Pioneer PDP-607CMX ユーザーマニュアル

PDP-507CMX

PDP-607CMX

Plasma Display

Écran à plasma

Operating Instructions

Mode d’emploi

Contents related to system specifications, power requirements,

accessories, and other information differ with respect to the

country where this unit is purchased. For customers living in the

U.S.A. or Canada, please use and refer to the instructions written

in either English or French. For customers in Japan, please use

and refer to the instructions written in Japanese.

Les caractéristiques, les spécifications d'alimentation, les

accessoires et d'autres informations diffèrent d'un pays à

l'autre. Si vous vivez au Canada ou aux États-Unis, reportez-

vous aux instructions en français ou en anglais. Si vous vivez

au Japon, reportez-vous aux instructions en japonais.

English

This unit has been designed for use as a computer display monitor.

The optional video card is required if you wish to view other video

signals on the monitor. For details consult your local retail dealer.

Français

Cet appareil est conçu pour une utilisation comme moniteur d’affichage

d’ordinateur.

La carte vidéo optionnelle est nécessaire si vous souhaitez regarder

d’autres signaux sur ce moniteur. Pour plus de renseignements,

consultez votre revendeur.

i

En

Safety Precautions

Français

English

Operating Instructions

Thank you very much for purchasing this PIONEER product.

Before using your Plasma Display, please read the “Safety

Precautions” and these “Operating Instructions” carefully

so you will know how to operate the Plasma Display properly.

Keep this manual in a safe place. You will find it useful in

the future.

Notes on Installation Work:

This product is marketed assuming that it is installed by qualified

personnel with enough skill and competence. Always have an

installation specialist or your dealer install and set up the product.

PIONEER cannot assume liabilities for damage caused by

mistake in installation or mounting, misuse, modification or a

natural disaster.

Note for Dealers:

After installation, be sure to deliver this manual to the customer

and explain to the customer how to handle the product.

ii

En

English

Safety Precautions

IMPORTANT NOTICE

The serial number for this equipment is located on the rear

panel. Please write this serial number on your enclosed

warranty card and keep it in a secure area. This is for your

security.

The following symbols are found on labels

attached to the product. They alert the operators

and service personnel of this equipment to any

potentially dangerous conditions.

i

CAUTION: WHEN POSITIONING THIS EQUIPMENT

ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY

ACCESSIBLE.

D3-4-2-1-1_En-A

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

WARNING

This equipment is not waterproof. To prevent a fire

or shock hazard, do not place any container filed

with liquid near this equipment (such as a vase or

flower pot) or expose it to dripping, splashing, rain

or moisture.

D3-4-2-1-3_A_En

WARNING

This symbol refers to a hazard or unsafe

practice which can result in personal injury

or property damage.

CAUTION

This symbol refers to a hazard or unsafe

practice which can result in severe personal

injury or death.

WARNING:

Handling the cord on this product or

cords associated with accessories sold with the

product will expose you to chemicals listed on

proposition 65 known to the State of California and

other governmental entities to cause cancer and

birth defect or other reproductive harm.

D36-P4_A_En

Wash hands after handling

iii

En

Safety Precautions

Français

English

Safety Precautions

ii

CAUTION: When changing batteries, use only conventional non-rechargeable alkaline or manganese batteries (2).

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the institutions.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_En

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate

the equipment.

D8-10-2_En

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the

unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and

televisions, use shielded cables and connectors for connections.

D8-10-3a_En

iv

En

English

Safety Precautions

iii

FEDERAL COMMUNICATIONS COMMISSION

DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Product Name: Plasma Display with Video Card

Model Number: PDP-507CMX/PDP-607CMX (Plasma Display)

PDA-5003/PDA-5004 (Video Card)

Product Category: Class B Personal Computers & Peripherals

Responsible Party Name: PIONEER ELECTRONICS SERVICE, INC.

Address: 1925E. Dominguez st., Logn Beach, CA. 90801-1760, U.S.A.

Phone Number: 800-421-1625

For Business Customer URL: http://www.pioneerelectronics.com

Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer

Authorized Independent Service Company, or if you wish to purchase replacement parts,

operating instructions, service manuals, or accessories, please call the number shown

below.

8 0 0 – 4 2 1 – 1 6 2 5

Please do not ship your product to Pioneer without first calling the Customer Support

Division at the above listed number for assistance.

Pioneer Electronics (USA) Inc.

Customer Support Division

P.O. BOX 1760, Long Beach,

CA 90801-1760, U.S.A.

For warranty information please see the Limited Warranty sheet included with your product.

Should this product require service in Canada, please contact a Pioneer Canadian

Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada.

Alternatively, please contact the Customer Satisfaction Department at the following address:

Pioneer Electronics of Canada, Inc.

Customer Satisfaction Department

300 Allstate Parkway, Markham, Ontario L3R OP2

(905)479-4411

1(877)283-5901

For warranty information please see the Limited Warranty sheet included with your product.

1

En

Contents

English

Contents

Safety Precautions ................................... i

Features ................................................... 2

Before Proceeding ................................... 3

How to use this manual...................................... 3

Checking supplied accessories .......................... 5

Part Names and Functions ..................... 6

Main unit.............................................................. 6

Remote control unit ............................................ 7

Connection panel (PDP-507CMX) ...................... 9

Connection panel (PDP-607CMX) .................... 10

Installation and Connections ............... 11

Installation of the unit....................................... 11

Connection to a personal computer ................ 13

Audio connections ............................................ 14

Power cord connection..................................... 15

How to route cables .......................................... 16

System Settings .................................... 17

Setting the onscreen display language........... 17

Settings after connections ............................... 18

Operation ............................................... 19

Selecting input source ...................................... 19

Adjusting sound volume .................................. 20

Muting the sound.............................................. 20

Confirming current status ................................ 20

Changing screen size ........................................ 21

Enlarging one part of the screen

(POINT ZOOM) .................................................. 22

Multiscreen display........................................... 23

Automatic power-off

(POWER MANAGEMENT) ................................ 24

PICTURE/SCREEN Adjustment ............ 25

PICTURE adjustment ........................................ 25

Adjusting screen POSITION, CLOCK,

and PHASE

<automatic adjust> ....................... 26

Adjusting screen POSITION, CLOCK,

and PHASE

<manual adjust> ........................... 27

Other Operations .................................. 29

Setting the ORBITER ......................................... 29

Setting the SOFT FOCUS ................................. 30

Energy saving settings (ENERGY SAVE) ......... 31

Automatic input switching

(AUTO FUNCTION) ........................................... 32

Setting the PRESENT TIME .............................. 33

Activating the timer .......................................... 34

Setting the subscreen mode (PIP DETECT) .... 35

Setting the memo screen (SPLIT FREEZE)...... 36

Additional Information ......................... 37

Cleaning ............................................................. 37

Troubleshooting ................................................ 38

Precautions regarding use ............................... 40

STANDBY/ON indicator .................................... 40

Specifications .................................................... 41

Appendix 1: Computer signal

compatibility table ............................................ 42

Appendix 2: INPUT1/2 pin assignments ......... 45

Explanation of terms ........................................ 46

2

En

Features

English

¶ Optional line (sold separately)

(For details, please consult the dealer where this unit was

purchased.)

1 Table top stand: Display stand.

2 Wall installation unit:

Wall installation bracket designed as a wall

interface for securing the unit.

3

Speaker system designed specifically for Plasma Displays

(width: 9 cm (3-9/16 in.)): 2-way speaker units featuring 5 cm

(2 in.) tweeter and 8 cm (3-3/16 in.) woofer in

vertical arrangement.

4 Video card: Expansion card allows viewing of video signals

and computer analog RGB signals.

Cards used in the expansion slots should be

manufactured or recommended by Pioneer.

Using other expansion cards may result in

malfunction.

¶ Introduces newly developed Wide Plasma Panel

The new wide high-precision plasma panel (1365x768 / 16:9)

pushes the envelope of previous high-luminance panels,

producing brighter, clearer images with higher contrast.

¶ ES Slot interface for enhanced potential

The display is provided with a built-in ES Slot Interface to allow

the installation of cards for the connection of external devices,

thus enhancing its expansion potential.

¶ Supports wide range of computer signals (analog/

digital)

Supports non-compressed display of signals ranging from

640x400 and 640x480 (VGA) to 1024x768 (XGA), and

compressed display of 1280x1024 (SXGA), 1400x1050 (SXGA+)

and 1600x1200 (UXGA) signals. Further, aspect ratio and screen

size settings supported include [DOT BY DOT], [4:3] and [FULL]

(*1).

* Supported signals are different on INPUT1 and INPUT2.

*1 Aspect ratio and screen size appearance will differ depending

on input signal.

¶ Free Installation Configuration

– Broader installation possibilities with thinner,

lighter, high-endurance design –

PDP-507CMX:

While producing a large 50" screen image, the display is only

99 mm thick, and weighs in at only 35.5 kg.

PDP-607CMX:

While producing a large 60" screen image, the display is only 122

mm thick, and weighs in at only 61.5 kg.

On the other hand, the efficient heat-radiating design greatly

improves environmental operating conditions. The thinner, lighter

design, coupled to high-endurance construction greatly broadens

the range of possible installation locations and styles.

¶ High reliability for commercial applications

This display is provided with features giving it high dependability

in commercial applications, including the ability to suppress peak

luminance in accordance with the viewing program, and to

change the cooling fan’s speed in accordance with changes in

operating environment. Such features provide safety and high-

endurance under conditions of commercial use.

¶ Improved usability

User convenience has been improved by the inclusion of

features making the display even more compatible with your

computer. Some of these include the one-touch screen

adjustment, [AUTO SET UP] function for computer connections,

and the POINT ZOOM function to enlarge local portions of the

screen image to display important detailed program data.

¶ Power-Saving Design

The display is provided with a variety of power-saving functions,

including an automatic brightness function with ambient light

sensor.

Features

3

En

Before Proceeding

English

Before Proceeding

How to use this manual

This manual is set up to follow the course of actions and

operations in the order that would seem most logical for

someone setting up this unit.

Once the unit has been taken out of the box and it has

been confirmed that all the parts have been received

(page 5), it may be beneficial to look over the section

“Part Names and Functions” starting on page 6 to

become acquainted with the plasma monitor and remote

control unit, as their respective buttons and controls will

be referred to throughout this manual.

The section “Installation and Connections” starting on

page 11 covers all the necessary points regarding

installation of the Plasma Display and connections to a

wide variety of components.

The section “System Settings” starting on page 17

covers the on-screen settings necessary for correct

operation of the Plasma Display with its connected

components. Depending on the connections made, this

section may or may not be necessary.

The remainder of the sections in this manual is dedicated

to the basic operations associated with selecting a source

component up to the more complex operations

associated with adjusting the Plasma Display picture to

match the requirements of specific components and

personal preferences.

Menu display examples

SCREEN SETUP OPTION

:

0

:

0

:

0

CONTRAST

:

0

BRIGHTNESS

H.ENHANCE

V.ENHANCE

PICTURE RESET

PICTURE

MENU INPUT1

ENTER

SET

EXIT

MENU

Images shown here may differ from the actual display

image.

4

En

Before Proceeding

English

About operations in this manual

Each operation is described in its proper operating order.

These Operating Instructions will refer to the operating

controls found on the remote control unit, with the

exception of those buttons found only on the main

Plasma Display itself. When the Plasma Display controls

include equivalent buttons to those found on the remote

control unit, the commands can be performed on the

main unit as well.

The following illustrations are an example of the actual

operations used for the section “PICTURE adjustment”.

The examples are provided to allow you to confirm

whether the operation is performed correctly or not.

Before Proceeding

Note

The screen images depicted in these Operating Instructions

should be considered typical images; some difference will be

seen in practice, depending on the screen item displayed and its

contents, the input source and various other control settings.

5

En

Before Proceeding

English

Checking supplied accessories

Check that the following accessories were supplied.

1 Power cord (2 m/6.6 feet)

2 Remote control unit

3 AA (R6) batteries (x 2)

4 Cleaning cloth (for screen)

5 Speed clamps (x 3)

6 Bead bands (x 3)

Before Proceeding

7 Ferrite cores (x 3) (for audio cables)

÷ These Operating Instructions

÷ Warranty

6

En

Part Names and Functions

English

4

STANDBY

ON

STANDBY/ON MENU

DISPLAY

/ SET

– VOL +INPUT SCREEN SIZE



6 7 8 95

2

3

1

13

0

Part Names and Functions

Main unit

1 Remote control sensor

Point the remote control toward the remote sensor to

operate the unit (page 8).

2 Ambient light sensor (PDP-507CMX)

This sensor measures the level of light inside the

viewing room; it is enabled when the [ENERGY

SAVE] option is set to [AUTO] (page 31).

3 STANDBY/ON indicator

When the unit is operating:

The indicator lights green (page 19).

When flashing, the indicator is used to indicate error

messages (page 40).

The indicator flashes green once every one second

when the [POWER MGT.] function is operating (page

24).

When the unit is in standby mode:

The indicator lights red (page 19).

When flashing, the indicator is used to indicate error

messages (page 40).

4 Handles

Operation panel on the main unit

5 STANDBY/ON button ( )

Press to put the display in operation or standby mode

(page 19).

6 MENU button

Press to open and close the on-screen menu (pages

17 to 36).

7 DISPLAY/SET button

Use to confirm onscreen menu selections, and to

change settings (pages 17 to 36).

When not indicated by onscreen menus, used to

display the current set status (page 20).

8 INPUT (’) button

Except when menu screen is displayed, this button

operates to change the input.

9 SCREEN SIZE (‘ ) button

Except when menu screen is displayed, this button

operates to change the screen size.

0 VOL +/– (}/]) buttons

When not indicated for use in onscreen menu items,

these buttons are used for adjusting the sound

volume (pages 19 and 20).

Main unit

Operation panel on the

main unit

PDP-507CMX

PDP-607CMX

(PDP-507CMX)

(PDP-607CMX)

7

En

Part Names and Functions

English

-

=

0

~

!

#

%

$

2

3

7

@6

8

9

1

5

4

Remote control unit

When handling the remote control unit

¶ Do not drop the remote control unit or expose it to

moisture.

¶ Do not use the remote control unit in a location subject to

direct sunlight, heat radiation from a heater, or in a place

subject to excessive humidity.

¶ When the remote control unit’s batteries begin to wear out,

the operable distance will gradually become shorter. When

this occurs, replace all batteries with new ones as soon as

possible.

5 SET button

Press to adjust or enter various settings on the unit

(pages 17 to 36).

6 SUB INPUT button

During multi-screen display, use this button to change

inputs to subscreens (page 23).

7 SPLIT button

Press to switch to multi-screen display (page 23).

8 MUTING button

Press to mute the volume (page 20).

9 ID NO. SET button

Button used by professional installers.

0 AUTO SET UP button

When using computer signal input, automatically sets

the [POSITION], [CLOCK] and [PHASE] to optimum

values (page 26).

- STANDBY/ON button ( )

Press to put the unit in operation or standby mode

(page 19).

= DISPLAY button

Press to view the unit’s current input and setup mode

(page 20).

~ POINT ZOOM button

Use to select and enlarge one part of the screen (page

22).

! FREEZE button

When memo screen function is enabled, a still image

is displayed in the subscreen (page 36).

@ SWAP button

During multi-screen display, use this button to switch

between main screen and subscreen (page 23).

# PIP SHIFT button

When using the picture-in-picture mode with multi-

screen display, use this button to move the position of

subscreen (page 23).

$ VOLUME (+/–) buttons

Use to adjust the volume (pages 19 and 20).

% CLEAR button

Button used by professional installers.

Part Names and Functions

1 SCREEN SIZE button

Press to select the screen size (page 21).

2 INPUT buttons

Press to select the input (page 19).

3 MENU button

Press to open and close the on-screen menu

(pages 17 to 36).

4 ADJUST (5/∞/3/2) buttons

Use to navigate menu screens and to adjust various

settings on the unit (pages 17 to 36).

8

En

Part Names and Functions

English

Part Names and Functions

30°

If you are having difficulty with operation of

the remote control unit

¶ The remote control unit may not operate if there are

objects placed between it and the display.

¶ Operational distance will gradually become shorter as the

batteries begin to wear out, replace weak batteries with

new ones as soon as possible.

¶ This unit discharges infrared rays from the screen. Placing a

video deck or other component that is operated by an

infrared remote control unit near this unit may hamper that

component’s reception of the remote control’s signal, or

prevent it from receiving the signal entirely. Should this

occur, move the component to a position further away from

this unit.

¶ Depending on the installation surroundings, this unit’s

remote control unit may be influenced by the infrared rays

discharged from the Plasma Display, hampering reception

of its rays or limiting its operational distance. The strength

of infrared rays discharged from the screen will differ

according to the picture displayed.

Operating range of the remote

control unit

When operating the remote control unit, point it at the

remote sensor located on the front panel of the main

unit. The remote control unit is operable up to 7 m from

the unit and within a 30 angle on each side of the

sensor.

Inserting the batteries in the

remote control unit

Designated batteries

Please use size AA (R6) or AA (LR6).

CAUTION

¶ Do not use batteries other than those designated, and do

not mix old and new batteries together, since rupture or

leakage may result, leading to danger of fire, personal

injury, or contamination.

¶ When loading batteries into the remote control unit, insert

the batteries with (+) and (–) polarities matching those

indicated in the diagram. Inserting batteries incorrectly

may result in battery rupture or leakage, leading to danger

of fire, personal injury, or contamination.

¶ Do not heat or disassemble batteries, and do not dispose

of batteries in fire or water, since battery rupture or leakage

may result, leading to danger of fire or personal injury.

¶ When not using the remote control unit for extended

periods of time, remove the batteries and store them

separately. Leaving batteries unused in the unit may

result in battery leakage, leading to danger of fire,

personal injury, or contamination.

When disposing of used batteries, please comply

with governmental regulations or

environmental public institution’s rules that

apply in your country/area.

D3-4-2-3-1_En

While pressing down lightly, slide

in the direction of the arrow.

Two AA (R6)

batteries

7 m

(23 feet)

Remote Sensor

9

En

Part Names and Functions

English

COMBINATION

IN OUT

RS-232C

AUDIO AUDIO

INPUT1

AUDIO

OUTPUT INPUT2

ANALOG RGB OUT

(D-Sub)

ANALOG RGB IN

(D-Sub)

INPUT1

DIGITAL RGB

(DVI-D)

INPUT2

4

=-

21 8 9 03567

1 SPEAKER (R) terminal

For connection of an external right speaker.

Connect a speaker that has an impedance of 6 Ω

(page 14).

2 SPEAKER (L) terminal

For connection of an external left speaker. Connect a

speaker that has an impedance of 6 Ω (page 14).

3 COMBINATION IN/OUT

Never connect any component to these

connectors without first consulting your Pioneer

installation technician.

These connectors are used for Plasma Display setup

adjustments.

4 RS-232C

Never connect any component to this connector

without first consulting your Pioneer installation

technician.

This connector is used for Plasma Display setup

adjustments.

5 AUDIO (OUTPUT) (Stereo mini jack)

Use to output the audio of the selected source

component connected to this unit to an AV amplifier

or similar component.

Note: No sound is produced from the AUDIO (OUTPUT) jack

when the MAIN POWER switch is set to OFF or ON (standby)

(page 14).

6 AUDIO (INPUT1) (Stereo mini jack)

Use to obtain sound when INPUT1 is selected.

Connect the audio output jack of components

connected to INPUT1 to this unit (page 14).

Connection panel (PDP-507CMX)

The connection panel is provided with two video input

terminals and one video output terminal. Audio input/

output and speaker output terminals are also provided.

For instructions regarding connections, consult the pages

noted in parentheses by each item.

7 AUDIO (INPUT2) (Stereo mini jack)

Use to obtain sound when INPUT2 is selected.

Connect the audio output jack of components

connected to INPUT2 to this unit (page 14).

8 ANALOG RGB OUT (INPUT1) (mini D-sub 15 pin)

Use the ANALOG RGB OUT (INPUT1) terminal to

output the video signal to an external monitor or other

component.

Note: The video signal will not be output from the ANALOG

RGB OUT (INPUT1) terminal when the main power of this

unit is off or in standby mode.(page 13)

9 ANALOG RGB IN (INPUT1) (mini D-sub 15 pin)

For connection of a personal computer (PC) or similar

component. Make sure that the connection made

corresponds to the format of the signal output from

the connected component (page 13).

0 DIGITAL RGB (INPUT2) (DVI-D jack)

Use to connect a computer.

Note: This unit does not support the display of

copyguard-protected video signals (page 13).

- AC IN

Use to connect the supplied power cord to an AC

outlet (page 15).

= MAIN POWER switch

Use to switch the main power of the unit on and off.

Part Names and Functions

10

En

Part Names and Functions

English

COMBINATION

IN OUT

RS-232C

AUDIO AUDIO

INPUT1

AUDIO

OUTPUT INPUT2

ANALOG RGB OUT

(D-Sub)

ANALOG RGB IN

(D-Sub)

INPUT1

DIGITAL RGB

(DVI-D)

INPUT2

0432158967

=-

Part Names and Functions

1 COMBINATION IN/OUT

Never connect any component to these

connectors without first consulting your Pioneer

installation technician.

These connectors are used for Plasma Display setup

adjustments.

2 SPEAKER (R) terminal

For connection of an external right speaker.

Connect a speaker that has an impedance of 6 Ω

(page 14).

3 SPEAKER (L) terminal

For connection of an external left speaker. Connect a

speaker that has an impedance of 6 Ω (page 14).

4 RS-232C

Never connect any component to this connector

without first consulting your Pioneer installation

technician.

This connector is used for Plasma Display setup

adjustments.

5 AUDIO (OUTPUT) (Stereo mini jack)

Use to output the audio of the selected source

component connected to this unit to an AV amplifier

or similar component.

Note: No sound is produced from the AUDIO (OUTPUT) jack

when the MAIN POWER switch is set to OFF or ON (standby)

(page 14).

Connection panel (PDP-607CMX)

The connection panel is provided with two video input

terminals and one video output terminal. Audio input/

output and speaker output terminals are also provided.

For instructions regarding connections, consult the pages

noted in parentheses by each item.

6 AUDIO (INPUT1) (Stereo mini jack)

Use to obtain sound when INPUT1 is selected.

Connect the audio output jack of components

connected to INPUT1 to this unit (page 14).

7 AUDIO (INPUT2) (Stereo mini jack)

Use to obtain sound when INPUT2 is selected.

Connect the audio output jack of components

connected to INPUT2 to this unit (page 14).

8 ANALOG RGB OUT (INPUT1) (mini D-sub 15 pin)

Use the ANALOG RGB OUT (INPUT1) terminal to

output the video signal to an external monitor or other

component.

Note: The video signal will not be output from the ANALOG

RGB OUT (INPUT1) terminal when the main power of this

unit is off or in standby mode.(page 13)

9 ANALOG RGB IN (INPUT1) (mini D-sub 15 pin)

For connection of a personal computer (PC) or similar

component. Make sure that the connection made

corresponds to the format of the signal output from

the connected component (page 13).

0 DIGITAL RGB (INPUT2) (DVI-D jack)

Use to connect a computer.

Note: This unit does not support the display of

copyguard-protected video signals (page 13).

- AC IN

Use to connect the supplied power cord to an AC

outlet (page 15).

= MAIN POWER switch

Use to switch the main power of the unit on and off.

11

En

Installation and Connections

Français

English

Installation and Connections

Installation of the unit

Installation using the optional PIONEER stand or

other mounting brackets

÷ Please be sure to request installation or mounting of this unit

by an installation specialist or the dealer where purchased.

CAUTION

÷ Use only those stands or mounting brackets designated by

Pioneer. If other non-recommended products are used, the

unit may fall and be damaged or otherwise malfunction.

÷ Assemble stands or mounting brackets correctly in accordance

with the instructions provided or other applicable installation

instructions.

÷ Two or more people should always work together when

installing or removing this unit.

÷ The installation location selected should be fully capable of

supporting the weight of this unit, and be a stable, flat, and

even surface. If installed in other locations, the unit may fall or

be damage.

÷ After installation, take appropriate measures to prevent the

installation from falling. The failure to take such measures

could allow the unit to fall, causing injuries or damage.

Wall-mount installation of the unit

This unit has been designed with bolt holes for

wall-mount installation, etc. The installation holes

provided are shown in the accompanying illustration.

÷ Be sure to attach in 4 or more locations above and

below, left and right of the center line.

÷ Use bolts that are long enough to be inserted 12 mm

(

1

/2 in.) to 18 mm (

11

/16 in.) into the main unit from the

attaching surface for both a holes and b holes. Refer to

the side view diagram in the accompanying illustration.

÷ As this unit is constructed with glass, be sure to install

it on a flat, unwarped surface.

CAUTION

When this unit is installed on a wall, the work should be done by

a professional technician possessing the requisite technical

knowledge and abilities; consult your dealer for more

information. Improper or insufficient installation may result in

accidents, damage or personal injury.

CAUTION

÷ Handles should not be removed or reattached by anyone other

than the professional installation technician or service

personnel.

÷ When moving the display, it should always be carried by two

persons holding the rear handles in the manner shown.

Never attempt to move the Plasma Display by holding only

one of the handles.

12

En

Installation and Connections

English

Main unit

a hole

b hole

Bolt

Attaching surface

Installation

bracket, etc.

12 mm to 18 mm

(

1

/

2

in. to

11

/

16

in.)

12 mm to 14 mm

(

1

/2 in. to

9

/16 in.)

Side view diagram

Installation and Connections

b hole*

Center line

b hole*b hole*

b hole*

Center line

Rear view diagram (PDP-507CMX)

a hole

Air vents (fan)

b hole*

Center line

b hole*

Center line

Rear view diagram (PDP-607CMX)

a hole

Air vents (fan)

a hole

* Only for speaker unit

13

En

Installation and Connections

Français

English

Installation and Connections

Connection to a personal computer

Connection method differs depending on the computer

type. When connecting, please thoroughly read the

computer’s instruction manual.

Before making connections, be sure to make sure that

the personal computer’s power and this unit’s main

power is off.

Connection to INPUT1

Connect the display’s D-sub input connector to the D-sub

output (analog RGB) from the computer.

This connector also supports G ON SYNC (output with

green signal combined with sync signal), and composite

SYNC (output with combined horizontal and vertical sync

signals).

When connecting to ANALOG RGB IN (INPUT1)

ANALOG RGB OUT

(D-Sub)

ANALOG RGB IN

(D-Sub)

INPUT1

Connect the cable corresponding to the shape of the

input terminal on this unit and the personal computer’s

output terminal.

Secure by tightening the terminal screws on both units.

Following completing connections, on-screen setup is

necessary. See pages 17 to 18 for details.

Note

Depending on the type of computer model being connected, a

conversion connector or adapter etc. provided with the computer

or sold separately may be necessary.

For details, please read your PC’s instruction manual or consult

the maker or nearest dealer of your computer.

NOTICE

¶ INPUT1 supports Microsoft “Plug & Play” (VESA DDC 1/2B)

components. See Appendix 2-1/2 (page 45) when making

connections to INPUT1.

¶ See Appendix 1 (pages 42 to 43) for information regarding

signals and display formats supported by INPUT1.

To an external monitor

When connecting to ANALOG RGB OUT (INPUT1)

ANALOG RGB OUT

(D-Sub)

ANALOG RGB IN

(D-Sub)

INPUT1

With this unit, it is possible to output the video signal to

an external monitor or other component from the

ANALOG RGB OUT (INPUT1) terminal.

Note

A video signal will not be output from the ANALOG RGB OUT

(INPUT1) terminal when the main power of this unit is off or in

standby.

Connection to INPUT2

A computer equipped with DVI output (digital RGB signal)

can be connected to the Plasma Display’s DVI connector.

DIGITAL RGB

(DVI-D)

INPUT2

Following completing connections, on-screen setup is

necessary. See pages 17 to 18 for details.

Notes

¶ Use a DVI-D 24-pin (digital only) cable for the connection.

¶ This unit does not support the display of copyguard-protected

video signals.

NOTICE

¶ INPUT2 supports Microsoft “Plug & Play” (VESA DDC 2B)

components. See Appendix 2-2/2 (page 45) when making

connections to INPUT2.

¶ See Appendix 1 (pages 43 to 44) for information regarding

signals and display formats supported by INPUT2.

14

En

Installation and Connections

English

Installation and Connections

Audio connections

Before making connections, be sure to check that the

audio component’s power and the unit’s main power is

off.

Connecting the speakers

This unit is equipped with speaker output terminals for

connection to the speaker system (not supplied) specially

designed for use with this unit. Refer to the illustrations

below when making connections to the speaker terminals

on this unit.

12 mm

Notes

÷ After connecting the wires, pull gently on the cords to confirm

that the wire cores are fastened securely in their terminals.

Insecure connections will result in noise or interrupted sound.

÷ Do not allow the wire cores of the ª and · speaker cords to

protrude excessively, since they may touch each other,

causing a short circuit. This will produce excessive load on the

Plasma Display, causing operation to malfunction or stop.

Connection to audio output connector

Use a stereo miniplug to connect the Plasma Display’s

AUDIO (OUTPUT) stereo mini jack (L/R) to an AV amplifier

or other component.

AUDIO AUDIO

INPUT1

AUDIO

OUTPUT INPUT2

Making connections to the audio inputs on this

unit

This unit features two audio inputs and one audio output.

The following chart shows the video inputs and the

corresponding audio input terminals.

Twist exposed

wire strands

together.

Push tab to the open

position, and insert the

wire. Then, close tab

firmly to secure the wire

in place.

INPUT1

INPUT2

Audio input jacks Sound output

Stereo mini jack

(L/R)

Stereo mini jack

(L/R)

Sound of the selected video

input is output from the

• SPEAKER (L/R) terminals

• Stereo mini jack (L/R)

Video

input

Audio connections for component (computer)

connected to INPUT1

AUDIO AUDIO

INPUT1

AUDIO

OUTPUT INPUT2

A stereo miniplug cable can be used to connect the audio

output from the component connected to INPUT1, to the

Plasma Display’s AUDIO (INPUT1) stereo mini jack (L/R).

Sound is output from both the AUDIO (OUTPUT) stereo

mini jack (L/R) and the SPEAKER (L/R) terminals according

to the video input selection.

Audio connections for component (computer)

connected to INPUT2

AUDIO AUDIO

INPUT1

AUDIO

OUTPUT INPUT2

A stereo miniplug cable can be used to connect the audio

output from the component connected to INPUT2, to the

Plasma Display’s AUDIO (INPUT2) stereo mini jack (L/R).

Sound is output from both the AUDIO (OUTPUT) stereo

mini jack (L/R) and the SPEAKER (L/R) terminals according

to the video input selection.

ページを読み込んでいます...

Pioneer PDP-607CMX, PDP-507CMX, Projector Accessories PDP-507CMX ユーザーマニュアル

関連論文

その他の書類