Samsung BD-H5500 ユーザーマニュアル

カテゴリー
ブルーレイプレーヤー
タイプ
ユーザーマニュアル
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Blu-ray
Disc Player
user manual
BD-H5500
ENGLISH
Safety Information
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates "dangerous
voltage" inside the product that presents
a risk of electric shock or personal injury.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol indicates important
instructions accompanying the product.
Do not install this equipment in a confined
space such as a bookcase or similar unit.
WARNING
To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
CAUTION
Blu-ray Disc Player USES AN INVISIBLE
LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE IF
DIRECTED. BE SURE TO OPERATE Blu-ray
Disc Player CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVERS
AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
This product satisfies CE regulations when
shielded cables and connectors are used
to connect the unit to other equipment.
To prevent electromagnetic interference
with electric appliances, such as radios
and televisions, use shielded cables and
connectors for connections.
IMPORTANT NOTE
The mains lead on this equipment is supplied
with a molded plug incorporating a fuse. The
value of the fuse is indicated on the pin face
of the plug.
If it requires replacing, a fuse approved to
BS1362 of the same rating must be used.
Never use the plug with the fuse cover omitted
if the cover is detachable. If a replacement fuse
cover is required, it must be of the same colour
as the pin face of the plug. Replacement
covers are available from your dealer.
If the fitted plug is not suitable for the power
points in your house or the cable is not long
enough to reach a power point, you should
obtain a suitable safety approved extension
lead or consult your dealer for assistance.
However, if there is no alternative to cutting
off the plug, remove the fuse and then safely
dispose of the plug. Do not connect the plug
to a mains jack, as there is a risk of shock
hazard from the bared flexible cord.
To disconnect the apparatus from the mains, the
plug must be pulled out from the mains socket,
therefore the mains plug shall be readily operable.
The product unit accompanying this user
manual is licenced under certain intellectual
property rights of certain third parties.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product. Use of controls,
adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
CAUTION :
• CLASS 3B VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN. AVOID
EXPOSURE TO THE BEAM (IEC 60825-1)
• THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND
DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
Precautions
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below.
Keep these operating instructions handy for
future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including AV receivers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where it exits the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
2
12. Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally, or
has been dropped.
Disc Storage & Management
• Holding Discs
- Fingerprints or scratches
on a disc may reduce
sound and picture quality
or cause skipping
- Avoid touching the surface of a disc
where data has been recorded.
- Hold the disc by the edges so that
fingerprints will not get on the surface.
- Do not stick paper or tape on the disc.
• Cleaning Discs
- If you get fingerprints or
dirt on a disc, clean it with
a mild detergent diluted in
water and wipe with a soft
cloth.
- When cleaning, wipe gently from the
inside to the outside of the disc.
• Disc Storage
`
Do not keep in direct sunlight.
`
Keep in a cool ventilated area.
`
Keep in a clean protection jacket and
store vertically.
Handling Cautions
• Do not expose this apparatus to dripping
or splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
• To turn this apparatus off completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.
• Do not plug multiple electric devices into
the same wall socket. Overloading a socket
can cause it to overheat, resulting in a fire
• Before connecting other components to
this player, be sure to turn them off.
• If you move your player suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and lens
and cause abnormal disc playback. If this
occurs, unplug the player, wait for two
hours, and then connect the plug to the
power outlet. Then, insert the disc, and try
to play back again.
• If the product makes an abnormal noise
or produces a burning smell or smoke,
turn off the power switch immediately and
disconnect the power plug from the wall
outlet. Then, contact the nearest customer
service centre for technical assistance. Do
not use the product. Using the product as
it is may cause a fire or an electric shock.
Using the 3D function
IMPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
• Some viewers may experience discomfort
while viewing 3D TV such as dizziness,
nausea, and headaches.
If you experience any such symptom,
stop viewing 3D TV, remove the 3D Active
Glasses, and rest.
• Watching 3D images for an extended
period of time may cause eye strain. If you
feel eye strain, stop viewing 3D TV, remove
your 3D Active Glasses, and rest.
• A responsible adult should frequently check
on children who are using the 3D function.
If there are any reports of tired eyes,
headaches, dizziness, or nausea, have the
child stop viewing 3D TV and rest.
• Do not use the 3D Active Glasses for other
purposes (Such as general eyeglasses,
sunglasses, protective goggles, etc.).
• Do not use the 3D function or 3D Active
Glasses while walking or moving around.
Using the 3D function or 3D Active Glasses
while moving around may cause you to
bump into objects, trip, and/or fall, and
cause serious injury.
• If you want to enjoy 3D content, connect
a 3D device (3D compliant AV receiver or
TV) to the player's HDMI OUT port using a
high-speed HDMI cable. Put on 3D glasses
before playing the 3D content.
• The player outputs 3D signals only through
HDMI cable connected to the HDMI OUT
port.
• As the video resolution in 3D play mode
is fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
• Some functions such as BD Wise, screen
size adjustment, and resolution adjustment
may not operate properly in 3D play mode.
• You must use a high-speed HDMI cable for
proper output of the 3D signal.
• Stay at least three times the width of the
screen from the TV when watching 3D
images. For example, if you have a 46-inch
screen, stay 138 inches (11.5 feet) from the
screen.
• Place the 3D video screen at eye level for
the best 3D picture.
• When the player is connected to some 3D
devices, the 3D effect may not function
properly.
• This player does not convert 2D content
into 3D.
• "Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of the Blu-ray Disc Association.
Copyright
© 2014 Samsung Electronics Co.,Ltd.
All rights reserved; No part or whole of this
user's manual may be reproduced or copied
without the prior written permission of
Samsung Electronics Co.,Ltd.
3
Contents Getting Started
Before using the User Manual
Disc Types and Contents your player can play
Media Disc Type Details
VIDEO
Blu-ray Disc
3D Blu-ray Disc
BD-ROM or BD-RE/-R recorded in the BD-RE format.
DVD-VIDEO
DVD-RW
DVD-R
DVD+RW
DVD+R
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have
been recorded and finalized, or a USB storage media containing DivX,
MKV or MP4 contents.
MUSIC
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing MP3 or WMA contents.
PHOTO
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing JPEG contents.
NOTES
`
The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
`
If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.
`
Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.
`
Your player will not play content that has been recorded on a BD-R or USB device at a bit rate that exceeds
25 Mbps.
`
Playback may not work for some types of discs, or when you use specific functions, such as angle change
and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to
this if necessary.
`
When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your player cannot play
• HD DVD
• DVD-ROM/PD/
MV, etc
• DVD-RAM
• Super Audio CD
(except CD layer)
•
DVD-RW (VR mode)
•
CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio
only, not graphics.)
• 3.9 GB DVD-R for
Authoring.
SAFETY INFORMATION
Warning ....................................................... 2
Precautions ................................................. 2
Disc Storage & Management ....................... 3
Handling Cautions ....................................... 3
Using the 3D function .................................. 3
Copyright .................................................... 3
GETTING STARTED
Before using the User Manual ......................4
Logos of Discs the player can play .............. 5
Accessories ................................................. 6
Front Panel .................................................. 7
Rear Panel ................................................... 7
Remote Control ........................................... 7
CONNECTIONS
Connecting to a TV ...................................... 8
Connecting to an Audio System .................. 8
Connecting to a Network Router ................. 9
SETTINGS
The Initial Settings Procedure....................... 9
Menu Navigation ..........................................9
Accessing the Settings Menu .................... 10
Display Settings ......................................... 10
Audio Settings ........................................... 11
Network Settings ....................................... 12
System Settings ........................................ 13
Language Settings .....................................14
Security Settings........................................ 14
General Settings ........................................ 14
Support Settings .......................................14
MEDIA PLAY
Playing a Commercially Recorded Disc ...... 15
Playing Files on a USB Device ................... 15
Playing a Disc with User Recorded
Content ..................................................... 16
Playing Content Located on Your PC or
DLNA Device through the Blu-ray
Disc Player
................................................. 16
Controlling Video Playback ........................ 17
Controlling Music Playback ........................ 17
Playing Photo Contents ............................. 19
APPENDIX
Troubleshooting ......................................... 19
Specifications ............................................ 21
4
Region Code
Both players and discs are coded by region.
These regional codes must match for a disc
to play. If the codes do not match, the disc
will not play.
The Region Number for this player is
displayed on the rear panel of the player.
Disc
Type
Region
Code
Area
Blu-ray
Disc
A
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia, Central
and South Asia.
DVD-
VIDEO
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
North Korea, Mongolia
6
China
Logos of Discs the player can play
Blu-ray Disc BD-LIVE
3D Blu-ray Disc DivX
PAL broadcast System in U.K., France, Germany,
etc.
Supported File Formats
Notes on the USB connection
• Your player supports USB storage media,
MP3 players, digital cameras, and USB
card readers.
• The player does not support folder or file
names longer than 128 characters.
•
Some USB/External HDD/digital camera
devices may not be compatible with the player.
• Your player supports the FAT16, FAT32,
and NTFS file systems.
•
Connect USB devices directly to the player’s
USB port. Connecting through a USB cable
may cause compatibility problems.
• Inserting more than one memory device
into a multi-card reader may cause the
reader to operate improperly.
•
The player does not support the PTP protocol.
• Do not disconnect a USB device during a
"loading" process.
• The bigger the image resolution, the longer
the image takes to display.
This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from commercial
sites.
Your player only supports video with a frame rate under 30fps (frames per second).
Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives and USB
HDD. (HUB is not supported.)
Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with this player.
If some USB devices require excessive power, they may be limited by the circuit safety device.
If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a wall
socket.
If the problem continues, contact the USB HDD manufacturer.
SAMSUNG is not responsible for any data file damage or data loss.
Your player does not support NTFS compressed files, sparse files, or encrypted files.
You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)
Video File Support
File Extension Container Video Codec Audio Codec Resolution
*.avi
AVI
DivX 3.11/4/5/6
MP3
Dolby Digital
DTS
WMA
PCM
1920x1080
MP4v3
H.264 BP/MP/HP
1920x1080
*.mkv
MKV
VC-1 AP MP3
Dolby Digital
DTS
1920x1080
H.264 BP/MP/HP
1920x1080
*.wmv
WMV (wmv9)
VC-1 AP
WMA
1920x1080
VC-1 SM
1920x1080
*.mp4
MP4
MP4 (mp4v)
AAC
1920x1080
H.264 BP/MP/HP
1920x1080
*.mpg
*.mpeg
PS
MPEG1
MP1, 2
Dolby Digital
DTS
1920x1080
MPEG2
1920x1080
H.264 BP/MP/HP
1920x1080
*.rmvb
RMVB
RV8/9/10
RV30/40
RealAudio 6
1920x1080
5
Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be
played if its content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file
itself is corrupted.
- Files having a higher Bit rate/frame rate than standard may stutter during sound/video playback.
- The Seek (skip) function is not available if the file’s index table is damaged.
- Depending on your country, RMVB format may not be supported.
Video decoder
- Supports up to H.264 Level 4.1 and AVCHD
- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4
- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
- Does not support GMC 2 or higher
Audio decoder
- Supports WMA 7, 8, 9 and STD
- Does not support WMA sampling rate of 22050Hz mono.
- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)
Max bit rate: 320kbps
Supported DivX subtitle file formats
*.ttxt, *.smi, *.srt, *.sub, *.txt
NOTES
`
Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution and
frame rate.
Music File Support
File Extension Container Audio Codec Support Range
*.mp3
MP3 MP3
-
*.wma
WMA WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates from 5kbps to 355kbps
Picture File Support
File Extension Type Resolution
*.jpg
*.jpeg
*.jpe
JPEG
15360x8640
*.png
PNG
15360x8640
AVCHD (Advanced Video Codec High Definition)
• This player can play back AVCHD format discs. These discs are normally recorded and used
in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the
conventional image compressing format.
• Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that
use "x.v.Color" format.
• "x.v.Color" is a trademark of Sony Corporation.
• "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.
and Sony Corporation.
NOTES
`
Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
`
"x.v.Color" offers a wider colour range than normal DVD camcorder discs.
Accessories
Check for the supplied accessories shown below.
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
HDMI Cable
Batteries for Remote
Control (AAA Size)
User Manual Remote Control
6
Front Panel
USB HOST
REMOTE CONTROL SENSOR
DISC TRAY
PLAY/PAUSE BUTTON
STOP BUTTON
POWER BUTTON
OPEN/CLOSE BUTTON
NOTES
`
When the player displays the Blu-ray Disc menu, you cannot start the movie by pressing the Play button
on the player or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and
then press the
v
button.
`
You can perform software upgrades using the USB Host jack with a USB flash memory stick only.
Rear Panel
HDMI OUT LAN DIGITAL AUDIO OUT
Remote Control
Tour of the Remote Control
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
Turn the player on and off.
Allows you to repeat A-B disc.
Press numeric buttons to operate options.
Press to open and close the disc tray.
Use to enter the disc menu.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use bonusview function.
Return to the previous menu.
These buttons are used both for menus on the
player and also several Blu-ray Disc functions.
Use to select menu items and change menu
values.
Press to use Tools menu.
Use to access various audio functions on a
disc (Blu-ray Disc/DVD).
Press to play a disc.
Press to pause a disc.
Turn the TV on and off.
Press to switch the Blu-ray Disc/DVD's
subtitle language.
Use to enter the popup menu/title menu.
Press to search a disc backwards or
forwards.
Press to move to the home menu.
Press to see the full screen on a TV.
During the bluray disc/DVDs playback, this
button does not operate.
Press to exit the menu.
Use to display the playback information.
Allows you to repeat a title, chapter, track or
disc.
TV volume adjustment.
After setup, allows you to set the input
source on your TV.
Installing batteries
NOTES
`
If the remote does not operate properly:
•
Check the polarity (+/–) of the batteries.
•
Check if the batteries are drained.
•
Check if the remote sensor is blocked by obstacles.
•
Check if there is any fluorescent lighting nearby.
!
CAUTION
`
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash
`
Do not dispose of batteries in a fire.
`
Do not short circuit, disassemble or overheat the batteries.
`
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
7
Connections
Connecting to a TV
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your TV.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Audio
Video
NOTES
`
If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio
Out on the player to an audio system to hear audio.
`
An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.
`
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of
your TV.
`
When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the
first time, the player automatically sets the HDMI output resolution to the highest supported by the TV.
`
A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Colour to Off in the menu.
`
To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.
`
HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on
the screen.
Connecting to an Audio System
You can connect the Blu-ray player to an audio system using one of the methods illustrated
below.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Method 1 Connecting to an HDMI supported AV receiver
• Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your receiver.
• Best quality (Recommended)
Method 2 Connecting to an AV receiver with Dolby Digital or a DTS decoder
• Using a digital Coaxial cable (not supplied), connect the Coaxial Digital Audio Out jack on the
product to the Digital Coaxial In jack of the receiver.
• Good quality
• You will hear sound only through the front two speakers with Digital Output set to PCM.
AudioAudio
Method 2Method 1
8
Connecting to a Network Router
You can connect your player to your network router using one of the methods illustrated below.
To use the DLNA network functionality, you must connect your PC to your network as shown
in the illustrations.
Wired Network
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband
modem
Router
Or
NOTES
`
Internet access to Samsung's software update server may not be allowed, depending on the router you use or your
ISP's policy. For more information, contact your ISP (Internet Service Provider).
`
DSL users, please use a router to make a network connection.
Settings
The Initial Settings Procedure
• The Home screen will not appear if you do not
configure the initial settings.
• The OSD (On Screen Display) may change in this
player after you upgrade the software version.
• The access steps may differ depending on the
menu you selected.
• After the initial settings process is complete
, the
panel buttons and remote control can be operated.
After you have connected the player to your
TV, turn on the TV and player. When you turn
on the player the first time, the player's Initial
Settings screen appears on the TV. The Initial
Setting procedure lets you set the On Screen
Display (OSD) and menu languages, the
aspect ratio (screen size), the network type,
and connect the player to your network.
NOTES
`
The Home menu will not appear if you do not
configure the initial settings except as noted
below.
`
If you press the BLUE (D) button during
network setup, you can access the Home menu
even if the network setup is not completed yet.
`
When you return to the Home menu, the full
screen mode is cancelled automatically.
`
If you want to display the Initial Setting screen
again to make changes, press the
@
button
on the top panel of the player for more than 5
seconds with no disc inserted. This resets the
player to its default settings.
`
After the initial settings process is complete.
you can operate the HDMI-CEC function.
`
If you want to use the Anynet+(HDMI-CEC)
function to aid in the initial set up process,
please follow the instructions below.
1) Connect the player to an Anynet+(HDMI-
CEC) compliant Samsung TV using HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On in
both the TV and the player.
3) Set the TV to the Initial Settings Procedure.
`
If you leave the player in the stop mode for
more than 5 minutes without using it, a screen
saver will appear on your TV. If the player is
left in the screen saver mode for more than 25
minutes, the power will automatically turn off.
Menu Navigation
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
4
3
1
HOME Button : Press to move to the Home
menu.
2
RETURN Button :
Return to the previous menu.
3
v
(Enter) / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
4
EXIT Button : Press to exit the current menu.
9
`
Depending on the content and the position of
the picture on your TV screen, you may see
vertical black bars on the left side, right side,
or both sides.
TV Aspect Ratio
Depending on the type of television you have,
you may want to adjust the screen size setting.
NOTES
`
Depending on the disc type, some aspect
ratios may not be available.
`
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
the picture might appear to be distorted.
BD Wise (Samsung TVs only)
BD Wise is Samsung’s latest inter-connectivity
feature.
When you connect a Samsung player and a
Samsung TV with BD Wise to each other via
HDMI, and BD Wise is on in both the player
and TV, the player outputs video at the video
resolution and frame rate of the Blu-ray Disc/
DVDs.
NOTES
`
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
`
If the player is connected to a device that does not
support BD Wise, you cannot use the BD Wise function.
`
For proper operation of BD Wise, set the BD
Wise menu of both the player and the TV to On.
Resolution
Lets you set the output resolution of the HDMI
video signal to Auto, 1080p, 1080i, 720p or
576p/480p. The number indicates the number
of lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively.
The more lines, the higher the quality.
Resolution according to the output
mode
• Blu-ray Disc/E-contents/Digital Contents
playback
Output
Setup
HDMI / connected
HDMI Mode
Blu-ray Disc
E-contents/
Digital
contents
BD Wise
Resolution of
Blu-ray Disc
1080p
Auto
Max. Resolution
of TV input
Max. Resolution
of TV input
1080p@60F
(Movie Frame : Off)
1080p@60F 1080p@60F
Movie Frame :
Auto (24 fps)
1080p@24F 1080p@24F
1080i 1080i 1080i
720p 720p 720p
576p/480p 576p/480p 576p/480p
• Home Menu
App 1 App 2 App 3 App 4
App 5
More
Change Device
Settings
Play disc Photos Videos Music
No disc
2
3
6
5
7
1
4
8
1
Selects Videos.
2
Selects Music.
3
Selects Settings.
4
Selects Change Device.
5
Selects Photos.
6
Selects Play disc.
7
Selects applications.
8
Selects More applications.
NOTES
`
The Videos, Photos, and Music options require
that you have an appropriate disc inserted into
the player or a USB flash device attached to
the player.
Accessing the Settings Menu
To access the Settings menu and sub-menus,
follow these steps:
1. Press the POWER button.
The Home Menu appears.
2.
Press the
▲▼
◄► buttons to select
Settings, and then press the
v
button.
3. Press the ▲▼ buttons to select the
desired submenu, and then press the
v
button.
4.
Press the ▲▼ buttons to select the desired
item, and then press the
v
button.
5. Press the EXIT button to exit the menu.
NOTES
`
The access steps may differ depending on
the menu you selected. The OSD (On Screen
Display) may change in this player after you
upgrade the software version.
Display Settings
You can configure various display options
such as the TV Aspect Ratio, Resolution, etc.
3D Settings
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
NOTES
`
For some 3D discs, to stop a movie during 3D
playback, press the
5
button once.
The movie stops and the 3D mode option is
de-activated.
To change a 3D option selection when you are
playing a 3D movie, press the
5
button once.
The Blu-ray menu appears. Press the
5
button again, then select 3D Settings in the
Blu-ray menu.
10
• DVD playback
Output
Setup
HDMI / connected
HDMI Mode
BD Wise 576i/480i
Auto Max. Resolution of TV input
1080p 1080p
1080i 1080i
720p 720p
576p/480p 576p/480p
NOTES
`
If the TV you connected to the player does not
support Movie Frame or the resolution you
selected, the message "If no pictures are shown
after selecting ‘Yes’, please wait for 15 seconds
to return to the previous resolution. Do you
want to change the resolution?" appears. If you
select Yes, the TV’s screen will go blank for 15
seconds, and then the resolution will revert to
the previous resolution automatically.
`
If the screen stays blank after you have
changed the resolution, remove all discs, and
then press and hold the
@
button on the top of
the player for more than 5 seconds. All settings
are restored to the factory default. Follow the
steps on the previous page to access each
mode and select the Display Setup that your TV
will support.
`
When the factory default settings are restored,
all stored user BD data is deleted.
`
The Blu-ray Disc must have the 24 frame feature
for the player to use the Movie Frame (24
fps
)
mode.
Movie Frame (24 fps)
Setting the Movie Frame (24 fps) feature to
Auto allows you to adjust the player’s HDMI
output to 24 frames per second for improved
picture quality.
You can enjoy the Movie Frame (24 fps)
feature only on a TV supporting this frame
rate. You can select Movie Frame only when
the player is in the HDMI 1080p output
resolution modes.
HDMI Colour Format
Lets you set the colour space format for
HDMI output to match the capabilities of the
connected device (TV, monitor, etc).
HDMI Deep Colour
Lets you output video from the HDMI OUT jack with
Deep Colour. Deep Colour provides more accurate
colour reproduction with greater colour depth.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
Audio Settings
Digital Output
Lets you select the digital audio output format
that is suitable for your TV or AV Receiver. For
more details, please refer to the Digital Output
Selection table.
Digital Output Selection
Setup PCM
Bitstream
(Unprocessed)
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
Connection
HDMI
Receiver
Coaxial
HDMI
Receiver
Coaxial
HDMI Receiver or
Coaxial
HDMI supported
AV receiver or
Coaxial
Audio Stream
on Blu-ray
Disc
PCM Up to 7.1ch PCM 2ch PCM PCM 2ch Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital Plus PCM 2ch PCM 2ch
Dolby Digital
Plus
Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby TrueHD PCM 2ch PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD High
Resolution Audio
PCM 2ch PCM 2ch
DTS-HD High
Resolution
Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD Master
Audio
PCM 2ch PCM 2ch
DTS-HD
Master Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
Audio Stream
on DVD
PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Dolby Digital Dolby Digital
DTS PCM 2ch PCM 2ch DTS DTS DTS DTS
Definition for
Blu-ray Disc
Any
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio and add
Navigation Sound Effects.
Outputs only main feature
audio stream so that your
AV receiver can decode the
audio bitstream.
You will not hear BONUSVIEW
audio and Navigation Sound
Effects.
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio
and add Navigation
Sound Effects, then
re-encodes the
PCM audio into DTS
bitstream
Decodes main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and add
Navigation Sound
Effects, then re-
encodes the PCM
audio into Dolby
Digital bitstream
* If Source Stream is 2ch, "Re-encoded Dolby D" Settings are not applied.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack of the main feature.
- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.
- Navigation Sound Effects : When you choose a menu navigation selection, a Navigation
Sound Effect may sound. Navigation Sound Effects are different on each Blu-ray Disc.
11
NOTES
`
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
`
If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
`
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
`
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
`
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
`
If your TV is not compatible with compressed
multi-channel formats (Dolby Digital, DTS), the
player may output PCM 2ch downmixed audio
even though you selected Bitstream (either Re-
encoded or Unprocessed) in the setup menu.
`
If your TV is not compatible with PCM sampling
rates over 48kHz, the player may output 48kHz
downsampled PCM audio even though you set
PCM Downsampling to Off.
PCM Downsampling
Lets you choose to have 96KHz PCM signals
downsampled to 48KHz before they are
outputted to an amplifier. Choose On if your
amplifier or receiver is not compatible with a
96KHz signal.
Wired Network Settings
1. In the Home menu, press the ▲▼ ◄►
buttons to select Settings, and then
press the
v
button.
2. Press the ▲▼ buttons to select Network,
and then press the
v
button.
3. Press the ▲▼ buttons to select Wired
Network Settings, and then press the
v
button. The Wired Network Settings
screen appears.
Display
Audio
Network
System
Language
Security
General
Support
Settings
Wired Network Settings
Internet Protocol Setup : Auto
\
IP Address :
0
0
0
0
Subnet Mask :
0
0
0
0
Gateway :
0
0
0
0
DNS : Auto
DNS Server :
0
0
0
0
>
Move
"
Select
'
Return
4. In the Internet Protocol Setup field, select
Auto if it is not selected. (Press
v
select
Auto, and then press
v
.)
5. The Auto Function acquires and fills in the
values for IP Address, Subnet Mask,
etc., automatically.
NOTES
`
This process can take up to five minutes.
6. After the Network Function has acquired
the network values, press the RETURN
button.
7. Select Network Test, and then press
v
to ensure the player has connected to
your network.
8. When the Network Test is complete, press
the RETURN twice to return to the Main
Menu.
9. If the Network Function does not acquire
the network values, go to the directions
for Manual Setup.
Manual Network Settings
Before you start manual network setup, you
need the network setting values.
To enter the Network Settings into your
player, follow these steps:
1. In the Home menu, press the ▲▼ ◄►
buttons to select Settings, and then
press the
v
button.
2. Press the ▲▼ buttons to select Network,
and then press the
v
button.
3. Press the ▲▼ buttons to select Wired
Network Settings, and then press the
v
button. The Wired Network Settings
screen appears.
4. Select the Internet Protocol Setup field,
and then press the
v
button.
5. Press the ▲▼ buttons to select Manual,
and then press the
v
button.
6. Press the ▼ button to go to the first entry
field (IP Address).
7. Use the number buttons on your remote
to enter numbers.
8. When done with each field, use the ►
button to move to the next field. You can
also use the other arrow buttons to move
up, down, and back.
9. Enter the IP Address, Subnet Mask, and
Gateway values in the same way.
10. Press the ▼ button to go to DNS.
11. Press the ▼ button to go to the first DNS
entry field.
12. Enter the numbers as above.
Dynamic Range Control
Lets you apply dynamic range control to
Dolby Digital, Dolby Digital Plus, and Dolby
True HD audio.
• Auto : Automatically controls the dynamic
range of Dolby TrueHD audio, based
on information in the Dolby TrueHD
soundtrack.
Also turns dynamic range control on for
Dolby Digital and Dolby Digital Plus.
• Off :
Leaves the dynamic range uncompressed,
letting you hear the original sound.
• On : Turns dynamic range control on for
all three Dolby formats. Quieter sounds
are made louder and the volume of loud
sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix
method that is compatible with your stereo
system. You can choose to have the player
downmix to normal stereo or to surround
compatible stereo.
Network Settings
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic
- and most are - we recommend using the
Auto procedure for network setup. This is
easiest and will work in the majority of cases.
If it is static, you must use the manual set up
procedure.
Network setup directions start below.
NOTES
`
This unit can only be connected to a Network
via a wired connection.
12
13. Press the RETURN button on your
remote.
14. Run a Network Test to ensure the player
has connected to your network.
Network Test
Use this menu item to check whether your
network connection is working or not.
Network Status
Use to check whether a connection to a
network and the Internet has been established.
Device Name
Device Name function allows you to change
player's name by selecting from device name
list box.
BD-Live Internet Connection
Set to allow or prohibit an Internet connection
when you use the BD-LIVE service.
• Allow (All) : The Internet connection is
allowed for all BD-LIVE contents.
• Allow (Valid Only) : The Internet
connection is allowed only for BD-LIVE
contents containing a valid certificate.
• Prohibit : No Internet connection is allowed
for any BD-LIVE content.
NOTES
`
What is a valid certificate?
When the player uses BD-LIVE to send the
disc data and a request to the server to certify
the disc, the server uses the transmitted data
to check if the disc is valid and sends the
certificate back to the player.
`
The Internet connection may be restricted
while you are using BD-LIVE contents.
Using BD-LIVE™
Once the player is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1.
Attach a USB memory stick to the USB jack
on the front of the player, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
2.
Insert a Blu-ray Disc that supports BD-LIVE.
3. Select an item from various BD-LIVE
service contents provided by the disc
manufacturer.
NOTES
`
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
The DLNA Function
DLNA lets you play music, video, and photo
files located in your PC or NAS on the player.
To use DLNA with your player, you must
connect the player to your network.
(See page 12-13).
To use DLNA with your PC, you must install
DLNA software on your PC.
If you have NAS, you can use DLNA without
any additional software.
To download DLNA software
1. Go to Samsung.com
2. Click Support, enter your player’s product
number in the field that appears, and then
click Product.
3. On the next screen, click Get downloads
under Downloads.
4. Click Software on the next page.
5. Click the icon in the DLNA line under File
to start the download.
System Settings
Initial Settings
By using the Initial Settings function, you can
set the language, Network Settings, etc.
For more information about the Initial Settings
function, refer to the Initial Settings section of
this user manual (See page 9).
Quick Start
You can turn on the power quickly by
decreasing the boot time.
NOTES
`
If this function is set to On, Standby power
consumption will be increased.
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers
linked operations with other Samsung players
that have the Anynet+ feature.
To operate this function, connect this player to
an Anynet+ Samsung TV with an HDMI cable.
With Anynet+ on, you can operate this player
using a Samsung TV remote control and start
disc playback simply by pressing the PLAY
( ) button on the TV’s remote control.
For more information, please see the TV user
manual.
NOTES
`
This function is not available if the HDMI cable
does not support CEC.
`
If your Samsung TV has an Anynet+ logo, then
it supports the Anynet+ function.
`
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
`
After the product was turned off, disconnecting
and connecting the power cable turns it on
automatically. At the moment, it automatically
turns off in about 15 seconds for re-
establishing Anynet+ connection.
`
For some TV products, if connected to this
product with Anynet+ function, turning the
TV on may display a warning popup message
saying no connection was found. Still, Anynet+
connection is properly established and
available to use.
13
BD Data Management
Enables you to manage the downloaded
contents you accessed through a Blu-ray disc
that supports the BD-LIVE service and stored
on a flash drive.
You can check the device’s information
including the storage size, delete the BD data,
or change the Flash memory device.
NOTES
`
In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
`
Your player supports the FAT16, FAT32, and
NTFS file systems. We recommend you use
USB devices that support USB 2.0 protocol
with 4 MB/sec or faster read/write speed.
`
The Resume Play function may not work after
you format the storage device.
`
The total memory available to BD Data
Management may differ, depending on the
conditions.
DivX® Video On Demand
View DivX® VOD Registration Codes to
purchase and play DivX® VOD contents.
Language Settings
You can select the language you prefer for
the On-Screen menu, disc menu, audio, and
subtitles.
NOTES
`
The selected language will only appear if it is
supported on the disc.
Security Settings
The default security PIN is 0000. Enter the
default PIN to access the security function if you
haven't created your own PIN. After you have
accessed the security function for the first time,
change the PIN using the Change PIN function.
BD Parental Rating
Prevents playback of Blu-ray Discs with
specific age ratings unless the 4 digit PIN is
entered.
DVD Parental Rating
This function works in conjunction with DVDs
that have been assigned an age rating or
numeric rating that indicates the maturity level
of the content. These numbers help you control
the types of DVDs that your family can watch.
Select the rating level you want to set.
For example, if you select Level 6, discs rated
above 6 - Level 7 and 8 - will not play.
A larger number indicates more mature content.
Change PIN
Change the 4-digit password used to access
security functions.
If you forget your password
1. Remove any discs.
2. Press and hold the
@
button on the top
panel for 5 seconds or more.
All settings will revert to the factory settings.
NOTES
`
When the factory default settings are restored,
all the user stored BD data will be deleted.
General Settings
Time Zone
Lets you specify the time zone that is
applicable to your area.
Support Settings
Software Upgrade
The Software Upgrade menu allows you to
upgrade the player’s software for performance
improvements or additional services.
By Online
To upgrade By Online, follow these steps:
1. In the player’s menu, go to Settings >
Support > Software Upgrade.
2. Select By Online, and then press the
v
button. The Connecting to Server
message appears.
3. A popup message will appear if an update
is available.
4.
If you select Yes, download process started.
(Never turn the player on during an upgrade.)
5. When the update is completed, the player
will restart automatically.
NOTES
`
The upgrade is complete when the player turns
off, and then turns on again by itself.
`
Never turn the player off or back on manually
during the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused by
an unstable Internet connection or consumer
negligence during a software upgrade.
`
No disc should be in the product when you
upgrade the software By Online.
By USB
To upgrade by USB, follow these steps:
1. Visit www.samsung.com/bluraysupport.
2. Download the latest USB software
upgrade zip archive to your computer.
3. Unzip the zip archive to your computer.
You should have a single RUF file with the
same name as the zip file.
4. Copy the RUF file to a USB flash drive.
5. Make sure there is no disc in the player,
and then insert the USB flash drive into
the USB port of the player.
6. In the player’s menu, go to Settings >
Support > Software Upgrade.
7. Select By USB.
NOTES
`
No disc should be in the product when you
upgrade the software using the USB Host jack.
`
When the software upgrade is done, check the
software details in the software Upgrade menu.
`
Do not turn off the player during the software
upgrade. It may cause the player to malfunction.
`
Software upgrades using the USB Host jack
must be performed with a USB flash memory
stick only.
14
Auto Upgrade Notification
If you have connected the player to your
network, and then set Auto Upgrade
Notification on, the player automatically
notifies you when a new software version is
available for the player.
To set Auto Upgrade Notification on, follow
these steps:
1. Select Auto Upgrade Notification, and
then press the
v
button.
2. Use the ▲▼ buttons to select On, and
then press the
v
button.
If there is a new software version available,
the player notifies you with a popup message.
1. To upgrade the firmware, select Yes in the
Pop-up. The player turns off automatically,
then restarts, and begins the download.
(Never turn the player on or off manually
during an upgrade.)
2. The update progress popup appears.
3. When the update is completed, the player
will restart automatically.
NOTES
`
The upgrade is complete when the player turns
off, and then turns on again by itself.
`
Never turn the player off or on manually during
the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused by
an unstable Internet connection or consumer
negligence during software upgrade.
Contact Samsung
Provides contact information for assistance
with your player.
Terms of Service Agreement
Lets you view the general disclaimer regarding
third party contents and services.
Reset
Returns all settings to their factory defaults
except for the network settings.
Media Play
Playing a Commercially Recorded
Disc
1. Press the
8
button to open the disc tray.
2. Place a disc gently into the disc tray with
the disc's label facing up.
3. Press the
8
button to close the disc tray.
Playback starts automatically.
Playing Files on a USB Device
There are two methods you can use to play or
view multimedia files located on a USB device
through your player.
Method 1
1. Turn the player on.
2. Connect the USB device to the USB port
on the front panel of the player. The New
Device Connected pop-up appears.
App 1 App 2 App 3 App 4 App 5
More
Change Device
Settings
Play disc Photos Videos Music
No disc
New device connected.
Photos
Videos
Music
123
>
Move
"
Enter
'
Return
NOTES
`
If the pop-up does not appear, go to Method 2.
3. Use the ▲▼ buttons to select Photos,
Videos or Music, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Photos, Videos &
Music screen and going to Step 3 in Method 2
below.
4. If necessary, use the ▲▼◄► buttons to
select a folder, and then press the
v
button.
5. Select a file to view or play, and then
press the
v
button.
6. Press the RETURN button to exit a folder
or the EXIT button to return to the Home
screen.
7. Go to pages 17~19 for instructions that
explain how to control playback of videos,
music, and pictures on a USB device.
15
4. If necessary, use the ▲▼◄►buttons to
select a folder, and then press the
v
button.
5. Use the ◄►▲▼ buttons to select a file
to view or play, and then press the
v
button.
6. Press the RETURN button one or more
times to exit a current screen, exit a folder,
or to return to the Home screen. Press the
EXIT button to return directly to the Home
Screen.
7. Go to pages 17~19 for instructions that
explain how to control playback of videos,
music, and pictures on a disc.
Playing Content Located on Your
PC or DLNA Device through the
Blu-ray Disc Player
DLNA Connection
PC Blu-ray Disc Player
Play back PC's
files
1. Connect the Blu-ray Disc Player, your PC,
and/or your DLNA compatible device to
the same network.
2. Follow the directions in the DLNA software
Installation/Instruction manual to set up
devices and files for playing or viewing.
3. Select Change Device on the player's
Home screen, and then press the
v
button. In the list of DLNA connected
devices that appears, select your PC or
other DLNA compatible device, and then
press the
v
button.
4. Use the ◄► buttons to select the type
of content you want to view or play -
Videos, Photos, or Music - and then
press the
v
button.
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 4. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Home screen and
repeating Step 4.
5. A screen appears listing the contents of
the disc. Depending on how the contents
are arranged, you will see either folders,
individual files, or both.
6. If necessary, use the ▲▼◄►buttons to
select a folder, and then press the
v
button.
7. Use the ◄►▲▼ buttons to select a file
to view or play, and then press the
v
button.
8. Press the RETURN button one or more
times to exit a current screen, exit a folder,
or to return to the Home screen. Press the
EXIT button to return directly to the Home
Screen.
9. Go to pages 17~19 for instructions that
explain how to control playback of videos,
music, and pictures on a disc.
Method 2
1. Turn the player on.
2. Connect the USB device to the USB port
on the front panel of the player. Select
Change Device and then press the ▲▼
button to select USB. Press the
v
button.
App 1 App 2 App 3 App 4 App 5
More
Change Device
Settings
Play disc Photos Videos Music
No disc
Change Device
No Disc
123
a
Close
3. Use the ▲▼◄► buttons to select
Photos, Videos or Music on the Home
screen, and then press the
v
button.
The Photos, Videos & Music screen
appears listing the content of the device.
Depending on how the contents is
arranged, you will see either folders,
individual files, or both.
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Photos, Videos &
Music screen and repeating Step 3.
4. If necessary, use the ▲▼◄► buttons to
select a folder, and then press the
v
button.
5. Use the ▲▼◄► buttons to select a file
to view or play, and then press the
v
button.
6. Press the RETURN button to exit a folder
or the EXIT button to return to Home
screen.
7. Go to pages 17~19 for instructions that
explain how to control playback of videos,
music, and pictures on a USB device.
NOTES
`
If you insert a disc when playing a USB
device, the device mode changes to "Disc"
automatically.
Playing a Disc with User Recorded
Content
You can play multimedia files you have
recorded on Blu-ray, DVD, or CD discs.
1. Place a user recorded disc into the disc
tray with the disc’s label facing up, and
then close the tray.
2. Use the ◄► buttons to select the type
of content you want to view or play -
Videos, Photos, or Music - and then
press the
v
button.
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 2. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Home screen and
repeating Step 2.
3. A screen appears listing the contents of
the disc. Depending on how the contents
are arranged, you will see either folders,
individual files, or both.
16
Controlling Video Playback
You can control the playback of video content
located on a Blu-ray disc, DVD, CD, USB
device, or your computer. Depending on the
media, some of the functions described in this
manual may not be available.
During Blu-ray or DVD disc playback, the Full
screen button does not operate.
Buttons on the Remote Control
used for Video Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
Playback related buttons
The player does not play sound in Search,
Slow or Step mode.
• To return to normal speed playback, press
the
6
button.
6
button
Starts playback.
5
button
Stops playback.
7
button
Pauses playback.
Fast Motion
Play
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button, the playback speed
will change.
Slow Motion
Play
In pause mode, press the
4
button.
Each time you press the
4
button, the playback speed will
change.
Step Motion
Play
In pause mode, press the
7
button.
Each time you press the
7
button, a new frame appears.
Skip Motion
Play
During playback, press the
1
or
2
button.
Each time you press the
1
or
2
button, the disc moves to the
previous or next chapter or file.
Using the disc menu, title menu,
popup menu, and title list
DISC MENU
button
During playback, press this button
to start the disc menu function.
TITLE MENU
button
During playback, press this button
to start the title menu function.
POPUP MENU
button
During playback, press this button
to start the popup menu function.
Controlling Music Playback
You can control the playback of music located
on a Blu-ray disc, DVD, CD, USB device, or
your computer.
Buttons on the Remote Control
used for Music Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
4
6
3
2
5
1
NUMBER buttons (Audio CD (CD-DA) only) :
During Playlist playback, press the desired
track number.
The selected track is played.
2
Skip : During playback, press the
1
or
2
button to move to the previous or next file of
the playlist.
3
5
button : Stops a track.
4
Fast Play (Audio CD (CD-DA) only)
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button,
the playback speed will change.
5
Pause : Pauses a track.
6
6
button : Plays the currently selected
track.
Repeat an Audio CD (CD-DA)/
MP3
1. During Playlist playback, press the
TOOLS button.
"
Pause c Select Tools
'
Return
+
00:08 / 05:57
1/6
TRACK 001
05:57
TRACK 002
04:27
TRACK 003
04:07
TRACK 004
03:41
TRACK 005
03:17
TRACK 006
03:35
Playlist
TRACK 001
CD
Tools
Repeat Mode ? Off \
Rip
>
Move
<
Adjust
'
Return
2. Press the ◄► buttons to select Track,
All, Shuffle, or Off.
3. Press the
v
button.
Off
Songs are played in the order
in which they were recorded.
(
) Track
The current song is repeated.
(
) All
All songs are repeated.
(
) Shuffle
Shuffle plays songs in random
order.
17
Playlist
1. To move to the Music List, press the
5
or RETURN button.
The Music List screen appears.
c
Select Tools
( )
Jump to Page
'
Return
1/2 Page
Music
TRACK 001
TRACK 001
02:38
TRACK 003
02:38
TRACK 005
02:38
TRACK 007
02:38
TRACK 009
02:38
TRACK 004
02:38
TRACK 002
02:38
TRACK 006
02:38
TRACK 008
02:38
TRACK 010
02:38
CD a Change Device
2.
Press the ▲▼◄► buttons to move to a
desired track, and then press the YELLOW
(C) button. A check appears on the track.
Repeat this procedure to select additional
tracks.
3. To remove a track from the list, move to
the track, and then press the YELLOW (C)
button again.
The check on the track is cancelled.
4. When done, press the
v
button.
The tracks you selected are displayed on
the right side of the screen. The player
plays the first track.
5. To change the play list, press the
@
button or RETURN button to return to the
Music List. Repeat Steps 2, 3, and 4.
6. To cancel the play list and return to the
Home screen, press the RETURN or EXIT
button.
NOTES
`
You can create a playlist with up to 99 tracks
on Audio CDs (CD-DA).
`
If you remove all the tracks from a play list and
then press the
v
button, the player lists and
plays all the tracks on the disc.
Ripping
Lets you copy audio files contents from data
Disc to USB/HDD device.
1. Open the disc tray. Place the audio (CDDA)
disc on the tray, and close the tray. Insert
a USB device into the USB jack on the
front of the product.
2. In Stop mode,
press the ▲▼◄► buttons
to move to a desired track, and then press
the YELLOW (C) button. A check appears
on the track.
Repeat this procedure to select additional
tracks.
3. To remove a track from the list, move to
the track, and then press the YELLOW (C)
button again.
The check on the track is cancelled.
4. When done, press the TOOLS button and
then select the Rip using the ▲▼ buttons.
and then press the
v
button. The Rip
pop-up appears.
5. Use the ▲▼ buttons to select the device
to store the ripped files, and then press
the
v
button.
NOTES
`
Do not disconnect the device while ripping is in
progress.
6. If you want to cancel ripping, press the
v
button and then select Yes. Select
No to continue ripping.
7. When ripping is complete, the "Ripping
completed." message appears. Press the
v
button to go back to the Playback
screen.
NOTES
`
This function may not be supported by some
discs.
`
On the Ripping screen, you can also choose
Select All and Deselect All.
-
Use Select All to select all tracks. This
cancels your individual track selections.
-
Use Deselect All to deselect all selected
tracks at once.
Disc Copy to USB
Lets you copy video/photo/music contents
from data Disc to USB/HDD device.
1. Open the disc tray. Place the data disc
on the tray, and close the tray. Insert a
USB device into the USB jack on the front
of the product. The new device pop-up
appears.
2. Press the
button, and then press the
buttons to select Blu-ray, DVD or CD.
3. Use the ▲▼ buttons to select Photos,
Videos or Music, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Photos, Videos &
Music screen and repeating Step 3.
4. With the Playback screen displayed, use
the ▲▼◄► buttons to select the Videos,
Photos, or Music, and then press the
YELLOW (C) button. A check appears to
the left of the desired item.
5. Repeat Step 4 to select and check
additional desired item.
6. To remove the desired item from the list,
press the YELLOW (C) button again.
The check on the desired item is removed.
7. When done, press the TOOLS button
and then select the Copy to USB using
the ▲▼ buttons. and then press the
v
button. The Copy to USB pop-up
appears.
8. Use the ▲▼ buttons to select the device
to store the copied files, and then press
the
v
button.
NOTES
`
Do not disconnect the device while copying is
in progress.
9. If you want to cancel copying, press the
v
button and then select Yes. Select
No to continue copying.
18
Appendix
Troubleshooting
Before requesting service, please try the following solutions.
PROBLEM SOLUTION
No operation can be
performed with the remote
control.
• Check the batteries in the remote control. They may need replacing.
• Operate the remote control at a distance of no more than 6.1m from the
player.
• Remove batteries and hold down one or more buttons for several minutes
to drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
Disc does not play. • Ensure that the disc is installed with the label side facing up.
• Check the region number of the Blu-ray Disc/DVD.
Disc Menu does not appear. • Ensure that the disc has disc menus.
The prohibition message
appears on the screen.
• This message appears when an invalid button is pressed.
• The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles).
•
You’ve requested a title or chapter number or search time that is out of range.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work properly if
the disc is not encoded with the corresponding function.
The screen ratio cannot be
changed.
• The Screen Ratio is fixed on your Blu-ray Disc/DVD.
• This is not a problem with the player.
No audio. • Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blank. • If the HDMI output is set to a resolution your TV cannot support (for example,
1080p), you may not see a picture on your TV.
• Press the
@
button (on top panel) for more than 5 seconds with no disc
inside. All settings will revert to the factory settings.
• When the factory default settings are restored, all stored user BD data is
deleted.
10. When copying is complete, the "Copying
completed." message appears. Press the
v
button to go back to the Playback
screen.
NOTES
`
This function may not be supported by some
discs.
`
On the Copying screen, you can also choose
Select All and Deselect All.
-
Use Select All to select all item. This
cancels your individual item selections.
-
Use Deselect All to deselect all selected
item at once.
Playing Photo Contents
You can control the playback of photo content
located on a Blu-ray disc, DVD, CD, USB
device, or your computer.
Using the Tools Menu
During playback, press the TOOLS button.
Start Slide Show/
Stop Slide Show
Select to start or stop the slide
show.
Slide Show Speed
Select to set a slide show's speed.
Background
Music
Select to listen to music while
viewing a slide show.
Zoom
Select to enlarge the current
picture. (Enlarge up to 4 times)
Rotate
Select to rotate the picture. (This
will rotate the picture either
clockwise or counter clockwise.)
Information
Shows the picture information.
NOTES
`
Depending on the disc or storage device, the
Tools menu may differ.
`
To enable the background music function, the
photo file must be in the same storage media
as the music file.
However, the sound quality can be affected
by the bit rate of the MP3 file, the size of the
photo, and the encoding method.
`
You can't enlarge the subtitle and PG graphic
in the full screen mode.
19
PROBLEM SOLUTION
Forgot password • Press the
@
button (on top panel) for more than 5 seconds with no disc
inside. All settings including the password will revert to the factory settings.
Don’t use this unless absolutely necessary.
• When the factory default settings are restored, all stored user BD data is
deleted.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
No HDMI output. • Check the connection between the TV and the HDMI jack of the player.
• Check if your TV supports 576p/480p, 720p, 1080i, or 1080p HDMI input
resolutions.
Abnormal HDMI output
screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
If you experience other
problems.
• Go to the contents and find the section of the user manual that contains the
explanations regarding the current problem, and follow the procedure once
again.
• If the problem still cannot be solved, please contact your nearest Samsung
authorised service centre.
DLNA function
I can see folders shared
through DLNA, but I cannot
see the files.
• DLNA shows only files corresponding to the Image, Music, and Movie
categories. Files that do not correspond to these categories are not
displayed.
Video is played intermittently. • Check if the network is stable.
• Check if the network cable is properly connected and if the network is
overloaded.
DLNA connection between
Player and PC is unstable.
• The IP address under the same subnetwork should be unique. If they are
not, IP interference can cause this phenomenon.
• Check if you have a firewall enabled.
If so, disable the firewall function.
PROBLEM SOLUTION
BD-LIVE
I cannot connect to the BD-
LIVE server.
• Check whether the network connection is working or not by using the
Network Status menu.
• Check whether the USB memory device is connected to the player.
• The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management.
• Check whether the BD-LIVE Internet Connection menu is set to Allow(All).
• If all above fails, contact the contents provider or update the player to the
latest firmware.
When using the BD-LIVE
service, an error occurs.
• The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management.
NOTES
`
When the factory default settings are restored, all stored user BD data is deleted.
Repairs
If you contact us to repair your player, an administration fee may be charged if either:
1. An engineer is called out to your home at your request and there is no defect in the
product.
2. You bring the unit to a repair centre and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or
begin any work on your player.
We recommend you read this manually thoroughly, search for a solution on line at www.
samsung.com, or contact Samsung Customer Care before seeking to repair your player.
20
1 / 1

Samsung BD-H5500 ユーザーマニュアル

カテゴリー
ブルーレイプレーヤー
タイプ
ユーザーマニュアル

他の言語で