Hitachi CG 23EC (LB) Handling Instructions Manual

Handling instructions

취급 설명서

Hướng dẫn sử dụng

คูมือการใชงาน

CG 23EC (SL) / CG 23EC (SLB)

en

zh

ko

vi

th

ar

CG23EC (SL)

en

zh

ko

vi

th

ar

2

1

23

1/3

2/3

M

T

U

V

S

CG23EC(SL)

G

R

D

CG23EC(SLB)

H

B

N

P

F

J

1

2

3

4

5

6

7

P

D

F

Q

G

H

I

J

N

B

E

L

O

A

C

P

K

W

3

456

7910

81112

13 14

12

13

15

14

16

17

18

17

9

10

11

12

8

4

15 16 17

18 19 20

21 22 23

24 25 26

1/3

2/3

22

17

18

19

20

21

23

24

25

AA

B

26

5

27 28 29

30 31 32

33 34 35

36 37 38

15

31

10 cm

32

33

35

34

23

27

0.6 mm

28

29

30

6

39 40

11-14 cm 11-14 cm

1.9-2.2 cm

36

English

7

MEANINGS OF SYMBOLS

NOTE: Some units do not carry them.

Symbols

WARNING

The following show symbols used for the machine. Be sure that you understand their meaning before use.

Brush Cutter / Grass Trimmer Guaranteed sound power level

It is important that you read, fully understand

before use, and observe the following safety

precautions and warnings. Careless or improper

use of the unit may cause serious or fatal injury.

Blade thrust may occur when the spinning

blade contacts a solid object in the critical area.

A dangerous reaction may occur causing the

entire unit and operator to be thrust violently.

This reaction is called blade thrust. As a result,

the operator may lose control of the unit which

may cause serious or fatal injury. Blade thrust is

more likely to occur in areas where it is diﬃ cult

to see the material to be cut.

Read, understand and follow all warnings and

instructions in this manual and on the unit.

Always wear eye, head and ear protectors when

using this unit.

Hot Surface – Contact with hot surface can

cause serious burns.

Do not use metal/rigid blades when this sign is

shown on the unit.

Indicate handle location. Arrows which show

limits for handle positioning.

Keep all children, bystandards and helpers

15 m away from the unit. If anyone approaches

you, stop the engine and cutting attachment

immediately.

Displacement

Be careful of thrown objects. Spark plug

min

-1

Shows maximum shaft speed. Do not use the

cutting attachment whose max rpm is below the

shaft rpm.

Idle

Idling speed

Gloves should be worn when necessary, e.g.,

when assembling cutting equipment.

Speed of output shaft

Use anti-slip and sturdy footwear.

P

Max. engine output

Choke – Run position (Open) Fuel tank capacity

Choke – Start position (Closed)

Dry weight (without fuel, cutting attachment,

harness and cutting attachment guard)

START

On/Start Cutting attachment

STOP

Oﬀ /Stop

L

pA, eq

ISO22868

Sound pressure level LpA by ISO 22868

Equivalent*

Fuel and oil mixture

L

WA, Ra(M)

2000/14/EC

Measured sound power level LwA by 2000/14/

EC

Racing

Idle speed adjustment

L

WA, Ra(G)

2000/14/EC

Guaranteed sound power level LwA by

2000/14/EC

Racing

Priming pump

a

hv, eq(F)

Vibration level by ISO 22867

Front or Left handle / Equivalent*

English

8

a

hv, eq(R)

Vibration level by ISO 22867

Rear or Right handle / Equivalent*

K

Uncertainty

Before using your machine

• Read the manual carefully.

• Check that the cutting equipment is correctly assembled and adjusted.

• Start the unit and check the carburetor adjustment. See “MAINTENANCE”.

NOTE: Equivalent noise level / vibration level are calculated as the time-weighted energy total for noise / vibration levels

under various working conditions with the following time distribution:

* 1/2 Idle, 1/2 racing.

WHAT IS WHAT? (Fig. 1)

Since this manual covers several models, there may be

some diﬀ erence between pictures and your unit. Use the

instructions that apply to your unit.

A: Fuel cap

B: Throttle trigger

C: Starter handle

D: Cutting attachment guard

E: Guard extension

F: Cutting attachment

G: Drive shaft tube

H: Handle

I: Hanger

J: Ignition switch

K: Spark plug

L: Priming pump

M: Harness

N: Throttle trigger lockout

O: Choke lever

P: Engine

Q: Gear case

R: Cutter case

S: Combi box spanner

T: Handling instructions

U: Goggles

V: Hex bar wrench

W: Top cover

WARNINGS AND SAFETY

INSTRUCTIONS

Pay special attention to statements preceded by the

following words:

WARNING

Indicates a strong possibility of severe personal injury or

loss of life, if instructions are not followed.

CAUTION

Indicates a possibility of personal injury or equipment

damage, if instructions are not followed.

NOTE

Helpful information for correct function and use.

Operator safety

○ Wear head protection (1). (Fig. 2)

○ Always wear a safety face shield or goggles (2). (Fig. 2)

○ Wear approved hearing protection (3). (Fig. 2)

Long-term exposure to noise can result in permanent

hearing impairment.

Pay attention to your surroundings. Be aware of any

bystanders who may be signaling a problem.

Remove safety equipment immediately upon shutting oﬀ

engine.

○ Always wear heavy, long-sleeved shirts (4) and long

pants (5) and non-slip boots (6) and gloves (7). (Fig. 2)

Do not wear loose clothing, jewelry, short pants, sandals

or go barefoot.

Secure hair so it is above shoulder length.

○ Do not operate this tool when you are tired, ill or under

the inﬂ uence of alcohol, drugs or medication.

○ Do not operate the tool at night or under bad weather

conditions when visibility is poor. And do not operate the

tool when it is raining or right after it has been raining.

Working on slippery ground could lead to an accident if

you lose your balance.

○ Never let a child or inexperienced person operate the

machine.

○ Do not start the engine if there are any ﬂ ammables such

as dry leaves, waste paper or fuel in the vicinity.

○ Never start or run the engine inside a closed room or

building. Breathing exhaust fumes can kill.

○ Keep handles free of oil and fuel.

○ Keep hands away from cutting equipment.

○ Do not grab or hold the unit by the cutting equipment.

○ Gloves should be worn when installing or removing the

cutting attachment. Failure to do so may result in injury.

○ When the unit is shut oﬀ , make sure the cutting

attachment has stopped before the unit is set down.

○ When operation is prolonged, take a break periodically

so that you may avoid possible Hand-Arm Vibration

Syndrome (HAVS) which is caused by vibration.

WARNING

○ Always operate the tool with proper protective equipment

and clothing. Failure to do so may result in accidents

such as burns or injuries. (Fig. 2)

○ Do not touch the spark plug area or high voltage during

operation. Doing so may result in electric shock.

○ Do not allow children near the tool during operation.

○ Do not touch the engine, top cover or exhaust vent

during or shortly after operation. Doing so may result in

burn or injury.

○ Antivibration systems do not guarantee that you will

not sustain Hand-Arm Vibration Syndrome or carpal

tunnel syndrome. Therefore, continual and regular users

should monitor closely the condition of their hands and

ﬁ ngers. If any of the above symptoms appear, seek

medical advice immediately.

○ If you are using any medical electric/electronic devices

such as a pacemaker, consult your physician as well as

the device manufacturer prior to operating any power

equipment.

Unit/machine safety

○ Inspect the entire unit/machine before each use.

Replace damaged parts. Check for fuel leaks and make

sure all fasteners are in place and securely tightened.

○ Replace parts that are cracked, chipped or damaged in

any way before using the unit/machine. Faulty parts may

increase the risk of accidents and may lead to an injury.

○ Make sure the cutting attachment guard and harness are

properly attached. Do not operate if cutting attachment

guard and harness is not properly attached.

English

9

○ Keep others away when making carburetor adjustments.

○ Use only accessories as recommended for this unit/

machine by the manufacturer.

○ Before operation, make sure that there are no tools such

as the adjustment key or spanner still attached to the

unit.

WARNING

○ Never modify the unit/machine in any way. Do not use

your unit/machine for any job except that for which it is

intended.

○ Non-authorized modiﬁ cations and/or accessories may

result in serious personal injury or the death of the

operator or others.

Fuel safety

○ Mix and pour fuel outdoors and where there are no

sparks or ﬂ ames.

○ Use a container approved for fuel.

○ Move at least 3 m away from fueling site before starting

engine.

○ Stop engine before removing fuel cap. Do not remove

the fuel cap during operation.

○ Empty the fuel tank before storing the unit/machine. It is

recommended that the fuel be emptied after each use. If

fuel is left in the tank, store so fuel will not leak.

WARNING

○ Fuel is easy to ignite or get explosion or inhale fumes, so

that pay special attention when handling or ﬁ lling fuel.

○ Do not smoke or allow smoking near fuel or the unit/

machine or while using the unit/machine.

○ Wipe up all fuel spills before starting engine.

○ Store unit/machine and fuel in area where fuel vapors

cannot reach sparks or open ﬂ ames from water heaters,

electric motors or switches, furnaces. etc.

○ When using the unit in dry areas, make sure that ﬁ re

extinguishing equipment is readily available.

○ If you shut oﬀ the engine for refueling, make sure the unit

has cooled down before adding fuel.

Cutting safety

○ Do not cut any material other than grass and brush.

○ Inspect the area to be cut before each use.

Remove objects which can be thrown or become

entangled.

Do not operate in areas where there are tree roots or

rocks.

○ For respiratory protection, wear an aerosol protection

mask when cutting the grass after insecticide is

scattered.

○ Keep others including children, animals, bystanders and

helpers outside the 15 m hazard zone. Stop the engine

immediately if you are approached.

○ Please exercise caution as engine startup may be

delayed after pulling the starter handle.

○ Always keep the engine on the right side of your body.

○ Hold the unit/machine ﬁ rmly with both hands.

○ Keep ﬁ rm footing and balance. Do not over-reach.

Losing your balance during work may lead to an injury.

○ Keep all parts of your body away from the muﬄ er and

cutting attachment when the engine is running.

○ Keep cutting attachment below knee level.

○ Please exercise caution when operating in areas where

electrical cables or gas pipes are present.

○ Do not operate the cutting attachment for anything but

clearing grass or bushes. Avoid operations where the

cutting attachment may touch water such as puddles

or dig into dirt. Failure to do so may result in injury or

damage to the unit.

○ Avoid prolonged use at low speed range in which

vibration is high. Doing so may result in engine damage.

○ When relocating to a new work area, or inspecting,

adjusting or exchanging the unit’s cutting attachments,

accessories, etc., be sure to shut oﬀ the machine and

ensure that all cutting attachments are stopped.

○ Never place the machine on the ground when running.

○ Never touch the cutting attachment when it is rotating.

○ Always ensure that the engine is shut oﬀ and any cutting

attachments have completely stopped before clearing

debris or removing grass from the cutting attachment.

○ Always carry a ﬁ rst-aid kit when operating any power

equipment.

○ Turn oﬀ the engine and make sure the cutting attachment

has come to a full stop before removing the unit from

your body or before leaving the unit unattended.

○ If you accidentally bump or drop the unit, inspect it

immediately to make sure there are no damage, cracks

or deformations.

○ If the tool is operating poorly and produces strange noise

or vibrations, turn oﬀ the engine immediately and ask

your dealer to have it inspected and repaired.

Continued use under these conditions could lead to

injury or tool damage.

○ Use in accordance with local laws and regulations.

WARNING

KICKBACK DANGER (Fig. 3)

When using metal cutting attachments such as blades,

contact with obstacles such as trees or other hard

surfaces with the front or right portion of the spinning

attachment may force the unit to catch on an obstacle,

resulting in a kickback reaction towards the right side of

the operator.

Kickback may occur when the cutting attachment comes

into contact with tree stumps or rocks hidden behind

weeds. Always make sure there are no obstacles hidden

by weeds before starting work.

To minimize the danger of kickbacks when they do occur,

always position the unit to the right side of the body

during operation. With the operator properly positioned

as the cutting attachment rotates, this will reduce the

danger of the unit’s direct contact with the body.

Maintenance safety

○ Maintain the unit/machine according to recommended

procedures.

○ Disconnect the spark plug before performing

maintenance except for carburetor adjustments.

○ Keep others away when making carburetor adjustments.

○ Use only genuine HITACHI replacement parts as

recommended by the manufacturer.

CAUTION

Do not disassemble the recoil starter. There is a

possibility of personal injury with recoil spring.

WARNING

Improper maintenance could result in serious engine

damage or in serious personal injury.

Transport and storage

○ Carry the unit/machine by hand with the engine stopped

and the muﬄ er away from your body.

○ Allow the engine to cool, empty the fuel tank, and secure

the unit/machine before storing or transporting. Failure to

do so may result in ﬁ re or accidents.

○ Empty the fuel tank before storing the unit/machine. It is

recommended that the fuel be emptied after each use. If

fuel is left in the tank, store so fuel will not leak.

○ Store unit/machine out of the reach of children.

○ Clean and maintain the unit carefully and store it in a dry

place.

○ Make sure engine switch is oﬀ when transporting or

storing.

○ When transporting and storing, either remove the cutting

attachment or place the blade cover over the blade.

English

10

○ You have to secure the machine during transport to

prevent loss of fuel, damage or injury.

○ If a warning label cannot be read, peels oﬀ or becomes

indistinct, replace it with a new one. To purchase new

labels, contact Hitachi Authorized Service Centers.

If situations occur which are not covered in this manual, take

care and use common sense. Contact Hitachi Authorized

Service Centers if you need assistance.

SPECIFICATIONS

The SPECIFICATIONS of this machine are listed in the table

on page 74.

NOTE

All data subject to change without notice.

ASSEMBLY PROCEDURES

Installation of handle

Loop handle type (Fig. 4)

Attach the handle to the drive shaft tube.

Adjust the location to the most comfortable position before

operation.

Make sure to securely attach the handle with the 4 bolts.

NOTE

If your unit has handle location label (8) on drive shaft

tube, follow the illustration.

Installation of harness

(If so equipped)

WARNING

If the product includes a harness, always make sure to

use it.

Attach the harness hook (9) to the hanger (10) on the drive

shaft tube. (Fig. 5)

Adjust the length of the harness for easy operation of the

tool.

NOTE

You may need to adjust the position of the hangar (10)

to balance the unit. To do so, loosen bolt (11) and adjust

the position of hangar (10). After adjusting as necessary,

make sure to securely tighten the bolt (11). (Fig. 5)

Installation of cutting attachment guard

WARNING

If an incorrect or faulty guard is ﬁ tted, this may cause

serious personal injury.

CAUTION

Some cutting attachment guards are equipped with

sharp line limiters. Be careful with handling it.

NOTE

○ When using a trimmer head with two piece type cutting

attachment guard, attach the guard extension to the

cutting attachment guard, then tighten the bolt (12).

(Fig. 6)

○ The guard bracket may come already mounted to the

gear case on some models.

Align the cutting attachment guard with the guard bracket (13)

and secure it to the drive shaft tube, using the bolt. (Fig. 7)

WARNING

Remove the guard extension when using metal or plastic

blades. Failure to do so may result in injury or damage to

the cutting attachment guard.

NOTE

To remove the guard extension, refer to the drawings.

Wear gloves as the extension has a sharp line limiter.

Loosen the bolt (12). Then push the three square tabs on

the guard one by one in order. (Fig. 8)

(CG23EC (SLB))

Insert the cutter case between the guard bracket and cutting

attachment guard, and secure it with the bolt. (Fig. 9)

Installation of cutting attachment

WARNING

○ Install the cutting attachment properly and securely as

instructed in the handling instructions.

If not attached properly or securely, it may come oﬀ and

cause serious and/or fatal injury.

○ Do not install or remove cutting attachments while the

engine is running.

○ Always use genuine Hitachi cutting attachments and

metal ﬁ ttings.

Installation of semi-auto cutting head

1. Function

Automatically feeds more nylon cutting line when it is

tapped at low rpm (not greater than 6000 /min).

Speciﬁ cations

Code

No.

Type of

attaching

screw

Direction of

rotation

Size of

attaching

screw

6600570 Female screw

Counter-

clockwise

M10xP1.25-

LH

6601272 Female screw Clockwise

M8xP1.25-RH

Applicable nylon cord

Cord diameter: Φ2.4 mm Length: 5 m

2. Precautions

○ The case must be securely attached to the cover.

○ Check the cover (14), case (15) and other components

for cracks or other damage. (Fig. 10)

○ Check the case and button for wear.

If there is a hole in the bottom (16) of the button, change

the new parts immediately. (Fig. 10)

○ The cutting head must be securely mounted to the unit’s

gear case/cutter case.

○ If the cutting head does not feed cutting line properly,

check that the nylon line and all components are properly

installed. Contact Hitachi Authorized Service Centers if

you need assistance.

WARNING

For Hitachi heads, use only ﬂ exible, non-metallic line

recommended by the manufacturer. Never use wire or

wire ropes. They can break oﬀ and become a dangerous

projectile.

3. Installation

(CG23EC (SL)) (Fig. 11)

Insert the Hex bar wrench (17) into the hole of the gear

case and groove of the Cutter holder (A) (18) in order to

lock the shaft.

Install cutting head on gear case of brush cutters. The

mounting nut is left-hand-threaded. Turn clockwise to

loosen/counter-clockwise to tighten.

NOTE

Since the cutter holder cap is not used here, keep it for

when a metal blade is used, if so equipped.

(CG23EC (SLB)) (Fig. 12)

Insert the Hex bar wrench (17) into the hole of the cutter

case in order to lock the drive shaft tube.

English

11

Install cutting head on cutter case of grass trimmers.

The mounting nut is right-hand-threaded. Turn counter-

clockwise to loosen/clockwise to tighten.

4. Adjusting line length

Set the engine speed as low as possible and tap the

head on the ground. The nylon line will be drawn out

about 3 cm with each tap. (Fig. 13)

Also, you can extend the nylon line by hand but the

engine must be completely stopped. (Fig. 14)

Adjust the nylon line to the proper length of 11–14 cm

before each operation.

Installation of cutting blade (Fig. 15)

(If so equipped)

Insert the Hex bar wrench (17) into the hole of the gear case

and groove of the Cutter holder (A) (18) in order to lock the

shaft.

Assemble in the following order: Cutter holder (A) (18),

blade (19), cutter holder (B) (20), nut cover (21).

Tighten the ﬁ xing nut with the combi box spanner with a

tightening torque of 14

±

2 N.m. Please note that the cutter

ﬁ xing nut (22) has left-handed threads (clockwise to loosen/

counter-clockwise to tighten).

NOTE

○ When installing cutter holder (B) (20), be sure to set

concave side upward.

○ When installing or removing a blade, make sure to wear

gloves and place the blade cover over the blade.

CAUTION

Check a nut cover (21) for wear or cracks before

operation. If any damage or wear is found, replace it, as

it is an article of consumption.

WARNING

○ When installing a cutting blade, make sure that there are

no cracks or any damage in it and that the cutting edges

are facing the correct direction.

○ Remove any surface grit from blade installation ﬁ ttings

(cutter holder (A) (18), cutter holder (B) (20), nut

cover (21), nut (22)). Failure to do so may result in the

loosening of nuts.

○ The protrusion of the cutter holder (A) (18) may become

misaligned with the blade (19) while tightening nut

(22). Before operation, make sure the blade has been

properly installed. (Fig. 16)

○ Rotate the blade by hand and make sure there is no

rocking or abnormal noise. Rocking may cause abnormal

vibrations or result in the loosening of nuts.

OPERATING PROCEDURES

Fuel (Fig. 17)

WARNING

○ The trimmer is equipped with a two-stroke engine.

Always run the engine on fuel, which is mixed with oil.

Provide good ventilation, when fueling or handling fuel.

○ Fuel is highly ﬂ ammable and it is possible to get seriously

injured when inhaling or spilling on your body.

Always pay attention when handling fuel. Always have

good ventilation when handling fuel inside building.

Fuel

○ Always use branded 89 octane unleaded gasoline.

○ Use genuine two-cycle oil or use a mix between 25:1 to

50:1, please consult about the mixture ratio to Hitachi

Authorized Service Centers.

○ If genuine oil is not available, use an anti-oxidant added

quality oil expressly labeled for air-cooled 2-cycle engine

use (JASO FC GRADE OIL or ISO EGC GRADE). Do not

use BIA or TCW (2-stroke water-cooling type) mixed oil.

○ Never use multi-grade oil (10 W/30) or waste oil.

○ Never mix fuel and oil in machine’s fuel tank. Always mix

fuel and oil in a separate clean container.

Always start by ﬁ lling half the amount of gasoline, which is

to be used.

Then add the whole amount of oil. Mix (shake) the fuel

mixture. Add the remaining amount of gasoline.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the fuel

tank.

Mixing amount of two-cycle oil and gasoline

Gasoline (Liter)

Two-cycle oil (ml)

Ratio 50:1 Ratio 25:1

0.5 10 ——— 20

1 20 ——— 40

2 40 ——— 80

4 80 ——— 160

Fueling

WARNING

○ Always shut oﬀ the engine and let it cool for a few

minutes before refueling.

Do not smoke or bring ﬂ ames or sparks near the fueling

site.

○ Slowly open the fuel tank, when ﬁ lling up with fuel, so

that possible over-pressure disappears.

○ Tighten the fuel tank cap carefully, after fueling.

○ Always move the unit at least 3 m from the fueling area

before starting.

○ Always wash any spilled fuel from clothing immediately

with soap.

○ Be sure to check any fuel leakage after refueling.

○ Before fueling, in order to remove static electricity from

the main body, the fuel container and the operator,

please touch the ground that is slightly damp.

Before fueling, clean the tank cap area carefully, to ensure

that no dirt falls into the tank. Make sure that the fuel is well

mixed by shaking the container, before fueling.

Starting

WARNING

○ Before starting the tool, ensure that the cutting

attachment is not touching any objects or the ground.

Otherwise, the cutting attachment may unexpectedly

rotate and cause an injury.

○ Ensure that the cutting attachment does not rotate while

the engine is idling. If it does rotate, adjust the idle speed

according to the instructions in “Idle speed adjustment” in

the “MAINTENANCE” section. If the cutting attachment

still rotates after this adjustment, immediately stop the

engine and cease use, then bring the tool to the nearest

Hitachi Authorized Service Center.

(1) Starting the cold engine

1. Set ignition switch (23) to ON position. (Fig. 18)

2. Push priming pump (24) several times so that fuel ﬂ ows

through return pipe (25). (Fig. 19)

3. Set choke lever (26) to START position (closed) (A).

(Fig. 20)

4. Pull recoil starter briskly, taking care to keep the handle

in your grasp and not allowing it to snap back. (Fig. 21)

5. When you hear the engine want to start, return choke

lever to RUN position (open) (B). (Fig. 20)

6. Pull recoil starter briskly again. (Fig. 21)

NOTE

If engine does not start, repeat procedures from 2 to 5.

7. Then allow the engine about 2–3 minutes to warm up

before subjecting it to any load.

8. Check that the cutting attachment does not rotate when

the engine is idling.

English

12

(2) Starting the warm engine

Use only 1, 6 and 8 of the starting procedure for a cold

engine.

If the engine does not start, use the same starting

procedure as for a cold engine.

Cutting

WARNING

○ Always use the harness (if so equipped) and wear the

proper attire and protective equipment when operating

the unit. (Fig. 22)

○ Keep others including children, animals, bystanders and

helpers outside the 15 m hazard zone. Stop the engine

immediately if you are approached. (Fig. 23)

○ When grass or vines wrap around attachment, stop engine

and attachment and remove them. Continuing operation

with grass or vines wrapped around the attachment may

result in damages such as early abrasion of the clutch.

CAUTION

Use and points of caution will vary depending on the type

of cutting attachment. For safe use, make sure to follow

the instructions and guidelines provided with each type.

NOTE

○ Press the quick release button or pull emergency release

ﬂ ap (If so equipped) in the event of emergency. (Fig. 24)

○ Use in accordance with local laws and regulations.

(1) Using a semi-auto cutting head

○ Set the engine at high speed when using this attachment.

○ Cut grass from left to right. The cut grass will be

discharged away from the body, minimizing transfer to

your clothes. (Fig. 25)

○ Cut grass from right to left as the cutting attachment of

the curved drive shaft tube model rotates clockwise.

○ With nylon cord, use about 2 cm of the end of the cord

to cut grass. Using the full length of the cord will reduce

rotation speed and make cutting diﬃ cult.

NOTE

Automatically feeds more nylon cutting line when it is

tapped at low rpm (not greater than 6000 /min).

WARNING

○ This product is equipped with a line limiter that will

automatically cut any excess cord. When operating the

unit, do not remove the guard or line limiter.

As the resistance is greater for nylon cords as opposed

to blades, mishandling could increase engine load and

result in damage.

○ Do not use with the engine set at low speeds. If the

engine speed is low, grass may wrap around the

attachment, causing the clutch to slip which could result

in clutch abrasion.

○ With nylon cord cutters, always use over 15 cm of cord.

If the length of the cord is too short, rotation speed will

increase and may cause damage to the nylon cord

cutter. As the curved drive shaft tube model in particular

is not equipped with a deceleration mechanism, the

possibility of increased rotation speed for the cutting

attachment is high.

(2) Using a blade

○ Adjust engine speed according to the resistance of the

grass. For soft grass, use low speeds, For tough clumps

of grass, use high speeds.

○ Cut grass from right to left, using the left side of the blade

to cut. (Fig. 26)

○ Slightly tilting the blade to the left while cutting will pile

the cut grass to the left, making collection easy.

NOTE

Excessively increasing rotation speed may cause

increased blade wear, vibration and noise. It will also

result in increased fuel consumption.

WARNING

○ Blade thrust may occur when the spinning blade contacts

a solid object in the critical area.

A dangerous reaction may occur causing the entire unit

and operator to be thrust violently. This reaction is called

blade thrust. As a result, the operator may lose control

of the unit which may cause serious or fatal injury. Blade

thrust is more likely to occur in areas where it is diﬃ cult

to see the material to be cut.

○ If cutting attachment should strike against stones or

other debris, stop the engine and make sure that the

attachment and related parts are undamaged.

Stopping (Fig. 27)

Decrease engine speed and run at an idle for a few minutes,

then turn oﬀ ignition switch (23).

WARNING

A cutting attachment can injure while it continues to spin

after the engine is stopped or Throttle trigger is released.

When the unit is turned oﬀ , make sure the cutting

attachment has stopped before the unit is set down.

MAINTENANCE

MAINTENANCE, REPLACEMENT OR REPAIR OF THE

EMISSION CONTROL DEVICES AND SYSTEMS MAY

BE PERFORMED BY ANY NON-ROAD ENGINE REPAIR

ESTABLISHMENT OR INDIVIDUAL.

Carburetor adjustment (Fig. 28)

The carburetor is a precision part that mixes air and fuel, and

it is designed to ensure high performance from the engine.

Before the tool is shipped from the factory, its carburetor is

adjusted during a test run. Only make adjustments if it is

necessary because of environmental conditions (the climate

or atmospheric pressure), the type of fuel, the type of two-

cycle oil, etc.

WARNING

○ Because the carburetor is manufactured with a high

degree of precision, do not disassemble it.

○ For this product, the only setting of the carburetor that

can be adjusted is the idle speed (T).

○ Never start the engine without the complete clutch cover

and tube assembled! Otherwise the clutch can come

loose and cause personal injuries.

T = Idle speed adjustment screw.

Idle speed adjustment (T)

WARNING

○ When the engine is stopped, do not excessively turn

the idle speed adjustment screw (T) in a clockwise

direction. Otherwise, when the engine starts, the cutting

attachment may unexpectedly rotate and cause an

injury.

○ Do not adjust the idle speed adjustment screw (T) for

any reason other than to adjust the idling.

Run the engine while adjusting the idling.

(1) If the engine stops during idling

Start the engine, and slowly turn the idle speed

adjustment screw (T) in a clockwise direction until it is in

a position at which the engine rotates smoothly. At that

time, ensure that the cutting attachment is not spinning.

(2) If the cutting attachment rotates during idling

Slowly turn the idle speed adjustment screw (T) in a

counter-clockwise direction until it is in a position at

which the cutting attachment does not rotate. At that

time, ensure that the rotation of the engine is smooth.

English

13

WARNING

If the cutting attachment still rotates after adjustment of

the idle speed adjustment screw (T), immediately stop

the engine and cease use, then contact the nearest

Hitachi Authorized Service Center.

Air ﬁ lter (Fig. 29)

The air ﬁ lter (27) must be cleaned from dust and dirt in order

to avoid:

○ Carburetor malfunctions.

○ Starting problems.

○ Engine power reduction.

○ Unnecessary wear on the engine parts.

○ Abnormal fuel consumption.

Clean the air ﬁ lter daily or more often if working in

exceptionally dusty areas.

Open the air ﬁ lter cover and remove the air ﬁ lter (27). Clean

it.

Check that the ﬁ lter is dry before reassembly.

An air ﬁ lter that has been used for some time cannot be

cleaned completely. Therefore, it must regularly be replaced

with a new one. A damaged ﬁ lter must always be replaced.

NOTE

To put the air ﬁ lter cover back into place, hook it on the

upper tabs and then attach it.

Fuel ﬁ lter (Fig. 30)

Remove the fuel ﬁ lter (28) from the fuel tank, and replace it if

it is dirty.

NOTE

A blocked fuel ﬁ lter (28) can prevent the supply of fuel and

cause a rotation malfunction of the engine.

Spark plug (Fig. 31)

The spark plug condition is inﬂ uenced by:

○ An incorrect carburetor setting.

○ Wrong fuel mixture (too much oil in the gasoline)

○ A dirty air ﬁ lter.

○ Hard running conditions (such as cold weather).

These factors cause deposits on the spark plug electrodes,

which may result in malfunction and starting diﬃ culties. If

the engine is low on power, diﬃ cult to start or runs poorly at

idling speed, always check the spark plug ﬁ rst.

If the spark plug is dirty, clean it and check the electrode

gap. Re-adjust if necessary. The correct gap is 0.6 mm. The

spark plug should be replaced after about 100 operation

hours or earlier if the electrodes are badly eroded.

NOTE

In some areas, local law requires using a resistor spark

plug to suppress ignition signals. If this machine was

originally equipped with resistor spark plug, use same

type of spark plug for replacement.

Flexible drive shaft (Fig. 32)

(CG23EC (SLB))

Flexible drive shaft should be removed and lubricated with

good quality lithium grease every 20 hours. To remove the

ﬂ exible shaft, ﬁ rst remove screw (29), loosen bolt (30) and

remove the cutter case then pull the shaft out of the drive

shaft tube. Clean the shaft oﬀ and apply a generous coat of

lithium grease to it and insert if back into the drive shaft tube,

turn it unit it drops into place then install the cutter case,

install & tighten screw (29) and bolt (30).

Gear case (Fig. 33)

Check gear case or angle gear for grease level about every

50 hours of operation by removing the grease ﬁ ller plug on

the side of gear case.

If no grease can be seen on the ﬂ anks of the gears, ﬁ ll the

gear case with quality lithium based multipurpose grease up

to 3/4. Do not completely ﬁ ll the gear case.

CAUTION

○ Make sure to remove any dirt or grit when attaching the

plug to its original position.

○ Before attempting inspection or maintenance of the gear

case, make sure the case has cooled.

Semi-auto cutting head

Nylon line replacement

1. Remove the case (15) by ﬁ rmly pushing inward the

locking tabs with your thumbs as shown in Fig. 34.

2. After removing the case, take out the reel and discard

the remaining line.

3. Fold the new nylon line unevenly (approx. 10 cm) in half

as shown in picture.

Hook the U-shaped end of the nylon line into the groove

(31) on the center partition of the reel.

Wind both halves of the line on the reel in the same

direction, keeping each half of the line on its own side of

the partition. (Fig. 35)

4. Push each line into the stopper holes (32), leaving the

loose ends approx. 10 cm in length. (Fig. 36)

5. Insert both loose ends of the line through the cord guide

(33) when placing the reel in the case. (Fig. 37)

NOTE

When placing a reel in the case, try to line up the stopper

holes (32) with the cord guide (33) for easier line release

later.

6. Place the cover over the case so that the cap locking

tabs (35) on the cover meet the long holes (34) on the

case. Then push the case securely until it clicks into

place. (Fig. 38)

7. The initial cutting line length should be approx. 11–14 cm

and should be equal on both sides. (Fig. 39)

Blade (Fig. 40)

WARNING

Wear protective gloves when handling or performing

maintenance on the blade.

○ Use a sharp blade. A dull blade is more likely to snag and

thrust.

Replace the fastening nut if it is damaged and hard to

tighten.

○ When replacing blade, purchase one recommended by

Hitachi, with a 25.4 mm (one inch) ﬁ tting hole.

○ In the case of a 3 tooth blade (36), it can be used on

either side.

○ Use the correct blade for the type of work.

○ When replacing blades, use appropriate tools.

○ When cutting edges become dull, re-sharpen or ﬁ le

as shown in the illustration. Incorrect sharpening may

cause excessive vibration.

○ Discard blades that are bent, warped, cracked, broken

or damaged in any way.

NOTE

When sharpening blade it is important to maintain an

original shape of radius at the base of the tooth to avoid

cracking.

For long-term storage

Drain all fuel from the fuel tank. Start and let engine run until

it stops. Repair any damage which has resulted from use.

Clean the unit with a clean rag, or the use of high pressure

air hose. Put a few drops of two-cycle engine oil into the

cylinder through the spark plug hole, and spin the engine

over several times to distribute oil.

Cover the unit and store it in a dry area.

Maintenance schedule

Below you will ﬁ nd some general maintenance instructions.

For further information please contact Hitachi Authorized

Service Centers.

English

14

Daily maintenance

○ Clean the exterior of the unit.

○ Check that the harness is undamaged.

○ Check the cutting attachment guard for damage or

cracks. Change the guard in case of impacts or cracks.

○ Check that the cutting attachment is properly centered,

sharp, and without cracks. An oﬀ -center cutting

attachment induces heavy vibrations that may damage

the unit.

○ Check that the cutting attachment nut is suﬃ ciently

tightened.

○ Make sure that the blade cover is undamaged and that it

can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently tightened.

○ Check that the unit is undamaged and free of defects.

Weekly maintenance

○ Check the starter, especially the cord.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode gap.

Adjust it to 0.6 mm, or change the spark plug.

○ Check that the angle gear is ﬁ lled with grease up to 3/4.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline.

○ Clean the exterior of the carburetor and the space

around it.

○ Clean the fan and the space around it.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 75.

English

15

SELECTING CUTTING ATTACHMENTS

Recommended accessories for each model are presented in the table below.

For purchases, contact Hitachi Authorized Service Centers.

Please check carefully as those accessories not marked with “

●” cannot be attached.

List of recommended accessories

Type Name

Speciﬁ cation LOOP HANDLE

Diameter

Feed System Adapter

or

No. of Teeth (Blade)

Blade Thickness (mm)

or

Trimmer line Diameter

(mm)

CG23EC (SLB)

CG23EC (SL)

ALUMINUM HEADS

NYLON HEAD

CH-100

(W/NYLON LINE)

4” Pre-Cut Line 2.2 – 3.0

●

NYLON HEAD

CH-100

●

TAP & GO NYLON

HEADS

NYLON HEAD

BF-4

4” R M8 x 1.25 Nut 2.2 – 3.0

●

NYLON HEAD

BF-5

5”

L M10 x 1.25 Nut

L M8 x 1.25 Nut

2.2 – 3.0

●

BLADES

BLADE

B4/9/1.6

9” 4 1.6

BLADE

B4/10/1.6

10” 4 1.6

English

16

TROUBLESHOOTING

Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your

dealer or the Hitachi Authorized Service Center.

Condition Cause Remedy

Engine does not

start

Fuel

system

Fuel tank is empty or fuel level is low

Fill the fuel tank with the correct fuel mix

(25:1-50:1)

Fuel tank contains old fuel (oﬀ ensive odor)

Replace with new fuel

Too much fuel is absorbed and spark

plug is wet

1.

Disconnect the spark plug and allow to dry

2. Pull the starter handle 5 or 6 times to

remove the surplus fuel

3. Attach the spark plug

4. Set the choke lever to RUN position and

pull the starter handle

Fuel ﬁ lter is clogged with dirt Clean the fuel ﬁ lter

Fuel pipe is bent or disconnected Ensure that the fuel ﬂ ows smoothly

Carburetor malfunction Contact Hitachi Authorized Service Centers

Electrical

system

Stop switch lead has short-circuited Contact Hitachi Authorized Service Centers

Spark plug is dirty Replace or clean the spark plug

Electrode gap is too big Adjust the gap to 0.6mm

Poor connection between high tension

cable and spark plug

Reconnect

Electrical system malfunction Contact Hitachi Authorized Service Centers

Other

Muﬄ er exhaust port is clogged with

carbon

Contact Hitachi Authorized Service Centers

for repair

Engine starts

but cuts out

straightaway

Engine is apt to

cut out

Fuel

system

Fuel tank is empty or fuel level is low

Fill the fuel tank with the correct fuel mix

(25:1-50:1)

Fuel tank contains old fuel (oﬀ ensive odor)

Replace with new fuel

Two-cycle oil has not been added Contact Hitachi Authorized Service Centers

Choke lever is in START position Set the choke lever to RUN position

Air has got into fuel system Reconnect the fuel pipe or joint

Carburetor malfunction Contact Hitachi Authorized Service Centers

Electrical

system

Ignition failure

Spark plug failure Replace with new spark plug

Electrical system failure Contact Hitachi Authorized Service Centers

Other

Engine overheating

Wrong spark plug model

Replace with designated part

See “SPECIFICATIONS”

Dirty air cleaner Clean

Carbon clogging (muﬄ er exhaust port) Clean

Insuﬃ cient compression (piston, piston

ring, cylinder)

Contact Hitachi Authorized Service Centers

Abnormal vibration

Cutting attachment is not properly

installed

See “Installation of cutting attachment”

Handle, handle bracket or other

fastening part is loose

Check and tighten

Blade is bent or damaged Replace with new blade

Grass is wrapped round gear case/

cutter case

Remove grass

Engine is running but blade

does not move

Movement is poor

Grass is wrapped round gear case/

cutter case

Remove grass and dirt

English

17

Condition Cause Remedy

Engine does not stop Stop switch failure

Set the choke lever to START position to

stop the engine

Cease use immediately and contact Hitachi

Authorized Service Centers

Engine stops when throttle is

closed

Idle speed is too low

Contact Hitachi Authorized Service Centers

Blade continues rotating when

throttle is closed

Idle speed is too high

Throttle wire is too taut

Contact Hitachi Authorized Service Centers

18

min

-1

Idle

START

P

STOP

19

L

WA, Ra(G)

2000/14/EC

a

hv, eq(F)

L

pA, eq

ISO22868

a

hv, eq(R)

L

WA, Ra(M)

2000/14/EC

K

20

ページが読み込まれています...

Hitachi CG 23EC (LB) Handling Instructions Manual

このマニュアルも適しています

Hitachi CG 23EC (LB) Handling Instructions Manual

関連論文

その他のドキュメント