VANTRUE OnDash T2 ユーザーマニュアル

OnDash T2Dash Cam

www.vantrue.net/contact facebook.com/vantrue.live

f

Always a surprise in Vantrue

Hey, find us here:

- 1 -

1. What’s in the box?

Was ist in der Box?

Die Übersicht über Kamera

Vorbereitung vor dem Einschalten

Grundlegende Operation

Spezifikationen

Garantie und Unterstützung

3

2. Camera Overview 4

3. Getting Started 5

4. Basic Operation 9

5. Specifications 21

6. Warranty & Support 22

23

46

24

47

25

48

30

53

43

64

44

65

- 2 -

VERZEICHNIS

1. What’s in the box?

A. Dual Car Charger with Built-in

Mini USB Cable (10ft)

B. VANTRUE T2 Super Capacitor

Dash Cam

C. Suction Cup Mount

D. OBD Cable

E. USB Data Cafle (3ft)

F. User Manual

G.Quick Start Guide

H. Warranty Card

A

E

C

B

D

F G H

- 3 -

2. Camera Overview

NO. Name Description

1

2

3

4

Mount Connector

Lens

Speaker

Wave Guard Indicator

Connects to the Suction Cup Mount.

Facing Camera for video recording

road events.

Delivers sound during video playback.

Parking Monitor Indicator.

5

6

Wave Guard Indicator

On/Off button

Up Button

Turn on/off Wave Guard Indicator

Move selector up; rewind; Turn off LCD

screen.

7

8

Down Button

Menu Button

Move selector down; fast forward;

Microphone on/off.

Enter/exit setup menu.

9

10

LCD Screen

OK Button

2.0” TFT Color LCD Display.

Confirms the action; Stop/Start the

video recording.

- 4 -

1080P FULL HD

11 10 9

USB

13

14

17

15

16

5 6 7 812

1

3

4 2

18

19

12 Microphone Records clear audio with the video

footage.

14

15

AV OUT Port

13 Mini USB Port USB port for charging or transferring

data.

HDMI Port

AV OUT connects to external device.

For HDMI (High-Definition Multimedia

Interface) cable.

16 Reset Button

17 Micro SD Card Slot Provides expandable storage (up to

64GB in FAT32, Class 10).

19 DC Converter Box Protection of DC lines.

Press to force reset the device.

18 OBD Cable Connect the device with the car.

Screen overview

Please use a genuine Micro SD memory card from 16GB to 64GB

with a speed rating of class 10 or higher. Carefully insert the memory

card into the camera’s card slot until it clicks. To remove the card,

power off the camera first, then push the card into the slot until it

clicks again.

3. Getting Started

3.1. Installing a Memory Card

- 5 -

11 Snapshot/ Emergency

Button

Snapshot: Manually locks the currently

recording video clip following emergency

or to preserve important videos.

0

2018/05/03

00:00:23

003KM/H

05:00:53

1080FHD

3

Video Resolution

Snapshot

Emergency File Lock

Recording Standby Status

Recording

Loop Recording Time

Exposure

G-Sensor ON

Memory card

inserted or not

Current Date (YYYY/MM/DD)

and Time (24H)

MIC is ON

MIC is OFF

GPS Signal Locked

GPS Signal Connecting

Recording Time

(current clip)

Speed Unit

Time Lapse ON

Parking Mode On

Parking Mode OFF

HDR Mode ON

Wave Guard Indicator ON

Before using the card, please format it correctly using these steps:

-

Press MENU to enter setup; if the camera is recording video, press

Confirm button to stop the recording

-

Press the DOWN button to highlight the System Setup option, press

Confirm.

-

Press the DOWN button to highlight the Format option, press Confirm

followed by the DOWN button to select YES.

NOTE: Before using, please format your Micro SD card on the camera

first.

- 6 -

1. Attach the Suction Mount to the camera’s Mount Connector,

pushing it in until it clicks.

2. Thoroughly clean the windshield using water or alcohol, and wipe

clean with a dry cloth.

3. Wipe the Suction Mounting Pad clean on the Suction Mount.

4. Securely attach the Suction Mount to the windshield, and rotate

the locking clamp on the mount 90°upward until it clicks.

3.2 Installing the camera onto your windshield

1080P FULL HD

1. Carefully route the power cable around the windscreen and

tuck it under the trim.

2. With the Mini USB Cable, connect the supplied Car Charger

to the Camera Mount Base.

A. With the car charger cable

3.3 Power the camera

- 7 -

1080P FULL HD

vehicle’s cigarette

lighter port

3. Insert the Car Charger into your vehicle’s cigarette lighter port.

- 8 -

1. Carefully route the power cable around the windscreen and

tuck it under the trim.

2. Paste the DC converter box of OBD cable near the device.

B. With the OBD cable

1080P FULL HD

1. Once the power of the vehicle is on, the camera automatically

turns on.

2. If you disconnect with the power, the camera turns off.

4.1 Power ON/OFF.

A. Power with car charger.

The camera keeps on all the time until the Under Voltage

Protection system detects your car battery in low power status

(car battery power output is under 11.5V).

B. Power with OBD plug.

4. Basic Operation

- 9 -

3. Connect the micro USB port of OBD cable to the to the Micro

USB of Camera Mount Base.

4. Plug the OBD cable to the OBD socket of your car.

Attention: The location of most cars’ OBD port is in area as picture

shows.

1080P FULL HD

4.2 Menu Settings

After powering ON the camera, press the MENU button

to enter the setup process.

(If the camera is recording video, press the OK button to

stop recording before pressing the MENU button.)

Note: the Under Voltage Protection only works with 12V

vehicles, doesn’t work with 24V vehicles (usually trucks).

- 10 -

Press the DOWN button and highlight the Record Setup option.

Press the OK button to enter the settings, and use the UP/DOWN

buttons to navigate the different options.

-Resolution: 1920x1080 (30fps) or 1280x720(30fps). Options are

available.

-Loop Recording: This is set to 3minutes per video clip. Press OK to

change the duration: OFF, 1,3 or 5.

-G-Sensor: Set to Medium by default. Pressing OK gives the following

sensitivity options: Off, Low, Medium, High.

-Audio Recording: Default is ON. Press OK and DOWN button to

toggle it OFF/ON.

-Parking Monitor: Set to Far by default. Pressing OK gives the following

distance options: Far, Middle or Near.

-Exposure: Default is 0. Pressing OK gives the following options: +2.0,

+1.0, +.0, -1.0

A. RECORD SETUP

Record Setup System Setup

GPS Setup

Files

- 11 -

-Language: Default is English. Press OK to select between English,

French, Spanish, German, Italian, Simplified Chinese and Japanese.

-Format SD Card: Press OK, navigate DOWN and select OK to format

the micro SD card.

-Time & Date: Press UP/DOWN and OK button to set the current

date and time. Press the MENU button to exit.

-Auto LCD Off: Default is 3 MIN to turn OFF the camera 3 minutes

after recording commences. Press the OK button to select the

duration in minutes: OFF, 30 Sec or 3 Min.

-Wave Guard Indicator: Press OK and DOWN button to toggle it

OFF/ON.

-Device Sound: Default is ON. Press the OK button to toggle it ON/OFF.

-Frequency: Default is 50Hz. Press OK to toggle between 50Hz/60Hz.

-System Info: Press OK to check the current firmware version.

-Default Setting: Press OK and select OK to reset the device back

to stock factory settings.Press the MENU button to exit and complete

the setup.

-Car Number Set: Press UP/DOWN and OK to set your car license

number.

-Stamp: Default is ON. Press OK to toggle it OFF/ON. Stamp shows

the date/time, logo, car number, Speed and GPS Location

information.

-Rotate Display: Default is OFF. Press OK and DOWN button to toggle

it OFF/ON.

-Time Lapse: Default is OFF. Press DOWN followed by OK to set time

interval: Off, 1 Sec, 5 Sec or 10 Sec.

-HDR: Default is ON. Press OK and DOWN button to toggle it OFF/ON.

-Stamp: Default is ON. Press OK to toggle it OFF/ON. Stamp shows

the date/time, logo, car number, Speed and GPS Location

information.

B. SYSTEM SETUP

Note: To use the GPS function requires the purchase of an extra

GPS mount for the camera.

-GPS Setup: Default is ON. Press OK to toggle it ON/OFF.

C. GPS SETUP

4.3 Set Date/Time

Open the MENU interface, navigate to“SYSTEM SETUP”►

“Time & Date”, and press the OK button to set the date/

time. Navigate UP or DOWN to select date and time values.

Press OK to confirm and proceed. To finish setup, just press

the MENU button to exit.

Note: Date format is DD/MM/YY with the time in 24 hour

format.

- 12 -

After inserting a memory card, the camera will (by default)

immediately start loop recording video when connected to a

power source and powered ON. If the device is not connected

4.4 Loop Recording

-Speed Unit: Default is MPH. Press OK to select either KM/H or MP/H.

Press the MENU button to exit and complete the setup.

Review and delete images/videos stored in the file folders.

-EVENT: Critical event videos detected by G-Sensor activity or

manually locked by user.

-NORMAL: Standard videos recorded. In Wave Guard Parking

Monitoring, videos are saved in this file folder.

D. FILES

-PHOTO: Standard images.

-All: All the standard videos, critical event videos and standard

imaged recorded.

AB

2018 05

13 25 21

YY / MM / DD

15

to a power source, it will not immediately start on and record.

While recording, the LED indicator will blink and a red dot will flash

on the top left of the screen. You can stop/start the recording at

any time by pressing the OK button.

By default, the Loop Recording Time is 3 minutes. Please go to “RECORD

SETUP”►“Loop Recording” to change it to 1 minute or 5 minutes. When

Loop Recording is turned off, the camera will record video in 25 minute

clips, but will not overwrite old videos when the storage card is full.

The loop recording video file name formats “Year_Date_Time_Serial”.

For example:“2017_0101_060101_001”, . Standard files are stored in the

“Video/Normal” folder. When the Micro SD card is full, the camera will

write over older files.

4.5 Event Recording

- 13 -

Critical event detection is triggered by the G-Sensor (Gravity Sensor)

and will auto-detect vehicle impacts and collisions. This will cause

the camera to protect the current video clip from being overwritten

by locking it and saving the footage in the “Event” folder.

The vehicle driver can also manually lock the current video recording

session by pressing the Emergency Button. A key icon will appear

at the top right of the screen.

The G-Sensor sensitivity is adjustable with 3 settings: Off, Low, Medium

and High– it is set to Medium by default. The G-Sensor can also be

deactivated in “RECORD SETUP”►“G-Sensor ”.

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

Event videos are stored in the “Event” folder, and cannot be

automatically overwritten.

By default, the voice recording is ON. It can be turned OFF using

either of the following methods:

-Go to “RECORD SETUP”►“Audio Recording”, press OK button and

select OFF;

-While recording video, press the Down button to toggle voice

recording OFF/ON.

When the voice recording has been turned OFF, the MIC icon at the

bottom right of the screen will turn white with a red line across it.

4.6 Voice Recording

- 14 -

Note: The camera will auto overwrite old Event videos once

the Event folder has accumulated 30% of the card capacity.

Please regularly transfer important videos to your PC or

another storage location (e.g. external hard drive). To

maintain good read/write performance, the micro SD card

should be formatted every 1-2 two weeks.

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

- 15 -

Parking Mode operates as a sentry function under different situations.

Go to “RECORD SETUP”►“Parking Monitor”, press OK and select the

following distance options: Far, Middle or Near.

To protect your vehicle continuously during parking mode, the

camera will start recording and save to Normal video folder when

it detects moving objects. This is represented by an icon (P) at the

top right side of the screen. When the camera itself feels no vibration

after 5 minutes of recording, the camera automatically to enter the

parking mode.Then the P icon appears on the screen and the screen

goes out. In Parking Mode, once the microwave from the camera

detects movement at the front, it will start auto-recording; it will stop

recording after 10 seconds of inactivity. The P icon appears again

and the screen goes out. In Wave Guard Parking Monitoring, videos

are saved to Normal video folder.

If the camera detects any collisions (detected by G-Sensor) in

parking mode, it will start record and save to Event video folder.

4.7 Wave Guard Parking Monitoring

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

NOTE: If you need to use the Parking Monitor or the 24/7 (All Time)

Protection function, please use the OBD power installation.

- 16 -

If Time Lapse is selected, the camera will take static photos at the set

time interval - either 1, 5 or 10 seconds - to create a video montage.

For example, if you set Time Lapse 1sec, the camera will take one

photo every second, and then stitch the photos together into a 1 fps

video. With a maximum recording frame rate of 30fps, recording

8 hours of video with Time Lapse 1Sec will generate a time lapse

video lasting just 16 minutes (=8 x 60 x 60/30/60). This Eco Mode is

4.8 Time Lapse

recommended for storage cards with smaller capacities.

[Normal Recording Time = Time Lapse Recording Time (Sec) x Recording

Frame Rate FPS x Time Lapse Option]

The camera will auto get out of time lapse recording mode next

time when the camera is turned off. And when the camera is turned

on again, it will record in normal mode.

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

- 17 -

When the camera is recording video, pressing the Emergency/

Camera button will capture a snapshot.

4.9 Taking a Snapshot

An external GPS receiver mount is required to use the camera’s on

board GPS function. This can be purchased from Amazon.

1. Install the External GPS Mount onto the camera instead of the

original mount.

2. Plug the Mini USB Connector into the GPS Mount to power it.

3. Once charged, the camera will power on. Recording will

commence if a Micro SD card has been inserted, just press the

Confirm Button to stop recording.

4. Press the MENU button to enter setup, go to “GPS Setup”►“GPS

Setup” to activate the camera’s GPS function.

5. The GPS receiver will start to search for a GPS signal, this is

represented by a gray GPS icon on the screen. Once the GPS

signal has been received and locked, the icon will turn orange.

4.10 Connecting External GPS Receiver (Optional Accessory)

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

- 18 -

6. You can include GPS tracking and vehicle speed on the video

footage, go to “RECORD SETUP”►“Stamp”►“Speed Stamp” and

to set.

7. You can review recorded video using the VANTRUE® GPS Viewer

(available for download on www.vantrue.net).

Press MENU and go to “FILES”, press OK and UP/DOWN button to

navigate to ►“EVENT” or ►“NORMAL” or ►“PHOTO” or ►“All” file

folders to view and playback videos or photos on the camera display.

Use the UP/DOWN buttons to select the file and press Confirm to

playback/pause. During playback, press UP to rewind, and DOWN

to fast forward.

4.11 Viewing Video/Photos on the Camera

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

0

2018/05/03

00:00:23

05:00:53

1080FHD

3

File View 2018_0101_000652_002

22/47

- 19 -

Press the Emergency/Camera and OK button to delete a single

video/photo or all the files.

1. Connect the camera to your computer using the supplied USB

cable (use the USB port on the camera body, not on the mount).

2. “Mass Storage” will be displayed on the camera screen, starts to

transfer data.

3. Depending on your computer OS, the device will appear either

as a removable drive or a removable volume.

NOTE: When connected to your computer under “Mass Storage”

status, standard camera setup and operations will be disabled.

Viewing files on a computer

The camera has a mini HDMI port for connecting an external display

such as a monitor or TV. Please note that the product doesn’t come

supplied a mini HDMI to HDMI cable.

1. Use a USB charger to charge the camera.

2. Insert the mini HDMI connect or into the camera’s HDMI port.

3. Insert the HDMI connector end into your TV or monitor’s HDMI port.

4. Adjust your display settings to detect the HDMI input source.

5. Once connected to your TV, the camera’s screen will turn black

and be output to your TV screen.

NOTE:

1. To use the HDMI Output Mode, the camera requires a constant

2018_0516_0000209_001

1080FHD

ページを読み込んでいます...

VANTRUE OnDash T2 ユーザーマニュアル

関連論文

その他の書類