Zenoah Pole Saw PSJ2300 ユーザーマニュアル

ブランド: Zenoah

モデル: Pole Saw PSJ2300

カテゴリー: おもちゃ

タイプ: ユーザーマニュアル

このマニュアルも適しています

PSJ2300

PSJ2300

848-A57-93A0 (704)

OWNER’S MANUAL

POLE SAW

长柄锯

• Before using our products,

please read this manual

carefully to understand the

proper use of your unit.

• Keep this manual handy.

CAUTION

English

SAFETY FIRST

Instructions contained in warnings

within this manual marked with a

symbol concern critical points

which must be taken into

consideration to prevent possible

serious bodily injury, and for this

reason you are requested to read

all such instructions carefully and

follow them without fail.

■ WARNINGS IN THE MANUAL

This mark indicates instructions

which must be followed in order to

prevent accidents which could

lead to serious bodily injury or

death.

This mark indicates instructions

which must be followed, or it leads to

mechanical failure, breakdown, or

damage.

This mark indicates hints or

directions useful in the use of the

product.

NOTE

IMPORTANT

WARNING

Contents

1. Parts location............................3

2. Explanation of pictorials............4

3. Symbols on the machine ..........4

4. Safety precautions....................5

5. Set up .....................................13

6. Fuel and chain oil....................16

7. Operation................................17

8. Maintenance ...........................21

9. Troubleshooting guide ............27

10. Specifications..........................28

中文

安全第一

本说明书上记载的注意事项以及机器上

贴着的带有的警告标签，是表示有

发生人身事故危险的重要项目，务请认

真阅读并严格遵守。

■关于警告标志

表示如不遵守注意事项，便可能导致重

伤或死亡。

表示如不遵守注意事项，有可能致使机

器损伤或发生故障。

表示其他使用上必要的补充说明。

1. 各部分的名称 ....................................3

2. 警告标签及用法 .................................4

3. 操作装置符号 ....................................4

4. 正确使用须知 .....................................5

5. 组装 ......................................................13

6. 燃料 ......................................................16

7. 操作方法 .............................................17

8. 检修 ......................................................21

9. 故障排除指南 ..................................27

10. 产品主要数据 ..................................28

警告

重要

补充

English

1. Parts location

1. Loop handle

2. Suspension point

3. Stop switch

4. Throttle cable

5. Throttle trigger

6. Shaft tube

7. Knob bolt

8. Starter knob

9. Fuel tank

10. Primer pump

11. Choke lever

12. Air cleaner cover

13. Guide bar

14. Saw chain

15. Chain cover

16. Gear case

中文

1. 环形把手

2. 悬挂点

3. 止动开关

4. 加油钢丝

5. 加油扳机

6. 轴管

7. 旋钮螺栓

8. 起动器旋钮

9. 燃料箱

10. 初给泵

11. 进气杆

12. 空气滤清器盖

13. 导板

14. 锯链

15. 链盖

16. 齿轮箱

1. 各部分的名称

English

2. Explanation of pictorials

(1) Read owner's manual before

operating this machine.

(2) Wear head, eye and ear

protection.

(3) Warning/Attention

(4) The unit has not been

designed to provide protection

from electric shock in the

event of contact with overhead

electric lines.

If warning labels peel off or become

soiled and impossible to read, you

should contact the dealer from which

you purchased the product to order

new labels and affix them in the

required location(s).

Never remodel your machine

We won't warrant the machine, if

you use the remodeled machine or

you don't observe the proper

usage written in the manual.

WARNING

IMPORTANT

3. Symbols on the machine

For safe operation and maintenance,

symbols are carved in relief on the

machine. According to these

indications, please be careful not to

take a mistake.

(a) The port to refuel the "MIX

GASOLINE"

Position: FUEL TANK CAP

(b) The direction to close the choke

Position: AIR CLEANER COVER

(d). If you turn the rod by screwdriver

follow the arrow to the "MAX"

position, the chain oil flow more,

and if you turn to the "MIN"

position, less.

Position: Bottom of the power unit

中文

（1）阅读使用说明书

（2）戴头盔、防尘眼镜和耳塞

（3）警告／注意

（4）本机不能防止由于接触到高空电

线而导致的触电现象。

警告标签污损护剥落时，请到购买本品

的商店重新订购，及时更换。

改造机器非常危险，切勿改造。

擅自改造或用于使用说明书所记载的正

确的使用目的以外的用途时，将不能享

受厂家所提供的各种保障，故请提起注

意。

为便于使用操作和保养管理，操作装置

用标志符号来表示。请按这些标志符号

进行操作，注意避免发生失误。

（a）表示使用燃料的种类为“混合汽

油”。

标志符号表示部位：燃料缸盖。

（b）表示向该符号的方向操作控制杆

时，进气门便会关闭。

标志符号表示部位：空气滤清器

的盖子

（c）表示向该符号的方向操作控制杆

时，进气门便会开通。

标志符号表示部位：空气滤清器

的盖子

（d）如果使用螺丝刀按照以下所示箭

头方向将控制杆转至“MAX（最

大）”位置，则链条油的出油量

较大。如果将控制杆转至“MIN

（最小）”位置，则链条油的出

油量较小。

标志符号表示部位：电源底部。

2. 警告标签及用法

3 操作装置符号

重要

警告

English

4. Safety precautions

1. Read this manual carefully until

you completely understand and

follow all safety and operating

instructions.

2. Keep this manual handy so that

you may refer to it later

whenever any questions arise.

Also note, if you have any

questions which cannot be

answered herein, contact the

dealer from whom you

purchased the product.

3. Always be sure to include this

manual when selling, lending, or

otherwise transferring the

ownership of this product.

4. Never allow children or anyone

unable to fully understand the

directions given in the manual to

use the machine.

■ WORKING CONDITION

1. When using the product, you

should wear proper clothing and

protective equipment.

(1) Helmet

(2) Ear protectors

(3) Protection goggles or face

protector

(4) Thick work gloves

(5) Non-slip-sole work boots

2. And you should carry with you.

(1) Attached tools and files

(2) Properly reserved fuel

(3) Spare blade

(4) Things to notify your working

area (rope, warning signs)

(5) Whistle (for collaboration or

emergency)

Approaching or contacting

electric power lines with Pole

saw may cause serious injury or

death from electrocution.

Electricity can jump from one

point to another by means of

arcing or may be conducted

through damp branches.

Maintain a clearance of at least

15m between Pole saw and any

electrical line carrying live

current.

WARNING

警告

中文

靠近或接触长柄锯的电源线可能会导

致严重的伤亡。

电流可通过电弧或潮湿的物体传导。

请务必使长柄锯与任何带火线电流的

电线之间保持至少 15 m 的距离。

1. 请仔细通读本手册直至您完全理解

并遵循所有的安全注意事项和操作

说明。

2. 请将本手册存放在便于取阅之处，

便于您日后有疑问时查阅。同时请

注意，如果您有任何该手册无法解

决的疑问，请与销售本产品的经销

商联系。

3. 当销售、租借或转让本产品时，请

务必将本手册一并附上。

4. 切勿让儿童或任何无法完全理解本

手册中指导说明的人员使用本机。

■工作条件

1. 使用本产品时，应穿戴适当的衣物和

劳防用品。

（1）头盔

（2）耳罩

（3）护目镜或面罩

（4）厚的工作手套

（5）防滑工作靴

2. 您应携带：

（1）附带的工具和文件

（2）正确存放的燃料

（3）备用刀片

（4）标示工作区域的物品（绳子、警

告标记等）

（5）哨子（用于多人合作时或出现紧

急情况时）

（6）斧头或锯子（用于清除障碍物）

4. 正确使用须知

English

(6) Hatchet or saw (for removal of

obstacles)

3. Do not wear loose clothing,

jewelry, short trousers, sandals, or

go barefoot. Do not wear anything

which might be caught by a

moving part of the unit. Secure

hair so it is above shoulder length.

■ WORKING CIRCUMSTANCE

1. Never start the engine inside a

closed room or building. Exhaust

gases contain dangerous carbon

monoxide.

2. Never use the product:

a. when the ground is slippery or

when you can’t maintain a

steady posture.

b. At night, at times of heavy fog,

or at any other times when your

field of vision might be limited

and it would be difficult to gain a

clear view of the working area.

c. During rain storms, during

lightning storms, at times of

strong or gale-force winds, or at

any other times when weather

conditions might make it unsafe

to use the product.

■ WORKING PLAN

1. You should never use the product

when under the influence of

alcohol, when suffering from

exhaustion or lack of sleep, when

suffering from drowsiness as a

result of having taken cold

medicine or at any other time

when a possibility exists that your

judgment might be impaired or that

you might not be able to operate

the product properly and in a safe

manner.

2. When planning your work

schedule, allow plenty of time to

rest. Limit the amount of time over

which the product is to be used

continuously to somewhere

around 30–40 minutes per

session, and take 10–20 minutes

of rest between work sessions.

Also try to keep the total amount of

work performed in a single day

under 2 hours or less.

1. If you don’t observe the working

time, or working manner (See

■ USING THE PRODUCT),

WARNING

4. Safety precautions

警告

3. 请勿穿戴宽松的衣物、首饰、短裤、

便鞋或裸足。请勿佩戴任何可能会被

机器运动部件钩住的物品。将头发束

起，不得使其过肩。

■工作环境

1. 切勿在密闭的房间或建筑中启动引擎。

废气中含有有害的一氧化碳。

2. 切勿在以下情况下使用产品：

a. 当地板很滑或您无法保持稳定的

姿势时。

b. 夜晚、有大雾或其它您的视野可

能受到限制导致无法看清工作区域

时。

c. 暴雨、闪电、狂风或其它可能不

安全的天气条件下。

■工作计划

1. 在酒后、缺睡、服用感冒药物而昏昏

欲睡或在您的判断力可能有所下降或

可能无法以正确和安全的方式操作本

产品的情况下，切勿使用本产品。

2. 制订工作计划时，请留出充足的休

息时间。将连续使用本产品的时间限

制在每次 30_40 分钟，并且每个工

作阶段之间应休息 10_20 分钟。同

时，请尽量将每天的总操作时间控制

在 2 个小时以下。

1. 如果您不遵守规定的工作时间或工作

方式（请参见 # 使用本产品），则

可能导致重复性压迫损伤（RSI）。

如果您的手指或身体其它部位感觉不

适、出现红肿，请立即就医以免延误

治疗。

中文

4. 正确使用须知

English

Repetitive Stress Injury(RSI)

could occur.

If you feel discomfort, redness

and swelling of your fingers or

any other part of your body, see

a doctor before getting worse.

2. To avoid noise complaints, in

general, operate product

between 8a.m. and 5p.m. on

weekdays and 9a.m. to 5p.m.

weekends.

Check and follow the local

regulations as to sound level and

hours of operations for the product.

■ BEFORE STARTING THE

ENGINE

1. Operate the chain saw only in well

ventilated areas. Never start or run

the engine inside a closed room or

building. Exhaust fumes contain

dangerous carbon monoxide.

2. The area within a perimeter of 15

m of the person using the product

should be considered a hazardous

area into which no one should

enter. If necessary yellow warning

rope, warning signs should be

placed around the perimeter of the

area. When work is to be

performed simultaneously by two

or more persons, care should also

be taken to constantly look around

or otherwise check for the

presence and locations of other

people working so as to maintain a

distance between each person

sufficient to ensure safety.

3. Check the condition of working

area to avoid any accident by

hitting hidden obstacles such as

stumps, stones, cans, or broken

grass.

Remove any obstacle before

beginning work.

4. Inspect the entire unit for loose

fasteners and fuel leakage. Make

sure that the cutting attachment is

properly installed and securely

fastened.

5. Always use the shoulder strap.

Adjust the strap for comfort before

starting the engine. The strap

should be adjusted so the left

IMPORTANT

NOTE

4. Safety precautions

重要

补充

2. 为了避免工作噪音影响他人，操作

本产品的合适时间一般应为工作日的

上午 8 点至下午 5 点以及周末的上

午 9 点至下午 5 点。

关于噪音等级以及工作时间，请查询并

遵守当地的法规。

■启动引擎之前

1. 仅可在通风良好的区域操作链锯。切

勿在密闭的房间或建筑中启动或运行

本产品。因为链锯排出的废气中含有

有害的一氧化碳。

2. 以使用本产品的人员为圆心，15 米

为半径的圆周范围内为危险区域，严

禁他人进入。如有必要，应在该区域

周围放置黄色的警示绳索或警告标记。

当由两人或两人以上同时进行工作时，

应注意经常查看四周或检查其它工作

人员的工作位置，每位工作人员之间

应保留足够的距离以确保安全。

3. 检查工作区域的条件，以免由于意

外碰撞到诸如树桩、石块、罐头或碎

草等障碍物而导致意外事故。

在开始工作之前请清除所有障碍物。

4. 检查整个机器的紧固部件有无松动，

燃料是否有泄漏。务必确保切割装置

正确安装并牢牢紧固。

5. 请务必使用肩带。在启动引擎之前

调整肩带直至感觉舒适。肩带经调整

后应使长柄锯的把手高度约于腰齐，

以便左手持握。

中文

4. 正确使用须知

English

hand can comfortably hold the

handlebar grip approximately waist

high.

■ STARTING THE ENGINE

1. Keep bystanders and animals at

least 15 m away from the

operating point. If you are

approached, immediately stop the

engine.

2. The product is equipped with a

centrifugal clutch mechanism, so

the cutting attachment begins to

rotate as soon as the engine is

started by putting the throttle into

the start position. When starting

the engine, place the product onto

the ground in a flat clear area and

hold it firmly in place so as to

ensure that neither the cutting part

nor the throttle come into contact

with any obstacle when the engine

starts.

Never place the throttle into the

high speed position when starting

the engine.

3. After starting the engine, check to

make sure that the cutting

attachment stops rotating when

the throttle is moved fully back to

its original position. If it continues

to rotate even after the throttle has

been moved fully back, turn off the

engine and take the unit to your

authorized Zenoah servicing

dealer for repair.

■ USING THE PRODUCT

Cut only materials recommended

by the manufacturer. And use only

for tasks explained in the manual.

1. Grip the handles firmly with both

hands using your whole hand.

Place your feet slightly apart

(slightly further apart than the

width of your shoulders) so that

your weight is distributed evenly

across both legs, and always be

sure to maintain a steady, even

posture while working.

2. Maintain the speed of the engine

at the level required to perform

cutting work, and never raise the

IMPORTANT

WARNING

4. Safety precautions

重要

警告

中文

4. 正确使用须知

■启动引擎

1. 旁观者和动物等应远离操作点 15 米

以上。如果有人或动物靠近，应立即

关闭引擎。

2. 本产品配备有离心式离合器机构，

因此在启动引擎时只需将加油柄置于

启动位置，切割装置将立即开始旋转。

启动引擎时，请将本产品置于平坦干

净的场所，持握到位以确保引擎启动

时切割部件和加油柄不会接触到任何

障碍物。

启动引擎时切勿将加油柄置于高速位置。

3. 启动引擎后，请检查并确保当加油

柄完全回到初始位置时，切割装置停

止旋转。如果加油柄回到原位时切割

装置仍在旋转，则请关闭引擎并将本

产品送至经授权的 ZENOAH 维修服

务商处进行维修。

■使用本产品

仅切割制造商建议切割的材料。并仅用

于本手册中所述用途。

1. 请用双手的整个手掌紧握手柄。双腿

略微分开（略大于肩宽）以便均匀地

支撑体重。工作时请务必保持稳定、

平顺的姿势。

2. 将引擎的速度保持在执行切割工作

所需的等级，切勿使引擎速度超过所

需的等级。

English

speed of the engine above the

level necessary.

3. Never operate the pruner at an

angle greater than 60° in order to

reduce the risk of being struck by

falling objects during operation.

4. If the unit start to shake or vibrate,

turn off the engine and check the

whole unit. Do not use it until the

trouble has been properly

corrected.

5. Keep all parts of your body away

from rotating cutting attachment

and hot surfaces.

6. Never touch the muffler, spark

plug, or other metallic parts of the

engine while the engine is in

operation or immediately after

shutting down the engine. Doing

so could result in serious burns or

electrical shock.

• IF SOMEONE COMES

1. Guard against hazardous

situations at all times. Warn adults

to keep pets and children away

from the area. Be careful if you are

approached. Injury may result from

flying debris.

2. If someone calls out or otherwise

interrupts you while working,

always be sure to turn off the

engine before turning around.

■ MAINTENANCE

1. In order to maintain your product

in proper working order, perform

the maintenance and checking

operations described in the

manual at regular intervals.

2. Always be sure to turn off the

engine before performing any

maintenance or checking

procedures.

(1) Check ok !

The metallic parts reach high

temperatures immediately after

stopping the engine.

3. When replacing the cutting

attachment or any other part, or

when replacing the oil or any

lubricant, always be sure to use

only ZENOAH products or

products which have been

certified by ZENOAH for use

with the ZENOAH product.

WARNING

4. Safety precautions

警告

中文

4. 正确使用须知

3. 切勿以超过 60 度的角度操作修枝剪，

以避免操作时被坠物砸到的危险。

4. 如果本机开始抖动或振动，请关闭

引擎并检查整个机器。在故障被正确

排除之前请勿使用。

5. 请使您身体的所有部位远离旋转的

切割装置和灼热的切割表面。

6. 在引擎运行时或关闭引擎后的瞬间，

切勿触碰消音器、火花塞或引擎的其

它金属部件。否则可能导致严重的灼

伤或触电。

●如果有人进入工作区域

1. 请随时警惕是否有危险情况发生。警

告成人将宠物与儿童带离工作区域。

请注意，如果有人靠近，飞溅的碎屑

可能导致人身伤害。

2. 如果有人在您工作时召唤或打断您，

请务必在转身之前先关闭引擎。

■检修

1. 为了保证您的产品正确工作，请定期

执行本手册中所述的检修和检查操作。

2. 在执行任何检修或检查步骤之前，

请务必先关闭引擎。

（1）可以检查！

停止引擎后金属部件将立即升温。

3. 当更换切割装置或任何其它部件时，

或更换燃油或润滑油时，请务必仅使

用 ZENOAH 产品或经 ZENOAH 认

证可用于 ZENOAH 的产品。

English

4. Safety precautions

4. In the event that any part must be

replaced or any maintenance or

repair work not described in this

manual must be performed, please

contact a representative from the

store nearest ZENOAH authorized

servicing dealer for assistance.

5. Do not use any accessory or

attachment other than those

bearing the ZENOAH mark and

recommended for the unit.

6. Under no circumstances should

you ever take apart the product or

alter it in any way. Doing so might

result in the product becoming

damaged during operation or the

product becoming unable to

operate properly.

■ HANDLING FUEL

1. The engine of the ZENOAH

product is designed to run on a

mixed fuel which contains highly

flammable gasoline. Never store

cans of fuel or refill the tank of the

unit in any place where there is a

boiler, stove, wood fire, electrical

sparks, welding sparks, or any

other source of heat or fire which

might ignite the fuel.

2. Never smoke while operating the

unit or refilling its fuel tank.

3. When refilling the tank, always

turn off the engine and allow it to

cool down. Take a careful look

around to make sure that there are

no sparks or open flames

anywhere nearby before refueling.

(1) Refill after cooling the engine.

4. Wipe spilled fuel completely using

a dry rag if any fuel spillage occurs

during refueling.

5. After refueling, screw the fuel cap

back tightly onto the fuel tank and

then carry the unit to a spot 10 feet

or more away from where it was

refueled before turning on the

engine.

■ TRANSPORTATION

1. When you finish cutting in one

location and wish to continue work

in another spot, turn off the

engine, lift up the unit and carry it

paying attention to the blade.

2. Never forget to place the

protective cover over the blades.

3. When transporting the unit over

long distances, detach the blade

中文

4. 正确使用须知

4. 如需更换部件，或执行本手册中未

加以说明的检修或维修工作时，则请

与最近的 ZENOAH 授权的维修服务

商代表联系以获取帮助。

5. 请勿使用未带有 ZENOAH 标记和

被推荐的产品以外的其它附件或装置。

6. 在任何情况下都不得以任何方式拆

解本产品或对其进行改装。否则可能

导致产品在操作中受损或导致产品无

法正常工作。

■关于燃料

1. ZENOAH 产品的引擎可使用含有高

易燃性汽油的混合燃料。切勿在有锅

炉、加热器、柴火、电火花、焊接火

花的场所或其它可能点燃燃料的热源

或火源处存放罐装燃料或为机器加油。

2. 操作机器或加油时切勿抽烟。

3. 在加油时，请务必先关闭引擎并使

其冷却。在加油之前仔细检查四周，

确保附近没有火花或明火。

（1）冷却引擎后加油。

4. 如果加油时有任何溢出情况发生，

请用干抹布将溢出的燃料完全擦干。

5. 加油之后，请将燃料箱上的燃料盖

拧紧。然后将机器移至距离加油点

3m 以上的位置再启动引擎。

■运输

1. 切勿在引擎运转的情况下运送修枝剪

或将其置于某处。正在运转的引擎可

能会意外加速导致链条旋转。

2. 运送修枝剪时请确保鞘处于正确位

置。

3. 手持机器时，链条应朝向后面。

and fix the unit by ropes.

4. Never transport the product over

rough roads over long distances

by vehicle without removing all fuel

from the fuel tank. If doing so, fuel

might leak from the tank during

transport.

■ Kickback and Pinching Safety

Precautions

Beware of kickback!

Kickback can occur whenever the tip

of the guide bar touches an object

while the saw is operating. Kickback

may force the bar up and back

toward the operator with lightning-like

speed!

Beware of pinching.

Pinching the saw along the tip of the

guide bar may force the bar back

rapidly toward the operator. Pinching

can occur whenever wood closes in

around the moving chain.

Both kickback and pinching may

cause you to lose control of the

pole pruner which could result in

serious personal injury. Do not

rely exclusively on the safety

device built into the pruner! You

must take several steps to keep

your jobs free from accident or

injury:

1. Understand kickback and

pinching! You can reduce or

eliminate the element of surprise.

Sudden surprises contributes to

accidents.

2. Keep a firm grip on the pole pruner

with both hands whenever the

engine is running. A firm grip will

help you reduce the affects of

kickback and pinching as well as

maintain control of the machine.

3. Make sure the area in which you

are cutting is free from

obstructions. Do not let the nose of

the guide bar contact a log,

branch, or any other obstructions

which could be hit while you

operation the pole pruner.

4. Cut at high engine speeds.

5. Follow the manufacturer's

instructions for sharpening and

maintaining the chain.

6. Use only the replacement bar and

chain or equivalent as specified by

WARNING

English

4. Safety precautions

警告

中文

4. 正确使用须知

4. 切勿在燃料箱中尚存燃料的情况下

使用车辆在长距离粗糙路面上运输本

产品。否则燃料可能会在运输时从燃

料箱中泄漏。

■有关反弹和卡滞的安全注意事项

小心反弹！

电锯运转时，如果导向条的顶端触碰到

了物体，则会发生反弹。反弹可能会使

导向条以闪电般的速度往上或往后弹向

操作者。

小心卡滞。

锯片沿着导向条顶端被卡住，可能会使

导向条快速向后弹向操作者。当木料夹

住运行的链条时会发生卡滞现象。

反弹和卡滞都会导致长柄修枝剪失控，

从而可能导致严重的人身伤害。请勿完

全依赖于修枝剪中内置的安全装置！你

必须做到以下几点以避免发生意外或伤

害事故：

1. 了解什么是反弹和卡滞！这样可以减

少或消除发生反弹和卡滞时的恐慌。

这种突然的恐慌只会增加事故伤害的

几率。

2. 引擎运转时请务必用双手牢牢紧握

长柄修枝剪。此举有助于减少反弹和

卡滞的影响，并可确保对机器的有效

控制。

3. 请务必确保您进行切割的区域没有

障碍物。请勿让导向条的前端接触到

木头、树枝或其它可能在操作长柄修

枝剪时碰到的障碍物。

4. 以较高的引擎速度进行切割。

5. 打磨和保养链条时请遵照制造商的

说明。

6. 请仅使用制造商指定的备用导向条

和链条或同等产品。

English

4. Safety precautions

the manufacturer.

• Make sure the chain and

sprocket are correctly adjusted

before operating the pruner (see

page 14, 15 for adjustment

procedures). Never attempt

chain adjustment with the

engine running!

• Always make sure the cutting

attachment is properly installed

and firmly tightened before

operation.

• Never use a cracked or warped

guide bar: replace it with a

serviceable one and make sure

it fits properly.

• If a saw blade should bind fast

in a cut, shut off the engine

immediately. Push the branch or

tree to ease the bind and free

the blade.

• Do not operate the pole pruner

with the muffler removed.

• When cutting a limb that is

under tension, be alert for

springback so that you will not

be struck by the moving limb.

• Always stop the engine

immediately and check for

damage if you strike a foreign

object or if the machine

becomes tangled. Do not

operate with broken or damaged

equipment.

• Do not make unauthorized

modifications or substitutions to

the guide bar or chain.

• Never allow the engine to run at

high RPM without a load. Doing so

could damage the engine.

• Keep the pruner as clean as

possible. Keep it free of loose

vegetation, mud, etc.

IMPORTANT

WARNING

重要

警告

中文

4. 正确使用须知

・在操作修枝剪之前请确保链条和链齿

已正确调整（有关调整步骤请参见第

14及15页）。切勿在引擎运行时进行

链条调整！

・在操作之前请务必确保切割装置已正

确安装并紧固。

・请勿使用有裂缝或弯曲的导向条。若

出现这种情况，请更换为可用的导向

条并确保安装到位。

・如果在切割中锯片被卡住，则应立即

关闭引擎。取下卡住锯片的树枝或树

木以释放锯片。

・请勿在消音器被拆除的情况下操作长

柄修枝剪。

・当切割处于张力之下的枝干时，请小

心避免被反弹的枝干打到。

・如果碰到异物或机器被异物缠绕，请

务必立即停止引擎并检查是否有损坏。

请勿使用破损或损坏的装置继续操作。

・未经授权，请勿对导向条进行的改动

或替换。

・不得使引擎在无负荷的情况下高速运

行。否则可能会损坏引擎。

・请尽可能地保持修枝剪清洁。避免将

其应用于有散乱的植被或泥泞等物的

场所。

English

5. Set up

■ MOUNTING ENGINE (SE1)

1. Push the driveshaft housing

toward the clutch housing and

rotate it by hand to check that the

driveshaft is engaged with the

gears.

2. Insert the driveshaft housing into

the clutch housing until it bottoms,

and align the positioning holes on

the both housings and install the

screw.

3. Fasten the clamp securely with 2

screws.

■ CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle

wire to the joint on the top of the

carburetor. (SE2)

■ CONNECTING SWITCH WIRES

(SE3)

• Connect the switch wires between

the engine and the main unit.

• Fix the switch wire like figure of

SE3.

• The space between a tank and

switch wires is 3mm or more.

(1) 3mm or more

■ INSTALLING HANDLE (SE4)

• Install the handle to the shaft tube

and clamp it at a location that is

comfortable to you.

(1) About 48cm

■ JOINT ATTACHMENT (SE5)

• Insert the attachment to the main

shaft.

• Tighten the knob bolt securely.

(1) Knob bolt

SE1

SE2

SE3

SE4

(1)

SE5

中文

■安装引擎（SE1）

1. 将驱动轴罩推向离合器罩，并用手旋

转以检查驱动轴是否与齿轮啮合。

2. 将驱动轴罩插入离合器罩直至底部，

然后使两个罩上的定位孔对齐，装上

螺钉。

3. 用2个螺钉紧固夹具。

■连接加油线

1. 拆下空气滤清器的盖子。

2. 将加油线的一端连接至化油器顶部

的接头上。（SE2）

■连接开关线（SE3）

・连接引擎和主机之间的开关线。

・如图SE3所示固定开关线。

・燃料箱和开关线之间的距离应为

3mm或以上。

（1）3mm或以上

■安装把手（SE4）

・将把手安装到轴管并夹紧在您觉得适

合的位置。

（1）约48cm

■接头连接（SE5）

・将接头插入主轴。

・坚固旋钮螺栓。

（1）旋钮螺栓

5 安装

English

5. Set up

■ ATTACHING THE PRUNING

MECHANISM (SE6)

1. Remove the cap on the end of the

main pipe.

2. Remove the screw screwed into

the end of the gear case.

3. Insert the end of the gear case into

the main pipe.

4. Line up the hole on the end of the

gear case into which the screw is

to be inserted with the hole on the

main pipe, and screw the screw

firmly in.

5. Using a wrench, screw in the bolt

provided to fix the mechanism into

place.

(1) Main pipe (2) Gear case

(3) Screw hole (4)Fastening bolt

(5) Bolt

A standard package contains the

items as shown below. (SE7)

(1) Guide bar (2) Saw chain

(3) Gear case (4) Sprocket

(5) Chain tension adjust screw

(6)

Nut

(7)

Chain tensioner nut

(8) Chain

cover

Install the guide bar and the saw

chain on the gear case as follows.

The saw chain has very sharp

edges. Use protective gloves for

safety.

1. Loosen a nut and remove the

chain cover.

2. Mount the guide bar then fit the

saw chain around the bar and

sprocket.(SE8)

Pay attention to the correct

direction of the saw chain

WARNING

SE8

SE7

(1)

(2)

(3)

(4)

(5)

SE6

警告

中文

■安装修枝机构（SE6）

1. 拆下主管末端的盖子。

2. 拆下拧在齿轮箱末端的螺钉。

3. 将齿轮箱的末端插入主管中。

4. 将齿轮箱上的螺丝孔与主管上的螺

丝孔对齐，插入螺钉然后拧紧。

5. 使用扳手拧紧随附的螺栓以将修枝

机构固定到位。

（1）主管

（2）齿轮箱

（3）螺丝孔

（4）紧固螺栓

（5）螺栓

标准零件包中包含以下所示零件。

（SE7）

（1）导板

（2）锯链

（3）齿轮箱

（4）链齿

（5）链条张力调节螺钉

（6）螺母

（7）链条张紧螺母

（8）链条盖

如下所示将导板和锯链安装到齿轮箱。

锯链的边缘非常锋利。请佩戴防护手套

以策安全。

1. 拧松螺母并拆下链条盖。

2. 安装导板，然后将绕着导板和链齿

安装锯链。（SE8）

请注意锯链的正确方向

5 安装

English

5. Set up

SE9

SE11

SE10

3. Fit the chain tensioner nut into the

lower hole of the guide bar, then

install the chain cover, and fasten

the mounting nut to finger

tightness. (SE8) (SE9)

(1) Hole

(2) Moving direction

(3) Chain tensioner nut

4. Adjust the chain tension by turning

the tensioner screw until the tie

straps just touch the bottom side

of the bar rail. (SE10)

(1) Chain tension adjusting screw

(a) Loosen

(b) Tighten

5. Tighten the mounting nut securely

with the bar tip held up (SE11)

(TORQUE: 8.9~11.7 N.m./90~120

kg-cm). Then check the chain for

smooth rotation and correct

tension while moving it by hand. If

necessary, readjustment.

(1) Tighten

It is very important to maintain the

proper chain tension. Rapid wear

of the guide bar or the chain

coming off easily can be caused

by improper tension. Especially

when using a new chain, take

good care of it since it should

expand when first used.

■ BALANCE UNIT

1. Put on strap and attach unit to

strap.

2. Depending on the working

posture, slide clamp up or down

until unit balances and the strap

fits your body.

WARNING

警告

中文

3. 将链条张紧螺母装到导板下部的孔

中，然后安装链条盖，并将安装螺母

拧紧至手指无法拧松的程度。

（SE8）（SE9）

（1）孔

（2）运动方向

（3）链条张紧螺母

4. 通过转动张紧螺钉调节链条张力，

直至系带正好碰到板轨的底部。

（SE10）

（1）链条张力调节螺钉

（a）拧松

（b）拧紧

5. 握住导板顶端，紧固安装螺母。

（SE11）

（扭矩：8.9_11.7N.m./90_120kg-

cm）然后用手移动链条，检查链条

是否平滑旋转，张力是否合适。如果

必要请重新调节。

（1）拧紧

保持链条的张力正确非常重要。如果张

力不正确，很容易导致导板的快速磨损

或链条脱落。尤其是使用新链条时，请

特别小心，初次使用时链条会扩张开来。

■机器的平衡

1. 穿戴好肩带，然后将机器安装到肩带

上。

2. 根据工作时采用的姿势，向上或向

下滑动肩带直至机器保持平衡，并使

肩带贴合您的身体。

5 安装

•Gasoline is very flammable.

Avoid smoking or bringing any

flame or sparks near fuel.

• Wipe up all spills before

starting the engine.

•Make sure to stop the engine

and allow it cool before

refueling the unit.

• Keep open flames away from

the area where fuel is handled

or stored.

•Never use oil for 4 cycle engine

use or water cooled 2-cycle

engine.

• Never use "FUEL WITH NO OIL

(RAW GASOLINE)".

• Never use fuel laced with water.

• Mixed fuels which have been left

unused for a period of one month

or more may clog the carburetor

or result in the engine failing to

operate properly. Put remained

fuel into an air-tight container and

keep it in the dark and cool room.

• Please ask for “mixed gasoline for

air-cooled 2-cycle engines” at your

nearest gas station, or use fuel

made by putting unleaded

gasoline for automobiles and air-

cooled 2-cycle engine oil into a

mixing container in accordance

with the following ratios and then

shaking to mix well.

Mixing ratios:

When using Zenoah genuine 2-cycle

oil (FC grade):

50:1 (100 ml of oil for

every 5 liters of gasoline)

When using commercially available

2-cycle oil (FB grade):

25:1(160 ml of oil for

every 4 liters of gasoline)

■ CHAIN OIL

Use motor oil SAE #10W-30 all year

round or SAE #30 ~ #40 in summer

and SAE #20 in winter.

Do not use wasted or regenerated oil

that can cause damage to the oil

pump.

NOTE

IMPORTANT

WARNING

English

6. Fuel and chain oil

重要

补充

警告

中文

・汽油为易燃品

不得在燃料附近吸烟或玩弄带有火焰

和火星物。

・在启动引擎之前整理好周围的散乱物

品。

・在加油之前必须确认引擎停止并冷却。

・在加油和储油地区必须严禁烟火。

・不能使用4冲程机油，或水冷2冲程

引擎机油。

・不能使用未与机油混合的燃料（普通

汽油）。

・不能使用混入水的燃料。

・一个月以上没有使用过的混合燃料有

可能妨碍化油器工作，或者引起引擎

工作不良。请把剩下的燃料装在密闭

容器内，并放置在阴凉爽处。

・燃料可使用在附近加油站购买的气冷

2冲程引擎用混合汽油，或者将汽车

用无铅汽油和气冷2冲程引擎机油按

以下比例倒入同一容器，好好摇晃容

器，混合配制的燃料。

混合比例：

如使用Zenoah 2冲程纯正机油(FC级):

50:1（汽油5L：机油100ml）

如使用市面销售的2冲程机油(FB级):

25:1（汽油4L：机油160ml）

■链条油

使用电动机润滑油SAE # 10W-30（整

年使用），或SAE #30－#40（夏天使

用）和SAE #20（冬天使用）。

请勿使用报废或再生的机油，这类机油

会致使油泵损坏。

6. 燃料和链条油

English

7. Operation

■ STARTING ENGINE

The cutting head will start rotating

upon the engine starts.

1. Feed fuel and chain oil into their

respective tanks and tighten the

caps securely. (OP1)

(1) Fuel

(2) Chain oil

2. Rest the unit on a flat, firm place.

Keep the cutting head off the

ground and clear of surrounding

objects as it will start rotating upon

starting of the engine.

3. Push the pump several times until

overflown fuel flows out in the

clear tube. (OP2)

4. Move the choke lever to the closed

position. (OP3)

(1) Choke lever

(2) Close

(3) Open

5. Set the stop switch to the "RUN"

position.

Place the unit on a flat place.

Keep the cutting head clear of

everything around it. (OP4)

(1) Stop switch

6. While holding the unit firmly, pull

out the starter rope quickly until

engine fires. (OP5)

• Avoid pulling the rope to its end or

returning it by releasing the knob.

Such actions can cause starter

failures.

7. Move the choke lever downward to

open the choke. And restart the

engine. (OP3)

8. Allow the engine to warm up for a

several minutes before starting

operation.

IMPORTANT

WARNING

OP2

OP1

OP3

(1)

OP4

OP5

重要

警告

中文

■启动引擎

引擎启动时切割头将开始旋转。

1. 将燃料和链条油分别加入各自的油箱

中，然后牢牢地拧紧油箱盖子。

（OP1）

（1）燃料

（2）链条油

2. 将机器放置在平坦、坚固的地方。

由于引擎启动时切割头将开始旋转。

因此请使其指向地面并保持周围没有

异物。

3. 推泵数次，直至清洁的管子中溢出

燃料。（OP2）

4. 将进气杆移至关闭位置。（OP3）

（1）进气杆

（2）关闭

（3）开通

5. 将止动开关设至“RUN（运行）”

位置。

将机器放置在平坦、坚固的地方。

保持切割头周围没有任何异物。

（OP4）

（1）止动开关

6. 紧握住机器，快速抽拉起动器的拉

绳直至引擎着火。（OP5）

・避免将拉绳拉到底或通过松开旋钮使

其返回。否则会导致起动器失败。

7. 向下操作进气杆以开通进气门。然

后重新启动引擎。（OP3）

8. 在开始操作之前请先让引擎预热几

分钟。

7. 操作

English

7. Operation

1. When restarting the engine

immediately after stopping it, leave

the choke open.

2. Overchoking can make the engine

hard to start due to excess fuel.

When the engine failed to start

after several attempts, open the

choke and repeat pulling the rope,

or remove the spark plug and dry

it.

■ STOPPING ENGINE (OP4)

1. Release the throttle lever and run

the engine for a half minute.

2. Shift the stop switch to the “Stop”

position. (OP4)

• Except for an emergency, avoid

stopping the engine while pulling

the throttle lever.

■ CHECKING OIL SUPPLY

• After starting the engine, run the

chain at medium speed and see if

chain oil is scattered off as shown

in the figure. (OP6)

(1) Chain oil

The oil reservoir has a capacity

sufficient to provide about 40 minutes

of cutting time (when set to deliver

the minimum flow rate, or about as

long as you'll get from a tank of fuel).

Be sure to refill the oil tank every

time when refueling the saw.

■ ADJUSTING OIL FLOW RATE

Never fill the oil reservoir nor

adjust the oiler with the engine

running.

An increase in bar oil flow rate will

speed oil consumption, requiring

more frequent checks on the oil

reservoir. To ensure sufficient

lubrication, It may be necessary to

IMPORTANT

WARNING

NOTE

IMPORTANT

NOTE

OP6

重要

补充

警告

中文

1. 当停止引擎后立即重新启动时，进气

门仍然开通。

2. 当进气量过大时，由于燃料过量，

会使引擎难以启动。当多次启动引擎

失败时，请开通进气门并重复抽拉拉

绳，或拆下火星塞使其干燥。

■停止引擎（OP4）

1. 松开加油杆并让引擎运转半分钟。

2. 将止动开关切换至“Stop（停

止）”位置。（OP4）

・除了紧急情况之外，请避免在拉加油

杆时停止引擎。

■检查机油供给情况

・启动引擎之后，以中速运行链条并查

看链条油是否如图所示分散开来。

（OP6）

（1）链条油

储油箱有足够的容量可提供约40分钟

的切割时间内所需的链条油（当设为最

小）。每次为链锯加油时请务必也在油

箱中加油。

■调节机油流量

切勿在引擎运转时进行加油或调节油壶。

机油流量的增加会加速机油消耗，需要

更频繁地检查储油箱。为确保有充足的

润滑油，可能需要比燃料箱加油时更为

频繁地检查机油量。

7. 操作

English

7. Operation

check the oil level more frequently

than at fuel tank refills.

The guide bar and chain are

lubricated automatically by a pump

that operates whenever the chain

rotates. The pump is set at the

factory to deliver a minimum flow

rate, but it can be adjusted in the

field. A temporary increase in oil flow

is often desirable when cutting things

like hardwood or wood with a lot of

pitch.

Adjust the pump as follows:

1. Stop the engine and make sure

the stop switch is in the STOP

position.

2. Place the unit on its side with the

oil reservoir up. (OP7)

(1) Oil tank

(2) Chain cover

The oil flow adjusting screw must be

pressed in slightly in order to turn.

Failure to do so could damage the

pump and screw.

3. With a screwdriver, push in on the

oil flow rate adjusting screw and

turn in the desired direction (there

are three incremental settings):

(a) Clockwise-decrease

lubrication.

(b) Counter clockwise-increase

lubrication.

■ ADJUSTING THROTTLE CABLE

• The normal play is 1 or 2mm when

measured at the carburetor side

end. Readjust with the cable

adjuster as required. (OP8)

(1) Cable adjuster

IMPORTANT

.04 in

(1~2mm)

(1)

OP8

OP7

重要

中文

导板和锯链通过锯链旋转时运转的泵自

动进行润滑。该泵在出厂时设定一个最

低流量，但在实际操作中可进行调节。

当切割硬木或有很多树脂的木头等材料

时经常需要临时增大机油流量。

如下所述调节泵：

1. 停止引擎，并确保止动开关处于

STOP（停止）位置。

2. 将机器侧放，使储油箱朝上。

（OP7）

（1）油箱

（2）链条盖

必须轻轻地按下机油流量调节螺钉以使

其转动。否则可能会损坏泵和螺钉。

3. 使用螺丝刀，推入机油流量调节螺

钉并以所需方向旋转（有三种增量设

定）：

（a）顺时针转动螺钉以减少润滑油。

（b）逆时针转动螺钉以增加润滑油。

（c）中间

■调节加油钢丝

・在化油器侧进行测量时，钢丝的正常

行程应为1或2mm。需要时可通过钢

丝调节器重新进行调节。（OP8）

（1）钢丝调节器

7. 操作

English

7. Operation

■ ADJUSTING IDLING SPEED

(OP9)

1. When the engine tends stop

frequently at idling mode, turn the

adjusting screw clockwise.

2. When the cutting head keeps

rotating after releasing the trigger,

turn the adjusting screw counter-

clockwise.

(1) Idle adjusting screw

• Warm up the engine before

adjusting the idling speed.

•Always wear work gloves made

of leather or some other sturdy

material when using the

polesaw.

• Falling branches may fall onto

the face or into the eyes,

resulting in injuries, scratches,

and cuts, and for this reason

you should always be sure to

wear a helmet and face

protector when using your

polesaw.

WARNING

NOTE

OP9

补充

警告

中文

■调节空转速度（OP9）

1. 如果在空转模式中引擎经常趋于停止，

请顺时针转动调节螺钉。

2. 如果在释放扳机之后切割头仍然旋

转，则请逆时针转动调节螺钉。

（1）空转调节螺钉

・在调节空转速度之前请先预热引擎。

・使用长柄锯时请务必佩戴由皮革或其

它坚固的材料制成的工作手套。

・掉落的分枝可能会落到操作者的脸上

或眼睛里，从而导致受伤、刮伤和切

口。因此当使用长柄锯时请务必穿戴

头盔和面罩。

7. 操作

ページが読み込まれています...

Zenoah Pole Saw PSJ2300 ユーザーマニュアル

ブランド: Zenoah

モデル: Pole Saw PSJ2300

カテゴリー: おもちゃ

タイプ: ユーザーマニュアル

このマニュアルも適しています

PSJ2300

PDFをダウンロードします

報告

他の言語で

English: Zenoah Pole Saw PSJ2300 User manual

Zenoah Pole Saw PSJ2300 ユーザーマニュアル

このマニュアルも適しています

Zenoah Pole Saw PSJ2300 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント