Tektronix MSO58LP Installation And Safety Manual

5 Series MSO Low Profile

MSO58LP

Installation and Safety Manual

*P071356800*

071-3568-00

5 シリーズ MSO ロー・プロファイル

MSO58LP 型

設置と安全性に関するマニュアル

5 系列紧凑型 MSO

MSO58LP

安装和安全手册

5 Series MSO Low Profile

MSO58LP

Installation and Safety Manual

www.tek.com

071-3568-00

Supports Product Firmware V1.4 and above.

Copyright

©

protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued

and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges

reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TekSecure is a trademark of Tektronix, Inc.

FlexChannel, TekVPI, FastAcq, and e*Scope are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

■

In North America, call 1-800-833-9200.

■

Worldwide, visit www.tek.com to find contacts in your area.

Warranty

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years from the date of

shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product

without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement

products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and

products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and

make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective

product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to

Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible

for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care.

Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than

Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to

incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product

that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty

of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS

OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND

EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL

NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER

TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

[W4 – 15AUG04]

Table of Contents

Important safety information ................................................................................................................................ iii

General safety summary ................................................................................................................................ iii

Service safety summary ................................................................................................................................. v

Terms in the manual ...................................................................................................................................... vi

Terms on the product .................................................................................................................................... vi

Symbols on the product ................................................................................................................................. vi

Preface ............................................................................................................................................................... vii

Key features .................................................................................................................................................. vii

Related documents ....................................................................................................................................... vii

Installing your instrument

Check shipped accessories ........................................................................................................................... 1

Operating requirements ................................................................................................................................. 1

Input signal requirements ............................................................................................................................... 2

Installing the instrument in a rack ................................................................................................................... 2

Secure (lock) the oscilloscope ....................................................................................................................... 3

Powering the oscilloscope .............................................................................................................................. 4

Check that oscilloscope passes power-on self tests ...................................................................................... 4

Connecting Probes ......................................................................................................................................... 5

Getting acquainted with your instrument

MSO58LP front panel connections ............................................................................................................... 7

Rear panel connections ................................................................................................................................. 9

The graphical user interface ........................................................................................................................... 9

Configure the instrument

Set the time zone and clock readout format ................................................................................................. 11

Download and install the latest firmware ...................................................................................................... 11

Run Signal Path Compensation (SPC) ........................................................................................................ 12

Compensate the TPP0500B or TPP1000 probes ........................................................................................ 13

Connect to a network (LAN) ......................................................................................................................... 14

Remote access from a Web browser ........................................................................................................... 15

Operating basics

MSO58LP Installation and Safety Manual

i

Cleaning the instrument

Cleaning ....................................................................................................................................................... 19

EMC, safety and environmental compliance

Compliance Information ............................................................................................................................... 21

EMC compliance .................................................................................................................................... 21

Safety compliance .................................................................................................................................. 22

Environmental compliance ..................................................................................................................... 23

Table of Contents

ii MSO58LP Installation and Safety Manual

Important safety information

This manual contains information and warnings that must be followed by the user for safe operation and to keep the product in a

safe condition.

To safely perform service on this product, see the Service safety summary that follows the General safety summary.

General safety summary

Use the product only as specified. Review the following safety precautions to avoid injury and prevent damage to this product or

any products connected to it. Carefully read all instructions. Retain these instructions for future reference.

This product shall be used in accordance with local and national codes.

For correct and safe operation of the product, it is essential that you follow generally accepted safety procedures in addition to

the safety precautions specified in this manual.

The product is designed to be used by trained personnel only.

Only qualified personnel who are aware of the hazards involved should remove the cover for repair, maintenance, or adjustment.

Before use, always check the product with a known source to be sure it is operating correctly.

This product is not intended for detection of hazardous voltages.

Use personal protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.

While using this product, you may need to access other parts of a larger system. Read the safety sections of the other

component manuals for warnings and cautions related to operating the system.

When incorporating this equipment into a system, the safety of that system is the responsibility of the assembler of the system.

To avoid fire or personal injury

Use proper power cord. Use only the power cord specified for this product and certified for the country of use. Do not use the

provided power cord for other products.

Ground the product. This product is grounded through the grounding conductor of the power cord. To avoid electric shock, the

grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the

product, ensure that the product is properly grounded. Do not disable the power cord grounding connection.

Power disconnect. The power cord disconnects the product from the power source. See instructions for the location. Do not

position the equipment so that it is difficult to operate the power cord; it must remain accessible to the user at all times to allow for

quick disconnection if needed.

Connect and disconnect properly. Do not connect or disconnect probes or test leads while they are connected to a voltage

source. Use only insulated voltage probes, test leads, and adapters supplied with the product, or indicated by Tektronix to be

suitable for the product.

Observe all terminal ratings. To avoid fire or shock hazard, observe all rating and markings on the product. Consult the product

manual for further ratings information before making connections to the product. Do not exceed the Measurement Category

(CAT) rating and voltage or current rating of the lowest rated individual component of a product, probe, or accessory. Use caution

when using 1:1 test leads because the probe tip voltage is directly transmitted to the product.

Observe all terminal ratings. To avoid fire or shock hazard, observe all rating and markings on the product. Consult the product

manual for further ratings information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.

Do not float the common terminal above the rated voltage for that terminal.

MSO58LP Installation and Safety Manual

iii

The measurement terminals on this product are not rated for connection to mains or Category II, III, or IV circuits.

Do not operate without covers. Do not operate this product with covers or panels removed, or with the case open. Hazardous

voltage exposure is possible.

Avoid exposed circuitry. Do not touch exposed connections and components when power is present.

Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by qualified

service personnel.

Disable the product if it is damaged. Do not use the product if it is damaged or operates incorrectly. If in doubt about safety of the

product, turn it off and disconnect the power cord. Clearly mark the product to prevent its further operation.

Before use, inspect voltage probes, test leads, and accessories for mechanical damage and replace when damaged. Do not use

probes or test leads if they are damaged, if there is exposed metal, or if a wear indicator shows.

Examine the exterior of the product before you use it. Look for cracks or missing pieces.

Use only specified replacement parts.

Wear eye protection. Wear eye protection if exposure to high-intensity rays or laser radiation exists.

Do not operate in wet/damp conditions. Be aware that condensation may occur if a unit is moved from a cold to a warm

environment.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry. Remove the input signals before you clean the product.

Provide proper ventilation. Refer to the installation instructions in the manual for details on installing the product so it has

proper ventilation.

Slots and openings are provided for ventilation and should never be covered or otherwise obstructed. Do not push objects into

any of the openings.

Provide a safe working environment. Always place the product in a location convenient for viewing the display and indicators.

Avoid improper or prolonged use of keyboards, pointers, and button pads. Improper or prolonged keyboard or pointer use may

result in serious injury.

Be sure your work area meets applicable ergonomic standards. Consult with an ergonomics professional to avoid stress injuries.

Use care when lifting and carrying the product. This product is provided with a handle or handles for lifting and carrying.

WARNING. The product is heavy. To reduce the risk of personal injury or damage to the device get help when lifting or carrying

the product.

Use only the Tektronix rackmount hardware specified for this product.

Important safety information

iv MSO58LP Installation and Safety Manual

Probes and test leads

Before connecting probes or test leads, connect the power cord from the power connector to a properly grounded power outlet.

Keep fingers behind the protective barrier, protective finger guard, or tactile indicator on the probes.

Remove all probes, test leads and accessories that are not in use.

Use only correct Measurement Category (CAT), voltage, temperature, altitude, and amperage rated probes, test leads, and

adapters for any measurement.

Beware of high voltages. Understand the voltage ratings for the probe you are using and do not exceed those ratings. Two

ratings are important to know and understand:

■

The maximum measurement voltage from the probe tip to the probe reference lead

■

The maximum floating voltage from the probe reference lead to earth ground

These two voltage ratings depend on the probe and your application. Refer to the Specifications section of the manual for more

information.

WARNING. To prevent electrical shock, do not exceed the maximum measurement or maximum floating voltage for the

oscilloscope input BNC connector, probe tip, or probe reference lead.

Connect and disconnect properly. Connect the probe output to the measurement product before connecting the probe to the

circuit under test. Connect the probe reference lead to the circuit under test before connecting the probe input. Disconnect the

probe input and the probe reference lead from the circuit under test before disconnecting the probe from the measurement

product.

Connect the probe reference lead to earth ground only.

Inspect the probe and accessories. Before each use, inspect probe and accessories for damage (cuts, tears, or defects in the

probe body, accessories, or cable jacket). Do not use if damaged.

Ground-referenced oscilloscope use. Do not float the reference lead of this probe when using with ground-referenced

oscilloscopes. The reference lead must be connected to earth potential (0 V).

Floating measurement use. Do not float the reference lead of this probe above the rated float voltage.

Service safety summary

The Service safety summary section contains additional information required to safely perform service on the product. Only

qualified personnel should perform service procedures. Read this Service safety summary and the General safety summary

before performing any service procedures.

To avoid electric shock. Do not touch exposed connections.

Do not service alone. Do not perform internal service or adjustments of this product unless another person capable of rendering

first aid and resuscitation is present.

Disconnect power. To avoid electric shock, switch off the product power and disconnect the power cord from the mains power

before removing any covers or panels, or opening the case for servicing.

Use care when servicing with power on. Dangerous voltages or currents may exist in this product. Disconnect power, remove

battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.

Verify safety after repair. Always recheck ground continuity and mains dielectric strength after performing a repair.

Important safety information

MSO58LP Installation and Safety Manual v

Terms in the manual

These terms may appear in this manual:

WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

Terms on the product

These terms may appear on the product:

■

DANGER indicates an injury hazard immediately accessible as you read the marking.

■

WARNING indicates an injury hazard not immediately accessible as you read the marking.

■

CAUTION indicates a hazard to property including the product.

Symbols on the product

When this symbol is marked on the product, be sure to consult the manual to find out the nature of the potential

hazards and any actions which have to be taken to avoid them. (This symbol may also be used to refer the user to

ratings in the manual.)

The following symbols may appear on the product:

Important safety information

vi MSO58LP Installation and Safety Manual

Preface

This manual provides product safety and compliance, how to connect and power on the oscilloscope, and an introduction to the

instrument features, controls and basic operations. See the product Help file for more detailed information.

Key features

Welcome to the 5 Series MSO Low Profile. The 5 Series MSO Low Profile (MSO58LP) is an 8-channel oscilloscope with the

world's first FlexChannel

®

-based inputs, enabling you to efficiently and cost-effectively perform mixed signal debugging on

virtually any design.

■

1 GHz Bandwidth

■

8-channel model with FlexChannel inputs

■

Each FlexChannel

®

input supports one analog channel or eight digital channels, in any combination

■

FlexChannel

®

inputs are compatible with TekVPI

®

probes

■

User interface designed to optimize touch screen use and quickly access key settings

■

Stacked mode places each channel or waveform in its own horizontal 'slice' on the screen, allowing for cleaner signal

viewing and measuring

■

Maximum 6.25 GS/s sample rate

■

125 M points record length on all channels

■

500,000 waveforms/second maximum waveform capture rate

■

No set limit on the number of math, reference, and bus waveforms you can display

1

■

Integrated optional features include a 50 MHz arbitrary function generator (AFG), and a DVM and trigger frequency counter

■

Optional advanced triggering features let you trigger and take measurements on industry serial bus data standards including

I

2

C, SPI, USB 2.0, CAN, CAN FD, LIN, FlexRay, RS-232/422/485/UART, MIL-STD-1553, ARINC 429, Audio (I

2

S, LJ, RJ,

TDM), and Ethernet

Related documents

Use the related documents to access information on how to remotely program or operate the instrument, understand theory of

operation, replace suspected modules, and do other tasks.

To learn about Use this document

How to use instrument

functions

5 Series MSO MSO54, MSO56, MSO58, MSO58LP Help (Tektronix part number 077-1303-xx;

Printable version of the instrument Help; available at www.tektronix.com/downloads)

5 Series MSO MSO58LP Installation and Safety Manual (Tektronix part number 071-3568-xx);

standard accessory with the instrument. Single document with English, Japanese, and

Simplified Chinese languages. A Russian language version is available to download from the

Tektronix web site (Tektronix part number 077-1404-xx)

How to remotely control the

instrument

5 Series MSO MSO54, MSO56, MSO58, MSO58LP Programmer Manual (Tektronix part

number 077-1305-xx; available at www.tek.com/downloads)

1

The actual number of waveforms depends on available system memory.

MSO58LP Installation and Safety Manual vii

To learn about Use this document

Instrument specifications and

procedures to verify the

instrument meets

specifications

5 Series MSO MSO54, MSO56, MSO58, MSO58LP Specifications and Performance

Verification Technical Reference (Tektronix part number 077-1306-xx; available at

www.tek.com/downloads)

Instrument theory of operation,

troubleshooting, disassembly,

and replaceable parts

5 Series MSO MSO58LP Service Manual (Tektronix part number 077-1405-xx; available at

www.tek.com/downloads)

Using the TLP058 Logic Probe TLP058 FlexChannel

®

Logic Probe Instructions (Tektronix part number 071-3515-xx; available

at www.tek.com/downloads)

Converting the instrument for

benchtop use

MSO58LP Bench Conversion Kit Instructions (Tektronix part number 075-1102-xx; available at

www.tek.com/downloads)

Preface

viii MSO58LP Installation and Safety Manual

Installing your instrument

Check shipped accessories

Make sure that you received everything you ordered. If anything is missing, contact Tektronix Customer Support. In North

America, call 1-800-833-9200. Worldwide, visit www.tek.com to find contacts in your area.

Check the packing list that came with your instrument to verify that you have received all standard accessories and ordered

items. If you purchased factory installed options such as a Serial Bus and Triggering option, or the 5-PWR power measurements

option, tap Help > About to confirm that the option(s) are listed in the Installed Options table.

MSO58LP standard accessories

Item Quantity Tektronix part number

5 Series MSO MSO58LP Installation and Safety Manual 1 071-3568-xx

Power cord 1 Depends on region

Calibration certificate 1 N/A

Report of factory installed licenses 1 N/A

Operating requirements

Use the oscilloscope within the required operating temperature, power, altitude, and signal input voltage ranges to provide the

most accurate measurements and safe instrument operation.

Environment requirements

Characteristic Description

Operating temperature 0 °C to +50 °C (+32 °F to +122 °F)

For proper cooling, keep the sides of the instrument clear of obstructions for 2 inches

(51 mm).

Operating humidity 5% to 90% relative humidity (% RH) up to +40 °C (+104 °F)

5% to 55% RH above +40 °C up to +50 °C (+104 °F to +122 °F), Noncondensing.

Operating altitude Up to 3000 meters (9842 feet)

Power requirements

Characteristic Description

Power source voltage 100 V - 240 V

AC RMS

, ±10%, single phase

Power source frequency 50/60 Hz, 100-240 V (90-264 V)

400 Hz, 115 V (103-127 V)

Power consumption All models: 400 W maximum

MSO58LP Installation and Safety Manual 1

Input signal requirements

Keep the input signals within allowed limits to ensure the most accurate measurements and prevent damage to the analog and

digital probes or instrument.

Make sure that input signals are within the following requirements.

Input Description

Analog input channels, 1 M Ω setting, maximum input voltage

at BNC

300 V

RMS

Measurement Category II

Analog input channels, 50 Ω setting, maximum input voltage at

BNC

5 V

RMS

Digital input channels, maximum input voltage range at digital

inputs

Observe probe ratings

TLP058; ±42 V

P

Ref In maximum input voltage at BNC (rear panel) 7 V

PP

AUX trigger input ±5 V

RMS

Installing the instrument in a rack

Use these instructions to install the MSO58LP into a standard 19" equipment rack.

The MSO58LP comes equipped with the rack bracket hardware installed on the chassis. You will need to install the rear rack

brackets in the rack. The instrument ships with a bag of assorted bolts and washers for installing the instrument in the most

common rack types.

To use an MSO58LP on a bench, purchase and install the MSO58LP Benchtop Conversion kit (Tektronix part number 020-3180-

xx). The kit includes chassis feet and a handle, and lets you stack instruments on a bench.

Follow these steps to install the instrument in a rack:

WARNING. To prevent injury, two people are required to install the instrument.

1. Use two bolts and washers from the supplied hardware to attach one of the rear rack brackets to the rear of the rack.

Tighten by hand.

2. Using two people to support the instrument, insert the instrument from the front of the rack so that the chassis rack bracket

inserts into the rear rack bracket.

3. Continue pushing from the front until the instrument is flush with the front of the rack.

Installing your instrument

2 MSO58LP Installation and Safety Manual

4. Use four bolts and washers from the supplied hardware to attach the front of the instrument to the rack. Tighten by hand to

support the instrument.

5. From the rear of the rack, slide the second rear rack bracket onto the instrument chassis rack bracket until the rear rack

bracket is flush with the rear rack.

6. Use two bolts and washers from the supplied hardware to attach the second rear rack bracket to the rear of the rack.

Tighten by hand.

7. Tighten all bolts to 1.1 N·m.

8. Using a 5/16 inch wrench, attach two supplied hexhead bolts to the rack bracket assembly on each side, to lock the

brackets in place and prevent the instrument from unintentional removal when the front rack screws are removed (see the

following image). There are four bolt positions available on each side (see image). Tighten the bracket lock bolts to 0.7 N·m.

9. Attach power cord and cables to rear chassis as needed.

End of rack mount instructions.

Secure (lock) the oscilloscope

Lock an oscilloscope to a test bench or equipment rack to prevent property loss.

Attach a standard laptop security lock to the rear panel of the oscilloscope, to secure the oscilloscope to a workbench, rack, or

other location.

Installing your instrument

MSO58LP Installation and Safety Manual 3

Powering the oscilloscope

Use this procedure to connect the oscilloscope to line power and power on and off the oscilloscope. Always connect the

oscilloscope to AC power using the power cord that shipped with the instrument.

Prerequisite: Use the AC power cord that shipped with your oscilloscope.

1. Connect the supplied power cord to the oscilloscope power connector.

Figure 1: MSO58LP power cord connector and power standby switch

2. Connect the power cord to an appropriate AC mains source.

Power is supplied to the power supply and some other boards whenever the AC power cord is connected to a live mains

circuit, putting the instrument in standby mode.

3. Push the front panel power button to power the instrument on and off.

The power button color indicates instrument power states:

No light – no AC power applied

Yellow – standby mode

Blue – powered on

4. To completely remove power from the instrument, disconnect the power cord.

Check that oscilloscope passes power-on self tests

Power-on self tests verify that all oscilloscope modules are working correctly after power up.

Prerequisite: Connect a monitor to a video output on the rear panel, and connect a mouse to a USB port.

1. Power on the oscilloscope and wait until the oscilloscope screen appears.

2. Select Utility > Self Test from the top-edge Menu bar to open the Self Test configuration menu.

3. Check that the status of all power-on self tests are Passed.

If one or more power-on self tests shows Failed:

a. Power cycle the oscilloscope.

b. Tap Utility > Self Test. If one or more power-on self tests still shows Failed, contact Tektronix Customer Support.

Installing your instrument

4 MSO58LP Installation and Safety Manual

Connecting Probes

Probes and cables connect the oscilloscope to your device under test (DUT). Use a probe that best matches your signal

measurement needs.

Figure 2: Connecting probes to the MSO58LP

Connect TPP0500, TPP1000, TekVPI+

®

, TekVPI

®

, or other supported Tektronix analog probes by pushing them into a

FlexChannel

®

connector. The probe base latch locks with a 'click' when the probe is fully seated.

TekVPI probes automatically set the channel input parameters for that probe (bandwidth, attenuation, termination, and so on). If

a probe has a Menu button, push that button to open an on-screen configuration menu. Follow instructions provided with active

probes to set their parameters (auto zero, degauss, and so on).

To connect a TLP058 FlexChannel

®

Logic Probe:

1. Move the locking lever to the unlocked position, then let go to reset locking lever to the center position.

2. Insert the probe into a FlexChannel

®

connector until fully seated and the lock mechanism clicks.

3. Move the locking lever to the locked position. The status light should be a solid green.

4. To disconnect the TLP058 probe, move and hold the locking lever at the unlocked position and pull out the probe. Do not

pull on the ribbon cable while removing the probe.

Connect a BNC probe or cable by pushing it onto a channel BNC bayonet connector and turn the lock mechanism clockwise until

it locks.

NOTE. Connecting a probe does not automatically enable that channel.

Installing your instrument

MSO58LP Installation and Safety Manual 5

Installing your instrument

6 MSO58LP Installation and Safety Manual

ページが読み込まれています...

Tektronix MSO58LP Installation And Safety Manual

このマニュアルも適しています

Tektronix MSO58LP Installation And Safety Manual

他の言語で

関連論文

その他のドキュメント