型號
使用說明書
空氣清新機
本產品為室內專用
目錄
設置與使用要求
安全注意事項
使用方法
維護保養
長期閒置時
更換過濾網
智慧節能·PM2.5·定 時
運轉關/開·風 量
兒童安全鎖
更多信息
常見問題解答
故障排除
規格
自選配件
末頁
末頁
附保證書
感謝您選購 Panasonic 產 品。
使用和維護產品前，請仔細閱讀本使用說明書。
使用前，請務必先閱讀“安全注意事項”（第2~5頁 ）。
不遵照本說明書進行操作有可能導致受傷或財產損失。
請確認保證書中已填寫“購買日期、經銷商名稱”等信息後，將其與使用說明書一同進行妥善保管。
確
認
與
設
置
使
用
方
法
維
護
保
養
其
他
信
息
15~18
19
15~18
11~13
18 18
19
15
15
FURTHER INFORMATION
FAQ
BACK COVER
TROUBLESHOOTING
SPECIFICATIONS
OPTIONAL ACCESSORIES
SETTING AND OPERATING REQUIREMENTS
Thank you very much for purchasing this Panasonic product.
Please read these operating instructions carefully before operation and maintenance.
Also, be sure to read the “SAFETY PRECAUTIONS” section (P.2~5) before use.
Failure to comply with instructions could result in injury or property damage.
Make sure that the correct information is written on the warranty card, including the date of
purchase and the name of the distributor. Keep the warranty card in a safe place along with the
operating instructions for future reference.
Warranty card attached
Air Purifier
Model No.
This product is for indoor use only
OPERATING INSTRUCTIONS
CONTENTS
OPERATION
BACK COVER
清潔方法 14
主要部件名稱 8
設置 9~10
OPERATION
8
MAIN PARTS IDENTIFICATION
POWER OFF/ON·AIR VOLUME
CHILD LOCK
ECONAVI·PM2.5·TIMER
MAINTENANCE
WHEN IDLE FOR A LONG TIME
CLEANING METHOD
FILTER REPLACEMENT
SAFETY PRECAUTIONS 2~5
PRODUCT FEATURES 6~7
5~65~6
2~5
產品特點 6~7
11 11
13
12
12
13
15
SETUP 9~10
11~13
13~15 13~15
14
15
CONFIRMATION
AND SETUP
MAINTENANCE OTHER
INFORMATION
安全注意事項
以下標誌是根據不按指示使用產品所產生的危險或受傷程度進行分類。
注意警告
本標誌所表示的內容為“不遵守的話可能造成人員
死亡或重傷”。
本標誌所表示的內容為“不遵守的話可能造成人身
輕傷或財物損害”。
以下標誌為務必遵守的指示種類。（下列標誌為例子。）
此標誌表示禁止事項。 此標誌表示強制事項。
SAFETY PRECAUTIONS
CAUTIONWARNING
警告
WARNING
The safety precautions should be strictly followed in order to prevent injury or damage to properties.
為了避免對您或其他人造成傷害或財物損害，請務必遵守安全注意事項。
This symbol indicates an action that
must not be performed.
This symbol indicates an action that
must be performed.
The following symbols differentiate the levels of danger or injury that may result if the product is
not used correctly as instructed.
The following symbols are used to indicate the type of instructions that need to be followed.
(The symbols given below are examples)
Do not pull the power cord
when carrying or storing the
product.
移動或存放時禁止拉扯電源線。
(Otherwise, the power cord may be
damaged with the possibility of fire or
electric shock.)
(否則電源線可能會損壞，導致火災或觸電。)
Do not damage the power cord
or power plug.
禁止損壞電源線或電源插頭。
Do not cut, modify, excessive distort,
twist, squeeze the power cord, and do
not place it near heat sources, place
heavy weight on it, etc.
禁止切割、改裝、過度扭曲、擰絞、擠壓電源線、
使電源線靠近熱源以及在電源線上壓放重物
等。
(Otherwise, the power cord may be
damaged with the possibility of fire or
electric shock.)
(否則電源線可能會損壞，導致火災或觸電。)
Do not let the product get wet.
禁止弄濕機體。
Do not place cups, etc. on the
product.
禁止在機體上放置水杯等。
(Otherwise, the product may
short circuit with the possibility
of fire or electric shock.)
(否則產品可能會短路，導致火災或觸電。)
Do not use power other than
the rated voltage .
禁止使用額定電壓以外的電源。
(Otherwise, the power cord may over-
heat and induce fire.)
(否則電源線可能會過熱，導致火災。)
Do not touch the power
plug with wet hands.
禁止用濕手接觸電源插頭。
(Otherwise, electric shock
may occur.)
(否則可能會導致觸電。)
請 務 必 遵 守
Please strictly follow
Those things shown in this column indicate
that there is possibility of causing death or
severe injury.
Those things shown in this column indicate
that there is possibility of causing minor injury
or damage to properties .
2
This product is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervi-
sion or instruction concerning use of the product by a person responsible for the safety.
Children should be supervised to ensure that they do not play with the product.
本產品不適合有殘疾、智障或精神障礙的人士或缺乏經驗、常識者（包括兒童）維護使用，除非在負責他們安全的人
士的看護或指導下使用。兒童應該有人進行看護，以防將產品當做玩具。
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
如果電源軟線損壞，為了避免危險，必須由製造商、其維修部或類似部門的專業人員更換。
Disconnect power supply before maintenance.
維護保養前先斷電。
警告WARNING
→
Do not disassemble or modify
the product.
禁止擅自拆開或改裝本產品。
(Otherwise, the product may catch
fire or malfunction, thus resulting in
fire or electric shock.)
(否則產品可能導致起火或運作異常，引發
火災或觸電。）
Contact the dealer for repair.
需要維修時請聯繫經銷商進行維修。
Do not insert your fingers, me-
tallic objects or others into the
air inlet, air outlet or gaps.
禁止將手指或金屬物等異物放入進風
口
、出風口或縫隙中。
(Otherwise, you may be hurt by the
inner units with the possibility of
electric shock or injury.)
(否則可能會接觸到產品內部，導致觸電或受
傷。)
安全注意事項
→
Clean the power plug
regularly.
請定期清潔電源插頭。
(If dust is found on the power plug,
insulation maybe damaged by humidity
and fire may occur.)
(如果電源插頭上有灰塵，濕氣可能會破壞
電源插頭的絕緣部分，導致火災。)
Disconnect the power plug and wipe it
with dry cloth.
拔出電源插頭，用乾布擦淨。
When the product will not be used
for a long period, disconnect the power
plug.
長期不使用產品時，應拔出電源插頭。
Insert the power plug
completely.
請將電源插頭完全插入電源插座。
(If the power plug is not fully inserted,
the power cord may be overheated,
thus resulting in fire or electric shock.)
(如果電源插頭沒有完全插牢，可能會使電源
線過熱導致火災或觸電。)
Do not use damaged power plug or
loosen power socket.
禁止使用已損壞的電源插頭或鬆動的電源插
座。
In case of any abnormality or
malfunction, stop using the
product immediately and
disconnect the power plug.
當有以下的任何情況出現時
，請立即
停止使用本產品並拔出電源插頭。
(Otherwise, electric shock, fire or
smoke may occur.)
(否則可能會導致觸電、起火或冒煙。)
<Examples of abnormality/
malfunction>
<異常·故障的例子>
The product stops operating when
moving the power cord.
移動電源線時，產品運轉停止。
If any switches do not work.
如果任何控制按鈕故障。
If the circuit breaker is tripped or when
fuse blows.
如果斷路器起作用或保險絲燒毀。
If the power cord or power plug
becomes abnormally hot.
如果電源線或電源插頭異常發熱。
If you notice a burning smell or an
abnormal sound or vibration.
如果您發覺有燒焦的異味或異常的聲音或振
動。
If there is any other abnormalities or
malfunction.
如果有其他任何異常現象或故障。
Please stop using the product immedi-
ately and disconnect the power plug,
and contact the dealer to check and
repair.
立即停止使 用，拔出電源插頭，聯繫經銷商進
行 檢 查、維 修。
請 務 必 遵 守
SAFETY PRECAUTIONS Please strictly follow
確
認
與
設
置
CONFIRMATION
AND SETUP
3
4
安全注意事項
→
注意CAUTION
Do not clean the product with
gasoline or other volatile mix-
ture solvents, and avoid con-
tacting with spray insecticides.
禁止使用汽油或其他揮發性混合溶劑
擦拭產品，以及把殺蟲劑噴到產品上。
(Otherwise, the product may crack or
short circuit with the possibility of injury,
fire or electric shock.)
(否則產品可能會破裂或短路，導致受傷、火災或
觸 電。）
Do not operate this product in
places where indoor fumigation
type insecticides are being used.
使用煙熏型殺蟲劑時禁止使用本產品。
(Chemical residue may build up inside
the product and discharge from the air
outlet, and cause damage to health.)
(否則化學殘留物可能會在產品內積聚，然後從
出風口排出，危害身體健康。）
Ventilate the room with fresh air thor-
oughly after using insecticides before
operating the product.
使用殺蟲劑後，應先讓房間徹底通風，然後才可
使用本產品。
Do not sit on or lean against
this product.
禁止坐、靠本產品。
(Otherwise, the product may fall over
and injury may occur or damage the
product.)
(否則產品可能會翻倒，導致受傷或產品損
壞。）
Families with children should pay more
attention.
有小孩的家庭要多加注意。
Do not place the product in
the following places.
禁止放置本產品於以下場所。
Incline and unstable place.
不平穩的場所。
(Otherwise, the product may fall over
and injury may occur or damage the
product.)
(否則產品可能會翻倒，導致受傷或產品損
壞。）
Where the temperature or humidity is
extremely high, or watery area, such as
bathroom.
浴室等高溫、高濕或會弄濕產品的場所。
(Otherwise, current may leak with the
possibility of fire or electric shock.)
(否則產品可能會漏電，導致火災或觸電。)
Where oil fume is emitted, such as
in kitchens.
廚房等排放油煙的場所。
(Otherwise, the product may crack and
injury may occur.)
(否則產品可能會破裂，導致受傷。）
Where oil or inflammable gas is present
and may be leaked.
使用油或可燃性氣體並可能出現洩漏的場所。
(Otherwise, a fire may occur due to
ignition in the product.)
(否則產品吸入後可能會起火，導致火災。)
Where the air outlet faces animals or
plants directly.
風口正對動植物的場所。
(Otherwise, it may cause discomfort to
the animals and dry out the plant.)
(否則可能會導致動物不適、植物風乾。）
Do not place the product near
combustible materials such as
lighted cigarette, incense, etc.
禁止將點燃的香煙、香火等可燃物接
近產品。
(Otherwise, these may be absorbed
into the product with possibility of fire.)
(否則產品吸入易燃物後可能會起火，導致火
災。)
When carrying the product,
please hold the left and right
handles, but not the louver or
front panel.
移動產品時請握住兩側把手，請勿握住
導風板或前面板。
(Otherwise, the product may fall off,
injury may occur.)
(否則產品可能會掉落，
導致受傷。）
When disconnecting the power
plug, hold the power plug
instead of the power cord.
請手持電源插頭部位拔出電源插頭。
(Otherwise, the power cord may be
damaged with the possibility of fire or
electric shock.)
(否則電源線可能會損壞，導致火災或觸電。)
請 務 必 遵 守
SAFETY PRECAUTIONS Please strictly follow
5
注意CAUTION
安全注意事項 請 務 必 遵 守
SAFETY PRECAUTIONS Please strictly follow
設置與使用要求
SETTING AND OPERATING REQUIREMENTS
Keep the room well-ventilated when using the product together with
a burner.
與燃燒器具一起使用時，需保持空氣流通。
(Otherwise, carbon monoxide poisoning may occur.)
(否則可能會導致一氧化碳中毒。)
This product cannot remove carbon monoxide.
本產品不能去除一氧化碳。
在這些場所使用，非常有效！
Area that can enhance the effectiveness!
Way to against PM2.5 and indoor dust, etc.
針對PM2.5、室內揚塵等
。
Way to circulate air more effectively.
使房間裡的空氣有效循環
。
Place the product with its left, right and top about 30 cm or more away from walls, furniture or
curtains, etc, otherwise, the pollutants are difficult to be cleared.
To ensure effectiveness of this product, keep its back at least 1 cm away from the wall.
請將本產品設置在其左右與上方距離牆壁、傢俱、窗簾等約30 cm以上的地方，否則污染物難以被吸入機體。
為了更有效地使用本產品，請保持產品背部距離牆壁至少1 cm。
If the product is used in the same place for a long period.
在同一場所長時間使用時。
It may result in dirty surrounding walls or floor. We recommend that you move the product away
from where it is placed when maintaining it.
產品周圍的牆壁及地板會有髒污，進行產品維護保養時，建議改變設置場所。
Since PM2.5, dust, etc are likely to float in the air near the floor,
we recommend you to place the product on flat floor in the room.
由於PM2.5、灰塵等容易落到地板附近，因此建議將本產品設置在房間平坦的地面上。
確
認
與
設
置
CONFIRMATION
AND SETUP
→
Do not use the same power socket with TV, radio, etc.
請勿與電視機、收音機等設備使用同一電源插座。
(Otherwise, visual disturbances or noises may be caused.)
(電源插頭插入時有可能會產生影像紊亂以及雜音。)
In this case, insert the power plug into another power socket.
請將電源插頭插到其他電源插座上。
請勿在產品進風口和出風口處放置障礙物。
（否則可能會影響產品性能。）
Do not place obstacles on the product air inlet and outlet.
(Otherwise it may affect product performance.)
室內微塵捕捉器徹底清除地面低層空氣中的灰塵
配備nanoe® X技術
通過Econavi模式，省電運轉
採用“室內微塵捕捉器”和“nanoe® X”技術，
締造清淨家居。
“House Dust Catcher” and “nanoe® X”
give you clean and fresh air.
House Dust Catcher completely cleaning dust from the air near
the floor
Equipped with nanoe® X technology
Low power consumption in the Econavi mode
6
→
Do not set the product in the following places.
請勿設置本產品於以下場所。
Where the product will be exposed directly to sunlight, outlet air of air conditioner or heat, etc.
陽光直射、被空調吹到或受熱等場所。
(Otherwise, deformation, degeneration, discolor or malfunction may be occurred.)
(否則可能會造成變形、老化、變色或故障。)
Near equipment such as TV and radio.
電視機及收音機等設備附近。
(Otherwise, visual disturbances or noises may be caused.)
(否則可能會導致影像紊亂以及雜音。）
Keep the product 1 m or above away from such devices.
請距離1 m以上設置。
設置與使用要求
SETTING AND OPERATING REQUIREMENTS
產品特點
PRODUCT FEATURES
請勿在產品上放置物品。
(否則產品可能會誤動作或故障。）
Do not place any object on the product.
(Otherwise, an operation error or malfunction may be caused.)
7
確
認
與
設
置
CONFIRMATION
AND SETUP
關於nanoe® X
所謂nanoe® X，是通過施加高電壓來分離水分子而產生的帶電淨水粒子。
注：nanoe®和nanoe®標記為松下控股株式會社的注冊商標。
nanoe® X特點：水分含量多、顆粒小、穩定性高等。
上述特點均經過SGS通標標準技術服務有限公司檢測。
弱酸性（具有與髮質和皮膚接近的弱酸性特性）。
OH自由基多(每秒產生OH自由基達48000億個)。
nanoe® X 是含有nanoe®10倍量的OH自由基的微粒子離子。
nanoe® X are particulate ions containing hydroxyl radicals whose amount is 10 times that
of nanoe®.
The so-called nanoe® X are charged water purification particles
generated by applying high voltage to separate water molecules.
4. More hydroxyl radicals (up to 4,800 billion of radicals are generated per second).
5. Weak acidity (with weak acidity features close to that of hair and skin).
About nanoe®
X
Note: nanoe® and the nanoe® mark are registered trademarks of Panasonic Holdings Corporation.
nanoe® X features: high moisture content, small particles,
high stability, etc.
水分含量多（水分含量為一般負離子的含水量的1000倍 ）。
1. High moisture content (the moisture content is 1,000 times the
moisture content of ordinary anions).
顆粒小（大小約為5 nm~20 nm(納米)，可滲透到纖維及角質層深處）。
2. Small particles (about 5 nm - 20 nm (nanometers) in size, able to penetrate deep into the fiber
and stratum corneum).
穩定性高（比一般負離子穩定性高6倍，覆蓋距離高達10 m以 上 ）。
3. High stability (6 times more stable than a common ion, covering a distance of 10 m
or above).
All of the above features have been tested by SGS-CSTC Standards Technical Services Co., Ltd.
產品特點
PRODUCT FEATURES
過濾網更換指示燈
過濾網更換指示燈
Filter replacement
indicator
運轉關/開按鈕
PM2.5按鈕/指示燈
Power Off/On
button
PM2.5 button/
indicator
Child lock button/
indicator
Air volume button/
indicator
定時按鈕/指示燈
Timer button/
indicator
兒童安全鎖按鈕/指示燈 風量按鈕/指示燈
光度感應器
光度感應器
智慧節能按鈕/指示燈
Econavi button/
indicator
PM2.5 pollution
indicator
PM2.5污染度指示燈
PM2.5污染度指示燈
Light sensor
Control panel Air outlet (nanoe® X emission outlet)
Odor sensor
Power cord
Power plug
Handle
(left and right)
Front panel
Dirt sensor
Air inlet
(both sides)
Air inlet
(front)
Front
Control panel
Back
主要部件名稱
MAIN PARTS IDENTIFICATION
正面 背面
操作面板
操作面板
把手(左右）
進風口(兩側）
電源線
電源插頭
前面板
灰塵感應器
Louver
Clean sign
導風板
空氣污染度
指示燈
空氣污染度指示燈
進風口
（正面）
出風口(nanoe® X出風口)
異味感應器
nanoe® X指示燈
nanoe® X indicator
灰塵感應器與異味感應器
Dirt sensor and Odor sensor
Filter replacement indicator
Dirt sensor can detect air pollutants such as
PM2.5(0.7~2.5 µm particles), etc.
Odor senor can detect odor such as smoke, etc.
The sensitivity of sensor can be adjusted. (P.17)
灰塵感應器能檢測PM2.5(0.7~2.5µm大小的懸浮顆
粒)等空氣污染物。異味感應器能檢測煙味等異味。
感應器靈敏度可調節。(第17頁)
Clean sign
Blue: indicates clean
藍色：表示乾淨
Red (small): indicates slight dirty
紅色(小)：表示有點髒
Red (large): indicates dirty
紅色(大)：表示髒
Show the air pollution levels detected by dirt
sensor and odor sensor. The clean sign can be
turned off. (P.18)
顯示灰塵感應器與異味感應器檢測的空氣污染程度。
空氣污染度指示燈能關閉。(第18頁)
The indicator lights on indicates you need
to replace HEPA composite filter. (P.15)
指示燈亮起表示需更換HEPA多功能過濾網。
(第15頁)
PM2.5 pollution indicator
The indicator lights on indicates PM2.5 pollu-
tion reaches a certain level. You can use PM2.5
mode at this moment to remove PM2.5 quickly.
(P.12)
指示燈亮起表示PM2.5污染程度達到一定等級。此時可
使用PM2.5模式快速去除PM2.5。(第12頁)
The indicator lights on indicates nanoe® X is
being generated. nanoe® X will be generated
in all operation modes except you switch off
it. ( P.15)
指示燈亮起提示正在產生nanoe® X。在所有運轉
模式下都會產生nanoe® X，除非關閉nanoe® X功能。
(第15頁)
nanoe® X指示燈nanoe® X indicator
Light sensor
Detects the indoor brightness by the light
sensor, the product can automatically adjust the
brightness of indicators and the air volume.
After you go to bed, it becomes dark in the
room, then the product will switch to the “Sleep
Mode Auto Operation”. (P.18)
通過光度感應器檢測室內亮度，產品能自動調節指示燈
的亮度及風量。就寢時，室內變暗，產品進入“睡眠自動
運轉”。(第18頁)
8
設置
Remove the front panel.
Toggle the filter hook upward, and remove filters
(2 types).
Remove the deodorizing
filter from the poly bag.
Please don’t remove the black net
of deodorizing filter.
Poly bag
Deodorizing filter
(wrap in black net)
Front panel
Pull it forward
with both hands
前面板
開機準備
填寫開始使用日期。
設置產品前請務必閱讀第2~6頁。
安裝過濾網
從塑膠袋中取出脫臭過濾網。
從塑膠袋中取出脫臭過濾網。
拆下前面板。
向上撥過濾網鈎，拆下過濾網(2種 )。
雙手向前拉出
Pull it forward
with both hands
雙手向前拉出
過濾網鈎
上撥
脫臭過濾網
（被黑色的護網覆蓋著）
請勿取下脫臭過濾網上黑色的護網。
塑膠袋
SETUP
Before startup
Fill in the label
with the first
date of use.
Remove the deodorizing filter
from the poly bag.
Install filters
HEPA composite filter
Filter hook
Up
HEPA多功能過濾網
確
認
與
設
置
CONFIRMATION
AND SETUP
9
提示事項
Notice
提示事項
Notice
Make sure to read page 2~6 before
setting up the product.
Toggle the filter hook downward,
and secure filters.
Deodorizing filter
Filter hook
Down
安裝過濾網
向下撥過濾網鈎，固定過濾網。
過濾網鈎
下撥
使鉤爪與產品上的凹槽(2處)咬合。
脫臭過濾網
將黑面(正面)朝外，放入機體的凹部。
機體的凹部
安裝過濾網(2種)和前面板。
安裝脫臭過濾網。(無內外、上下
的區分）
安裝HEPA多功能過濾網。(有內外的
區分、無上下的區分）
安裝前面板。
將前面板的突起處插入產品上的
小孔(2處)，並且向下按到底。
使用前請務必安裝好前面板。
接通電源
插入電源插頭。
因為異味感應器以插入電源插頭
時的空氣潔淨度作為基準，所以
建議當室內空氣清潔時（如沒有
煙味時），插入電源插頭。
(異味感應器的基準會根據室內
的空氣清潔度自動更新。）
設置
SETUP
Install filters Power-on
Be sure to install front panel
before use.
Install the filters (2 types) and front
panel.
Connect the
power plug.
Install deodorizing filter.
(There is no distinction
between inside and outside,
upper and lower)
Install HEPA composite filter.
(There is distinction between
inside and outside, no distinction
between upper and lower)
Install front panel.
Fit the clutch into the indentation
(2 places) of product.
4
When inserting the power
plug, as the odor sensor uses
the degree of cleanliness at
this time as the standard, we
recommend that you plug it in
when the air is fresh (when
there is no cigarette smoke).
(The standard of the odor
sensor automatically updates
itself according to the degree
of the indoor cleanliness.)
Push in the protrusion into the
holes (2 places) of product and
press properly.
HEPA composite filter
With the black side (front side)
outward, fit it into the concave
part of product.
Concave part
of product
HEPA多功能過濾網
10
Press button, then
the clean sign blinks for
about 5 seconds.
按下 按鈕，空氣污染
度指示燈閃爍約5秒。
提示事項
Notice
使用方法
開始或停止運轉。
OPERATION
Press the button again, the product stops operating.
Turn on or off the product.
Press the button to operate.
The product operates in auto air volume mode when it is used for the first time,
then operates in the last mode when it was stopped.
Power Off/On 運轉關/開
再次按下此按鈕，產品停止運轉。
按下按鈕產品開始運轉。
初次運轉時以自動風量模式運轉，之後以上次停止時的模式運轉。
每按一下，指示燈將按下圖順序進行切換。
風量
根據感應器檢測的空氣污染程度，自動調節風量，
利用最佳的風量淨化空氣。
快速淨化空氣。
以中等速度淨化空氣。
低速安靜地淨化空氣。
（指示燈點亮）
選擇合適的風量淨化空氣。
(Indicator lights on)
Purify air quickly.
Purify air in medium speed.
Purify air quietly in low speed.
Select appropriate air volume for purifying air.
The indicator will be changed sequentially as figure below.
Automatically adjust the air volume according to the
air pollution detected by sensor, and use appropriate
air volume to purify air.
Air volume
11
使
用
方
法
OPERATION
運轉關/開按鈕
PM2.5按鈕/指示燈
Power Off/On
button
PM2.5 button/
indicator
Child lock button/
indicator
Air volume button/
indicator
定時按鈕/指示燈
Timer button/
indicator
兒童安全鎖按鈕/指示燈 風量按鈕/指示燈
智慧節能按鈕/指示燈
Econavi button/
indicator
當 指示燈亮起時，可按此按鈕快速去除PM2.5，直到 指示燈熄滅。
(此時PM2.5模式將停止，并跳轉到之前的模式運轉。)但是，當 指示燈未亮起時
按下此按鈕，PM2.5模式將運轉1分鐘后停止，并跳轉到之前的模式運轉。
Indicator
lights off
每按一下，指示燈將按下圖順序進行切換。
指示燈熄滅
定時2小時
定時4小時
取消定時
2小時后自動停止運轉。
4小時后自動停止運轉。
空氣污染度指示燈及風量指示燈熄滅，操作面板上指示燈變暗，
并以低速運轉，8小時后自動停止運轉。
The indicator will be changed sequentially as figure below.
Timer operation.
使用方法
OPERATION
定時運轉。
定時
Timer
(Indicator
lights on)
Smart power-saving mode.
Remove PM2.5 quickly.
Press the button again to cancel. ( indicator lights off)
(Can also be canceled by pressing button)
Press the button again to cancel.
( indicator lights off)
When operates in PM2.5 mode, timer
cannot be set.
智慧節能
省電智能運轉。
快速去除PM2.5。
按下按鈕將以智慧節能模式進行運轉。智慧節能是由“偵測模式”與“學習模式”組合而成
的省電智能運轉模式，並能自動調節風量。（第16頁)
（指示燈點亮） 再次按下此按鈕取消。( 指示燈熄滅）(也可通過按 按鈕進行取消)
再次按下此按鈕取消。
( 指示燈熄滅）
當以PM2.5模式運轉時，不能進行定時設置。
Econavi
Press the button will operate in Econavi mode. Econavi is a smart power-saving
operation combined by the “patrol mode” and “learning mode”, and it adjusts
the air volume automatically. (P.16)
(Indicator
lights on)
（指示燈點亮）
PM2.5 PM2.5
2 hours timer
The product will stop operating after 2 hours.
4 hours timer
The product will stop operating after 4 hours.
Cancel timer
定時8小時(睡眠模式)8 hours timer (sleep mode)
Clean sign and air volume indicator light off, indicators on
control panel dim, and the product operates at low speed,
then stops operating after 8 hours.
12
When indicator is on, you can press the button to remove PM2.5 quickly,
until the indicator lights off. (At this moment the PM2.5 mode will stop,
then product will switch to the previous mode and continue.) But, If you press the
button when indicator is off, the PM2.5 mode only will operate in 1 min,
then product will switch to the previous mode and continue.
提示事項
Notice
使用方法
OPERATION
(Indicator lights on)
(Long press 3 sec)
Long press the button for 3 seconds, then the child lock is set. With this
setting, other buttons are disabled when you press them, with sound “BI-BI-”.
To prevent child from wrong operating.
If power failure occurs when product is operating, the product will restart automatically when power
on again, and operate in the mode when power failure.
Long press the button for 3 seconds again to cancel.
( indicator lights off)
長按此按鈕3秒，完成設置。設置後，按此按鈕以外的其他按鈕將無法操作，並發出
“BI-BI-”的提示音。
再次長按3秒取消設置。( 指示燈熄滅）
（長按3秒）
防止兒童誤操作。
（指示燈點亮）
兒童安全鎖Child lock
前面板及過濾網的拆卸及安裝方法見第9~10頁。
提示事項
如果產品運轉時斷電了，當 再次來電時，產品將自動重啟并以斷電時的模式進行運轉。
運轉過程中，請勿用手搖動導風板。(否則角度及活動範圍會發生變化。)
→已搖動時，請立即停止運轉。(重新啟動后，將恢復到正常狀態。)
Notice
維護保養
MAINTENANCE
Do not use the detergents shown below.
For installation and removal methods of front
panel and filters, please read P.9~10.
When cleaning, do not leave the removed parts
unattended.
(Otherwise, it may cause tripping or damage.)
Do not operate the product when the HEPA
composite filter is removed.
(Dust will be inhaled into product inner parts,
and causes the product breakdown. The HEPA
composite filter cannot function while it is
removed.)
Do not operate the product when the deodoriz-
ing filter is removed.
(The deodorizing filter cannot function while it
is removed.)
When using chemically treated cloth, be sure
to follow the instructions carefully.
Make sure to disconnect the
power plug before cleaning
the product.
維護保養產品前
，請務必拔出電源插頭。
(Otherwise, the product might operate
with the possibility of electric shock or
injury.)
(否則產品可能會突然運轉，導致觸電或受傷。)
WARNING 警告
進行維護時，請勿隨意擺放拆卸的零件。
(否則可能會絆倒路人或造成零件損壞。)
HEPA多功能過濾網未安裝時，請勿使用本產品。
(將失去除塵效果，灰塵進入產品內將造成故障。)
脫臭過濾網未安裝時，請勿使用本產品。
(將失去脫臭效果。)
請勿使用如下所示的洗滌劑。
Polish
Alkaline
detergent
Thinner
Bleach
Kerosene
Alcohol
磨
光
劑
鹼
性
清
潔
劑
稀
釋
劑
漂
白
水
酒
精
或
煤
油
使用經過化學處理的抹布時，請務必按說明操作。
Do not shake the louver with hands during operation.
(Otherwise, the angle and action range may change accordingly.)
→Please stop operating the product immediately if it is shaken.
(The product will restore to the normal status after it restarts.)
使
用
方
法
維
護
保
養
OPERATION MAINTENANCE
13
提示事項
Notice
維護保養
MAINTENANCE
清潔方法
Cleaning method
脫臭過濾網
周圍附著塵埃時，請用吸塵器等去除。
請勿水洗。
Deodorizing filter
When there is dust around the deodorizing
filter, remove the dust with a vacuum
cleaner, etc.
Do not wash the filter with water.
用吸塵器等去除黑面(正面)的灰塵
請勿用力按壓，否則過濾網可能會受損。
白面(背面)無需進行
維護保養。
請勿水洗。
毛刷吸嘴或縫隙吸嘴
墊上報紙等物品,以免灰塵弄髒地面。
Clean the black side (front side)
with a vacuum cleaner, etc.
HEPA composite filter
< about once every 2 weeks >
Dusting brush nozzle
or gap suction nozzle
Lay with newspapers, etc
to avoid dust messing floor.
Do not wash the
filter with water.
Please do not punch too much, otherwise
the filter may be damaged.
Maintenance is unnecessary for the white
side (back side).
HEPA多功能過濾網 <約2周1次>
使用充分擰乾的軟布擦拭污垢
請勿使用粗布擦拭或過度用力擦拭，否則會損傷
表面。
請使用乾布擦拭電源插頭。
鏡片(左上方）
乾棉棒
用乾棉棒去除鏡片上的污垢
拆下灰塵感應器外殼，如下圖。
使用如圖所示的乾棉棒進行擦拭。
Wipe off any dust and dirt using
a well wrung-out cloth
Body and front panel
< about once a month >
Do not wipe it with a hard cloth or hardly.
Otherwise, the surface may be damaged.
Wipe the power plug with a dry cloth.
前面板及機體<約每月1次>
Lens(top left)
Dry cotton swab
Wipe the dirt off the lens with a dry
cotton swab
Dirt sensor
< about once every 3 months >
Remove the external cover of dirt sensor as
shown below.
Wipe the lens with a dry cotton swab as
shown below.
灰塵感應器 <約3個月1次>
Wipe the lens periodically.
(The sensor may not function normally with
accumulation of moisture and smoke from
cigarette.)
定期擦拭鏡片。（帶有濕氣以及被香煙的煙油污染
後，有可能無法進行正常感應。）
Do not insert a cotton swab in other parts.
請勿將乾棉棒插入到鏡片以外的其他部位。
Be sure to disconnect the power before
cleaning.
請務必在拔出電源插頭的狀態下進行操作。
You can use a light in order to see lens
clearly.
看不清楚鏡片時可用燈光照射。
14
維護保養
MAINTENANCE
更換過濾網
HEPA多功能過濾網 脫臭過濾網
更換週期
條件
過濾網更換指示燈亮起時(約10年1次)
每天吸入6支香煙時
(日本電機工業會標準JEM1467)
When the product inhales the smoke of six
cigarettes every day. (Japan Electrical
Manufacturers’ Association JEM1467)
Conditions
When the filter replacement indicator lights
on. (About once every 10 years)
Replacement
period
(Optional accessories: back cover)
HEPA composite filter Deodorizing filter （自選配件：末頁）
即使清潔乾淨，達到更換週期的過濾網也不可再被使用，請將它作為不可燃垃圾處理。
The filter which needs to exchange cannot be used again even it is cleaned, please dispose it as
non-flammable garbage.
Filter replacement
After replacement, please connect power plug, then press and buttons at the same
time for about 3 seconds until the filter replacement indicator turns off, then the reset is completed.
更換過濾網後，請插入電源插頭，同時按住 和 按鈕約3秒，過濾網更換指示燈熄滅則重置完成。
Fill in installation date on the label in filter case, then stick it on product to cover the old date. (P.9)
請在過濾網包裝箱中的標籤上記錄開始使用日期，並粘貼在機體上，覆蓋舊的使用日期。(第9頁)
Filter replacement period may be
shorten, depending on the environ-
ment (such as where smoking is
frequent).
Please replace it when ineffective.
根據使用場所等實際情況(如吸煙人數較多
的家庭)，過濾網的更換週期可能會縮短，當
過濾效果不好時請及時更換。
※
※
※
長期閒置時
When idle for a long time
Disconnect power after turning off the product. (The product still consumes power even at rest.)
停止運轉產品並拔出電源插頭。（因為停止工作時也耗電。）
Maintain the product as usual.
需進行維護保養。
Put the product into poly bag and carton, and keep it in a dry place.
(If you overturn it or keep it flat, product malfunctions may occur.)
放入塑膠袋和紙箱中，並存放於乾爽處。（倒置或平放可能會導致產品發生故障。）
關於nanoe® X
更多信息
FURTHER INFORMATION
About nanoe® X
During operation, press and buttons at the same time for about 3 seconds
(nanoe® X indicator lights off). Press the buttons for about 3 seconds again to restart the nanoe® X.
(nanoe® X cannot be set during product stops operating.)
nanoe® X can be switched off. nanoe® X功能可關閉。
在產品運轉狀態下，同時按下 和 按 鈕約3秒(nanoe® X指示燈熄滅)。
再次按下約3秒，可重新開啟nanoe® X功能。(產品停止運轉狀態下，nanoe® X功能不能設置。)
維
護
保
養
其
他
信
息
MAINTENANCE OTHER
INFORMATION
15
提示事項
Notice
如果在有芳香劑、香煙或烤肉等氣味濃烈的環境下(特別是酒店)使用，異味有可能會附著在過濾網上。當過濾網
的吸附能力達到飽和後，氣味也會因吸附過盈而隨風再次被吹出。當發生以上情況時，請對HEPA多功能過濾網進
行維護保養；若保養後仍有異味吹出，即使過濾網更換指示燈沒有亮起，也請對HEPA多功能過濾網和脫臭過濾網
進行更換。另外，若經常在氣味濃烈的環境下使用，建議定期針對室內開窗進行通風換氣。
If the product is used in a room (especially hotel) with strong odor such as aromatic smell,
cigarette smoke or barbecue smell, these odors may adhere to the filter. When the adsorption
capacity of filter reaches saturation, odor will also be blown out again with the wind because of
excess adsorption. When there is above situation, please clean the HEPA composite filter. If the
situation persists, please replace the HEPA composite filter and deodorizing filter, even if the filter
replacement indicator is off. In addition, if often used in a room with strong odor, please open the
windows to ventilate the room regularly.
After replacement, please connect power plug, then press and buttons at the same
time for about 3 seconds until the filter replacement indicator turns off, then the reset is completed.
更換過濾網後，請插入電源插頭，同時按住 和 按鈕約3秒，過濾網更換指示燈熄滅則重置完成。
Fill in installation date on the label in filter case, then stick it on product to cover the old date. (P.9)
請在過濾網包裝箱中的標籤上記錄開始使用日期，並粘貼在機體上，覆蓋舊的使用日期。(第9頁)
更多信息
關於HEPA多功能過濾網
nanoe® X產生的環境條件
利用室內空氣產生，根據溫度和濕度的不同，有時可能無法穩定產生。
室內溫度：約5 ℃～35 ℃（露點溫度：2 ℃以上） 相對濕度：約30%～85%
產生nanoe® X的同時，也會產生微量臭氧。但其產生量遠遠不及森林等自然界存在的臭氧量，不會對人體造成傷害。
FURTHER INFORMATION
Room temperature: about 5 ℃～35 ℃ (dew-point temperature: 2 ℃ or above)
Conditions for nanoe® X generation
Relative humidity: about 30%～85%
nanoe® X is generated by using the air in the room. Therefore, due to the differences in temperature
and humidity nanoe® X may not be generated stably.
When nanoe® X is generated, small amount of ozone will be released. However, the quantity will be
far less than the level in natural environment such as forest, and not be harmful to human beings.
HEPA多功能過濾網中集成了生物除菌、抗過敏原，能夠抑制過敏原（花粉、螨蟲屍體及糞便）、細菌、黴菌。
HEPA多功能過濾網會散發出“綠茶兒茶素”、“生物除菌”以及“抗過敏原”特有的氣味，此氣味對人體無害。
抗過敏原：抑制過敏原（花粉、螨蟲屍體及糞便）的活動。
Super Allergy-buster: inhibits the activity of allergic substances (pollen, dead mites and feces).
The HEPA composite filter which with the Bio-sterilization and Super Allergy-buster can inhibit
allergens (pollen, dead mites and feces), bacteria, mold.
Testing authority: Osaka Municipal Technical Research Institute 檢測機構：大阪市立工業研究所
Test method: check the decrease of refined house dust mite allergen, by using enzyme immune
measuring method.
檢測方法：通過酶免疫測定法，確認精製塵螨應變原的降低。
Inhibiting method: contact with Super Allergy-buster 去除方法：與抗過敏原接觸
Target: allergens trapped by the filter (mites, pollen) 檢測對象：過濾網收集的過敏原（螨蟲、花粉）
Test result: inhibited 99% and above. (Daikou research report No. 2127)
檢測結果：抑制99%以上。（大工研報第2127號）
The HEPA composite filter might emit unique and harmless smell of “Green Tea Catechin”,
”Bio-sterilization” and “Super Allergy-buster”.
About HEPA composite filter
About Econavi 關於智慧節能
Econavi mode refers to the automatic operation combined by the “patrol mode” in which the product
detects the dirt in the air in the room every hour and the “learning mode” in which the product can
forecast the dirt generation by mastering the generation time of dirt every day.
Automatically stops operating when the clean air is detected, meanwhile it also operates in advance
to eliminate the dirt effectively before spreading, thus reducing the operation time and saving power.
智慧節能是指每小時檢測房間內空氣污染物的“偵測模式”和通過掌握每天污染物產生時間的規律，在污染擴大之前先
行運轉產品的“學習模式”共同組合而成的自動運轉。
檢測到空氣潔淨時，自動停止運轉，同時通過先行運轉，在污染擴大前進行有效去除從而縮短執行時間節省電力。
Patrol mode
Learning mode
偵測模式
學習模式
The product will stop operating automatically after the air is cleaned.
After the operation is paused for 50 min,the product will operate for 10
min with air volume set to “Med” in the patrol mode. While the opera-
tion is paused in the patrol mode, the product will operate with the
suitable air volume corresponding to the dirtiness detected.
空氣變潔淨後會自動停止運轉。運轉中止50分鐘後，以中速風量運轉10分鐘偵測模
式。在運轉中止及偵測模式期間，若檢測到污垢時將以最佳的風量進行運轉。
The product records the time and dirtiness of air during operation, and takes the preventive opera-
tion 5 min before the recorded dirt is generated in the next day.
(Although the records are updated every day, the previous records will be lost once the power plug is
disconnected.)
記錄運轉過程中空氣污濁的時間段以及污濁程度，次日將在所記錄的污濁產生時間前5分鐘進行預防運轉。
(記錄每日更新，但是拔出電源插頭後之前的記錄會全部消除。)
16
Removes 99.97%* of 0.3 µm particles.
*it’s dust removing performance of filter itself, the effect in the entire room is not same.
粒徑0.3 µm顆粒物的去除率達到99.97%*。
*這是過濾網的去除性能。與整個房間的去除性能不同。
Test No.: KJ20222780 檢測報告號： KJ20222780
Test Standard: JIS B 9908: 2011 Test method of air filter units for ventilation and electric air cleaners
for ventilation
檢測標準： JIS B 9908: 2011 換氣用空氣過濾網組合·換氣用電氣集塵器的性能試驗方法
更多信息
FURTHER INFORMATION
關於異味感應器·灰塵感應器
空氣流動種類
檢測空氣污染物，通過指示燈顯示污染程度。在風量為自動時，根據空氣污染狀況自動調節風量淨化空氣。
感應器的靈敏度可調節。(出廠設置為“中感應度”)
產品停止運轉的狀態下，同時按下 和 按鈕約3秒，此時指示燈依次點亮。如下：
油煙、霧狀的水滴
感應器
異味感應器
灰塵感應器
感應範圍 有可能感應
香煙、香火、烹飪、寵物的氣味
化妝品、酒精、噴霧劑類等
煙（香煙、香火等的煙）
中感應度 高感應度 低感應度
PM2.5(0.7~2.5 µm大小的懸浮顆粒）
開關門時產生的風或急劇的溫度變化等
室內揚塵(灰塵、壁虱的屍體·排泄物、黴菌孢子、
花粉等)
蒸汽（水蒸汽）、油煙
達到所需設置模式時，請鬆開按鈕。
根據空氣污染狀況，導風板移動到最佳的位置淨化空氣。
The sensor can detect the pollution of the air, and show the pollution level by indicator. The
product can optimize the air volume automatically in auto operation according to the air quality.
The louver move to the best position according to the air quality to clean the air.
About odor sensor/dirt sensor
Type of airflow
Sensing scope
Odor sensor
Dirt sensor
Odor from cigarettes, incense, cooking, pets
Cosmetics, alcohol, sprays, etc.
PM2.5 (0.7~2.5 µm particles)
Humidity (water vapor), oil
Oil, fog-stated water drip
Indoor dust (dust, dead bodies and excreta
of ticks, mold spores, pollens, etc.)
Smog (cigarettes, incenses, etc.)
The wind generated when a door
is opened or closed, or sudden
temperature changes
May detect
Sensor
The sensor’s operation may vary depending on the indoor airflow condition if a heater is placed
near the product in a room.
在靠近加熱器的場所使用時因室內空氣的流動，感應器的工作狀況有可能會發生變化。
The sensor is not designed to detect bacteria and viruses.
不能夠感應細菌以及病毒。
Stop operating the product, then press and buttons at the same time for about
3 seconds. The indicator will light on in sequence as illustrated below.
The sensitivity of the sensor can be adjusted. (The default setting is “medium sensitivity” .)
Please release the buttons, when the
sensitivity is set as required.
Medium sensitivity High sensitivity Low sensitivity
Air quality
Air is clean
Odor, PM2.5 or smog is
detected
空氣污染狀況
空氣清潔
Blue Switch direction
藍色 擺動
圖解
Switch direction
擺動
向上
前方
Red
Upward
Front
紅色
檢測到異味、PM2.5或煙霧
House dust is detected
檢測到室內揚塵
Odor/PM2.5/smog and
house dust are detected
同時檢測到異味/PM2.5/煙霧
和室內揚塵
Clean sign FigureAction of louver
空氣污染度指示燈 導風板的動作
其
他
信
息
OTHER
INFORMATION
17
更多信息
FURTHER INFORMATION
達到所需設置模式時，請鬆開按鈕。
常見問題解答
諮詢或送去維修之前，請先確認以下情況。
為什麼吹出口發出“嘰”的聲音？ 為什麼運轉過程中空氣污染度指示燈熄滅？
為什麼空氣污染度指示燈不發生變化？
怎麼關閉空氣污染度指示燈？
Please confirm the following before you put questions forward or send the product for repair.
FAQ
Why is a “jee” sound from the
emission outlet? Why does the clean sign turn off
during operation?
Why does the clean sign remain
unchanged?
How to turn off the clean sign?
There is a slight sound when nanoe® X is
being generated. Depends on the
environment and operation mode, the
sound may be a bit loud or inaudible but
it is not abnormal.
產生nanoe® X時，將發出些許該聲音。根據使用
環境、運轉模式不同，聲音會大小有所不同，這並
非異常。
Such problems are easy to occur when
the sensitivity of the sensor is low.
You can adjust the sensor with a
specified sensitivity. (P.17)
感應器靈敏度比較低時容易出現此現象。
可調節感應器靈敏度。（第17頁）
Please press and buttons
at the same time for about 3 seconds
during operation.
在運轉過程中同時按下 和
按鈕約3秒 鐘。
Please press the buttons for about 3
seconds again to relight clean sign.
再次按此按鈕約3秒，可重新點亮空氣污染度
指示燈。
The product detects the indoor brightness,
and adjusts the brightness of the clean sign
automatically with the “Sleep Mode Auto
Operation” function. (P.18)
在“睡眠自動運轉”模式下，檢測室內亮度，自動調節
空氣污染度指示燈的亮度。（第18頁）
18
通過光度感應器檢測室內亮度，自動調節指示燈的亮度以及風量大小。 就寢時室內變暗，指示燈熄滅並以低速風量
運 轉。
風量設置為高速、中速或低速時，將不能自動調
節風量。
“睡眠自動運轉”模式可設置。(出廠設置為“睡眠自動1”)
Sleep Mode Auto 1
Sleep Mode
Auto 1
Sleep Mode
Auto 2
Sleep Mode Auto 2
No Sleep Mode Auto
No Sleep
Mode Auto
“Sleep Mode Auto Operation” can be adjusted. (The default setting is “Sleep Mode Auto 1” .)
Please release the buttons, when
the sensitivity is set as required.
About sleep mode auto operation
Light off
No change
Stop operating the product, then press and buttons at the same time for about 3
seconds. The indicator will light on in sequence as illustrated below.
產品停止運轉的狀態下，同時按下 和 按鈕約3秒，此時指示燈依次點亮。如下：
無睡眠自動
無睡眠自動
睡眠自動2
睡眠自動2
睡眠自動1
睡眠自動1
Indoor brightness
Control panel
Clean sign
Indicator
Dimness Dark
Mode
關於睡眠自動運轉
When the air volume is set to “Hi”, “Med”
or “Lo”, the air volume cannot adjust
automatically.
Detects the indoor brightness by the light sensor, and automatically adjusts the brightness of
indicators and the air volume. When sleeping, the room becomes dark, the indicators will be dimmed
or light off and the air volume becomes low.
模式 指示燈
微暗
燈不變
No change
燈不變
No change
燈不變
No change
燈不變
No change
燈不變
No change
燈不變
燈熄滅
暗
室內亮度
操作面板
空氣污染度指示燈
Control panel
Clean sign
操作面板
空氣污染度指示燈
Control panel
Clean sign
操作面板
空氣污染度指示燈
提示事項
Notice
Light low level
燈微亮
Light low level
燈微亮
Light low level
燈微亮
Light low level
燈微亮
Light low level
燈微亮
故障排除
即使是持續運轉，空氣污
染度指示燈一直為“紅色”
受到浴室等熱氣、噴霧產生的氣體影響，指示燈可能會變紅。
沙塵較多的場合。
灰塵感應器是否髒污？（第14頁）
The indicator may turn red when the product is subject to
steam in the bathroom or vapor emitting from sprayers.
When sand flies off.
Is the dirt sensor dirty? (P.14)
Possible situation
TROUBLESHOOTING
The clean sign remains red
even when the operation
continues
Please confirm the following
可能發生的狀況 請確認以下內容
自動運轉無法停止
空氣有污濁，但空氣污染
度指示燈顯示仍為“藍色”
難以去除空氣中的污物
出風量少
灰塵感應器是否髒污？（第14頁）
風量設置為自動時，即使室內空氣潔淨也會低速運轉。
請確認產品是否在污染物難以吸入機體或面積太大的場所使用？(第5頁、末頁)
HEPA多功能過濾網是否髒污？（第14頁）
維護保養後仍然無改善時，則更換新的過濾網。
機體、前面板、過濾網是否髒污？（第14頁）
如果清潔後仍無改善，則更換新的過濾網。(本產品不能去除香煙中的一氧化碳。)
在濃烈氣味的房間內使用過嗎？如果在有芳香劑、香煙、烤肉或濃烈氣味場
所中使用，可能會縮短過濾網的使用週期。
在這種環境下使用時，建議同時打開房間的換氣系統或適當開窗通風。若
維護保養後仍有異味吹出，即使過濾網更換指示燈沒有亮起也請更換HEPA
多功能過濾網和脫臭過濾網。
產品的氣味讓人感覺不適
When the setting of air volume is “Auto”, the product will still
operate with low air volume even if the air in the room is clean.
Is the dirt sensor dirty? (P.14)
按下 按鈕 時，導風板附件可能會聽到聲響，屬正常現象。
After pressing , you may hear some sound around the
louver. This is normal.
Is the product placed in area where polluted air is difficult to be
cleared or the room size is too large for the product?
(P.5, back cover)
Is the HEPA composite filter dirty? (P.14)
Please clean it. If the situation persists, replace the filter with a
new one.
The clean sign remains
blue even when the air is
dirty
Automatic operation
cannot be stopped
Polluted air is difficult
to be removed
The odor from the
product is unpleasant
Is the body, front panel or filter dirty? (P.14)
If the problem persists after the filter is cleaned, please replace it
with a new one. (The harmful carbon monoxide generated by
cigarette cannot be removed)
The air volume is small
Has the product ever been used in a room with strong odor?
If the product is used in a room with strong odor such as aromatic
smell, cigarette smoke or barbecue smell, the filter replacement
period may be shortened.
If you use the product in such environments, it is recommended to
open the air ventilation system or open the windows to ventilate the
room at the same time. If there is still strong odor to be blown out
after the maintenance , please replace the HEPA composite filter and
deodorizing filter, even if the filter replacement indicator does not
light on.
風量指示燈全部燈閃爍
如遇以下情況，請立即聯繫經銷商進行維修。
產品可能發生故障。
請拔出電源插頭，聯繫經銷商進行維修。
Product may be out of order.
Please disconnect the power and contact the dealer for repair.
If any of the following cases occur, please contact the dealer immediately for repair.
All the air volume
indicators are blinking
有響聲
There is sound
其
他
信
息
OTHER
INFORMATION
19
If a problem is encountered, please investigate it by going through the following items.
If the problem still persists, please disconnect the power plug and contact the dealer for repair.
首先請確認以下內容，執行此操作後仍無法修復時，請拔出電源插頭，聯繫經銷商進行維修。
更換用HEPA多功能過濾網 更換用脫臭過濾網
P1222-0 PV55H8950
Replacement HEPA composite filter Replacement deodorizing filter
Web Site: http://www.panasonic.com
Panasonic Corporation
© Panasonic Corporation 2022
規格
SPECIFICATIONS
電源線長度
產品尺寸
產品重量
※1
※2
注：本產品不能去除香煙中的一氧化碳。
寬度300 mm X [深度195 mm+(腳部：10 mm)] X 高度580 mm
Hi
49
5.3
11
2.0
2.0 m
5.8 kg
300 mm x [195 mm+(Foot:10 mm)] x 580 mm (WxDxH)
7
0.9
Med Lo
Up to 41 m2 in a standard household room
220 V~ 50 Hz
Model number
Power supply
Power cord length
Product dimension
Product weight
Air volume settings
Air volume (m3/min)
Power consumption (W) 1
Floor area capacity 2
Note: This product cannot remove hazardous substances such as carbon monoxide from the
cigarette smoke.
型號
額定電壓·頻率
風量模式
適用面積 普通家庭，最大適用面積41 m2
風量 (m3/min)
消耗功率（W）
※1
※2
The power consumption is about 0.3 W when the operation is set to “Off”.
(With the power plug inserted).
運轉狀態為“關”時的耗電量為0.3 W。（插上電源插頭的狀態）
Floor area capacity is based on JEM1467, under the condition of Hi speed.
(Japan Electrical Manufacturers’ Association)
適用面積依據JEM1467，在高速運轉的狀態下測定。(日本電機工業協會標準)
自選配件
OPTIONAL ACCESSORIES
風量指示燈閃爍。
產品可能發生故障。
請拔出電源插頭，聯繫經銷商進行維修。
出現下列情況時，請聯繫經銷商進行維修
All the air volume indicators are blinking.
Please contact dealer
Product may be out of order.
Please disconnect the power and contact the dealer for repair.
型 號：
Part No.:
型 號：
Part No.:
Issue date: 12/2022
發行日期：12/2022
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
