Pioneer PDP-435HDG ユーザーマニュアル

PLASMA DISPLAY SYSTEM

SISTEMA DE PANTALLA DE PLASMA

SISTEMA DE MONITOR DE PLASMA

PDP-505HDG

PDP-435HDG

Operating Instructions

Manual de instrucciones

Manual de instruções

CAUTION: THE POWER SWITCH DOES NOT COMPLETELY

SEPARATES THE UNIT FROM THE MAINS IN OFF POSITION.

THEREFORE INSTALL THE UNIT SUITABLE PLACES EASY TO

DISCONNECT THE MAINS PLUG IN CASE OF THE ACCIDENT. THE

MAINS PLUG OF UNIT SHOULD BE UNPLUGGED FROM THE WALL

SOCKET WHEN LEFT UNUSED FOR A LONG PERIOD OF TIME.

NOTE: This equipment has been tested and found to

comply with the limits for a class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no

guarantee that interference will not occur in a particu-

lar installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment off and on,

the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and

receiver.

— Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV tech-

nician for help.

Information to User

Alteration or modifications carried out without appro-

priate authorization may invalidate the user’s right to

operate the equipment.

CAUTION:

This product satisfies FCC regulations when shielded

cables and connectors are used to connect the unit to

other equipment. To prevent electromagnetic interfer-

ence with electric appliances such as radios and tele-

visions, use shielded cables and connectors for

connections.

FEDERAL COMMUNICATIONS COMMISSION

DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Op-

eration is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired opera-

tion.

Product Name: Plasma Display System

(Plasma Display)

(Media Receiver)

Model Number: PDP-505HDG PDP-435HDG

(PDP-505PG) (PDP-435PG)

(PDP-R05G) (PDP-R05G)

Product Category: Class B Personal Computers & Pe-

ripherals

Responsible Party Name: PIONEER ELECTRONICS

(USA), INC., Customer Support Div.

Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760

U.S.A.

Phone: (800) 421-1625

For Business Customer URL

http://www.PioneerUSA.com

English

WARNING: BEFORE PLUGGING IN THE UNIT FOR THE FIRST

TIME, READ THE FOLLOWING SECTION CAREFULLY.

THE VOLTAGE OF THE AVAILABLE POWER SUPPLY DIFFERS

ACCORDING TO COUNTRY OR REGION. BE SURE THAT THE

POWER SUPPLY VOLTAGE OF THE AREA WHERE THIS UNIT WILL

BE USED MEETS THE REQUIRED VOLTAGE (E.G. 230V OR 120V)

WRITTEN ON THE REAR PANEL.

WARNING: THIS PRODUCT EQUIPPED WITH A THREE-WIRE

GROUNDING (EARTHLING) TYPE PLUG. A PLUG HAVING A THIRD

(GROUNDING, EARTHLING) PIN, IT WILL ONLY FIT INTO A

GROUNDING (EARTHLING) TYPE POWER OUTLET. THIS IS A

SAFETY FEATURE. IF YOU ARE UNABLE TO INSERT THE PLUG

INTO THE OUTLET, CONTACT YOUR ELECTRICIAN TO REPLACE

YOUR OBSOLETE OUTLET. DO NOT DEFEAT THE SAFETY

PURPOSE OF THE GROUNDING (EARTHLING) TYPE PLUG.

The following symbols are found on labels

attached to the product. They alert the operators

and service personnel of this equipment to any

potentially dangerous conditions.

WARNING

This symbol refers to a hazard or unsafe

practice which can result in personal injury or

property damage.

CAUTION

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

WARNING:

NO NAKED FLAME SOURCES SUCH AS LIGHTED

CANDLE, SHOULD BE PLACED ON THE APPARATUS.

IF NAKED FLAME SOURCES ACCIDENTALLY FALL DOWN, FIRE

SPREAD OVER THE APPARATUS THEN MAY CAUSE FIRE.

VENTILATION: WHEN INSTALLING THIS UNIT, MAKE SURE

TO LEAVE SPACE AROUND THE UNIT FOR VENTILATION TO

IMPROVE HEAT RADIATION. FOR THE MINIMUM SPACE

REQUIRED, SEE PAGES 16 AND 17.

WARNING: SLOTS AND OPENINGS IN THE CABINET ARE

PROVIDED FOR VENTILATION AND TO ENSURE RELIABLE

OPERATION OF THE PRODUCT AND TO PROTECT IT FROM

OVERHEATING, TO PREVENT FIRE HAZARD, THE OPENINGS

SHOULD NEVER BE BLOCKED AND COVERED WITH ITEMS, SUCH

AS NEWSPAPERS, TABLE-CLOTHS, CURTAINS, ETC. ALSO DO NOT

PUT THE APPARATUS ON THE THICK CARPET, BED, SOFA, OR

FABRIC. HAVING A THICK PILE.

Contents

4

En

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you

have finished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown

in the explanatory drawings. However the method of connecting and operating the unit is the same.

01 Important User Guidance Information

02 Safety Precautions

03 Operational Precautions

04 Supplied Accessories

Plasma Display ................................................................... 11

Media Receiver.................................................................... 11

05 Part Names

Plasma Display ................................................................... 12

Media Receiver.................................................................... 13

Remote control unit ............................................................ 15

06 Preparation

Allowed operation range of the remote control unit ....... 16

Installing the Plasma Display ............................................ 16

Installing the Media Receiver ............................................ 17

Installing the Media Receiver vertically ...................... 18

Setting the system .............................................................. 19

Routing cables .................................................................... 20

Using the remote control unit ........................................... 21

Cautions regarding the remote control unit .............. 21

Inserting batteries ......................................................... 21

Cautions regarding batteries ....................................... 21

Basic connections .............................................................. 22

Connecting to an antenna ........................................... 22

Connecting the power cord ......................................... 22

07 Watching TV

Turning on the power .......................................................... 23

Turning off the power .......................................................... 23

Changing channels ............................................................ 24

Changing the volume and sound ...................................... 25

Using the multiscreen functions ....................................... 27

Splitting the screen ...................................................... 27

Freezing images ............................................................ 27

08 Basic Adjustment Settings

Using the menu .................................................................. 28

AV mode menus............................................................ 28

PC mode menus ........................................................... 29

Menu operation keys .................................................... 30

Setting up TV channels automatically .............................. 30

Using Auto Installation ................................................ 30

Using Auto Search ....................................................... 31

Setting up TV channels manually ...................................... 31

Using Manual Adjust ................................................... 31

Labeling TV channels ................................................... 33

Setting Child Lock ......................................................... 33

Sorting preset TV channels ................................................ 34

Language setting ................................................................ 34

AV Selection ........................................................................ 35

Picture adjustments ........................................................... 36

PureCinema .................................................................. 37

Color temperature ........................................................ 37

MPEG NR....................................................................... 38

DNR ............................................................................... 39

CTI .................................................................................. 39

DRE ................................................................................ 40

Color Management ....................................................... 40

Sound adjustments ............................................................ 41

FOCUS ........................................................................... 41

Front Surround .............................................................. 42

Power Control ...................................................................... 42

Energy Save .................................................................. 42

No Signal off (AV mode only) ....................................... 43

No Operation off (AV mode only) ................................ 43

Power Management (PC mode only) .......................... 44

Contents

English

5

En

09 Using the Teletext Functions

What is Teletext? .................................................................. 45

Operating the Teletext basics ............................................. 45

Turning on and off Teletext ........................................... 45

Selecting and operating Teletext pages ...................... 45

Displaying subpages .................................................... 46

10 Enjoying through External Equipment

Watching a DVD image ...................................................... 47

Connecting a DVD player ............................................. 47

Displaying a DVD image .............................................. 47

Watching a VCR image ...................................................... 48

Connecting a VCR ........................................................ 48

Displaying a VCR image ............................................... 48

Watching broadcasts via a digital tuner ........................... 49

Connecting a digital tuner ........................................... 49

Displaying broadcasts via a digital tuner ................... 49

Enjoying a game console and watching

camcorder images .............................................................. 50

Connecting a game console or camcorder ................ 50

Displaying an image from the game console or

camcorder ..................................................................... 50

Watching an image from a personal computer ............... 51

Connecting a personal computer ............................... 51

Displaying an image from a personal computer ....... 51

Computer compatibility chart ...................................... 51

Enjoying through audio equipment in connection .......... 52

Connecting audio equipment ...................................... 52

Using HDMI Input ............................................................... 53

Connecting control cords .................................................. 55

About SR+ .................................................................... 55

11 Useful Adjustments Settings

Adjusting image positions (AV mode only) ...................... 56

Adjusting image positions and clock automatically

(PC mode only) .................................................................... 56

Adjusting image positions and clock manually

(PC mode only) .................................................................... 57

Color system setting (AV mode only) ................................ 57

Select a screen size ............................................................ 58

Manual Selection .......................................................... 58

Auto Selection ............................................................... 59

Wide screen signalling (WSS) (AV mode only) ................ 59

Picture aspect ratio (AV mode only) .................................. 60

Changing the brightness at both sides of the screen

(Side Mask) .......................................................................... 60

Sleep Timer .......................................................................... 61

Using a password (AV mode only) .................................... 61

Entering a password ..................................................... 61

Changing the password ............................................... 62

Resetting the password ............................................... 62

12 Appendix

Troubleshooting .................................................................. 63

Standard Channel Allocation Selections for the

Countries and Regions ....................................................... 65

Specifications ...................................................................... 66

01 Important User Guidance Information

6

En

In order to obtain maximum enjoyment from this

Pioneer PureVision PDP-505HDG/PDP-435HDG Plasma

Display System, please first read this information

carefully.

With the Pioneer PureVision PDP-505HDG/PDP-

435HDG, you can be assured of a high quality Plasma

Display System with long-life and high reliability. To

achieve images of exceptional quality, this Pioneer

Plasma Display System incorporates state-of-the-art

design and construction, as well as very precise and

highly advanced technology.

Over the course of its lifetime, the luminosity of the

Pioneer PDP-505HDG/PDP-435HDG Plasma Display

System will diminish very slowly, such as with all

phosphor-based screens (for example, a traditional

tube-type television). To enjoy beautiful and bright

images on your Pioneer Plasma Display System for a

long time, please carefully read and follow the usage

guidelines below:

Usage guidelines

All phosphor-based screens (including conventional

tube-type televisions) can be affected by displaying

static images for a prolonged period. Plasma Display

System’s are no exception to this rule. After-image and

permanent effects on the screen can be avoided by

taking some basic precautions. By following the recom-

mendations listed below, you can ensure longer and

satisfactory results from your plasma:

• Whenever possible, avoid frequently displaying the

same image or virtually still moving pictures (e.g.

closed-captioned images or video game images

which have static portions).

• Do not display Teletext for a prolonged period of time.

• Avoid viewing the On Screen Display for extended

periods, from a decoder, DVD player, VCR and all

other components.

• Do not leave the same picture freeze-framed or

paused continuously over a long period of time, when

using the still picture mode from a TV, VCR, DVD

player or any other component.

• Images which have both very bright areas and very

dark areas side by side should not be displayed for a

prolonged period of time.

• When playing a game, the “GAME” mode setting

within “AV Selection” is strongly recommended.

However, please limit its use to less than 2 hours at a

time.

•After playing a game, or displaying a PC image or any

still image, it is best to view a normal moving picture

in the “WIDE” or “FULL” screen setting for more than

3 times the length of the previous still moving image.

•After using the Plasma Display System, always

switch the display to “STANDBY” mode.

Installation guidelines

The Pioneer PureVision PDP-505HDG/PDP-435HDG

Plasma Display System incorporates a very thin design.

To ensure safety, please take the proper measures to

mount or install the Plasma Display, in order to prevent

the unit from tipping over in the event of vibration or

accidental movement.

This product should be installed by using only parts

and accessories designed by PIONEER. Use of acces-

sories other than the PIONEER stand or installation

bracket may result in instability, and could cause injury.

For custom installation, please consult the dealer

where the unit was purchased. To ensure correct

installation, experienced and qualified experts must

install the unit. PIONEER will not be held responsible

for accident or damage caused by the use of parts and

accessories manufactured by other companies.

To avoid malfunction and overheating, make sure that

the vents on the main unit are not blocked when

installing to ensure proper heat emission:

• Distance the unit slightly from other equipment,

walls, etc. For the minimum space required around

the unit, see pages 16 and 17.

• Do not fit the unit inside narrow spaces where

ventilation is poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to

remove dust build-up, by using a vacuum cleaner set

to its lowest suction setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over except the case of

vertical installation of the Media Receiver.

• Do not reverse the product.

Using the unit without proper ventilation may cause the

internal temperature to rise, and could result in pos-

sible malfunction. When the surrounding or internal

temperature exceeds a certain degree, the display will

automatically power off in order to cool the internal

electronics and prevent hazardous occurrences.

Any malfunction may occur due to: an inappropriate

installation site, improper assembly, installation,

mounting, or operation of this product, modifications

made to the product. However, PIONEER cannot be

held responsible for such accidents or malfunction.

Typical effects and characteristics of a phosphor-based

matrix display, e.g., permanent residual images upon

the phosphor of the panel, and the existence of a

minute number of inactive light cells in the screen, are

not covered by local warranties.

01Important User Guidance Information

English

7

En

Panel sticking and after-image lag

• Displaying the same images such as still images for

a long time may cause after-image lagging. This may

occur in the following two cases.

1. After-image lagging due to remaining electrical

load

When image patterns with very high peak luminance

are displayed for more than 1 minute, after-image

lagging may occur due to the remaining electric load.

The after-images remaining on the screen will disap-

pear when moving images are displayed. The time for

the after-images to disappear depends on the lumi-

nance of the still images and the time they had been

displayed.

2. After-image (lag image) due to burning

Avoid displaying the same image on the Plasma

Display continuously over a long period of time. If the

same image is displayed continuously for several

hours, or for shorter periods of time over several days, a

permanent after-image may remain on the screen due

to burning of the fluorescent materials. Such images

may become less noticeable if moving images are later

displayed, but they will not disappear completely.

• The energy save function can be set to help prevent

damage from screen burning (see page 42).

02 Safety Precautions

8

En

Electricity is used to perform many useful functions, but it

can also cause personal injuries and property damage if

improperly handled. This product has been engineered and

manufactured with the highest priority on safety. However,

improper use can result in electric shock and/or fire. In order

to prevent potential danger, please observe the following

instructions when installing, operating and cleaning the

product. To ensure your safety and prolong the service life of

your product, please read the following precautions carefully

before using the product.

1. Read instructions—All operating instructions must be

read and understood before the product is operated.

2. Keep this manual in a safe place—These safety and

operating instructions must be kept in a safe place for

future reference.

3. Observe warnings—All warnings on the product and in

the instructions must be observed closely.

4. Follow instructions—All operating instructions must be

followed.

5. Cleaning—Unplug the power cord from the AC outlet

before cleaning the product. Use a damp cloth to clean

the product. Do not use liquid cleaners or aerosol clean-

ers.

6. Attachments—Do not use attachments not recom-

mended by the manufacturer. Use of inadequate attach-

ments can result in accidents.

7. Water and moisture—Do not use the product near water,

such as bathtub, washbasin, kitchen sink and laundry

tub, swimming pool and in a wet basement.

8. Stand—Do not place the product on an unstable cart,

stand, tripod or table. Placing the product on an unstable

base can cause the product to fall, resulting in serious

personal injuries as well as damage to the product. Use

only a cart, stand, tripod, bracket or table recommended

by the manufacturer or sold with the product. When

mounting the product on a wall, be sure to follow the

manufacturer’s instructions. Use only the mounting

hardware recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be

moved with utmost care. Sudden stops, excessive force

and uneven floor surface can cause the product to fall

from the cart.

10. Ventilation—The vents and other openings in the cabinet

are designed for ventilation. Do not cover or block these

vents and openings since insufficient ventilation can

cause overheating and/or shorten the life of the product.

Do not place the product on a bed, sofa, rug or other

similar surface, since they can block ventilation openings.

This product is not designed for built-in installation; do

not place the product in an enclosed place such as a

bookcase or rack, unless proper ventilation is provided or

the manufacturer’s instructions are followed.

11. Power source—This product must operate on a power

source specified on the specification label. If you are not

sure of the type of power supply used in your home,

consult your dealer or local power company.

12. Power cord protection—The power cords must be routed

properly to prevent people from stepping on them or

objects from resting on them. Check the cords at the

plugs and product.

13. The plasma Display used in this product is made of glass.

Therefore, it can break when the product is dropped or

applied with impact. Be careful not to be injured by

broken glass pieces in case the plasma Display breaks.

14. Overloading—Do not overload AC outlets or extension

cords. Overloading can cause fire or electric shock.

15. Entering of objects and liquids—Never insert an object

into the product through vents or openings. High voltage

flows in the product, and inserting an object can cause

electric shock and/or short internal parts. For the same

reason, do not spill water or liquid on the product.

16. Servicing—Do not attempt to service the product yourself.

Removing covers can expose you to high voltage and

other dangerous conditions. Request a qualified service

person to perform servicing.

17. Repair—If any of the following conditions occurs, unplug

the power cord from the AC outlet, and request a qualified

service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when

objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as

described in the operating instructions.

Do not touch the controls other than those described

in the operating instructions. Improper adjustment of

controls not described in the instructions can cause

damage, which often requires extensive adjustment

work by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that

the product needs servicing.

18. Replacement parts—In case the product needs replace-

ment parts, make sure that the service person uses

replacement parts specified by the manufacturer, or those

with the same characteristics and performance as the

original parts. Use of unauthorized parts can result in fire,

electric shock and/or other danger.

19. Safety checks—Upon completion of service or repair

work, request the service technician to perform safety

checks to ensure that the product is in proper operating

condition.

20. Wall or ceiling mounting—When mounting the product

on a wall or ceiling, be sure to install the product

according to the method recommended by the manufac-

turer.

21. Heat sources—Keep the product away from heat sources

such as radiators, heaters, stoves and other heat- generat-

ing products (including amplifiers).

22. Unplug the power cord from the AC outlet before install-

ing the speakers.

23. Never expose the screen of the Plasma Display to a strong

impact, for example, by hitting it. The screen may be

broken, resulting in fire or personal injury.

24. Do not expose the Plasma Display to direct sunlight for a

long period of time. The optical characteristics of the front

protection panel changes, resulting in discoloration or

warp.

25. The Plasma Display weighs about 38 kg (83.8 lbs.) for the

PDP-505PG and about 30.5 kg (67.3 lbs.) for the PDP-

435PG. Because it has small depth and is unstable,

unpack, carry, and install the product with one more

person at least and use the handles.

02Safety Precautions

English

9

En

• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.

• Use M8 screws, which go 12 to 18 mm in depth from the mounting surface of the Plasma Display. See the side

view above.

• Be careful not to block the ventilation opening at the rear of the Plasma Display.

• Be sure to install the Plasma Display on a flat surface because it contains glass.

• The screw holes other than the above are to be used only for the specified products. Never use them for

mounting non-specified products.

• Do not mount or remove the Plasma Display to or from the stand, with speakers attached.

• It is strongly recommended to use the optional PIONEER mounting products.

• PIONEER shall not be liable for any personal injury or product damage that results from the use of mounting

items other than the optional PIONEER products.

Installation Precautions

Observe the following precautions when installing with any items such as the optional stand.

When using the optional stand, brackets, or equivalent items

• Ask your dealer to perform the installation.

• Be sure to use the supplied bolts.

•For details, see the instruction manual that comes with the optional stand (or equivalent items).

When using other items

• Consult your dealer.

• The following six mounting holes can be used for the installation:

Median line

Mounting hole Mounting hole

Rear view

Median line

Side view

Plasma

Display

Mounting surface

12 to 18 mm

M8 screw

Mounting

bracket (or

equivalent item)

03 Operational Precautions

10

En

PIONEER bears no responsibility for any damages

arising from incorrect use of the product by you or

other people, malfunctions when in use, other product

related problems, and use of the product except in

cases where the company must be liable.

Plasma Display protection function

When still images (such as photos and computer

images) stay on the screen for an extended period of

time, the screen will be slightly dimmed. This is be-

cause the protection function of the Plasma Display

automatically adjusts the brightness to protect the

screen when detecting still images; so this does not

designate malfunction. The screen is dimmed when a

still image is detected for about three minutes.

Infrared rays

The Plasma Display releases infrared rays because of

its characteristics. Depending on how the Plasma

Display is in use, the remote controls of nearby equip-

ment may be adversely affected or wireless head-

phones using infrared rays are interfered by noise. If

this is the case, place that equipment at a location

where its remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it

emits a small amount of noise. If you place such

equipment as an AM radio, personal computer, and

VCR close to this product, that equipment may be

interfered. If this happens, place that equipment far

enough from this product.

Fan motor noise

When ambient temperature of the Media Receiver

becomes high, the rotation speed of the cooling fan

motor increases. This may make you feel that the fan

motor is noisy at such an occasion.

Do not attach such items as labels and tape to the

product.

• This may result in the discoloration or scratch of the

cabinet.

When not using the product for a long period of

time

• If you do not use the product for a long period of time,

the functions of the product may be adversely af-

fected. Switch on and run the product occasionally.

Condensation

• Condensation may take place on the surface or inside

of the product when the product is rapidly moved

from a cold place to a warm place or just after a

heater is switched on in winter morning, for example.

When condensation takes place, do not switch on the

product and wait until condensation disappears.

Using the product with condensation may result in

malfunction.

Cleaning the screen

• When cleaning the screen of this product, gently

wipe it with a dry soft cloth; the supplied cleaning

cloth or other similar cloths (e.g., cotton and flannel).

If you use a hard cloth or rub the screen hard, the

surface of the screen will be scratched.

• If you clean the surface of the screen with a wet

cloth, water droplets on the surface may enter into

the product, resulting in malfunction.

Cleaning the cabinet

• The cabinet of this product is mostly composed of

plastic. Do not use chemicals such as benzine or

thinner to clean the cabinet. Using these chemicals

may result in quality deterioration or coating removal.

• Do not expose the product to volatile gas or fluid

such as pesticide. Do not make the product contact

with rubber or vinyl products for a long period of time.

The effect of plasticizer in the plastic may result in

quality deterioration or coating removal.

• If you clean the surface of the cabinet with a wet

cloth, water droplets on the surface may enter into

the product, resulting in malfunction.

Handles at the rear of the Plasma Display

• Do not remove the handles from the rear of the

Plasma Display.

• When moving the Plasma Display, ask another

person for help and use the handles attached to the

rear of the Plasma Display. Do not move the Plasma

Display by holding only a single handle. Use the

handles as shown.

• Do not use the handles to hang the product when

installing or carrying the product, for example. Do not

use the handles for the purpose of preventing the

product from tilting over.

04Supplied Accessories

English

11

En

Plasma Display

Media Receiver

Warranty card

Operating instructions

• Always use the power cord supplied with the Plasma

Display and the one supplied with the Media Receiver

for each respective unit.

Remote control unit

Screw x 4

(for stand)

Screw hole cap x 4

Stand System cable (3 m)

Cleaning cloth

Speed clamp x 3

AA size battery x 2

(Manganese battery)

Speaker cushion x 3

(Use when installing the optional speakers at

the bottom of the Plasma Display.)

Bead band x 3

Power cord

Noise filter

Cable tie

Power cord

05 Part Names

12

En

Plasma Display

1 POWER button

2 STANDBY indicator

3 POWER ON indicator

4 Remote control sensor

1

2

4

3

5

6

7

8

(right view)

Front view

5 STANDBY/ON button

6 INPUT button

7 VOLUME +/– buttons

8 CHANNEL +/– buttons

0

9

-

=

Rear view

9 SYSTEM CABLE terminal (BLACK)

0 SYSTEM CABLE terminal (WHITE)

- SPEAKER (right/left) terminals

= AC INLET terminal

The terminals have faced downward.

05Part Names

English

13

En

Media Receiver

Front view

1 POWER button

2 POWER ON indicator

3 STANDBY indicator

4 INPUT 4 terminal (S-VIDEO)

5 INPUT 4 terminal (VIDEO)

6 INPUT 4 terminals (AUDIO)

7 PC INPUT terminal (AUDIO)

8 PC INPUT terminal (ANALOG RGB)

POWER

ON STANDBY

LR

12

3

5

4

6

78

Pull this section to open the door.

05 Part Names

14

En

Rear view

SERVICE ONLY

ANT

INPUT 1

INPUT 3

HDMI

INPUT 2

MONITOR

OUTPUT

CONTROL

IN OUT

AC INLET

BLACK

WHITE

SYSTEM CABLE

Y

P

B

P

B

P

R

P

R

S-VIDEO

VIDEO

R-AUDIO-L

S-VIDEO

VIDEO

R-AUDIO-L

COMPONENT VIDEO

^*(=~ ! @ # $ %

67890 -23145

&

1 Antenna input terminal

2 RS-232C terminal (used for factory setup)

3 Control input terminal

4 Control output terminal

5 INPUT 2 terminal (VIDEO)

6 INPUT 2 terminals (AUDIO)

7 INPUT 1 terminal (S-VIDEO)

8 INPUT 1 terminal (VIDEO)

9 INPUT 1 terminals (AUDIO)

0 INPUT 1 COMPONENT VIDEO terminals

(Y, PB, PR)

- AC INLET terminal

= INPUT 2 terminal (S-VIDEO)

~ MONITOR OUTPUT terminal (S-VIDEO)

! MONITOR OUTPUT terminal (VIDEO)

@ MONITOR OUTPUT terminals (AUDIO)

# INPUT 3 terminal (S-VIDEO)

$ INPUT 3 terminal (VIDEO)

% INPUT 3 terminals (AUDIO)

^ INPUT 3 COMPONENT VIDEO terminals

(Y, PB, PR)

& INPUT 3 terminal (HDMI)

* SYSTEM CABLE terminal (WHITE)

( SYSTEM CABLE terminal (BLACK)

05Part Names

English

15

En

Remote control unit

1 a

Turns on the power to the Plasma Display or

places it into standby mode.

2 INPUT 1, 2, 3, 4

Selects an input source.

3 PC

Selects the PC terminal as an input source.

4 c

Switches the screen mode among 2-screen,

picture-in-picture, and single-screen.

5 0 – 9

Switches on the power to the Plasma Display.

TV/External input mode: Selects a channel.

TELETEXT mode: Selects a page.

6 p

Displays the channel information.

7 P +/P –

TV/External input mode: Selects a channel.

w/x

TELETEXT mode: Selects a page.

8

g

Sets the sound multiplex mode.

9

(RETURN)

Restores the previous menu screen.

0

/ / /

Selects a desired item on the setting screen.

- Color (RED/GREEN/YELLOW/BLUE)

TELETEXT mode: Selects a page.

= k

TELETEXT mode: Displays hidden characters.

~ f

TV/External input mode: Changes the wide

screen size.

v

TELETEXT mode:

Switches Teletext images.

(full/upper half/lower half)

! d

Freezes a frame from a moving image. Press

again to cancel the function.

TELETEXT mode: Stops updating Teletext pages.

Press again to release the hold mode.

@ CH ENTER

Executes a channel number.

# i +/i –

Sets the volume.

$ e

Mutes the sound.

% HOME MENU

TV/External Input mode: Displays the Menu

screen.

^ ENTER

Executes a command.

& m

Selects the TELETEXT mode.

(all TV image, all TEXT image, TV/TEXT

image)

* l

TELETEXT mode:

Displays an Index page for the

CEEFAX/FLOF format. Displays a TOP Over View

page for the TOP format.

• When using the remote control unit, point it at the

Plasma Display.

3

4

6

7

8

0

-

=

9

5

2

1

%

$

&

*

^

#

@

!

~

06 Preparation

16

En

Installing the Plasma Display

Locating

• Avoid direct sunlight. Maintain adequate ventilation.

• The length of the system cable used to connect the

Plasma Display and the Media Receiver is about 3 m.

• Because the Plasma Display is heavy, be sure to have

someone help you when moving it.

• If you place anything on the top of the Media Receiver

it will not receive enough ventilation and will not

operate properly.

• Allow enough space around the upper and back parts

when installing to ensure ventilation around the

backside.

Using the optional PIONEER stand

•For details on installation, refer to the instruction

manual provided with the stand.

Using the optional PIONEER speakers

•For details on installation, refer to the instruction

manual provided with the speaker.

Operating Environment

Operating environment temperature and humidity:

+0°C to +40°C; less than 85% RH (cooling vents not

blocked)

Avoid installing in the following locations:

• Under direct exposure to sunlight

• Under strong artificial light

• In high humidity

•Poorly ventilated

Over 50 cm

Over

10 cm

Allowed operation range of the remote

control unit

Operate the remote control unit while pointing it toward

the remote control sensor (t) located at the bottom

right of the front panel of the Plasma Display. The

distance from the remote control sensor must be within

7 m and the angle relative to the sensor must be within

30 degrees in the right or left direction.

When the remote control unit does not func-

tion properly

• When any obstacle exists between the remote control

unit and the remote control sensor, the remote

control unit may not function.

• As the batteries become empty, the remote control

unit can function within a shorter distance from the

remote control sensor. Replace the batteries with new

ones early enough.

• The Plasma Display emits very weak infrared rays

from its screen. If you place such equipment oper-

ated through infrared remote control as a VCR

nearby, that equipment may not receive commands

from its remote control unit properly or entirely. If this

is the case, place that equipment at a location far

enough from the Plasma Display.

• Depending on the installation environment, infrared

rays from the Plasma Display may not allow this

system to properly receive commands from the

remote control unit or may shorten allowable dis-

tances between the remote control unit and the

remote control sensor. The strength of infrared rays

emitted from the screen differs, depending on images

displayed on the screen.

7 m

30º

Remote

control

sensor

06Preparation

English

17

En

POWER

ON STANDBY

POWER

ON STANDBY

Installing the Media Receiver

POWER

ON STANDBY

Plasma Display

Media Receiver

(vertical installation)

(horizontal installation)

System cable

(approx. 3 meters)

• Do not place a VCR or any other device on top of

the Media Receiver.

• When installing, allow enough space on the

sides and above the Media Receiver.

• Do not block the cooling vent on any side of the

Media Receiver or the rear ventilation fan open-

ing of the Media Receiver.

Over 10 cm

Over 5 cm

POWER

ON STANDBY

Over 5 cmOver 5 cm

Over 5 cm

Over 10 cm

06 Preparation

18

En

Installing the Media Receiver vertically

You can use the accompanying stand to install the

Media Receiver vertically.

Installing the Media Receiver vertically

Insert the vertical installation stand into the side of the

Media Receiver.

Secure the vertical installation stand with

screws.

Vertical installation stand

screws

You can remove the shock absorbing pads.

Keep the shock absorbing pads and screws. They are

required when you place the Media Receiver in the

horizontal position.

Plug the screw holes using the caps provided.

• When you have installed the Media Receiver

vertically, always use the accompanying stand.

If you place the unit directly on the floor the

cooling vents will be blocked which will result in

mechanical failure.

Remove the separation sheet.

Screw hole cap

Align with the

hole and attach.

Right side

Shock absorbing pad

06Preparation

English

19

En

SERVICE ONLY

ANT

INPUT 1

INPUT 3

HDMI

INPUT 2

MONITOR

OUTPUT

CONTROL

IN OUT

BLACK

WHITE

SYSTEM CABLE

Y

PB

PR

S-VIDEO

VIDEO

R-AUDIO-L

S-VIDEO

VIDEO

R-AUDIO-L

COMPONENT VIDEO

INPUT 3

AC INLET

Setting the system

Connecting the system cable to the Plasma Display

• THESE SPEAKER TERMINALS CAN BE APPLIED WITH HAZARDOUS VOLTAGE WHEN YOU

CONNECT OR DISCONNECT THE SPEAKER CABLES, TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT TOUCH UNINSULATED PARTS BEFORE DISCONNECTING THE POWER CORD.

Connecting the system cable to the Media Receiver

For details on optional PIONEER

speaker installation, refer to the

speaker instruction manual

provided.

Plasma Display (rear view)

(WHITE)

(BLACK)

System cable

Media Receiver (rear view)

(WHITE)

(BLACK)

06 Preparation

20

En

Routing cables

Speed clamps and bead bands are included with this system for bunching cables. Once properly bunched, follow

the steps below to route the cables.

When the speakers are installed on the sides

When the speakers are installed at the bottom

(rear view)

Cable binders (supplied

with the stand)*

Attaching speed clamps to the main unit

Attach the speed clamps using the 4 holes marked with

below, depending on your routing system.

Attaching and removing speed clamps

Insert 1 into an appropriate hole on the rear of the

Plasma Display and snap 2 into the back of 1 to lock

the clamp.

Speed clamps are designed to be difficult to undo once

in place. Please attach them carefully.

Use pliers to twist the clamp 90°, pulling outward. The

clamp may deteriorate over time and become damaged

if removed.

1

2

Speaker cable Speed clamps

Speaker cable Speaker cable

Cable binders (supplied

with the stand)*

Speaker cable

* Cable binder

Using the cable binders supplied with the stand, put the

speaker and system cables together so that the cables are

invisible from the front. At that time be careful not to apply

any force to the connection sections of the cables.

ページが読み込まれています...

Pioneer PDP-435HDG ユーザーマニュアル

このマニュアルも適しています

Pioneer PDP-435HDG ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント