Z-EDGE Z-EDGE Z3D Dash Cam Dual Cameras on a Budget ユーザーガイド

BEDIENUNGSANLEITUNG

USER GUIDE

Z3D

English 1

Deutsch 22

CONTENTS / INHALTSVERZEICHNIS /

Table of Contents

1 Introduction .................................................................................................................................... 2

1.1 Features ................................................................................................................................. 2

1.2 What's in the Box .............................................................................................................. 2

1.3 Product Overview ............................................................................................................. 3

2 Getting Started .............................................................................................................................. 4

2.1 Inserting the Memory Card ......................................................................................... 4

2.2 Installation ............................................................................................................................ 5

2.3 Adjust Device Position ................................................................................................... 6

2.4 Connecting to Power ...................................................................................................... 7

2.5 Set Date & Time ................................................................................................................ 8

2.6 Default Settings ................................................................................................................. 8

2.7 Factory Reset ....................................................................................................................... 8

2.8 Rear Camera Installation ............................................................................................... 9

3 Using the Car Dash Cam ........................................................................................................ 10

3.1 Recording Videos ........................................................................................................... 10

3.2 Recording Screen ........................................................................................................... 10

3.3 Adjusting the Settings .................................................................................................. 11

3.4 Loop Recording ............................................................................................................... 11

3.5 Emergency Video Protection .................................................................................... 11

3.6 Motion Detection ........................................................................................................... 12

3.7 Vibration Detection ....................................................................................................... 12

3.8 Parking Monitoring ....................................................................................................... 12

3.9 Taking a Snapshot ......................................................................................................... 12

3.10 Playback Videos & Photos ...................................................................................... 12

3.11 Managing Video & Photo Files ............................................................................ 13

3.12 GPS ...................................................................................................................................... 13

4 Menu Overview .......................................................................................................................... 15

5 FAQs ................................................................................................................................................. 17

6 Customer Support .................................................................................................................... 18

7 Warranty ........................................................................................................................................ 18

8 Product Specifications .............................................................................................................19

-1-

-2-

1 Introduction

Welcome to buy the Z3D car dash cam. Protect you and your vehicle with

real-time video and audio recording whilst you're driving. Featuring a stealth

size design and dual-lens for recording front and back. Please read this manual

carefully before using this product. We hope you enjoy using this product.

1.1 Features

• 2560x1440P resolutions

• 2.7" LCD Color screen

• Up to 150-degree wide angle lens

• Built-in G-Sensor

• Motion Detection

• Parking Mode

• Audio Recording

• GPS

1.2 What's in the Box

Car Dash Cam

Car Charger with

USB Cable

Car Mount with

Built-in GPS

User Guide

Rear Camera with 26-foot

USB Cable

Warranty CardUSB Cable

-3-

1.3 Product Overview

1

2

3

4

5

6

7

8

9

Power Button

TF/MicroSD Card Slot

ESC/Menu Button

Up Button

Down Button

OK/Record Button

Micro USB Port

Suction Mount Slot

Mini USB Port

10

11

12

13

14

15

16

17

Speaker

Front-View Lens

Mic

USB cable

Suction Cup Mount

USB connector

Mini USB Port

Rear-View Lens

1

3

4

5

6

2

7 8 9

12

10 11

13 14 15

16

17

-4-

2 Getting Started

2.1 Inserting the Memory Card

Insert the memory card, with the pins facing

towards the back of the device, until it clicks

into place.

Remove Memory Card

Push the edge of the memory card inward until you feel it click, then allow it to

push out until you can remove it from the slot.

WARNING:

It is recommended to format the memory card in the dash cam directly in

Menu>General Setting>Format SD card before initial use. Please note

that all data saved on the memory card will be erased after formatting.

Note:

• Supports Micro SDXC cards up to 256GB.

• Do not remove or insert memory card whilst the device is powered on -

this may damage the memory card.

Storage Capacity Video Recording Time

For reference only

16GB

32GB

64GB

128GB

256GB

1.5 Hours

3 Hours

6 Hours

12 Hours

24 Hours

-5-

1 2

2.2 Installation

Please follow the below instructions for mounting your dash cam to your

vehicles windshield:

1. Slide the car mount into the slot on top of the device until a click sound is

heard.

2. Press the suction-cup firmly against your windshield, and rotate the lever

clockwise (12 o'clock) to secure.

WARNING:

Do not install the device on a tinted window - doing so may damage the tint

film.

1 2

2.3 Adjust Device Position

1. Loosen the nut to swivel the device vertically. Click into place and secure by

tightening the nut.

2. Swivel the device horizontally for a clear view.

-6-

-7-

2.4 Powering the Dash Cam

Use only the supplied car charger to power the dash cam and charge the

built-in battery.

1. Plug the USB cable (13) on the

car mount into the car

dash cam's USB connector (7).

2. Plug one end of the USB

charging cable into the USB

Connector on the car mount (15).

3. Plug the other end into the car

charger, and insert that into

your vehicles lighter socket.

Automatic Power

• Once the vehicle's engine is switched on, the dash cam will automatically

power on.

• When the vehicle engine is switched off, the dash cam will automatically

save the recording and power off within 10 seconds.

Manual Power

• To manually turn the power on, press and hold

the 'Power' Button (1) for up to 3 seconds.

• To manually turn the power off, press and hold

the 'Power' Button (1) for 3 seconds.

WARNING:

If the environment reaches 115-degrees Fahrenheit or above, the car charger

may stop charging the dash cam battery. This is characteristic of a Lithium

Polymer battery and is not a malfunction.

-8-

2.5 Set Date & Time

Before using the device, we recommend you set the correct date and time:

1. If the device is recording, short press the 'OK/REC' button (6) to stop and

enter Standby Mode.

2. Press the 'Esc/Menu' button (3) to enter the General Settings menu.

3. Press the 'Up' and 'Down' buttons (4 & 5) to select Date/Time and press

'OK/REC' button (6) to confirm.

4. Press the 'Up' and 'Down' buttons (4 & 5) to adjust the value and then press

'OK/REC' button (6) to confirm and move to the next field.

5. With all fields correct, press the 'OK/REC' button (6) to save and exit the menu.

WARNING:

Date/Time settings may automatically reset themselves if the battery is

allowed to completely drain. To ensure the correct time you must set the

time to your local time zone.

2.6 Default Settings

2.7 Factory Reset

To reset the dash cam to factory default settings long press the 'Power'

button (1) for 7 seconds.

Default Settings

Resolution 1080P 30,1080P 30

Loop Recording 3 mins

Motion Detect OFF

Voice Setup ON

Date Stamp ON

G-Sensor sensitivity Normal

Button Beep ON

Language English

Frequency 60 Hz

LCD auto Off 3 Minutes

Auto Power Off OFF

Parking monitoring OFF

-9-

2.8 Rear Camera Installation

1. Connect one end of the Mini USB cable into the Mini USB Port (9) on the

dash camera. Connect the other end into the Mini USB Port (16) on the rear

camera.

2. Turn the camera on. The rear-lens view will automatically appear on the

display screen in Dual (PiP) format.

Tip: To view full-screen, press the 'Esc/Menu' button (3) to enter the General

Settings menu. Use the 'Up' and 'Down' buttons (4 & 5) to select the Screen

Display option and press the 'OK/REC' button (6) to confirm. Then select

Rear Camera using 'Up' and 'Down' buttons (4 & 5) and confirm with the

'OK/REC' button (6).

3. Whilst looking at the display screen and without removing the adhesive

backing, find a suitable location for installing your rear-lens camera on your

rear windshield.

4. Having found a suitable location on your rear windshield, peel off the

protective plastic backing from the adhesive mount. Press firmly against your

rear windshield to secure.

5. For a more organized car environment, the rear camera USB cable can be

routed as indicated by the dashed line in the diagram.

-10-

3 Using the Car Dash Cam

3.1 Recording Videos

With an SD card inserted and the device connected to power, when the car

engine is switched on the dash cam will automatically power on and start

recording. When the vehicle engine is switched off, the dash cam will

automatically save the recording and power off within 10 seconds.

Alternatively, short press the 'OK/REC' button (6) to stop/start video recording

manually.

3.2 Recording Screen

6

No. Item Description

Recording Flashing red light indicates device is recording with

time showing current duration of recording.

GPS Indicates if the GPS is connected.

Video Protection Indicates if video protection is active. Press

'Esc/Menu' button (3) to activate when recording.

Indicates if parking monitor is on/off.

Resolution Indicates current resolution settings.

Loop Recording Indicates loop recordings length 1, 2 or 3 minutes.

Motion Detection Indicates if motion detection on/off.

Parking Monitor

1

4

7

Audio recording Indicates if audio recording active, press 'Down'

button (5) to turn on/off when recording.

9

2

3

5

1 2 3 4 5 6

14

8

7

9

10

11

12

13

8Press 'Up' button (4) to enter camera mode.

Camera button

-11-

3.3 Adjusting the Settings

Customize the video recording and other general settings via the on-screen

display (OSD) menus:

If the device is recording, short press the 'OK/REC' button (6) to stop and enter

Standby Mode.

1. Press the 'Esc/Menu' button (3) to enter the General Settings menu.

2. Press the 'Up' and 'Down' buttons (4 & 5) to select a menu option and press

the 'OK/REC' button (6) to enter the selected menu.

3. Press the 'Up' and 'Down' buttons (4 & 5) to select the desired setting and

press the 'OK/REC' button (6) to confirm the setting.

4. From the General Settings menu Press the 'Esc/Menu' button (3) to enter the

Feature Settings menu.

5. Press the 'Up' and 'Down' buttons (4 & 5) to select the desired setting and

press the 'OK/REC' button (6) to confirm the setting.

3.4 Loop Recording

Videos are recorded and saved to the memory card in set intervals. Once the

memory card is full, Loop Recording automatically overwrites the earliest

unprotected saved file. This prevents long duration video clips from being lost

in a single overwrite.Video files can be saved to the memory card in 1, 2 or 3

mins intervals. General Settings > Loop Recording

3.5 Emergency Video Protection

If Vibration Detection is enabled and senses an unusual impact or collision the

dash cam will automatically protect the currently recorded video file from

being overwritten. A icon appears top left to signify the current recording is

protected.To manually protect a video file during a recording, short press the

'Esc/Menu' button (3).

No. Item Description

Record / Stop Indicates if device is recording, press 'OK/REC'

button (6) to start/stop recording.

Time Stamp Time and date

Menu Press 'Esc/Menu' button (3) to enter menu.

Preview Press 'Down' button (5) to preview video/photo.

10/

13

14

11

12

-12-

3.6 Motion Detection

With Motion Detection enabled, video recording is automatically started when

movement is detected by the camera lens. After approximately 10 seconds with

no movement detected, video recording is automatically paused.

Enable/disable feature: Feature Settings > Motion Detect

3.7 Vibration Detection

The Vibration Detection feature senses for unusual impacts or collisions

detected by the built-in G-Sensor. It automatically triggers the Emergency

Video Protection and Parking Mode features.

Set the sensitivity to automatically trigger these features with smaller or larger

vibrations (feature can also be turned Off): Feature Settings > G-Sensor

Sensitivity

3.8 Parking Monitoring

Enable Parking Monitoring for the dash cam to continue monitoring your

vehicle for unusual impact or collision when the engine is turned off and parked.

If a vibration is detected, the device will automatically turn on and begin

recording. Approximately 20 seconds after the motion or vibration is finished,

the device will automatically return to monitoring mode. All recordings are

automatically protected from being overwritten.

Enable/disable feature: Feature Settings > Parking Monitoring

Please note: When protection space (30% TF card capacity is full,The protected

files will be overwritten with newly recorded protected files

3.9 Taking a Snapshot

1. If the device is recording, short press the 'OK/REC' button (6) to stop and

enter Standby Mode.

2. Short press the 'Up' button (4) to enter Photo Mode.

3. Press the 'Up' button (4) to take a snapshot.

3.10 Playback Videos & Photos

1. If the device is recording, short press the 'OK/REC' button (6) to stop and

enter Standby Mode.

2. Press the 'Down' button (5) to enter Playback Mode.

-13-

3. Press the 'Up' and 'Down' buttons (4 & 5) to select between Normal Video,

Emergency Video or Photo. Press the 'OK/REC' button (6) to select or press

the 'ESC/Menu' button (3) to return to standby mode.

4. Press the 'Up' and 'Down' buttons (4 & 5) to choose the file to preview and

'OK/REC' button (6) to select.

5. Press the 'OK/REC' button (6) to preview the file.

6. Press the 'ESC/Menu' button (3) to return to the playlist menu.

3.11 Managing Video & Photo Files

1.Go to the Playlist menu (see 3.10).

2. Navigate to the file you wish to manage and press the 'OK/REC' button (6) to

select.

3. Press the 'Up' button (4) to delete the file.

4. Press the 'Up' and 'Down' buttons (4 & 5) to select between Yes and No.

5. Use the 'OK/REC' button (6) to confirm choice.

WARNING:

Deleted files cannot be recovered. Please ensure you backup important files

before deleting them.

3.12 GPS

Integrated into the car mount suction cup is a GPS receiver which can pinpoint

the location of your car dash cam anywhere on Earth. Video recordings include

GPS tracking data which records location, speed, time and other variables that

can be viewed on a GPS Multimedia Player.

1. Ensure the car mount USB cable is plugged into the car dash cams' USB

connector to enable GPS tracking.

2. Go to http://zeroedgetechnology.com/downloads/ to download the

compatible GPS Multimedia Player.

3. Install GPS Multimedia Player on your laptop or computer.

4. Run the program and click 'Open File' to search and playback a video

recording.

-14-

Note:

• GPS Multimedia Player compatible with Microsoft Windows and Apple Mac.

• GPS tracking data may not be viewable using other GPS Players.

• Car dash cam videos can be played from the SD card or from the car

dash cam when connected to a computer via the USB port.

-15-

Menu Feature Description Available option

Set the resolution of the

videos to be recorded.

Resolution

Front camera and rear

camera connected:

1080P30, 1080P30

Front camera only:

2560x1440P 30 fps

2304x1296P 30 fps

1920x1080P 60 fps

1920x1080P 30 fps

1280x720P 120 fps

1280x720P 60 fps

1280x720P 30 fps

Set the duration of each

video file recorded to the

memory card (see 3.4).

Loop Recording 1 min / 2 mins / 3 mins

Set the dash cam

exposure

Exposure

+2.0, +5/3, +4/3, +1.0,

+2/3, +1/3, +0.0, -1/3.

-2/3, -1.0, -4/3, -5/3, -2.0

Sets the screen displayScreen Display Front Camera, Rear

Camera, PIP

Set the date/time (see 2.5).Time Setup YYYY / DD / MM / GMT

HH : MM : SS

General

Settings

Set dash cam languageLanguage

Enable/disable audio

recording.

Voice Setup On / Off

English, French, German,

Portuguese, Spanish,

Italian

Add/remove a date and

time stamp, Driver ID, and

Logo stamp visible on

saved video recordings.

Date Stamp On / Off,

Driver ID Setting On / Off,

Logo Stamp On / Off

Stamp Setup

Input Driver ID settingDriver ID Setting

Enable/Disable Key ToneButton Beep On / Off

4 Menu Overview

-16-

Menu Feature Description Available option

Change frequencyFrequency 50Hz / 60Hz

Format the micro SD cardFormat OK / Return

Displays firmware versionVersion Info

General

Settings

Feature

Settings

Enable/Disable Wide

Dynamic Range

WDR

Set the duration for Auto

Power Off

Auto Power Off 1 min / 3 mins /

5 mins / Off

Set the duration for LCD

Auto Off

LCD Auto Off 1 min / 3 mins / Off

On / Off

OK / Return

Restore the car dash cam

to default settings

Adjust the light G-Sensor

Sensitivity

Default

1 Hour, 2 Hours,

4 Hours, Off

Set the fatigue alarm

Driver fatigue

alarm

On / Off

Enable/Disable remind lightRemind lights

On / Off

Enable/Disable the motion

detection feature

Motion Detect

On/Off

Enable/Disable to protect

your vehicle from hit-and-

run incidents when the

engine is off (see 3.8).

Parking

Monitoring

Off / High / Normal /

Low

G-Sensor

Sensitivity

-17-

5 FAQs

Where should I place the dash cam?

• We recommend that you mount the car dash cam as close to the center of

the windshield as possible. This should neither distract the driver nor block

the drivers view (see 2.4).

Why does the dash cam stop recording after some time?

• If motion detection is enabled, the dash cam will automatically stop

recording when no movements is detected for more than 15 seconds (see 3.6).

• Your micro SD card may be full and need to be formatted before using again.

1080P HD videos are big in size and G-sensor locked videos cannot be erased

automatically. We recommend formatting your memory card every 14 days.

Why do you recommend Class 10 micro SD card or above?

• 1080P HD video has a bigger data flow and hence requires a micro SD card

with faster writing speed. If memory cards below Class 10 are used, they may

cause the dash cam to freeze or other related video recording/erasing

issues.

How do I turn off audio during recording?

• To turn off the Audio Recording, short press the 'Down' button (5) during

recording. (Please note: this does not interrupt the video recording).

How long will my battery last after a full charge?

• The dash cam battery usually takes 2-3 hours to fully charge. This can

happen simultaneously whilst the dash cam is plugged into your car and

recording. The battery can last 15 mins on a full charge depending on the

model and environmental temperature.

How do I record videos?

• All dash cams are programmed to automatically record when there is power

connected and a memory card inserted. When the engine is turned off, or

power is disconnected, the dash cam will stop recording approximately

after 3-10 secs. Manually start/stop recording by pressing the 'OK/Rec'

button (6).

-18-

6 Customer Support

For customer support inquiries please contact:

[email protected]

Or visit our website: www.z-edge.com

Your opinion matters

Z-Edge is committed to improving our products to bring you the best user

experience. We value your feedback and encourage you to share your

experience with other shoppers.

You can also send us your thoughts and feedback on social media and follow us

on Facebook (www.facebook.com/zeroedgeGA/) & YouTube to get the latest

news, reviews, discounts and giveaways.

Thank you for choosing Z-Edge!

7 Warranty

All Zero Edge customers have a 30-day money back guarantee, to make sure

your shopping experience is worry-free.

You also get a 12 month warranty; if you subscribe to our official website

(www.zeroedgetechnology.com/) you can extend the warranty to 18 months.

You will receive notifications and introductions about our new products before

they are released to the market. Additionally, you could be selected to enjoy a

special discount or coupon if purchasing our products for detailed evaluation.

ページを読み込んでいます...

Z-EDGE Z-EDGE Z3D Dash Cam Dual Cameras on a Budget, Z3D Dash Cam Dual Cameras on a Budget ユーザーガイド

関連論文

その他の書類