遙控
器中。(注意 ， 方向)
(4)Replace the battery cover.
重新蓋上電池蓋。
將旋鈕 向右轉至“ ”位置。
(5)Rotate the knob “ ” rightward to
the “ ”position.
旋鈕
knob
打開電池蓋。
(2)Open the battery cover.
切勿為非充電式電池充電。
Non-rechargeable batteries should
not be recharged.
16
TEST RUN
試運轉
FUNCTION OF REMOTE CONTROL
遙控器功能介紹
Increases running time
增加定時運轉時間
TIMER button 定時按鈕
STANDBY button
In the standby status, this product
still requires power consumption
of 0.5 W. If the product will not
be in use for a long time, the
all-pole power switch should be
turned off to disconnect the
power supply for the purpose of
energy saving.
待機按鈕
本產品處於待機狀態時，仍有0.5 W
的功耗。如長時間不使用時，應使用
電源全極開關斷開電源，以節省能源。
HEAT button
Heating function
暖氣功能
暖氣按鈕
DRY button
乾燥按鈕
Change the air direction
(FIXED/AUTO)
切換風向設置
(固定/自動)
SWING button 風向按鈕
VENT. button
Ventilation function
換氣功能
換氣按鈕
Warm bath function
溫暖沐浴功能
WARM BATH button
溫暖沐浴按鈕
Dry cloth function
高效乾衣功能
DRY CLOTH button
高效乾衣按鈕
Refresh function
極速排氣功能
REFRESH button
極速排氣按鈕
CARE MODE+
貼心模式+
Decreases running time
減少定時運轉時間
Air type button 風種按鈕
SPOT: The air is focused in a spot and
the speed is high.
“集中”：集中的風種，風比較集中且快速。
WIDE: The air distribution is wide and
the speed is low.
“擴散”：擴散的風種，風比較均勻且緩慢。
2.After connecting the power, the product enters REFRESH function automatically. Meanwhile, the
interlock cabinet fan starts(Please see P.26 for details). Users please check the following items
using the remote control:
接通電源 請按後，產品自動進入極速排氣功能，同時聯動的送風機也會啟動（具體參照第26頁的介紹），顧客
遙控器上各個功能按鍵 檢查以下項目， ：
Does the fan revolve normally?
扇葉是否正常旋轉？
Does it have abnormal vibration or noise?
是否有不正常的震動或者噪音？
Does it blow out hot air?
是否有熱風輸出？Is each button on remote control perform its right function?
遙控器上的各個功能按鈕的功能是否正常？
安裝完成及接通電源後，產品自動進入極速排氣功能，同時聯動的送風機也會啟動（具體參照第26頁的介紹），
顧客請按“模式按鈕”以確認產品能正常運轉，功能切換正常。
After installing and connecting the power, the product enters REFRESH function automatically.
Meanwhile, the interlock cabinet fan starts (Please see P.26 for details). Users please press
“mode button” to confirm the product is operated normally and the function is switched properly.
1.
Change the dry mode
(COOL/HOT)
切換乾燥方式
(涼乾燥/熱乾燥)
The product will start the in the ventilation mode and the dry mode.cabinet fan
產品在換氣狀態及乾燥狀態下會啟動送風機。
Press and hold the button for 3
seconds, the product will restore
the initial settings .
長按 按鈕3秒，產品將恢復初始設置。
®
nanoe X button
®
nanoe X function
®
nanoe X功能
®
nanoe X按鈕
17
風向及風種功能的使用方法
HOW TO USE AIR DIRECTION AND AIR TYPE FUNCTION
運轉中可通過 按鈕，調節風向。
Default mode:[FIXED]. Default HOT mode and COOL mode: [AUTO].
暖氣模式的出廠設置為：[固定]。熱乾燥、涼乾燥模式的出廠設置為：[自動]。
取消自動記憶模式，請長按 按鈕3秒。
Air direction cannot be set in the mode and . mode
換氣模式 不可進行風向設置
®
和nanoe X模式 。
During running, you can press the button to adjust the air type.
Default and HI mode: [SPOT]. Default and Lo mode:[WIDE]
暖氣模式強檔的出廠設置為：[集中]。 弱檔為：[擴散]
The default HOT mode and COOL mode is
[SPOT（9min）→WIDE（13.5min）→SPOT（9min）···] switched cyclically.
熱乾燥、涼乾燥模式的出廠設置為[集 中（9分鐘）→擴散（13.5分鐘）→
集中（9分鐘）...]循環切換。
To cancel the automatic memory mode, press and hold the button for 3s.
取消自動記憶模式，請長按 按鈕3秒。
Air type cannot be set in the mode . and mode
換氣模式 不可進行風種設置
®
和nanoe X模式 。
To cancel the automatic memory mode, press and hold the button for 3s.
運轉中可通過 按鈕，調節風種。
During running, you can press the button to adjust the air direction.
For adjusting air direction
調整風向時使用
For adjusting air type
調整風種時使用
※
※
通過 鍵，可進行自動與固定的切換。
You can press the button change the mode between AUTO and FIXED.
3
4
3
4
Heating mode will automatically memorize the air direction position set
this time.
暖氣模式會自動記憶本次設置的風向位置。
Heating mode will automatically memorize the air type position set this time.
暖氣模式會自動記憶本次設置的風種位置。
風向 風 種
集中 擴 散
固定
固定
固定
自動
自動
自動
120
120
自動及固定模式時，導風板具體變動範圍如下表。
暖氣 模式
涼乾 燥模 式
熱乾 燥模 式
導風板
（自 動 模式）
約60° 約120° ）
符號代表自動循環運轉。
符號代表轉動範圍，如對風種 無設置時，
將自動按此轉動範圍進行轉動。
HEAT mode
DRYCOOL
mode
DRYHOT
mode
Air direction Air type
FIXED
SPOT WIDE
AUTO
FIXED
AUTO
FIXED
AUTO
About 60° About 120°
（SPOT）
（集 中 ）
Automatic
Baffle plate
風向角度
Air direction angle
The symbol indicates the automatic
circulation running mode.
The※symbol indicates the rotation range. If the air
type is not set, the air deflector will automatically
rotate according to this rotation range.
1.
2.
The moving range of the baffle plate for both automatic
mode and fixed mode is shown in the table. 集中
SPOT
擴散
WIDE
FIXED : To fix the baffle plate angle, press the button then the baffle
plate turns to the required position. The baffle plate will stop.
固定：需固定導風板角度時，待導風板轉到所需位置，按 按鈕，導風板將
停止轉動。
※
（WIDE）
（擴 散)
18
HOW TO USE TIMER FUNCTION
定時功能的使用方法
VENT. mode
換氣模式
Default settings
CONT
5 MIN. 15 MIN.
12 HOUR 出廠設置為
DRY HOT mode
熱乾燥模式
Default settings
5 MIN. 15 MIN.
6 HOUR 出廠設置為
HEAT mode
Default settings
5 MIN. 15 MIN.
3 HOUR 出廠設置為
暖氣模式
Default settings 3 HOUR
出廠設置為
Default settings 30 MIN.
出廠設置為
Default settings 15 MIN.
出廠設置為
CARE MODE+ : WARM BATH mode
貼心模式+ ：溫暖沐浴模式
5 MIN. 3 HOUR
CARE MODE+ : DRY CLOTH mode
貼心模式+ ：高效乾衣模式
5 MIN. 6 HOUR
CARE MODE+ : REFRESH mode
貼心模式+ ：極速排氣模式
1
2
During running, you can press the button to change the running time.
If you press and hold the button, the running time keeps changing.
After the running time is set once, the system will automatically
memorize the last running time of each mode.
To cancel the automatic memory content, press and hold the
button for 3 seconds.
調整運轉時間時使用
如連續按，運轉時間會連續快速變換。
取消自動記憶內容，請長按 按鈕3秒。
設置一次運轉時間後，會自動記憶每個模式上一次的運轉時間。
Each time you press the button, the time increases accordingly.
每按一次 按鈕，時間會隨之遞增；
Each time you press the button, the time decreases accordingly.
每按一次 按鈕，時間會隨之遞減；
For adjusting running time
在上記運轉模式中每按一次 按鈕，時間會以5分進行增減，1小時後時間會以
30分鐘進行增減。
Inthe above running mode, each time you press the button, the time
changes at the step of 5 minutes; one hour later, the time will changes
at the step of 30 minutes.
運轉中可通過 調整運轉時間。
Default settings
CONT
5 MIN. 15 MIN.
12 HOUR 出廠設置為
DRY COOL mode
涼乾燥模式
※
The time can not be adjusted.
時間不可調整。
Default settings
CONT
5 MIN. 3 HOUR
12 HOUR 出廠設置為
®
nanoe X mode
®
nanoe X模式
19
Use when you feel cold in a bath
在浴室中感到冷時使用
在沐浴前開暖氣功能，可提前將浴室升溫。
Before taking a bath, start the heating function to warm the bathroom
beforehand.
暖氣功能的使用方法
HOW TO USE HEATING FUNCTION
Heater may stop heating when temperature in bathroom is up to required degree, and may
restart heating as the temperature in bathroom cools down.
2.
1.
當浴室內溫度上升到一定程度時，加熱器停止工作，待溫度下降到一定程度後，加熱器重新開始工作。
提示事項
Notice
1Press the button to start the heating mode at the HI.
It will switch to the LO. mode if you press this button again.
按 按鈕，暖氣模式以[強檔]開始運轉，再按一次將切換為[弱檔]。
(Initial settings)
(初始 設置)
強
HI 弱
LO
The default [SPOT] is recommended. The air type can be reset during
operation.
推薦使用出廠設置狀態[集中]，運轉中也可以重新設置風種。
The default setting is 15 minutes. You can adjust it as required.
出廠設置狀態為15分 鐘，用戶可根據需要自行調整。
The default [FIXED] is recommended. The air direction can be reset
during operation.
推薦使用出廠設置狀態[固定]，運轉中也可以重新設置風向。
3.Heating performance may change after the cabinet fan is installed in the bathroom.
浴室內安裝送風機后，暖氣性能可能會發生變化。
Hot startup function: After the product starts up in the high heating mode when the
temperature in the bathroom is lower than 20 °C, it enters the hot startup status to avoid
blowing of cold air, and the fan runs at a low speed. When the temperature in the bathroom
reaches 20 °C or above or after running for 60 seconds, the hot startup status stops and the
fan runs at a high speed.
熱啟動功能：當浴室溫度低於20 °C時，以暖氣強檔模式啟動後，為避免冷風吹出，產品進入熱啟動狀態，
扇葉以低速運轉，待浴室溫度達至20 °C以上或經過60秒後，熱啟動狀態停止，扇葉以高速運轉。
In the heating mode running for 30 seconds above, press the
button to stop the heater. The fan will stop running after a delay
of 20 seconds.
2
3
運轉完所設置時間後，本機會自動停止。
如需在運轉途中停止，請按 按鈕。
若在暖氣模式運轉30秒以上，按 按鈕後 ，為使加熱器冷卻，
扇葉將延遲20秒停止運轉。
This product will stop automatically when the set time is up.
To stop midway in running,pressthe button.
20
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
