Braven Ready SOLO ユーザーマニュアル

タイプ
ユーザーマニュアル

このマニュアルも適しています

USER GUIDE
ENGLISH | 2
GET TO KNOW YOUR BRAVEN
POWER ON / OFF
PLAY / PAUSE
BLUETOOTH PAIRING
ANSWER / END CALL /
VOICE CONTROL
I/O PORT COVER
(Seal tightly for waterproofing)
VOLUME DOWN,
SKIP BACK
(press and hold)
M I C R O - U S B
CHARGING PORT
V O L U M E U P ,
SKIP TRACK
(press and hold)
3 . 5 M M
AUDIO-IN JACK
EXTERNAL USB
CHARGING PORT
RESET BUTTON
BATTERY CHECK BUTTON
ENGLISH | 3
POWER & BLUETOOTH PAIRING
CHARGING YOUR BRAVEN
1. Press the Power button for 2-3 seconds to turn your BRAVEN READY SOLO™ on or off.
2. Activate / enable Bluetooth
®
on your device’s settings.
3. Speaker automatically enters pairing mode upon powering on. To pair a second
device, press and hold the Bluetooth button. Go to your phone or device’s
Bluetooth
®
settings and select “BRAVEN READY SOLO” from the list.
4. Enter “0000” if asked for a pass code.
Your BRAVEN will remember the last 8 devices it has paired with.
NOTE: If your BRAVEN does not have an active Bluetooth
®
connection and is left on, it automatically powers off
after 30 minutes. To restart your BRAVEN you will need to press and hold the power button for 2-3 seconds.
Before using your BRAVEN for the first time, charge the unit until the battery indicator light turns off.
To charge your BRAVEN, plug the included Micro-USB cable into a wall power adapter (not included) or into a
powered USB port on a computer. Plug the Micro-USB connector end of the cable into the BRAVEN charging port.
Once fully charged, your BRAVEN READY SOLO
has 12 hours of playtime at medium volume.
ENGLISH | 4
CHARGING EXTERNAL DEVICES
SPEAKERPHONE
Your BRAVEN is designed to charge USB devices that draw from 0.3A - 1A using the full-sized USB port located
behind the I/O port cover. To use external charging:
1. Turn your BRAVEN on.
2. Plug the Micro USB power cable that came with your phone, mp3 player,
or other mobile device into the USB port on your BRAVEN.
3. Plug the other end of the cable into your mobile device, and it will immediately begin charging.
Press the Mic button button on your BRAVEN to answer the call over the speaker. Press the Play / Pause Mic
button again to end the call.
WATERPROOF FEATURES
The BRAVEN READY SOLO
is IP68 waterproof, and is designed to withstand rainfall, waterjets, water
splashing, or a dunk in the pool.
IMPORTANT: To ensure your BRAVEN READY SOLO
speaker is prepared for use in a wet environment, remove
all cable connections and tightly close the I/O port cover on the back of the speaker. If this cover is not
securely fastened to the speaker, BRAVEN READY SOLO
will not be waterproof.
USING BRAVEN VOICE CONTROL
To activate Siri or Google Commands with your BRAVEN, short press the Mic button. You can now say commands
through your BRAVEN, with your phone at a distance.
ENGLISH | 5
USING TRUEWIRELESS STEREO
PAIRING
RESETTING YOUR BRAVEN
USING THE ACTION MOUNT
TrueWireless allows you to wirelessly pair two BRAVEN READY SOLO
speakers in right & left channel audio.
To activate TrueWireless, long press the “battery check button” on the back of both speakers at the same time
until a pairing chime emits. Within 30 seconds, a beep will indicate that both speaker have successfully paired.
To reset your BRAVEN READY SOLO
to factory settings, press the Reset button located on the back of your speaker.
The included Action Mount allows you to attach your BRAVEN READY SOLO to most GoPro™ mounting systems. To
attach the Action Mount to the READY SOLO, align the mount with the holes on the bottom of your BRAVEN. Secure
the mount using the included screws and hex wrench.
ENGLISH | 6
WARNINGS, CAUTION
& LEGAL INFORMATION
To reduce the risk of fire or electric shock, do not expose
the BRAVEN to rain or moisture while charging. The
BRAVEN should not be exposed to dripping or splashing,
and objects filled with liquids, such as vases, should not
be placed on or near it while being charged or charging
other devices. As with any electronic products, use care
not to spill liquids into any part of the product. Liquids
can cause a failure and/or a fire hazard. The power supply
must be used indoors only. Make no modifications to the
product or accessories. Unauthorized alterations may
compromise safety, regulatory compliance, and system
performance, and will void the warranty. Do not place
any flame sources, such as lighted candles, on or near
the BRAVEN. The BRAVEN contains small parts that
may be a choking hazard and is not suitable for children
under age 3. Do not continue charging the battery if it
does not reach full charge within the specified charging
time. Overcharging may cause the battery to become hot,
rupture, or ignite. If you see any heat deformation or
leakage, properly dispose of the battery. Do not attempt
to charge the battery in temperatures outside the range
of 32°-104°F (0°-40°C). If the battery begins to leak, do
not allow the liquid to come in contact with your skin
or eyes. If contact has been made, wash the affected
area with plenty of water and seek medical attention
immediately. Do not expose the product or battery to
excessive heat, including direct sunlight or fire and
storage or use inside cars in hot weather, where it can be
exposed to temperatures in excess of 115°F (60°C). Doing
so may cause the battery and power supply to generate
heat, rupture, or ignite. Using the product in this manner
also may result in a loss of performance and a shortened
life expectancy. Extended exposure to direct sunlight
may damage the external appearance and material
qualities. Do not step on, throw, or drop batteries or
the power supply or device, or expose them to a strong
shock. Do not pierce, crush, dent, or deform the batteries
or power supply in any way. If either becomes deformed,
properly dispose of it. Do not short-circuit batteries. Do
not attempt to service the BRAVEN yourself. Opening or
removing covers may expose you to dangerous voltages
or other hazards and will void the manufacturer’s
warranty. To prevent risk of fire or electric shock, avoid
overloading wall outlets, extension cords, or integral
convenience receptacles. Your Bluetooth device (mobile
phone, music player, tablet, laptop, etc.) must support
the A2DP Bluetooth profile in order to work wirelessly
with your new BRAVEN speaker. The A2DP profile is
supported by most recent mobile products with built-
in Bluetooth capability. Please refer to your device’s
user manual for details and instruction regarding the
Bluetooth profiles it supports. This device complies with
part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:—Reorient or relocate the
receiving antenna. —Increase the separation between
the equipment and receiver. Connect the equipment
into an outlet on a circuit different from that to which
the receiver is connected. — Consult the dealer or an
experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
FCC RADIATION EXPOSURE STATEMENT: This device
complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device. Under Industry Canada
regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Lithium Battery installed is not intended to be replaced
by the USER.
CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
Where the MAINS plug is used as the disconnect device,
the disconnect device shall remain readily operable.
The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
Correct Disposal of this product. This marking
indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent
possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
To return your used device, please use the return and
collection systems or contact the retailer where the
product was purchased.
This product complies with California Energy
Commission efficiency standards for consumer battery
chargers.
Hereby, Braven, declares that this device is in
compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU
Operating Frequency Band: 2402 MHz to 2480 MHz
Maximum RF power: 6dBm EIRP
Braven hereby declares that READY SOLO is in compliance
with Radio Equipment Directive 2014/53/EU.The full text
of the EU DoC is available at the following: https://www.
braven.com/eu-declaration-of-conformity/*****.PDF
Braven follows Safety Instruction for CE-LV. Operate
Products not more than -5~40 °C.
Do not install this equipment in a confined or building-in
space such as a book case or similar unit, and remain a
well ventilation conditions. The ventilation should not be
impeded by covering the ventilation openings with items
such as newspaper, table-cloths, curtains etc.
WARNING:To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture. The
apparatus shall not be exposed to dripping or splashing
and that objects filled with liquids, such as vases, shall
not be placed on apparatus.
WARNING: The power adapter is used as disconnect
device, the disconnect device shall remain readily
operable.
WARNING:Please refer the information on exterior
bottom enclosure for electrical and safety information
before installing or operating the apparatus.
CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
The battery (battery or batteries of battery pack) shall
not be exposed to excessive heat such as sunshine, fire
or the like.
Article 10
2. Manufacturers shall ensure that radio equipment
shall be so constructed that it can be operated in at
least one Member State without infringing applicable
requirements on the use of radio spectrum.
10. In cases of restrictions on putting into service
or of requirements for authorisation of use,
information available on the packaging shall allow
the identification of the Member States or the
geographical area within a Member State where
restrictions on putting into service or requirements
for authorization of use exist. Such information
shall be completed in the instructions accompanying
the radio equipment. The Commission may adopt
implementing acts specifying how to present that
information. Those implementing acts shall be
adopted in accordance with the advisory procedure
referred to in Article 45(2).
Manufacturer: Braven LC.
󵶎󰽥󰶦󳛒 | 7
󴦠󴧅󲼭󹄶󱙭󹀺󴕿󱋎󹄶󰶦
󹄎󴘫󴉢
 󴊐󴛹󹑳󴍂
󶰄󵇕󴓊
󰽥󴘬󴶠󰽥󱋎󹄶󰶦󱋎󹄶󰶦
󰵴󸑛󶔨
󰺮󹄶󲒩󷢢󱡸󱝛󳸬󷢢󱡸󸛈󱐔
󴓊󰽥󴎤 󲼑
 󴓊󰽥󳙧󹁻󴦠󴧅󱙭󹀺󲮸󸁰
󱜴󶡊󲶎 󹄶󴙂󲚋󱌼
󰾫󵈾󲳴󷦳 󷢢󱡸󰺱󲚪
󱡸󳙖 󸔢 󷫪󱜴
󳙖 󸔢 󲔝 󱌌 󲶎 󴎁 󰻁 󹌬 󲔛   
󲶎󶡊󳐧󱜴󶡊󲶎󱁃󷫿󴬁
󱔭  󳟈  󴧧
󴙂󰵴󸑛󶔨

󰶺󰸫󱎸󲘱󴦠󴧇󳃵󷩘󵉐󵒹󱙭󹀘󼵼󷸽󱖢󱲉󱋎󵉐
󳞟󲘜󳣑󹆫󱲉󹄎󰶦󳃵󴟑󴘫󴾡󱺯󰶦
󰵷󲪿󳣑󹆫󰸶󴛹󴊐󳃵󹑸󴘲󼵼󱋎󴛙󴓊
󰽥󵒹󴶠󱡸󼵸󲁵󶰄󵇕󼵹󰵷󲪿󳙞󶔨󱲉󱌧󰵴󳃵󸿢
󸑛󼵼󱝛󳞟󲘆󱌧󰺮󷸄󱾋󸑴󷝥󱋎󵉐󳃵󱋎󵉐 󰵸
󰻤󰽧󵉐󲒩󰹢󱡸󰵨󳭌󼵼󷸽󴎤󲼑󰵷󷦳󲘜󴓊󰽥󴘲
󱌆󰹢󱡸󵒹󰻤󰽧󸛈󱐔 󴓊󰽥󰼔󲘌󶩝󳙧󹁻󱠥
󳃵󴦠󴧇 󵉐󴙂󲳴󹏣󱲉󲕔󱌼󰾫󵈾 󰵷󷦳󲘆
󰹢󱡸󳃵󸿢󰻞󸑴󷝥󰻤󰽧󱁝󳙖 󳦣󶑒󳍈󳧉󵒹
󳥀󳙖󱜴󶡊󰼔󱙭󱛺󲔝󱌌󲶎󼵼󱝖󷨟󲶎󱠥󶂹󶑢󲶎
󶡊󼵼󲪇󲘜󲘌󶩝󱁃󱁝󱿠󳙪 󰵷󷦳󱲉
󰵴󳃵󸿢󸑛󳙞󶔨󰻤󰽧󴦠󴬞󴙂󼵼󲁵󴩀󴱍󵒹󷕚
󴩿
󼬣󻱻󽴔 󺕧󽴔 󺃟󻳓󻰧󽴔 󻯓󼪧󻰓󽴔 󻷓󻱃󺳳󺽃󽴔 󼉸󻳓
󻷠󻪟 󻰓󽴔 󻌓󺕧󽴔 󻞄󺋿󻪟󽴔 󺙇󼉫󻞫󼕳󻺏
󺺗󻞼󻞫󻫳󻰏󽴔󻀋󻃸󻮇󻱃󺕧󽴔󻀋󽴔󼝏󺌏󻪟
󺙇󼉫󺣧󻪃󻗫󺝣󽴔 󻨗󺣧󺼿󽴔 󺐒󻆠󺇋󽴔 󺃨󻰏󽴔 󻨰󼆃󺴫
󼄓󻮛󻺓󽴔 󻀋󺅃󻰏󽴔 󺞳󺹇󽴔 󻱴󼌧󺹋󽴔 󼉸󻳓󼨧󺄿󺕧
󼉸󻳓󼨧󺝣󽴔 󺢨󻨗󽴔 󺋇󽴔 󻯓󻪟󽴔 󺫟󺝣󽴔 󺃏󺌛󻱃󻪟
󺤟󻪃󻗫󺝣󽴔 󻨗󺣸󺞗󺞳 󺞳󺹇󽴔 󻳓󻱟󽴔 󻳫󼥗󺇋
󺺗󼃻󺃏󻺏󺴫󽴔󻳫󼥗󻰧󽴔󻪃󺩳󽴔󻉏󻉓󻪟󺢓󽴔󻨰󼆃󺹋󽴔󻪝
󻺏󺹃󻺏󽴔󻨙󺢓󺴬󻷋󻰧󼨧󻞼󻞫󻫳󻨰󼆃󺝣󽴔󺆯󻱴󽴔󻃞
󺫟󺝣󽴔󼬣󻱻󽴔󻯓󼪧󻰓󽴔󼇗󺱧󼨯󽴔󻛧󽴔󻱗󻞄󺞗󺞳󻳓󻮟
󺇄󺋘󽴔 󻱴󼌧󺝣󽴔 󻞳󺖃󻪟󻗫󺺛󽴔 󻕻󻭸󼩃󻩋󼨸󺞗󺞳
󻳫󼥗󻱃󺕧󽴔 󻨰󻘇󻗫󺹻󺹋󽴔 󺃫󻴿󼨧󻺏󽴔 󺺗󻞼󻞫󻫳
󻱇󻹬󺣧󻺏󽴔 󻨙󻰏󽴔 󻆏󺆌󻰏󽴔 󻨗󻳓 󺊫󻳤󽴔 󻷏󻛧󽴔 󻃞
󻞫󻝳󼘫󽴔 󻘀󺝴󻰓󽴔 󻳏󼨧󻞫󼕻󽴔 󻛧󽴔 󻱗󻰋󺼿󽴔 󻇃󻹬󻰓
󻀃󼭷󼬣󼨸󺞗󺞳 󻃬󺅛󽴔 󻌪󺕫󽴔 󻩠󼇗󻬏󽴔 󺃨󻰏󽴔 󻉗󺐒
󻙛󻝳󺹋󺫟󺝣󽴔󺋋󼅧󻪟󽴔󺤟󻺏󽴔󺺗󻞼󻞫󻫳
󷵩󱟈󴎤󲼑󴎁󵒹󲺕󱸡
󷵩 󱟈 󼵼󲘮 󲳱 󱠥 󴎁 󲲓 󱁌 󲸂
󺆌󺆯󻷋󻰧󽴔󻃞󽴔󻅤󻳐󽴔󻳤󻇃

󳄲󼵸󳈄󶇳󼵹
󹌉󸢁󱎸󲘮󼵼
󸄦󱰑󼵸󳉽󰽞󼵹
󻇋󺸷󽴔󺞳󻮃
󺅃󺗗󽴔󺮿󺋿󽴔󺥳󺴫󺌇󺅛󽴔󺛓󺹃󺋿
󴎤󼶊󳥤󱔭󳍹󶇳󱐔
󲲔󶩉󱕜󵒹󱍅󸁰󱕜
󹄶󴙂󳈄󲳴󷦳
 󱐲󰾫󵈾󱑹
 󱋎󹄶󱋎󹄶
1. 
2. 
󴎤󲼑󼶊󲁵󳩔󲹠󵒹󴌵󳥤󴐟󱔔󵒹󷂱󴶄󸑷󳍹󲪇󰶃󲦻󶑒󳅨󲮔󼵼󲔐󲘜󱲉
󱐔󸷧󱝟󱌢󸽼󷦳󸡿󳜝󱞗󱔔󼵼󲹠󹄾󷦳󳉽󰽞󵉐󴙂
 󱲉󲹠󵳦󰵨󴂃󰾫󵈾󰷓󱑹󼵼
 󱋎󵉐󱙁󱋌󵕬󱑌󵉐󴋒
1. 󳉸󵤚󴦨
2. 󱌢󳍉
󼄇󺆯󻪟󽴔󼬫󻘀󻪿󺅿󻱃󻪕󺆯󽴔󼏫󻴇󽴔󻱗󻰋󺽃󻉓
󼮓󻪟󽴔󻱟󺢨󻰋󺴫󽴔󺎋󻺠󺞗󺞳󻰓󽴔󺞳󻞫󽴔󻞫󻱠󼨧󺳳󺽃󽴔󻳓󻮟󻰓󽴔󺌇󺅛
󺛛󺲻󻩋󼨸󺞗󺞳
 󻰓󽴔󼅧󻰛󽴔󻕻󻭸󼨧󺋿󽴔󻳓󻪟
 󻃿󼗿󺹻󺃏󽴔󼉸󻳓󽴔󺣯󽴔󺨛󺌛󻺏󽴔󻱴󼌧󺹋󽴔󼉸󻳓󼨧󻞼󻞫󻫳
1. 󼤫󻞫󽴔󺧀
2. 󺔓󺞳
CHINESEJAPANESEKOREAN
PHONE:
1-877-9 BRAVEN (1-877-927-2836)
REGISTER:
braven.com/register
SUPPORT:
braven.com/support
ONLINE:
braven.com
EMAIL:
support@braven.com
v02
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Braven Ready SOLO ユーザーマニュアル

タイプ
ユーザーマニュアル
このマニュアルも適しています

他の言語で