Niigata seiki GDCS-150DS ユーザーマニュアル

タイプ
ユーザーマニュアル
Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
URL http://www.niigataseiki.co.jp
mm
mm
mm
LCD Display
Lock Screw
Output Connector
Scale
Battery Cover
[HOLD] Button
[ON/OFF] Button
Base
Depth Meas.Surface
[ZERO] Button
PARTS IDENTIFICATION
& FUNCTION
SAFETY PRECAUTIONS Please Observe
To prevent harm to yourself or others, and to prevent damage to
property, always follow the procedures marked by the following symbols.
Read the manual and follow the directions.
Use of product other than as described in this manual
may cause accident.
Use only for measuring.
Use for any purpose other than measuring may
damage or wear the instrument. Improper use may
also cause accident.
Handle with Care.
Do not drop or subject instrument to excessive shock.
Do not place under heavy objects. Improper handling
may cause damage or poor accuracy.
Do not scratch instrument, for example by writing ID
number.
Avoid using in high electric fields, such as near
fluorescent lights or switching power supplies.
Incorrect value may be displayed on LCD.
Use and store only in environment meeting the
following conditions:
Dry location protected from rain, water, and oils.
Location that is not excessively hot.
Location protected from use by children and
unauthorized people.
Use in places contrary to the above may cause
damage to the product resulting in accident or injury.
Do not disassemble or modify.
Disassembly may damage product or cause accident.
For repair, please contact distributor or place of purchase
.
Do not write on instrument with electric engraver.
Do not engrave instrument body or jaw, such as an ID
number with engraver or electric pen.
Wipe off oil, rust proofing, and dirt from measuring surfaces
and slide.
Contamination of surfaces may cause measurement error.
Allow the gauge and object to be measured time to reach
the same temperature.
A temperature difference between the object to be measured
and the gauge may cause measurement error. Allow time for the
temperatures to equilibrate.
Indicates risk of personal injury or property damage if not followed.
WARNING:
Denotes a prohibition
-You MUST NOT do
Denotes a requirement
-You MUST do
DIGITAL DEPTH GAUGE (Short Base)
Precision Measuring Tool For Depth Measurement
Thank you for purchasing Niigata Seiki Digital Depth Gauge (Short Base).
This product is a digital instrument for measuring depth.
For safe and proper use of this product, please read this instruction manual before use and follow the procedures described.
Keep this manual with the instrument if transferred or leased to a third party.
For inquiries about this product, please contact distributor or place of purchase.
GDCS-150DS
Model No.INSTRUCTION MANUAL
Flat Surface
Depth Meas.
Surface
Base
[ZERO]
Button
HOW TO USE
INSERTINGREPLACING BATTERY
AFTER USE CARE STORAGE
TROUBLESHOOTING
After use, wipe off any dirt or oil from measuring surfaces,
sliding surfaces, and exterior using a dry cloth and
perform rust prevention treatment.
For rust prevention, lightly apply anti-rust oil, or place in rust
preventive bag.
Store with Lock Screw loosened.
If stored with Lock Screw tight, expansion due to temperature
changes may cause excessive force which will cause
inaccuracy.
Store in a cool, dry, and dark location in the provided case.
Keep out of direct sunlight and moisture, and please keep
secure from unauthorized personnel.
Remove battery if Instrument will not be used for a long
period of time.
Batteries may leak if left in unused instrument for an extended
period.
Q. Nothing is displayed on LCD.
A.
The battery may be running low, please replace battery with a new one.
Q. With power on, the number on the LCD does not change
as Display Unit is moved.
A.
Please reset by removing battery for about 30sec., and then replacing.
Q. Nothing happens when buttons are pressed.
A. Make sure battery is properly inserted.
Q. The characters MIN , MAX, or are displayed on LCD.
A. Cycle power, or apply several long presses to [HOLD] Button.
Use as normal once character is off.
Q. The correct value is not displayed.
A. High humidity may cause dampness. Please dry off the
instrument and use only in dry location.
Slide cover in direction of arrow.
Insert battery with (+) side outward.
Replace battery cover.
Use care to avoid damaging
terminals when inserting
battery.
Terminals may be broken if battery is pressed straight down.
Insert battery at angle, underneath the small hook, as shown.
Power ON/OFF
To turn on, press the [ON/OFF] Button.
To turn off, press the [ON/OFF] Button.
With power on, press the [HOLD] Button to fix the value on the display.
Absolute Measurement
Turn on power, and loosen the Lock Screw.
Place the Base on a flat surface, and push the Scale down.
When the Measurement Surface contacts the surface, press the
[ZERO] Button. (Fig.1)
The Display will read "0.00mm" and the gauge is ready for
measurements.
When placed on workpiece with Measurement Surface lowered
into groove, the depth of the groove will be displayed. (Fig.2)
Comparative Measurement
Turn on power, and loosen the Lock Screw.
Place the Base on the Reference Part and push the Scale down.
When the Measurement Surface is in contact with the bottom of
the groove, press the [ZERO] Button. (Fig.3)
The Display will read "0.00mm" and the gauge is ready for
measurements.
When placed on workpiece with Measurement Surface lowered
into groove, the difference the difference in depth compared to
the Reference Part will be displayed. (Fig.4)
Battery
Cover
Remove
Hook
Slide In
Pressed Down
SERVICE
If Instrument is not working properly, or if you have any
questions, please contact distributor or place of purchase.
Please note, manufacturer is unable to respond to inquires or
provide service directly. Please contact distributor or place of
purchase.
SPECIFICATIONS
[ZERO]
Button
Difference in
Depth
compared to
Reference Part
Reference Part
Reference surface placed on face of
workpiece.
Insert into groove to measure depth.
Displays digital measurement.
Tighten to prevent the slide and display
from moving.
When pressed, "HOLD"Icon appears on
Display and measurement will be fixed.
PREPARATION FOR USE Before using, please follow the steps below
Base
Depth Meas.Surface
LCD Display
Lock Screw
[HOLD] Button
Connect to optional Bluetooth Box to
send measurements to PC.
Open to access battery.
When pressed, Display will read "0.00"
For turning power ON / OFF.
Supports LCD Display Unit.
Output Connector
Battery Cover
[ZERO] Button
[ON/OFF] Button
Scale
Notice Use only CR2032 type
battery.
Battery
Terminals
Battery
Terminals
Measurement Range
Resolution
Maximum Permissible Error
Display
Auto Off
Maximum response speed
Operating Temp. Range
Storage Temp. Range
Power
Battery Life
Weight
Accessory
0-150mm
0.01mm
0.03mm
Not including quantization error (1 count )
5 Digit LCD
approx. 20 min
Slide in pos. dir.1.5m/s
Slide in neg. dir.0.75m/s
0 C40 C
10 C60 C
(1x) CR2032 Lithium Battery
approx. 2.5 years in normal use
175g
CR2032 Lithium Battery (for test)
Push down
Push down
(Fig.4)(Fig.3)
(Fig.1) (Fig.2)
Workpiece
Scale Scale
Workpiece
mm
mm
mm
mm
mm
mm
mm
URL http://www.niigataseiki.co.jp
  • Page 1 1
  • Page 2 2

Niigata seiki GDCS-150DS ユーザーマニュアル

タイプ
ユーザーマニュアル

他の言語で