Thank you for purchasing Niigata Seiki Digital Calipers.
This is a precision measuring tool for making Inside, Outside, Step Height, and Depth measurements.
For safe and proper use, please read this instruction manual before use and follow the procedures described.
Please keep manual where it is accessible to user for future reference.
Keep this manual with the instrument if transferred or leased to a third party.
For inquiries about this product, please contact dealer or Niigata Seiki.
PART IDENTIFICATION AND FUNCTION
LEFT HAND DIGITAL VERNIER CALIPERS
PRECISION MEASURING TOOLS
D-***HL
Model No.
User Manual
Object to be measured is positioned between these surfaces.
For measuring outside dimensions.
Measures height of steps.
For measuring inside dimensions.
Position surfaces inside object to be measured.
For measuring depth.
Depth is measured between these two surfaces.
Supports LCD Display Unit.
Tighten to Prevent the Slide and Display from moving.
Displays digital measurement.
Open to access battery.
When pressed, Display will read "0.00".
For turning power ON/OFF.
Measuring Surfaces for outside measurements
Outside Jaws
Measuring surfaces for step measurements
Inside Jaws
Measuring surfaces for inside measurements
Depth Bar
Measuring surfaces for depth measurements
Scale
Lock Screw
LCD Display
Battery Cover
[ZERO] Button
[ON/OFF] Button
SAFETY PRECAUTIONS Please Observe
To prevent harm to yourself or others, and to prevent damage to
property, always follow the procedures marked by the following
symbols.
Read the manual and follow the directions.
Use of product other than as described in this manual
may cause accident.
Use only for measuring.
Use for any purpose other than measuring may
damage or wear the instrument. Improper use may
also cause accident.
Handle with Care.
Do not drop or subject instrument to excessive shock.
Do not place under heavy objects. Improper handling
may cause damage or poor accuracy.
Do not scratch instrument, for example by writing ID
number.
Avoid using in high electric fields, such as near
fluorescent lights or switching power supplies.
Incorrect value may be displayed on LCD.
Indicates risk of personal injury or property damage if not followed.
WARNING
Denotes a prohibition -
You MUST NOT do
Denotes a requirement -
You MUST do
Use and store only in environment meeting the
following conditions:
Dry location protected from rain, water, and oils.
Location that is not excessively hot.
Location protected from use by children and
unauthorized people.
Use in places contrary to the above may cause
damage to the product resulting in accident or injury.
Jaw Tips Are SharpHandle With Care.
Careless handling may cause injury.
Do not disassemble or modify.
Disassembly may damage product or cause accident.
For repair, please contact distributor .
Do not write on instrument with electric engraver.
Do not engrave instrument body or jaw, such as an ID
number with engraver or electric pen.
INSERTINGREPLACING BATTERY
AFTER USE CARESTORAGE
TROUBLESHOOTING
SERVICE
After use, wipe off any dirt or oil from
measuring surfaces, sliding surfaces, and
exterior using a dry cloth and perform rust
prevention treatment.
For rust prevention, lightly apply anti-rust oil, or place in
rust preventive bag.
Store with Jaws slightly open.
If Jaws are closed, expansion due to temperature changes
may cause excessive force which will cause inaccuracy.
Store in a cool, dry, and dark location in the
provided case.
Keep out of direct sunlight and moisture, and please
keep secure from unauthorized personnel.
Remove battery if Caliper will not be used for a
long period of time.
Batteries may leak if left in unused instrument for an
extended period.
PREPARATION FOR USE
Before using the calipers, please follow the steps below:
Wipe off rust proofing and dirt from measuring
surfaces and slide.
Contamination of surfaces may cause measurement
error.
Allow the calipers and object to be measured
time to reach the same temperature.
A temperature difference between the object to be
measured and the caliper may cause measurement
error. Allow enough time for the temperatures to
equilibrate.
HOW TO USE
Power ON/OFF
To turn on, press the [ON/OFF] Button.
To turn off, press the [ON/OFF] Button.
Power will automatically turn OFF after about 20 minutes with no
activity. Press the [ON/OFF] Button or move the Slide to turn ON.
Absolute Measurement Mode
Loosen the lock screw, and turn on power.
With jaws closed, press the [ZERO] Button.
When 0.00mm is displayed on LCD, Calipers is ready to
start measurement.
Comparisons Measure Mode
Loosen the lock screw, and turn on power.
With jaws open to desired reference position (any point
is OK,) press [ZERO] Button.
When 0.00mm is displayed on LCD, Calipers is ready
to start measurement.
Q. Nothing is displayed on LCD.
A. The battery may be running low, please replace
battery with a new one.
Q. With power on, the number on the LCD does not
change as Display Unit is moved.
A. Please reset by removing battery for about 30sec.,
and then replacing.
Q. Nothing happens when buttons are pressed.
A. Make sure battery is properly inserted.
Q. The correct value is not displayed.
A. High humidity may cause dampness. Please dry off
the instrument and use only in dry location.
Slide cover in direction of arrow.
Insert battery with (+) side outward.
Replace battery cover.
Use only SR44 type battery.
Notice
Not including quantization error (1 count)
If Instrument is not working properly, or if you have any
questions, please contact distributor.
Please note, manufacturer is unable to respond to
inquires or provide service directly. Please contact
distributor . Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
MAIL [email protected]
URL http://www.niigataseiki.co.jp
PRODUCT SPECIFICATIONS
Resolution : 0.01mm
Display : 5 Digit LCD
Auto Off : approx.20 min.
Maximum response speed
: Slide to Right .....1.5 m/s
Slide to Left ....... 0.75 m/s
Left/Right as shown in diagram at top of manual.
Operating Temperature Range : 0 C 40 C
Storage Temperature Range : 10 C 60 C
Power : (1x) SR44 Silver oxide Battery
Battery Life : approx. 1 years in normal use
Accessory : SR44 Silver oxide Battery (for test)
0.03mm
0.04mm
Model No. Measuring
Range
Maximum
permissible error Weight
D-150HL
D-200HL
D-300HL
150g
190g
250g
0
-
150mm
0
-
200mm
0
-
300mm
Remove
Battery
Cover
Measuring surfaces for
outside measurements
Outside Jaws
Measuring surfaces
for step measurements
Measuring surfaces for
inside measurements
LCD Display
Scale
Lock Screw
Battery Cover
Depth Bar
Model D-150HL shown.
Measuring surfaces
for depth measurements
Inside Jaws
[ON/OFF] Button
[ZERO] Button
2211 I92-K4
" 0.00"
ON/OFF
LCD
ZERO
ON/OFF
D-***HL
LCD
D-150HL
ON/OFF
ZERO
ON/OFF
ON ON/OFF
OFF ON/OFF
20OFF
ON/OFF
ON
"ZERO"
LCD "0.00mm"
"ZERO"
LCD "0.00mm"
ON LCD
30 0.01mm
LCD 5
20
1.5m/s
0.75m/s
040
1060
SR441
1
SR44
SR44
1
0.03
0.04
mm mm g
D-150HL
D-200HL
D-300HL
150
190
250
0
-
150
0
-
200
0
-
300
URL http://www.niigataseiki.co.jp
-
1
-
2
Niigata seiki D-300HL ユーザーマニュアル
- タイプ
- ユーザーマニュアル
他の言語で
- English: Niigata seiki D-300HL User manual
関連論文
-
Niigata seiki DT-300 ユーザーマニュアル
-
-
-
-
-
-
-
-
-
