Battery
Thank you for purchasing Niigata Seiki Wire Rope Calipers.
This product is designed for precise and repeatable measurement of wire rope.
PART IDENTIFICATION AND FUNCTION
WIRE ROPE CALIPERS
Precision Measuring Tool
For Wire Rope Diameter Measurements GDCS
-
100WR
Model No.
User Manual
SAFETY PRECAUTIONS Please Observe
To prevent harm to yourself or others, and to prevent damage to
property, always follow the procedures marked by the following
symbols.
Read the manual and follow the directions.
Use of product other than as described in this manual
may cause accident.
Use only for measuring.
Use for any purpose other than measuring may
damage or wear the instrument. Improper use may
also cause accident.
Handle with Care.
Do not drop or subject instrument to excessive shock.
Do not place under heavy objects. Improper handling
may cause damage or poor accuracy.
Do not scratch instrument, for example by writing ID
number.
Avoid using in high electric fields, such as near
fluorescent lights or switching power supplies.
Incorrect value may be displayed on LCD.
Indicates risk of personal injury or property damage if not followed.
WARNING
Denotes a prohibition -
You MUST NOT do
Use and store only in environment meeting the
following conditions:
Dry location protected from rain, water, and oils.
Location that is not excessively hot.
Location protected from use by children and
unauthorized people.
Use in places contrary to the above may cause
damage to the product resulting in accident or injury.
Do not disassemble or modify.
Disassembly may damage product or cause accident.
For repair, please contact distributor or place of
purchase.
Do not write on instrument with electric engraver.
Do not engrave instrument body or jaws, such as an ID
number with engraver or electric pen.
Denotes a requirement -
You MUST do
For positioning outside of Wire Rope for measurement.
Surfaces for measuring Outside Diameter of Wire Rope.
Displays digital measurement.
Tighten to prevent the slide and display from moving.
When pressed, "HOLD"Icon appears on Display and measurement will be fixed.
Connect to optional BluetoothBOX to send measurements to PC.
Open to access battery.
When pressed, Display will read "0.00".
For turning power ON / OFF.
Supports LCD Display Unit.
Jaws
Measuring Surfaces
LCD Display
Lock Screw
[HOLD] Button
Output Connector
Battery Cover
[ZERO] Button
[ON/OFF] Button
Scale
Measuring Surfaces
Jaws
Scale
Lock Screw
LCD Display
Output Connector
Battery Cover
[HOLD] Button
[ON/OFF] Button [ZERO] Button
Niigata seiki Co., Ltd.
5-3-14, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-33-5522 Fax. : +81-256-33-5518
MAIL [email protected]
URL http://www.niigataseiki.co.jp
Power ON/OFF
To turn on, press the [ON/OFF] Button.
To turn off, press the [ON/OFF] Button.
With power on, press the [HOLD] Button to fix the value on
the display.
Absolute Measurement Mode
Loosen the lock screw, and turn on power.
With jaws closed, press the [ZERO] Button.
When 0.00mm is displayed on LCD, Calipers is ready to
start measurement.
Comparisons Measure Mode
Loosen the lock screw, and turn on power.
With jaws open to desired reference position (any point is
OK,) press [ZERO] Button.
When 0.00mm is displayed on LCD, Calipers is ready to
start measurement.
Before using the calipers, please follow the steps below:
Wipe off rust proofing and dirt from measuring
surfaces and slide.
Contamination of surfaces may cause measurement error.
Allow the calipers and object to be measured time to
reach the same temperature.
A temperature difference between the object to be measured
and the caliper may cause measurement error. Allow enough
time for the temperatures to equilibrate.
Correct Wrong
INSERTINGREPLACING BATTERY
AFTER USE CARESTORAGE
TROUBLESHOOTING
PRODUCT SPECIFICATIONS
SERVICE
After use, wipe off any dirt or oil from measuring
surfaces, sliding surfaces, and exterior using a dry
cloth and perform rust prevention treatment.
For rust prevention, lightly apply anti-rust oil, or place in rust
preventive bag.
Store with Lock Screw loosened.
If stored with Lock Screw tight, expansion due to temperature
changes may cause excessive force which will cause inaccuracy.
Store in a cool, dry, and dark location in the provided
case.
Keep out of direct sunlight and moisture, and please keep
secure from unauthorized personnel.
Remove battery if Caliper will not be used for a long
period of time.
Batteries may leak if left in unused instrument for an extended
period.
Q. Nothing is displayed on LCD.
A. The battery may be running low, please replace battery
with a new one.
Q. With power on, the number on the LCD does not change
as Display Unit is moved.
A. Please reset by removing battery for about 30sec., and
then replacing.
Q. Nothing happens when buttons are pressed.
A. Make sure battery is properly inserted.
Q. The characters MIN , MAX , or are displayed on LCD.
A. Cycle power, or apply several long presses to [HOLD]
Button. Use as normal once character is off.
Q. The correct value is not displayed.
A. High humidity may cause dampness. Please dry off the
instrument and use only in dry location.
Measuring Range : 0
-
100mm
For measuring rope of maximum diameter of 38mm.
Resolution : 0.01mm
Maximum Permissible Error
: 0.05 mm
Not including quantization error (1 count)
Display : 5 Digit LCD
Auto Off : approx. 20 min.
Maximum response speed
: Slide to Right.....1.5 m/s
Slide to Left .......0.75 m/s
Left/Right as shown in diagram at top of manual.
Operating Temperature Range : 0 C 40 C
Storage Temperature Range : 10 C 60 C
Power : (1x) CR2032 Lithium Battery
Battery Life : approx. 2.5 years in normal use
Weight : 170g
Accessory : CR2032 Lithium Battery (for test)
Slide cover in direction of arrow.
Insert battery with (+) side outward.
Replace battery cover.
Use care to avoid damaging
terminals when inserting
battery.
Terminals may be broken if battery is pressed straight down.
Insert battery at angle, underneath the small hook, as shown.
Use only CR2032 type
battery.
Battery
Cover
Remove
Notice
Hook
Slide In
If Instrument is not working properly, or if you have any
questions, please contact distributor or place of purchase.
Please note, manufacturer is unable to respond to inquires or
provide service directly. Please contact distributor or place of
purchase.
Battery
Pressed Down
Terminals
Terminals
Object to
Measure Jaw
Object to
Measure Jaw
For safe and proper use, please read this instruction manual before use and follow the procedures described.
Please keep manual where it is accessible to user for future reference.
Keep this manual with the instrument if transferred or leased to a third party.
For inquiries about this product, please contact dealer or Niigata Seiki.
PREPARATION FOR USE
HOW TO USE
GDCS-100WR
0-100mm 38mm
0.01mm
0.05mm 1
LCD 5
20
1.5m/s
0.75m/s
040
1060
CR20321
2.5
170g
CR2032
CR2032
2203I346-K1
(0256)33-5502
( )
FAX(0256)33-5528
URL http://www.niigataseiki.co.jp
LCD
ON LCD
30
LCD MAX MIN
HOLD
ON/OFF
ON ON/OFF
OFF ON/OFF
ON HOLD
"ZERO"
LCD "0.00mm"
"ZERO"
LCD "0.00mm"
Bluetooth BOX
" 0.00"
ON/OFF
ZERO
ON/OFF
LCD
HOLD
ON/OFFZERO
LCD
HOLD "HOLD"
/
