Sharp KC-JG20A 取扱説明書

ブランド: Sharp

モデル: KC-JG20A

タイプ: 取扱説明書

ENGLISH

OSAKA, JAPAN

SHARP CORPORATION

Printed in Japan

TINS-A948KKRZ 16KH 1

KC-JG20A

Operation Manual

Free Standing Type

直立型

型號

*本技術標示的數字是將已裝置高濃度PCI離子產生器的加濕型空

氣清新機放置在貼近牆壁的位置，在「中」風速下運行空氣淨化

功能時，在建議面積的房間中央位置附近（距離地面1.2米），

量度出每1立方厘米空氣中所含離子的大約數量。

本產品已裝置了指定容量的離子產生器。

多謝您購買SHARP空氣清新機。

請仔細閱讀本說明書，以便正確地使用本空氣清新機。

使用空氣清新機之前，請務必閱讀「重要安全事項」。

閱讀後請妥善保存本說明書，以便日後翻閱。

AIR PURIFIER

with Humidifying Function

加濕型空氣清新機

使用説明書

*The number attached to this technical mark indicates the

approximate number of ions per cubic centimeter measured at

a point (1.2 m above the floor) near the center of a room of the

Recommended Room Size when an air purifier with the

humidifying function equipped with the high-density

Plasmacluster Ion Generator is running the air purifying

function in the “medium” mode near a wall.

This product is equipped with the generator with the indicated

capacity.

Thank you for purchasing SHARP Air Purifier.

Please read this manual carefully for proper use.

Please be sure to read “SAFETY PRECAUTIONS”

before using the Air Purifier.

After reading, keep the manual in a convenient location

for future reference.

"Plasmacluster" and "Device of a cluster of

grapes" are trademarks of Sharp Corporation.

KC-JG20A(単ページ).indd 1 2016/10/12 10:17:29

ENGLISH

...............................................................................

....................................

..........................................................................

........................................................................

.....................................................................

...........................................................................

...................................................

......................................

....................................................

.............................................................................

.................................................

...................................................

.............................................................................

............

.................................

..................................................

.........................................................

......................................................................

.............................................................

...................................................................

E-2

E-4

E-6

E-8

E-9

E-10

E-11

E-12

E-13

E-14

E-15

E-16

E-18

E-19

E-20

E-22

E-21

E-23

E-24

E-29

Contents

Page

ENGLISH

Preparation

How to use

When needed

Specifications

How to care

FEATURES

IMPORTANT SAFETY INSTRUCTIONS

PARTS NAME

PREPARATION

Filter Installation

Fill the Water Tank

OPERATION

Clean Air & Humidify Mode

Plasmacluster Ion Shower Mode

Clean Air Mode

CONVENIENT FUNCTIONS

Lights Control

Adjustment of Sensor Detection Sensitivity

Auto Restart

Child Lock

Plasmacluster Ion ON/OFF

OFF Timer

Sound Indicator Setting for Water Supply

Frequently Asked Questions

TROUBLESHOOTING

SPECIFICATIONS

CARE AND MAINTENANCE

Main Unit

HEPA Filter /

Active Carbon & Silica Gel Deodorizing Filter

When “Filter Maintenance Indicator Light” turns on

Water Tank / Back Panel / Humidifying Filter / Humidifying Tray

IMPORTANT INFORMATION

Filter Performances

For Effective Use

FILTER REPLACEMENT

HEPA Filter

Active Carbon & Silica Gel Deodorizing Filter

Humidifying Filter

KC-JG20A(単ページ).indd 2 2016/10/12 10:17:30

ENGLISH

...............................................................................

....................................

..........................................................................

........................................................................

.....................................................................

...........................................................................

...................................................

......................................

....................................................

.............................................................................

.................................................

...................................................

.............................................................................

............

.................................

..................................................

.........................................................

......................................................................

.............................................................

...................................................................

E-2

E-4

E-6

E-8

E-9

E-10

E-11

E-12

E-13

E-14

E-15

E-16

E-18

E-19

E-20

E-22

E-21

E-23

E-24

E-29

Contents

Page

ENGLISH

Preparation

How to use

When needed

Specifications

How to care

FEATURES

IMPORTANT SAFETY INSTRUCTIONS

PARTS NAME

PREPARATION

Filter Installation

Fill the Water Tank

OPERATION

Clean Air & Humidify Mode

Plasmacluster Ion Shower Mode

Clean Air Mode

CONVENIENT FUNCTIONS

Lights Control

Adjustment of Sensor Detection Sensitivity

Auto Restart

Child Lock

Plasmacluster Ion ON/OFF

OFF Timer

Sound Indicator Setting for Water Supply

Frequently Asked Questions

TROUBLESHOOTING

SPECIFICATIONS

CARE AND MAINTENANCE

Main Unit

HEPA Filter /

Active Carbon & Silica Gel Deodorizing Filter

When “Filter Maintenance Indicator Light” turns on

Water Tank / Back Panel / Humidifying Filter / Humidifying Tray

IMPORTANT INFORMATION

Filter Performances

For Effective Use

FILTER REPLACEMENT

HEPA Filter

Active Carbon & Silica Gel Deodorizing Filter

Humidifying Filter

KC-JG20A(単ページ).indd 3 2016/10/12 10:17:30

Suppressing the activity of airborne viruses

Viruses suppressing effect of Plasmacluster Air Purifier. This is the effect

in approx. 18 min. (FU-A30) in approx. 25m

sealed test space. (FU-A30)

It is not the effect in actual use space.)

ENGLISH

Auto Mode

E-2

E-3

FEATURES

When the air in the room is polluted suddenly

Encompassing airflow

Active Carbon & Silica Gel Deodorizing Filter

3cm or more

60cm or more

Installation

Install the main unit at the most suitable place.

Do not block air

intake or air outlet by

curtain or furniture.

High-density Plasmacluster

Ions keep your rooms clean

throughout a year

High-density Plasmacluster

Ions keep your rooms clean

throughout a year

・ The same ions as in nature

・ Identified Air Purifying Mechanism

・ Proven Safety of Plasmacluster Ion

Spring

Rainy season

Summer Autumn Winter

Pollen prevention

(Filters effect)

Mold prevention

Suppressing the activity of airborne viruses

Suppressing the activity of airborne allergens of mite droppings and carcasses

Removal of Clinging Odors

Reduction of static electricity

*1 Institut Pasteur in Ho Chi Minh City. The test was conducted in approx. 25m

test

space based on Japan Electrical Manufactures' Association voluntary standard (JEM1467).

In case of FU-A30 (in operation with airflow "MAX"), 99% of allergens can be suppressed in

approx. 18 min.

(The performance of FU-A30 is lower than that of KC-JG20A)

*2 ITEA Corporation. The test was conducted in approx. 25m

test space. In case of FU-F28

(in operation with airflow "MAX"), 99% of allergens can be suppressed in approx. 51 min.

(The performance of FU-F28 is lower than that of KC-JG20A)

*3 In-house investigation. Remove cigarette smoke odor to an unnoticeable level in about 90 minutes.

*4 In-house investigation. Approx. 41m

test space, the initial voltage of 5kV decreased to 0.5kV

after approx. 13 minutes.

*5 LSI Medience Corporation

Clean Ion Shower Mode

Unique airflow quickly collects

dust and odor. To suction air from

all directions at a stretch and

firmly catch dirt with 3 layer filters

Unique airflow quickly collects

dust and odor. To suction air from

all directions at a stretch and

firmly catch dirt with 3 layer filters

Back Panel

(Pre-filter)

HEPA Filter

Large dust

Odor, Formaldehyde

Small dust, virus and allergic substances

Aerodynamic airflow at 20 °

diagonally backward

In case TV or radio broadcast signals

become noisy or an atomic radio watch or

clock does not display the correct time,

move the unit away from the TV, radio or

atomic radio timepieces.

• Use the unit in room temperature between 0 to 35°C

To prevent dew condensation or freezing that leads to

the reduced life or failure of filters.

• Avoid direct sunlight

To prevent deformation, deterioration or discoloration.

• Keep the main unit away from windows or air

blown from air conditioners or heaters

To prevent deformation, deterioration or discoloration

as well as the malfunction of sensors.

• Place the unit on a rigid place

To prevent the floor from being dented or scratched.

• If wall or furniture around the main unit gets dirty,

separate the product from wall sufficiently.

• Be aware of dirt on the floor and surrounding wall

where the unit is used at the same place for a long

period of time

Move the unit and clean the floor and walls

occasionally.

* The dust collecting performance will be the same

even if using the unit 3cm away from the wall,

but place it as far as possible (30cm away

recommended) because it may dirty the wall or

floor around.

The Plasmacluster technology has an effect that

suppresses the activity of airborne viruses and

decomposes and removes allergens such as feces /

carcass of mite. This technology does not create

completely sterile environment or guarantee the

prevention of microbial infection.

The actual number of ions and effect of air purification

vary depending on the environment of the room (such as

the area, shape, whether an air conditioner is used or

ventilation is performed, and where the product is located)

and the usage (such as the blowout direction of ions and

the operation mode).

Sufficient space*

Full-power operation is carried out

by setting the air volume to "MAX" for

60 minutes to purify air rapidly.

Monitors the pollution level, temperature

and humidity of air in a room and

changes the operation automatically.

KC-JG20A(単ページ).indd 4 2016/10/12 10:17:31

Suppressing the activity of airborne viruses

Viruses suppressing effect of Plasmacluster Air Purifier. This is the effect

in approx. 18 min. (FU-A30) in approx. 25m

sealed test space. (FU-A30)

It is not the effect in actual use space.)

ENGLISH

Auto Mode

E-2

E-3

FEATURES

When the air in the room is polluted suddenly

Encompassing airflow

Active Carbon & Silica Gel Deodorizing Filter

3cm or more

60cm or more

Installation

Install the main unit at the most suitable place.

Do not block air

intake or air outlet by

curtain or furniture.

High-density Plasmacluster

Ions keep your rooms clean

throughout a year

High-density Plasmacluster

Ions keep your rooms clean

throughout a year

・ The same ions as in nature

・ Identified Air Purifying Mechanism

・ Proven Safety of Plasmacluster Ion

Spring

Rainy season

Summer Autumn Winter

Pollen prevention

(Filters effect)

Mold prevention

Suppressing the activity of airborne viruses

Suppressing the activity of airborne allergens of mite droppings and carcasses

Removal of Clinging Odors

Reduction of static electricity

*1 Institut Pasteur in Ho Chi Minh City. The test was conducted in approx. 25m

test

space based on Japan Electrical Manufactures' Association voluntary standard (JEM1467).

In case of FU-A30 (in operation with airflow "MAX"), 99% of allergens can be suppressed in

approx. 18 min.

(The performance of FU-A30 is lower than that of KC-JG20A)

*2 ITEA Corporation. The test was conducted in approx. 25m

test space. In case of FU-F28

(in operation with airflow "MAX"), 99% of allergens can be suppressed in approx. 51 min.

(The performance of FU-F28 is lower than that of KC-JG20A)

*3 In-house investigation. Remove cigarette smoke odor to an unnoticeable level in about 90 minutes.

*4 In-house investigation. Approx. 41m

test space, the initial voltage of 5kV decreased to 0.5kV

after approx. 13 minutes.

*5 LSI Medience Corporation

Clean Ion Shower Mode

Unique airflow quickly collects

dust and odor. To suction air from

all directions at a stretch and

firmly catch dirt with 3 layer filters

Unique airflow quickly collects

dust and odor. To suction air from

all directions at a stretch and

firmly catch dirt with 3 layer filters

Back Panel

(Pre-filter)

HEPA Filter

Large dust

Odor, Formaldehyde

Small dust, virus and allergic substances

Aerodynamic airflow at 20 °

diagonally backward

In case TV or radio broadcast signals

become noisy or an atomic radio watch or

clock does not display the correct time,

move the unit away from the TV, radio or

atomic radio timepieces.

• Use the unit in room temperature between 0 to 35°C

To prevent dew condensation or freezing that leads to

the reduced life or failure of filters.

• Avoid direct sunlight

To prevent deformation, deterioration or discoloration.

• Keep the main unit away from windows or air

blown from air conditioners or heaters

To prevent deformation, deterioration or discoloration

as well as the malfunction of sensors.

• Place the unit on a rigid place

To prevent the floor from being dented or scratched.

• If wall or furniture around the main unit gets dirty,

separate the product from wall sufficiently.

• Be aware of dirt on the floor and surrounding wall

where the unit is used at the same place for a long

period of time

Move the unit and clean the floor and walls

occasionally.

* The dust collecting performance will be the same

even if using the unit 3cm away from the wall,

but place it as far as possible (30cm away

recommended) because it may dirty the wall or

floor around.

The Plasmacluster technology has an effect that

suppresses the activity of airborne viruses and

decomposes and removes allergens such as feces /

carcass of mite. This technology does not create

completely sterile environment or guarantee the

prevention of microbial infection.

The actual number of ions and effect of air purification

vary depending on the environment of the room (such as

the area, shape, whether an air conditioner is used or

ventilation is performed, and where the product is located)

and the usage (such as the blowout direction of ions and

the operation mode).

Sufficient space*

Full-power operation is carried out

by setting the air volume to "MAX" for

60 minutes to purify air rapidly.

Monitors the pollution level, temperature

and humidity of air in a room and

changes the operation automatically.

KC-JG20A(単ページ).indd 5 2016/10/12 10:17:32

ENGLISH

E-4

E-5

IMPORTANT SAFETY INSTRUCTIONS

WARNING

– Always follow below instructions to reduce the risk of electric shock, fire, or injury:

NOTE

– Instructions when the unit interferes with radio or TV reception

If the air purifier interferes with radio or television reception, try one or more of the following measures:

• Follow the instructions in this manual for proper filter care and maintenance.

• Read all instructions before using the unit.

• Use only a 220 volt outlet.

• Do not use the unit if the power cord or plug is damaged or if the connection to the wall outlet is loose.

• Periodically remove dust from the plug.

• Do not insert fingers or foreign objects into the air intake or air outlet.

• When removing the power plug, always hold the plug and never pull on the cord.

Failure to do so can cause a short circuit resulting in electric shock or fire.

• When moving the unit, do not damage the power cord with the casters.

Failure to do so can cause electric shock, heat generation, or fire.

• Do not remove the plug when your hands are wet.

• Do not place the unit near gas appliances or fireplaces.

• Always unplug the unit when refilling the water tank, cleaning the unit, or when the unit is not in use. Failure to

do so can cause a short circuit resulting in electric shock or fire.

•

In order to avoid safety hazards, if the power cord is damaged, it must be replaced by either the

manufacturer, a service agent, a Sharp Authorized Service Center or a similarly qualified service provider.

• Only a Sharp Authorized Service Centre should service this air purifier. Contact the nearest Service Centre for

any problems, adjustments, or repairs.

• Do not operate the unit in rooms where aerosol insecticides are present. Do not operate the unit in rooms

where there is oily residue, incense, sparks from lit cigarettes, or chemical fumes in the air. Do not operate the

unit in places where it may get wet, such as a bathroom.

• Be cautious when cleaning the unit. Strong corrosive cleansers can damage the exterior.

• When carrying the unit, first remove the Water Tank and Humidifying Tray, and then hold the unit by the

handles on both sides.

• Do not drink the water in the Humidifying Tray or Water Tank.

• Replace the water in the Water Tank daily with fresh tap water, and regularly clean the Water Tank and

Humidifying Tray (Ref. E-10, 16, 17 and 20). When the unit is not in use, remove water from the Water Tank

and Humidifying Tray. Leaving water in the Water Tank or Humidifying Tray can cause mold, bacteria, and bad

odors.

• This applian

ce is not intended for use by persons (including children) with reduced physical, sensory, or mental

capabilities, nor by persons with insufficient experience and knowledge of how to operate the unit, unless they

are given proper supervision and instruction on how to use the unit by a person responsible for their safety.

Do not allow children to play with the unit.

• Adjust or relocate the receiving antenna.

• Increase the distance between the unit and the radio or TV.

• Connect the equipment into an outlet on a circuit different from that of the radio or TV receiver.

• Consult the dealer or a qualified radio or TV technician.

CAUTIONS CONCERNING OPERATION

INSTALLATION GUIDELINES

FILTER GUIDELINES

• Do not block the air intake or air outlet.

• Do not place the unit near or on hot objects, such as stoves or heaters, or where it may come into contact with

steam.

• Always operate the unit in an upright position.

• When moving the unit, use the handles on both sides.

Do not move the unit when it is in operation.

• If the unit is on tatami mat, easily damaged floor, an uneven surface, or thick-piled carpet, lift it up when

moving.

• When moving the unit by its casters, move it slowly and in a horizontal direction.

• Before moving the unit, make sure it is not operating, and remove the Water Tank and Humidifying Tray while

holding the handles of the unit.

• When removing the Water Tank, be careful not to get your fingers caught inside the unit.

• Do not operate the unit without the filters, the Water Tank, and the Humidifying Tray properly installed.

• Do not wash and reuse the HEPA filter and the Active Carbon Deodorizing Filter.

It will not improve filter performance and may cause electric shock or malfunction.

• Clean the exterior with a soft cloth only.

Do not use volatile fluids or detergents.

Doing so may damage or crack the exterior of the unit and cause sensor malfunctions.

• The frequency of descaling maintenance will depend on the hardness of and the impurities in the

water used; the harder the water the more often descaling will be necessary.

• Keep the unit away from water.

• When using the unit, place it at least 2-meters away from equipment that emits electric waves, such as

televisions or radios, to avoid electrical interference.

• Avoid locations where the sensors are exposed to direct wind.

Doing so may cause malfunctions.

• Avoid locations where furniture, fabrics, or other objects can come in contact with the unit and

interfere with the intake and air outlet.

• Avoid locations where the unit is exposed to condensation or drastic changes in temperature.

Appropriate room temperature is between 0 – 35 ºC.

• Place the unit on a level and stable surface with sufficient air circulation.

When placed on heavy carpet, the unit may vibrate slightly.

Place the unit on a level surface to avoid water leakage from the Water Tank and Humidifying Tray.

• Avoid locations that generate grease or oily smoke.

Doing so may cause the unit exterior to crack and the sensors to malfunction.

• To ensure proper airflow, place the unit about 30 cm (1 ft) away from the wall.

The wall directly behind the air outlet may become dirty over time. When using the unit for an extended period

of time at the same location, periodically clean the walls adjacent to it. You can also prevent walls from

becoming dirty by covering them with a vinyl sheet or other protective covering.

• To move the unit with casters, check that the casters (on right and left sides) are unlocked and move it

slowly in the lateral direction only.

Always follow basic safety precautions when using electrical appliances, including the following:

KC-JG20A(単ページ).indd 6 2016/10/12 10:17:33

ENGLISH

E-4

E-5

IMPORTANT SAFETY INSTRUCTIONS

WARNING

– Always follow below instructions to reduce the risk of electric shock, fire, or injury:

NOTE

– Instructions when the unit interferes with radio or TV reception

If the air purifier interferes with radio or television reception, try one or more of the following measures:

• Follow the instructions in this manual for proper filter care and maintenance.

• Read all instructions before using the unit.

• Use only a 220 volt outlet.

• Do not use the unit if the power cord or plug is damaged or if the connection to the wall outlet is loose.

• Periodically remove dust from the plug.

• Do not insert fingers or foreign objects into the air intake or air outlet.

• When removing the power plug, always hold the plug and never pull on the cord.

Failure to do so can cause a short circuit resulting in electric shock or fire.

• When moving the unit, do not damage the power cord with the casters.

Failure to do so can cause electric shock, heat generation, or fire.

• Do not remove the plug when your hands are wet.

• Do not place the unit near gas appliances or fireplaces.

• Always unplug the unit when refilling the water tank, cleaning the unit, or when the unit is not in use. Failure to

do so can cause a short circuit resulting in electric shock or fire.

•

In order to avoid safety hazards, if the power cord is damaged, it must be replaced by either the

manufacturer, a service agent, a Sharp Authorized Service Center or a similarly qualified service provider.

• Only a Sharp Authorized Service Centre should service this air purifier. Contact the nearest Service Centre for

any problems, adjustments, or repairs.

• Do not operate the unit in rooms where aerosol insecticides are present. Do not operate the unit in rooms

where there is oily residue, incense, sparks from lit cigarettes, or chemical fumes in the air. Do not operate the

unit in places where it may get wet, such as a bathroom.

• Be cautious when cleaning the unit. Strong corrosive cleansers can damage the exterior.

• When carrying the unit, first remove the Water Tank and Humidifying Tray, and then hold the unit by the

handles on both sides.

• Do not drink the water in the Humidifying Tray or Water Tank.

• Replace the water in the Water Tank daily with fresh tap water, and regularly clean the Water Tank and

Humidifying Tray (Ref. E-10, 16, 17 and 20). When the unit is not in use, remove water from the Water Tank

and Humidifying Tray. Leaving water in the Water Tank or Humidifying Tray can cause mold, bacteria, and bad

odors.

• This applian

ce is not intended for use by persons (including children) with reduced physical, sensory, or mental

capabilities, nor by persons with insufficient experience and knowledge of how to operate the unit, unless they

are given proper supervision and instruction on how to use the unit by a person responsible for their safety.

Do not allow children to play with the unit.

• Adjust or relocate the receiving antenna.

• Increase the distance between the unit and the radio or TV.

• Connect the equipment into an outlet on a circuit different from that of the radio or TV receiver.

• Consult the dealer or a qualified radio or TV technician.

CAUTIONS CONCERNING OPERATION

INSTALLATION GUIDELINES

FILTER GUIDELINES

• Do not block the air intake or air outlet.

• Do not place the unit near or on hot objects, such as stoves or heaters, or where it may come into contact with

steam.

• Always operate the unit in an upright position.

• When moving the unit, use the handles on both sides.

Do not move the unit when it is in operation.

• If the unit is on tatami mat, easily damaged floor, an uneven surface, or thick-piled carpet, lift it up when

moving.

• When moving the unit by its casters, move it slowly and in a horizontal direction.

• Before moving the unit, make sure it is not operating, and remove the Water Tank and Humidifying Tray while

holding the handles of the unit.

• When removing the Water Tank, be careful not to get your fingers caught inside the unit.

• Do not operate the unit without the filters, the Water Tank, and the Humidifying Tray properly installed.

• Do not wash and reuse the HEPA filter and the Active Carbon Deodorizing Filter.

It will not improve filter performance and may cause electric shock or malfunction.

• Clean the exterior with a soft cloth only.

Do not use volatile fluids or detergents.

Doing so may damage or crack the exterior of the unit and cause sensor malfunctions.

• The frequency of descaling maintenance will depend on the hardness of and the impurities in the

water used; the harder the water the more often descaling will be necessary.

• Keep the unit away from water.

• When using the unit, place it at least 2-meters away from equipment that emits electric waves, such as

televisions or radios, to avoid electrical interference.

• Avoid locations where the sensors are exposed to direct wind.

Doing so may cause malfunctions.

• Avoid locations where furniture, fabrics, or other objects can come in contact with the unit and

interfere with the intake and air outlet.

• Avoid locations where the unit is exposed to condensation or drastic changes in temperature.

Appropriate room temperature is between 0 – 35 ºC.

• Place the unit on a level and stable surface with sufficient air circulation.

When placed on heavy carpet, the unit may vibrate slightly.

Place the unit on a level surface to avoid water leakage from the Water Tank and Humidifying Tray.

• Avoid locations that generate grease or oily smoke.

Doing so may cause the unit exterior to crack and the sensors to malfunction.

• To ensure proper airflow, place the unit about 30 cm (1 ft) away from the wall.

The wall directly behind the air outlet may become dirty over time. When using the unit for an extended period

of time at the same location, periodically clean the walls adjacent to it. You can also prevent walls from

becoming dirty by covering them with a vinyl sheet or other protective covering.

• To move the unit with casters, check that the casters (on right and left sides) are unlocked and move it

slowly in the lateral direction only.

Always follow basic safety precautions when using electrical appliances, including the following:

KC-JG20A(単ページ).indd 7 2016/10/12 10:17:33

ENGLISH

Fan Speed Button /

Indicator Light (light green)

Filter Reset Button/

Indicator Light (light green)

OFF Timer Button/

Dust Monitor

(Temperature and humidity sensor /

dust sensor)

Child Lock Button/

Indicator Light

(light green)

Power Off Button

Plasmacluster Ion Indicator Light (blue)

Lighting: “ON”, Not lighting: “OFF”

Lights Control Button

Clean Air & Humidify Mode Button / Indicator Light (light green)

Plasmacluster Ion Shower Mode Button / Indicator Light (light green)

Clean Air Mode Button / Indicator Light (light green)

Sensor Unit

(internal)

Handle

(left and right)

Handle of Water Tank

Back

Humidifying Filter

Water Tank

Do Not Remove!

Humidifying Tray

Float

Tray Partition

Roller

Back Panel

(Pre-filter)

Air Intake

HEPA Filter

Active Carbon & Silica

Gel Deodorizing Filter

Air Outlet (back)

Louver (automatic)

Caster

(4 locations)

Power cord

(plug shape varies by country)

Plug

Do not block the

air outlet or air intake.

Tank Cap

Main

Unit

Front

Air Outlet (front)

Caster

Lock

Main Unit, Control Panel and Front Monitor

Filter Maintenance Indicator

Light (orange)

Plasmacluster Ion

ON/OFF Button

Front Monitor

Indicates the air conditions and approximate humidity in a room.

Humidifying Indicator Light

Red

(Flashing)

Fill water　　

Off

Not humidifying

Green

Humidifying

Humidity level cannot be set.

Current Humidity Indicator (green)

Green

Red

Room air

Clean

Dirty

Control Panel

E-11

page

E-16

page

E-12

page

E-14

page

E-12

page

E-12

page

E-11

page

E-10

page

E-10

page

E-10～11

page

E-10～11

page

Indicates the pollution level of

room air with 5 levels *.

This styrene foam

is not a packing

material.

Be sure to attach it

during operation even if

humidification operation

is not carried out.

PARTS NAME

E-6

E-7

Press any button

indicated with to

start operation.

Indicates the present humidity (estimated).

(Display ranges from 6% to 99% by percent)

Casters can be moved

only in the lateral direction.

KC-JG20A(単ページ).indd 8 2016/10/12 10:17:34

ENGLISH

Fan Speed Button /

Indicator Light (light green)

Filter Reset Button/

Indicator Light (light green)

OFF Timer Button/

Dust Monitor

(Temperature and humidity sensor /

dust sensor)

Child Lock Button/

Indicator Light

(light green)

Power Off Button

Plasmacluster Ion Indicator Light (blue)

Lighting: “ON”, Not lighting: “OFF”

Lights Control Button

Clean Air & Humidify Mode Button / Indicator Light (light green)

Plasmacluster Ion Shower Mode Button / Indicator Light (light green)

Clean Air Mode Button / Indicator Light (light green)

Sensor Unit

(internal)

Handle

(left and right)

Handle of Water Tank

Back

Humidifying Filter

Water Tank

Do Not Remove!

Humidifying Tray

Float

Tray Partition

Roller

Back Panel

(Pre-filter)

Air Intake

HEPA Filter

Active Carbon & Silica

Gel Deodorizing Filter

Air Outlet (back)

Louver (automatic)

Caster

(4 locations)

Power cord

(plug shape varies by country)

Plug

Do not block the

air outlet or air intake.

Tank Cap

Main

Unit

Front

Air Outlet (front)

Caster

Lock

Main Unit, Control Panel and Front Monitor

Filter Maintenance Indicator

Light (orange)

Plasmacluster Ion

ON/OFF Button

Front Monitor

Indicates the air conditions and approximate humidity in a room.

Humidifying Indicator Light

Red

(Flashing)

Fill water　　

Off

Not humidifying

Green

Humidifying

Humidity level cannot be set.

Current Humidity Indicator (green)

Green

Red

Room air

Clean

Dirty

Control Panel

E-11

page

E-16

page

E-12

page

E-14

page

E-12

page

E-12

page

E-11

page

E-10

page

E-10

page

E-10～11

page

E-10～11

page

Indicates the pollution level of

room air with 5 levels *.

This styrene foam

is not a packing

material.

Be sure to attach it

during operation even if

humidification operation

is not carried out.

PARTS NAME

E-6

E-7

Press any button

indicated with to

start operation.

Indicates the present humidity (estimated).

(Display ranges from 6% to 99% by percent)

Casters can be moved

only in the lateral direction.

KC-JG20A(単ページ).indd 9 2016/10/12 10:17:35

ENGLISH

E-8

E-9

PREPARATION

Be sure to install filters before plugging the unit.

Filter Installation

Back Panel

Upper tabs (one each

at right and left)

Active Carbon & Silica Gel Deodorizing Filter

Active Carbon &

Silica Gel

Deodorizing Filter

Active Carbon & Silica Gel

Deodorizing Filter

HEPA Filter

Tag

No difference on both sides

Click

Fill the Water Tank

Fill tap water in the Water Tank to operate the unit in the Clean Air & Humidify mode.

Remove the

back panel

to take the

filters out.

• The filters (2 types) are

found in the main unit.

Take filters (2 types)

out of plastic bags

Tag surface should be

attached to the front side

Mount the

back panel

Lower tabs (one each at

right and left)

Handle of

water tank

Water tank

Press down the

Handle of Water Tank,

and then pull the

Water Tank out

• Be careful, do not let water spill over.

Tank cap

Water tank

Fill water

Unscrew the

Water Tank Cap

and fill tap water

in the Water Tank

•

Before filling water, drain the remaining

water in the Water Tank and then rinse

it by shaking with a small amount of

fresh tap water.

The Water

Tank is

self-standing.

Click

Tighten the

Water Tank Cap

Install the Water

Tank

• Tighten the Cap firmly to make

sure no water leaks out.

• Be sure to wipe off water droplet

on the Water Tank.

• Take care not to get fingers caught

between the main unit and Water

Tank.

• Firmly hold the main unit for

mounting the Water Tank.

• Use tap water only. (Otherwise, breed of bacteria may occur)

• Do not fill hot water (≥ 40°C), aroma oil, chemicals, dirty water, detergent or aromatic

substances into the Water Tank. (Otherwise, cracks and/or water leakage could result)

Caution

• Pull the tag of the HEPA

filter out to the Active

Carbon & Silica Gel

Deodorizing Filter to

make it easy to remove it.

Install the filters

in order from the

HEPA Filter to the

Active Carbon &

Silica Gel

Deodorizing

Filter.

KC-JG20A(単ページ).indd 10 2016/10/12 10:17:36

ENGLISH

E-8

E-9

PREPARATION

Be sure to install filters before plugging the unit.

Filter Installation

Back Panel

Upper tabs (one each

at right and left)

Active Carbon & Silica Gel Deodorizing Filter

Active Carbon &

Silica Gel

Deodorizing Filter

Active Carbon & Silica Gel

Deodorizing Filter

HEPA Filter

Tag

No difference on both sides

Click

Fill the Water Tank

Fill tap water in the Water Tank to operate the unit in the Clean Air & Humidify mode.

Remove the

back panel

to take the

filters out.

• The filters (2 types) are

found in the main unit.

Take filters (2 types)

out of plastic bags

Tag surface should be

attached to the front side

Mount the

back panel

Lower tabs (one each at

right and left)

Handle of

water tank

Water tank

Press down the

Handle of Water Tank,

and then pull the

Water Tank out

• Be careful, do not let water spill over.

Tank cap

Water tank

Fill water

Unscrew the

Water Tank Cap

and fill tap water

in the Water Tank

•

Before filling water, drain the remaining

water in the Water Tank and then rinse

it by shaking with a small amount of

fresh tap water.

The Water

Tank is

self-standing.

Click

Tighten the

Water Tank Cap

Install the Water

Tank

• Tighten the Cap firmly to make

sure no water leaks out.

• Be sure to wipe off water droplet

on the Water Tank.

• Take care not to get fingers caught

between the main unit and Water

Tank.

• Firmly hold the main unit for

mounting the Water Tank.

• Use tap water only. (Otherwise, breed of bacteria may occur)

• Do not fill hot water (≥ 40°C), aroma oil, chemicals, dirty water, detergent or aromatic

substances into the Water Tank. (Otherwise, cracks and/or water leakage could result)

Caution

• Pull the tag of the HEPA

filter out to the Active

Carbon & Silica Gel

Deodorizing Filter to

make it easy to remove it.

Install the filters

in order from the

HEPA Filter to the

Active Carbon &

Silica Gel

Deodorizing

Filter.

KC-JG20A(単ページ).indd 11 2016/10/12 10:17:37

ENGLISH

Humidifying Indicator Light

E-10

E-11

The operation in this mode is generally recommended. (Humidity level cannot be set.)

OPERATION

Clean Air & Humidify Mode

Beep

Beepー

Red

(Flashing)

Off

Green

Humidifying

Not humidifying

Fill water　　

Off

Not humidifying

When the air in a room suddenly becomes polluted

Plasmacluster Ion Shower Mode

Beep

Beepー

Red

(Flashing)

Off

Green

Humidifying

Not humidifying

Fill water　　

Insert the plug into

the socket.

Fill water Operate Stop

Stop

Water tank

E-9

page

Fill up the Water

Tank with tap

water

E-11

page

Select a preferred

fan speed

• When operating the unit for the first time

after the plug is inserted into the socket,

default operation sets the fan speed at

“AUTO” and Plasmacluster Ion “ON”.

• From the second time onwards, the unit

operates with the same setting as the

previous one.

* When the fan speed is set at “AUTO” or

“POLLEN”, the unit stops humidifying when

it reaches the optimal humidity level and the

Humidifying Indicator Light turns OFF.

Caution

• When water in the Water Tank runs out, the Humidifying Indicator Light blinks in red and starts

operation without humidifying function.

• When the fan speed is set to “AUTO” or "POLLEN", the unit controls

the humidifying level for the optimized humidity. However, the humidity

could be too high or too low depending on the size or condition of the

room in which the unit is installed.

• If humidity is too low: Set the fan speed to “MAX” or “MED” for operation.

• If humidity is too high: Operate the unit in the clean air mode.

Room temperature Optimal humidity

Clean Air Mode

Suitable for rainy seasons or when the humidity is high. (operable without filling the Water Tank)

Beep

Beepー

E-11

page

Operate Stop

Select a preferred

fan speed

• When operating the unit for the first time

after the plug is inserted into the socket,

default operation sets the fan speed at

“AUTO” and Plasmacluster Ion “ON”.

• From the second time onwards, the unit

operates with the same setting as the

previous one.

• When eliminating pollens brought home

• During or after vacuum-cleaning

• When taking in the laundry hung outdoors

• When quickly deodorizing household odors

• When deodorizing cooking smell or odors

from the laundry dried indoors

* When humidity reaches the optimal level,

the unit stops humidifying and the

Humidifying Indicator Light turns OFF.

* When the unit starts operation in the

Plasmacluster Ion Shower mode while the

Water Tank is empty, the Humidifying

Indicator Light will not turn ON.

Fan Speed

Press the Fan Speed Button to change settings as

follows:

Select a preferred

fan speed

Select the preferred fan setting in the Clean Air & Humidify mode or

Clean Air mode.

This setting is not available during operation in the Plasmacluster Ion Shower mode.

Beep,

Beep

Beep Beep

Monitors the room condition with the “Dust, Temperature and Humidity Sensor” and

automatically switch the fan speed.

Keeps operating at the “LOW” speed quietly.

Keeps operating at the “MED” fan speed.

Keeps operating at the “MAX” fan speed. (The noise level will be louder)

Operates the unit at MAX fan speed for the first 10 minutes, and then at LOW and

MAX fan speed at 20-minute intervals alternately to effectively eliminate pollens.

Operate

Operation with MAX airflow for 60 minutes to purify

air rapidly.

The operation mode automatically returns to the

previous setting after 60 minutes.

AUTO

POLLEN

MAX

MED

LOW

• When water in the Water Tank runs out, the Humidifying Indicator Light blinks in red and starts

operation without humidifying function.

• When the Plasmacluster Ion ( 　 ) is “OFF”, the unit will not discharge Plasmacluster Ion but still

remove dust and odors by filters.

Caution

KC-JG20A(単ページ).indd 12 2016/10/12 10:17:38

ENGLISH

Humidifying Indicator Light

E-10

E-11

The operation in this mode is generally recommended. (Humidity level cannot be set.)

OPERATION

Clean Air & Humidify Mode

Beep

Beepー

Red

(Flashing)

Off

Green

Humidifying

Not humidifying

Fill water　　

Off

Not humidifying

When the air in a room suddenly becomes polluted

Plasmacluster Ion Shower Mode

Beep

Beepー

Red

(Flashing)

Off

Green

Humidifying

Not humidifying

Fill water　　

Insert the plug into

the socket.

Fill water Operate Stop

Stop

Water tank

E-9

page

Fill up the Water

Tank with tap

water

E-11

page

Select a preferred

fan speed

• When operating the unit for the first time

after the plug is inserted into the socket,

default operation sets the fan speed at

“AUTO” and Plasmacluster Ion “ON”.

• From the second time onwards, the unit

operates with the same setting as the

previous one.

* When the fan speed is set at “AUTO” or

“POLLEN”, the unit stops humidifying when

it reaches the optimal humidity level and the

Humidifying Indicator Light turns OFF.

Caution

• When water in the Water Tank runs out, the Humidifying Indicator Light blinks in red and starts

operation without humidifying function.

• When the fan speed is set to “AUTO” or "POLLEN", the unit controls

the humidifying level for the optimized humidity. However, the humidity

could be too high or too low depending on the size or condition of the

room in which the unit is installed.

• If humidity is too low: Set the fan speed to “MAX” or “MED” for operation.

• If humidity is too high: Operate the unit in the clean air mode.

Room temperature Optimal humidity

Clean Air Mode

Suitable for rainy seasons or when the humidity is high. (operable without filling the Water Tank)

Beep

Beepー

E-11

page

Operate Stop

Select a preferred

fan speed

• When operating the unit for the first time

after the plug is inserted into the socket,

default operation sets the fan speed at

“AUTO” and Plasmacluster Ion “ON”.

• From the second time onwards, the unit

operates with the same setting as the

previous one.

• When eliminating pollens brought home

• During or after vacuum-cleaning

• When taking in the laundry hung outdoors

• When quickly deodorizing household odors

• When deodorizing cooking smell or odors

from the laundry dried indoors

* When humidity reaches the optimal level,

the unit stops humidifying and the

Humidifying Indicator Light turns OFF.

* When the unit starts operation in the

Plasmacluster Ion Shower mode while the

Water Tank is empty, the Humidifying

Indicator Light will not turn ON.

Fan Speed

Press the Fan Speed Button to change settings as

follows:

Select a preferred

fan speed

Select the preferred fan setting in the Clean Air & Humidify mode or

Clean Air mode.

This setting is not available during operation in the Plasmacluster Ion Shower mode.

Beep,

Beep

Beep Beep

Monitors the room condition with the “Dust, Temperature and Humidity Sensor” and

automatically switch the fan speed.

Keeps operating at the “LOW” speed quietly.

Keeps operating at the “MED” fan speed.

Keeps operating at the “MAX” fan speed. (The noise level will be louder)

Operates the unit at MAX fan speed for the first 10 minutes, and then at LOW and

MAX fan speed at 20-minute intervals alternately to effectively eliminate pollens.

Operate

Operation with MAX airflow for 60 minutes to purify

air rapidly.

The operation mode automatically returns to the

previous setting after 60 minutes.

AUTO

POLLEN

MAX

MED

LOW

• When water in the Water Tank runs out, the Humidifying Indicator Light blinks in red and starts

operation without humidifying function.

• When the Plasmacluster Ion ( 　 ) is “OFF”, the unit will not discharge Plasmacluster Ion but still

remove dust and odors by filters.

Caution

KC-JG20A(単ページ).indd 13 2016/10/12 10:17:39

ENGLISH

E-12

E-13

CONVENIENT FUNCTIONS

Lights Control

Press the Button when the monitor or Plasmacluster Ion Indicator Light is too bright

Beep

(In operation) (In operation)

Off

Adjustment of Sensor Detection Sensitivity

(When the unit is OFF)

Dust Monitor

does not change from "Red"

(frequently becomes "Red")

(frequently becomes "Green")

does not change from "Green"

…… adjust it to "Low"

…… adjust it to "High"

Auto Restart

If you want to restart the operation automatically when the power is recovered from electric power failure

• When it is "OFF":

The Plasmacluster

Indicator Light (blue)

goes out.

Child Lock

When you want to prevent mishandling by children.

Setting/Canceling

Press for at least

3 seconds

Press for at least

3 seconds

“Set”

“Cancel”

• If you set the child lock, the operation other

than cancellation of child lock is disabled.

If the main unit is unplugged, the setting is

released.

(While auto restart is set, the child lock is

not cancelled even if the main unit is

unplugged.)

E-13

page

Press for at least

3 seconds

Press for at least

3 seconds

Press for at least

3 seconds

Beep

Beep,

Beep

"LOW", "MED", and "MAX" Lights

are lighting for 10 seconds

• Even if the main unit unplugged or the

breaker cuts off during operation, the

operation is restarted with previous

operation mode and setting after power

recovery.

Setting

(In operation)

Plasmacluster Ion

Indicator Light

Front Monitor

• Press the Button to change settings as follows:

Bright

Dim

Off

Caution

• When the light is set to “OFF”, the Humidifying Indicator Light starts blinking once water needs

to be filled.

• When the light is set to “OFF”, it operates in "Dim" mode if the unit is restarted.

Plasmacluster Ion ( ) ON/OFF

Press the Button to turn ON or OFF the Plasmacluster Ion function

ON/OFF

“ON” “OFF”

Beep,

Beep

Beep,

Beep

(In 8 seconds)

select the

preferred sensor

detection

sensitivity

Beep

Beepー

Completed

Setting Canceling

• Fan Speed Indicator Light indicates the

current sensor detection sensitivity.

(“Standard” by default)

• Press the Button to change settings as

follows:

• Adjustment automatically finishes if the

Power OFF button is pressed in 8 seconds.

• The sensor detection sensitivity setting

will be saved even if the unit is

unplugged.

・Household dust (dust, dust mite feces and dead mites, mold spores, pollens), cigarette smoke etc.

Sensors detect:

“LOW”

“Standard”

“HIGH”

Beep

Beep,

Beep

KC-JG20A(単ページ).indd 14 2016/10/12 10:17:39

ENGLISH

E-12

E-13

CONVENIENT FUNCTIONS

Lights Control

Press the Button when the monitor or Plasmacluster Ion Indicator Light is too bright

Beep

(In operation) (In operation)

Off

Adjustment of Sensor Detection Sensitivity

(When the unit is OFF)

Dust Monitor

does not change from "Red"

(frequently becomes "Red")

(frequently becomes "Green")

does not change from "Green"

…… adjust it to "Low"

…… adjust it to "High"

Auto Restart

If you want to restart the operation automatically when the power is recovered from electric power failure

• When it is "OFF":

The Plasmacluster

Indicator Light (blue)

goes out.

Child Lock

When you want to prevent mishandling by children.

Setting/Canceling

Press for at least

3 seconds

Press for at least

3 seconds

“Set”

“Cancel”

• If you set the child lock, the operation other

than cancellation of child lock is disabled.

If the main unit is unplugged, the setting is

released.

(While auto restart is set, the child lock is

not cancelled even if the main unit is

unplugged.)

E-13

page

Press for at least

3 seconds

Press for at least

3 seconds

Press for at least

3 seconds

Beep

Beep,

Beep

"LOW", "MED", and "MAX" Lights

are lighting for 10 seconds

• Even if the main unit unplugged or the

breaker cuts off during operation, the

operation is restarted with previous

operation mode and setting after power

recovery.

Setting

(In operation)

Plasmacluster Ion

Indicator Light

Front Monitor

• Press the Button to change settings as follows:

Bright

Dim

Off

Caution

• When the light is set to “OFF”, the Humidifying Indicator Light starts blinking once water needs

to be filled.

• When the light is set to “OFF”, it operates in "Dim" mode if the unit is restarted.

Plasmacluster Ion ( ) ON/OFF

Press the Button to turn ON or OFF the Plasmacluster Ion function

ON/OFF

“ON” “OFF”

Beep,

Beep

Beep,

Beep

(In 8 seconds)

select the

preferred sensor

detection

sensitivity

Beep

Beepー

Completed

Setting Canceling

• Fan Speed Indicator Light indicates the

current sensor detection sensitivity.

(“Standard” by default)

• Press the Button to change settings as

follows:

• Adjustment automatically finishes if the

Power OFF button is pressed in 8 seconds.

• The sensor detection sensitivity setting

will be saved even if the unit is

unplugged.

・Household dust (dust, dust mite feces and dead mites, mold spores, pollens), cigarette smoke etc.

Sensors detect:

“LOW”

“Standard”

“HIGH”

Beep

Beep,

Beep

KC-JG20A(単ページ).indd 15 2016/10/12 10:17:40

ENGLISH

E-14

E-15

The operation will be automatically stopped as scheduled.

1 Hour 2 Hours 4 Hours 8 Hours OFF

Frequently Asked Questions

CONVENIENT FUNCTIONS

(Continued)

Check

(Within 3

seconds)

Select the

preferred time

Press for at least

3 seconds

Press for at least

3 seconds

Setting/Canceling Setting/Canceling

(In operation)

(While the timer is in operation)

OFF Timer

Beep

Beep Beep Beep Beep

Beep,

Beep

• The setting is automatically completed when no

operation is performed for 3 seconds.

(The OFF Timer Indicator Light will turn on)

• To turn off, change the setting to display “ (OFF)”.

(The OFF Timer Indicator Light will turn off.)

• It returns to the previous display in 3 seconds after the

setting is changed.

• The remaining time is displayed when pressing the

button once. (The time is rounded up to the nearest hour)

• If you press the OFF timer button while the remaining

time is displayed, you can change the setting time or turn

off the OFF timer.

(Example)

Remaining time: Over 3 hours and less than 4 hours

Sound Indicator Setting for Water Supply

(When the unit is OFF) (When the unit is OFF)

“Set” “Cancel”

Beep,

Beep

• When this setting is “ON”, the unit

generates an audible beep sound (for

about 10 seconds) while the Humidifying

Indicator Light is blinking.

• When the setting is “OFF”, the unit

generates no beep sound while the

Humidifying Indicator Light is blinking.

• If the unit is unplugged, this setting will be

cancelled and no beep sound will be

generated.

When the Humidifying Filter is moisturized, humid air will be discharged from air

outlet. Humidification is achieved without water-boiling, so steam or vapour cannot

be seen. It will not humidify the room excessively.

I do not see steam. Is it really humidifying? Doesn't

the product humidify the room too much?

Humidity may not rise to the optimal level when there is no water in the tank or the

humidifying filter is clogged with hard water scale or dust. Clean the humidifying

filter, the tray and the water tank.

Also, humidity may not rise to the optimal level depending on the size or condition

of a room where the product is used.

In that case, set the fan speed to “MAX” or “MED”.

Why does the humidity level not increase during

humidifying operation?

The tap water is chlorinated and germs hardly develop.

If you use any water other than tap water (well water, water of water cleaner,

bottled mineral water etc.), mold or germs develop frequently, producing plenty of

scale and odors.

Carry out the maintenance frequently is required.

Do I have to use tap water?

Odor could come out from the air outlet through filters or other sections after the

unit in use is exposed to strong odor such as cigarette or BBQ smoke or if

saprophytic bacteria have propagated in residual water in the Humidifying Tray or

Water Tank.

Clean the HEPA Filter, Active Carbon & Silica Gel Deodorizing Filter, Humidifying

Filter, Humidifying Tray and Water Tank.

The air blowing out is smelly.

As the water draws heat from room when it is evaporated, the temperature of wind

becomes lower than room temperature. You may feel cold depending on the size

of the room.

(When the room temperature is 20°C and the humidity is 30%, the temperature of wind blowing out

from the air outlet is approximately 15°C)

The unit is designed to blow air toward a diagonally rear direction and a front direction

at the same time to efficiently deliver the high-density Plasmacluster Ion throughout a

room. You may feel cold depending on the location where the unit is placed.

(If you feel cold, change the location of the unit)

It seems that the unit is blowing out cold air.

E-16

～

page

E-16,17,20

page

• Press the Button to change settings as follows:

KC-JG20A(単ページ).indd 16 2016/10/12 10:17:41

ENGLISH

E-14

E-15

The operation will be automatically stopped as scheduled.

1 Hour 2 Hours 4 Hours 8 Hours OFF

Frequently Asked Questions

CONVENIENT FUNCTIONS

(Continued)

Check

(Within 3

seconds)

Select the

preferred time

Press for at least

3 seconds

Press for at least

3 seconds

Setting/Canceling Setting/Canceling

(In operation)

(While the timer is in operation)

OFF Timer

Beep

Beep Beep Beep Beep

Beep,

Beep

• The setting is automatically completed when no

operation is performed for 3 seconds.

(The OFF Timer Indicator Light will turn on)

• To turn off, change the setting to display “ (OFF)”.

(The OFF Timer Indicator Light will turn off.)

• It returns to the previous display in 3 seconds after the

setting is changed.

• The remaining time is displayed when pressing the

button once. (The time is rounded up to the nearest hour)

• If you press the OFF timer button while the remaining

time is displayed, you can change the setting time or turn

off the OFF timer.

(Example)

Remaining time: Over 3 hours and less than 4 hours

Sound Indicator Setting for Water Supply

(When the unit is OFF) (When the unit is OFF)

“Set” “Cancel”

Beep,

Beep

• When this setting is “ON”, the unit

generates an audible beep sound (for

about 10 seconds) while the Humidifying

Indicator Light is blinking.

• When the setting is “OFF”, the unit

generates no beep sound while the

Humidifying Indicator Light is blinking.

• If the unit is unplugged, this setting will be

cancelled and no beep sound will be

generated.

When the Humidifying Filter is moisturized, humid air will be discharged from air

outlet. Humidification is achieved without water-boiling, so steam or vapour cannot

be seen. It will not humidify the room excessively.

I do not see steam. Is it really humidifying? Doesn't

the product humidify the room too much?

Humidity may not rise to the optimal level when there is no water in the tank or the

humidifying filter is clogged with hard water scale or dust. Clean the humidifying

filter, the tray and the water tank.

Also, humidity may not rise to the optimal level depending on the size or condition

of a room where the product is used.

In that case, set the fan speed to “MAX” or “MED”.

Why does the humidity level not increase during

humidifying operation?

The tap water is chlorinated and germs hardly develop.

If you use any water other than tap water (well water, water of water cleaner,

bottled mineral water etc.), mold or germs develop frequently, producing plenty of

scale and odors.

Carry out the maintenance frequently is required.

Do I have to use tap water?

Odor could come out from the air outlet through filters or other sections after the

unit in use is exposed to strong odor such as cigarette or BBQ smoke or if

saprophytic bacteria have propagated in residual water in the Humidifying Tray or

Water Tank.

Clean the HEPA Filter, Active Carbon & Silica Gel Deodorizing Filter, Humidifying

Filter, Humidifying Tray and Water Tank.

The air blowing out is smelly.

As the water draws heat from room when it is evaporated, the temperature of wind

becomes lower than room temperature. You may feel cold depending on the size

of the room.

(When the room temperature is 20°C and the humidity is 30%, the temperature of wind blowing out

from the air outlet is approximately 15°C)

The unit is designed to blow air toward a diagonally rear direction and a front direction

at the same time to efficiently deliver the high-density Plasmacluster Ion throughout a

room. You may feel cold depending on the location where the unit is placed.

(If you feel cold, change the location of the unit)

It seems that the unit is blowing out cold air.

E-16

～

page

E-16,17,20

page

• Press the Button to change settings as follows:

KC-JG20A(単ページ).indd 17 2016/10/12 10:17:42

ENGLISH

• See the knack of detachment

(At the lower left of this page)

Gray side

E-16

E-17

When “Filter Maintenance Indicator Light” turns on

Back

Back Panel

Humidifying Filter

Indicates the time to clean the Water Tank, Humidifying Filter, Humidifying Tray, Back Panel and Sensor unit.

Sensor Unit

Water Tank

Humidifying Tray

Knack of detachment

Once a month

Wash

with water

Humidifying Filter / Humidifying Tray

Tank cap

Handle of

water tank

Float

Tray Partition

Roller

Back Panel / Sensor Unit

Back

Sensor Unit

(internal)

CARE AND MAINTENANCE

WARNING

Pull out the plug

Be sure to power OFF

and unplug the unit

before maintenance.

[Otherwise, electric shock and/or injury could result]

When the unit operates for 24 hours a day, the Indicator Light turns ON (Orange) in approximately a month (720 hours).

Be sure to clean

the unit to keep it

clean for use.

See page for cleaning when the parts are too dirty and smelly.

E-20

Humidifying Tray

Unplug

Detach the

Water Tank

and clean it.

Slightly lift up the

Humidifying Tray and then

pull it out. Clean the

Humidifying Filter and the

Humidifying Tray.

Reinstall the Humidifying

Filter, Humidifying Tray, and

Water Tank back to the unit.

• Be careful, do not spill out water

from the Humidifying Tray.

• Be sure to mount the

Humidifying Filter with the

correct side facing front.

(The gray side should face

the front)

• After cleaning, make sure to press the OFF timer button for at

least 3 seconds to reset it even if the Filter Maintenance Indicator

Light has not been on.

You will be notified of the next maintenance time about a month later (if the

unit is operated 24 hours a day)

Clean the Back Panel.

Detach the Back panel and

then clean the Sensor Unit.

Reinstall the Back Panel,

insert the plug into the socket,

and press the OFF timer

button for 3 seconds or more.

(The Filter Maintenance

Indicator Light turns off)

Press for

at least

3 seconds

Beep

Water Tank

<<Every time the

Water Tank is filled>>

Fill a small amount of water

into the Water Tank and

shake it for rinsing

the inside of the Tank

Caution

• Do not place the

tank with the tank

cap down.

(otherwise, water

leakage may occur)

• Do not shake the

Water

Tank by holding the

handle

Caution

• The Tray Partition is

attached loosely.

It is not a defect.

• Do not detach the Tray

Partition, Float and

Roller.

Caution

• Avoid applying

excessive force.

(Otherwise, the filters

may be damaged.)

• Remove the dust inside by a

vacuum cleaner through the

hole in the sensor unit.

(To prevent malfunctioning of

the sensor)

Rinse the

filter

with water

• Do not disassemble the filter frame

when cleaning Humidifying Filter.

Remove

dust by a

vacuum cleaner.

Caution

•

Drain water from the

Humidifying Tray periodically.

(Mold or saprophytic bacteria

could propagate resulting in

smelly odor)

Hold it up slightly

Pull out

KC-JG20A(単ページ).indd 18 2016/10/12 10:17:43

ENGLISH

• See the knack of detachment

(At the lower left of this page)

Gray side

E-16

E-17

When “Filter Maintenance Indicator Light” turns on

Back

Back Panel

Humidifying Filter

Indicates the time to clean the Water Tank, Humidifying Filter, Humidifying Tray, Back Panel and Sensor unit.

Sensor Unit

Water Tank

Humidifying Tray

Knack of detachment

Once a month

Wash

with water

Humidifying Filter / Humidifying Tray

Tank cap

Handle of

water tank

Float

Tray Partition

Roller

Back Panel / Sensor Unit

Back

Sensor Unit

(internal)

CARE AND MAINTENANCE

WARNING

Pull out the plug

Be sure to power OFF

and unplug the unit

before maintenance.

[Otherwise, electric shock and/or injury could result]

When the unit operates for 24 hours a day, the Indicator

Light turns ON (Orange) in approximately a month (720 hours).

Be sure to clean

the unit to keep it

clean for use.

See page for cleaning when the parts are too dirty and smelly.

E-20

Humidifying Tray

Unplug

Detach the

Water Tank

and clean it.

Slightly lift up the

Humidifying Tray and then

pull it out. Clean the

Humidifying Filter and the

Humidifying Tray.

Reinstall the Humidifying

Filter, Humidifying Tray, and

Water Tank back to the unit.

• Be careful, do not spill out water

from the Humidifying Tray.

• Be sure to mount the

Humidifying Filter with the

correct side facing front.

(The gray side should face

the front)

• After cleaning, make sure to press the OFF timer button for at

least 3 seconds to reset it even if the Filter Maintenance Indicator

Light has not been on.

You will be notified of the next maintenance time about a month later (if the

unit is operated 24 hours a day)

Clean the Back Panel.

Detach the Back panel and

then clean the Sensor Unit.

Reinstall the Back Panel,

insert the plug into the socket,

and press the OFF timer

button for 3 seconds or more.

(The Filter Maintenance

Indicator Light turns off)

Press for

at least

3 seconds

Beep

Water Tank

<<Every time the

Water Tank is filled>>

Fill a small amount of water

into the Water Tank and

shake it for rinsing

the inside of the Tank

Caution

• Do not place the

tank with the tank

cap down.

(otherwise, water

leakage may occur)

• Do not shake the

Water

Tank by holding the

handle

Caution

• The Tray Partition is

attached loosely.

It is not a defect.

• Do not detach the Tray

Partition, Float and

Roller.

Caution

• Avoid applying

excessive force.

(Otherwise, the filters

may be damaged.)

• Remove the dust inside by a

vacuum cleaner through the

hole in the sensor unit.

(To prevent malfunctioning of

the sensor)

Rinse the

filter

with water

• Do not disassemble the filter frame

when cleaning Humidifying Filter.

Remove

dust by a

vacuum cleaner.

Caution

•

Drain water from the

Humidifying Tray periodically.

(Mold or saprophytic bacteria

could propagate resulting in

smelly odor)

Hold it up slightly

Pull out

KC-JG20A(単ページ).indd 19 2016/10/12 10:17:44

ENGLISH

E-18

E-19

Main Unit

CARE AND MAINTENANCE

(Continued)

When heavily dirty

Main Unit / Louver

Do not rinse the main unit

with water.

HEPA Filter / Active Carbon & Silica Gel Deodorizing Filter

*Clean the Active Carbon & Silica Gel Deodorizing Filter and HEPA Filter at the same time

HEPA Filter

Tag

Never rinse the Filter with water.

(Otherwise, the filter will be damaged)

Caution

Vacuum softly

* Black powder of activated carbon may come off, but it is not a defect.

WARNING

Pull out the plug

Be sure to power OFF

and unplug the unit

before maintenance.

[Otherwise, electric shock and/or injury could result]

Unplug

Do not use the following:

Thinner

(Otherwise, damaged surfaces or malfunction may be

caused.)

Thinner

Benzine

Alcohol

Oven cleaner

Cleanser

Bleach

Spray detergent

Wire wool

Residential and

household

synthetic

detergent (alkaline)

Benzine

Bleach

Cleanser

Oven cleaner

Spray detergent

Synthetic

detergent

Deodorizing and de-formaldehyde 2-in-1 Filter

Vacuum the tagged

surface softly

• Maintain only the tagged surface.

Do not clean up the opposite surface.

(Otherwise, the filter will be damaged)

• Remove the dust attached to the surface of

filter.

• The filter is fragile. Be careful not to exert

strong force to it excessively.

• Both surfaces can be maintained.

• Remove the odor and dust on the filter.

•

Do not dry the filter under direct sunlight.

(Otherwise, the filter performance will

be degraded)

• Wipe off the heavy dirt with cloth

damped with cold or lukewarm water

(40 °C or less).

• Clean the casters as well.

Wipe the main unit

with soft cloth

Active Carbon & Silica

Gel Deodorizing Filter

Never rinse the Filter

with water.

(Otherwise, the filter will be damaged)

Please cover the ground with

newspapers when maintaining the filter.

When odor comes out from the air

outlet

When an odor is persisting

KC-JG20A(単ページ).indd 20 2016/10/12 10:17:44

ページが読み込まれています...

Sharp KC-JG20A 取扱説明書

ブランド: Sharp

モデル: KC-JG20A

タイプ: 取扱説明書

PDFをダウンロードします

報告

他の言語で

English: Sharp KC-JG20A Operating instructions

Sharp KC-JG20A 取扱説明書

Sharp KC-JG20A 取扱説明書

他の言語で

関連論文

その他のドキュメント