Samsung BD-J5500 ユーザーマニュアル

カテゴリー
ブルーレイプレーヤー
タイプ
ユーザーマニュアル
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Blu-ray
Disc Player
user manual
BD-J5500
ENGLISH
Safety Information
Warning
2
•
The slots and openings in the cabinet and
in the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it
from overheating, these slots and openings
must never be blocked or covered.
- Do not place this apparatus in a confined
space, such as a bookcase, or built-
in cabinet, unless proper ventilation is
provided.
- Do not place this apparatus near or over
a radiator or heat register, or where it is
exposed to direct sunlight.
- Do not place vessels (vases etc.) containing
water on this apparatus. A water spill can
cause a fire or electric shock.
•
Do not expose this apparatus to rain or place
it near water (near a bathtub, washbowl,
kitchen sink, or pool, etc.). If this apparatus
accidentally gets wet, unplug it and contact
an authorized dealer immediately
.
• This apparatus uses batteries. In your
community, there might be environmental
regulations that require you to dispose of
these batteries properly. Please contact
your local authorities for disposal or
recycling information.
• Do not overload wall outlets, extension
cords or adaptors beyond their capacity,
since this can result in fire or electric shock.
• Route power-supply cords so that they
are not likely to be walked on or pinched
by items placed on or against them. Pay
particular attention to cords at the plug
end, at wall outlets, and the point where
they exit from the apparatus.
• To protect this apparatus from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug
it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the set due to lightning and
power line surges.
• Before connecting the AC power cord
to the DC adaptor outlet, make sure the
voltage designation of the DC adaptor
corresponds to the local electrical supply.
• Never insert anything metallic into the open
parts of this apparatus. Doing so may
create a danger of electric shock.
• To avoid electric shock, never touch the
inside of this apparatus. Only a qualified
technician should open this apparatus.
• Make sure to plug the power cord in until
it is firmly seated. When unplugging the
power cord from a wall outlet, always pull
on the power cord’s plug. Never unplug by
pulling on the power cord. Do not touch
the power cord with wet hands.
• If this apparatus does not operate normally
- in particular, if there are any unusual
sounds or smells coming from it - unplug
it immediately and contact an authorized
dealer or service center.
• Maintenance of Cabinet.
- Before connecting other components to
this product, be sure to turn them off.
- If you move your product suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and
lens and cause abnormal disc playback.
If this occurs, unplug the product, wait
for two hours, and then connect the plug
to the power outlet. Then, insert the disc,
and try to play back again.
• Be sure to pull the power plug out of the
outlet if the product is to remain unused or
if you are leaving the house for an extended
period of time (especially when children,
elderly, or disabled people will be left alone
in the house).
- Accumulated dust can cause an electric
shock, an electric leakage, or a fire by
causing the power cord to generate
sparks and heat or the insulation to
deteriorate.
•
Contact an authorized service center for
information if you intend to install your
product in a location with heavy dust, high
or low temperatures, high humidity, chemical
substances, or where it will operate 24 hours
a day such as in an airport, a train station,
etc. Failing to do so may lead to serious
damage of your product.
• Use only a properly grounded plug and wall
outlet.
- An improper ground may cause electric
shock or equipment damage. (Class l
Equipment only.)
•
To turn this apparatus off completely, you
must disconnect it from the wall outlet.
Consequently, the wall outlet and power plug
must be readily accessible at all times.
•
Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a
location safely out of the reach of children.
• Do not install the product in an unstable
location such as a shaky self, a slanted
floor, or a location exposed to vibration.
• Do not drop or strike the product. If the
product is damaged, disconnect the power
cord and contact a service center.
•
To clean this apparatus, unplug the power
cord from the wall outlet and wipe the
product using a soft, dry cloth. Do not
use any chemicals such as wax, benzene,
alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals
can damage the appearance of the product
or erase the printing on the product.
• Do not expose this apparatus to dripping
or splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
• Do not dispose of batteries in a fire.
•
Do not plug multiple electric devices into the
same wall socket. Overloading a socket can
cause it to overheat, resulting in a fire.
• There is danger of an explosion if you
replace the batteries used in the remote
with the wrong type of battery. Replace
only with the same or equivalent type.
•
WARNING - TO PREVENT
THE SPREAD OF FIRE,
KEEP CANDLES AND
OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
This symbol indicates that high volt-
age is present inside. It is dangerous
to make any kind of contact with any
internal part of this product.
This symbol indicates that important
literature concerning operation and
maintenance has been included with
this product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER (OR
BACK). THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
3
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product. Use of controls,
adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
CAUTION :
THIS PRODUCT USES AN INVISIBLE
LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE
IF DIRECTED. BE SURE TO OPERATE
PRODUCT CORRECTLY AS INSTRUCTED.
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVERS
AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
This product satisfies CE regulations when
shielded cables and connectors are used
to connect the unit to other equipment.
To prevent electromagnetic interference
with electric appliances, such as radios
and televisions, use shielded cables and
connectors for connections.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
NOTES
`
If the Region number of a Blu-ray Disc/DVDs
does not correspond to the Region number of
this product, the product cannot play the disc.
IMPORTANT NOTE
The mains lead on this equipment is supplied
with a molded plug incorporating a fuse. The
value of the fuse is indicated on the pin face of
the plug.
If it requires replacing, a fuse approved to
BS1362 of the same rating must be used.
Never use the plug with the fuse cover
omitted if the cover is detachable. If a
replacement fuse cover is required, it must be
of the same colour as the pin face of the plug.
Replacement covers are available from your
dealer.
If the fitted plug is not suitable for the power
points in your house or the cable is not long
enough to reach a power point, you should
obtain a suitable safety approved extension
lead or consult your dealer for assistance.
However, if there is no alternative to cutting
off the plug, remove the fuse and then safely
dispose of the plug. Do not connect the plug
to a mains jack, as there is a risk of shock
hazard from the bared flexible cord.
To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.
The product unit accompanying this user
manual is licenced under certain intellectual
property rights of certain third parties.
Precautions
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below.
Keep these operating instructions handy for
future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.
Do not use this apparatus near water.
6. Clean only with a dry cloth.
7.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including AV receivers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where it exits the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally, or
has been dropped.
Using the 3D function
IMPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
• Some viewers may experience discomfort
while viewing 3D TV such as dizziness,
nausea, and headaches.
If you experience any such symptom,
stop viewing 3D TV, remove the 3D Active
Glasses, and rest.
• Watching 3D images for an extended
period of time may cause eye strain. If you
feel eye strain, stop viewing 3D TV, remove
your 3D Active Glasses, and rest.
• A responsible adult should frequently check
on children who are using the 3D function.
If there are any reports of tired eyes,
headaches, dizziness, or nausea, have the
child stop viewing 3D TV and rest.
• Do not use the 3D Active Glasses for other
purposes (Such as general eyeglasses,
sunglasses, protective goggles, etc.).
• Do not use the 3D function or 3D Active
Glasses while walking or moving around.
Using the 3D function or 3D Active Glasses
while moving around may cause you to
bump into objects, trip, and/or fall, and
cause serious injury.
• If you want to enjoy 3D content, connect
a 3D device (3D compliant AV receiver or
TV) to the player's HDMI OUT port using a
high-speed HDMI cable. Put on 3D glasses
before playing the 3D content.
• The player outputs 3D signals only through
HDMI cable connected to the HDMI OUT
port.
• As the video resolution in 3D play mode
is fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
• Some functions such as BD Wise, screen
size adjustment, and resolution adjustment
may not operate properly in 3D play mode.
• You must use a high-speed HDMI cable for
proper output of the 3D signal.
• Stay at least three times the width of the
screen from the TV when watching 3D
images. For example, if you have a 46-inch
screen, stay 138 inches (11.5 feet) from the
screen.
• Place the 3D video screen at eye level for
the best 3D picture.
• When the player is connected to some 3D
devices, the 3D effect may not function
properly.
• This player does not convert 2D content
into 3D.
• "Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of the Blu-ray Disc Association.
SAFETY INFORMATION
Warning ....................................................... 2
Precautions ................................................. 3
Using the 3D function .................................. 4
GETTING STARTED
Before using the User Manual ...................... 5
Logos of Discs the player can play .............. 5
Accessories ................................................. 7
Front Panel .................................................. 7
Rear Panel ................................................... 7
Remote Control ........................................... 8
CONNECTIONS
Connecting to a TV ...................................... 8
Connecting to an Audio System .................. 9
Connecting to a Network Router ................. 9
SETTINGS
The Setup Procedure ................................. 10
Menu Navigation ........................................ 10
Accessing the Settings Menu .................... 10
Picture Settings ......................................... 10
Sound Settings .......................................... 12
Network Settings ....................................... 13
System Settings ........................................ 14
Language Settings ..................................... 15
Security Settings........................................ 15
General Settings ........................................ 15
Support Settings .......................................15
MEDIA PLAY
Playing a Commercially Recorded Disc ...... 16
Playing Files on a USB Device ................... 16
Playing a Disc with User Recorded
Content ..................................................... 17
Using DLNA ............................................... 17
Controlling Video Playback ........................ 18
Controlling Music Playback ........................ 18
Playing Photo Contents ............................. 20
APPENDIX
Troubleshooting ......................................... 20
Specifications ............................................ 22
Contents
4
Getting Started
Before using the User Manual
Disc Types and Contents your player can play
Media Disc Type Details
VIDEO
Blu-ray Disc
3D Blu-ray Disc
BD-ROM or BD-RE/-R recorded in the BD-RE format.
DVD-VIDEO
DVD-RW
DVD-R
DVD+RW
DVD+R
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that have
been recorded and finalized, or a USB storage media containing DivX,
MKV or MP4 contents.
MUSIC
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing MP3 or WMA contents.
PHOTO
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a USB
storage media containing JPEG contents.
NOTES
`
The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
`
If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.
`
Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.
`
Your player will not play content that has been recorded on a BD-R or USB device at a bit rate that exceeds
25 Mbps.
`
Playback may not work for some types of discs, or when you use specific functions, such as angle change
and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to
this if necessary.
`
When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your player cannot play
• HD DVD
• DVD-ROM/PD/
MV, etc
• DVD-RAM
• Super Audio CD
(except CD layer)
•
DVD-RW (VR mode)
•
CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio
only, not graphics.)
• 3.9 GB DVD-R for
Authoring.
Region Code
Both players and discs are coded by region.
These regional codes must match for a disc
to play. If the codes do not match, the disc
will not play.
The Region Number for this player is
displayed on the rear panel of the player.
Disc
Type
Region
Code
Area
Blu-ray
Disc
A
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia, Central
and South Asia.
DVD-
VIDEO
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
North Korea, Mongolia
6
China
Logos of Discs the player can play
Blu-ray Disc BD-LIVE
3D Blu-ray Disc DivX
PAL broadcast System in U.K., France, Germany, etc.
Supported File Formats
Notes on the USB connection
• Your player supports USB storage media,
MP3 players, digital cameras, and USB
card readers.
• The player does not support folder or file
names longer than 128 characters.
• Some USB/External HDD/digital camera
devices may not be compatible with the
player.
• Your player supports the FAT16, FAT32,
and NTFS file systems.
• Connect USB devices directly to the
player’s USB port. Connecting through
a USB cable may cause compatibility
problems.
• Inserting more than one memory device
into a multi-card reader may cause the
reader to operate improperly.
• The player does not support the PTP
protocol.
5
Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be
played if its content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file
itself is corrupted.
- Files having a higher Bit rate/frame rate than standard may stutter during sound/video playback.
- The Seek (skip) function is not available if the file’s index table is damaged.
- Depending on your country, RMVB format may not be supported.
Video decoder
- Supports up to H.264 Level 4.1 and AVCHD
- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4
- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
- Does not support GMC 2 or higher
Audio decoder
- Supports WMA 7, 8, 9 and STD
- Does not support WMA sampling rate of 22050Hz mono.
- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)
Max bit rate: 320kbps
Supported DivX subtitle file formats
*.ttxt, *.smi, *.srt, *.sub, *.txt
NOTES
`
Playback of some DivX, MKV or MP4 file may not be supported depending on their video resolution and
frame rate.
Music File Support
File Extension Container Audio Codec Support Range
*.mp3
MP3 MP3
-
*.wma
WMA WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates from 5kbps to 355kbps
• Do not disconnect a USB device during a "loading" process.
• The bigger the image resolution, the longer the image takes to display.
• This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from
commercial sites.
• Your player only supports video with a frame rate under 30fps (frames per second).
• Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives
and USB HDD. (HUB is not supported.)
• Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with
this player.
•
If some USB devices require excessive power, they may be limited by the circuit safety device.
• If playback from a USB HDD is unstable, provide additional power by plugging the HDD into
a wall socket.
If the problem continues, contact the USB HDD manufacturer.
• SAMSUNG is not responsible for any data file damage or data loss.
• Your player does not support NTFS compressed files, sparse files, or encrypted files.
• You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)
Video File Support
File Extension Container Video Codec Audio Codec Resolution
*.avi
AVI
DivX 3.11/4/5/6
MP3
Dolby Digital
DTS
WMA
PCM
1920x1080
MP4v3
H.264 BP/MP/HP
1920x1080
*.mkv
MKV
VC-1 AP
MP3
Dolby Digital
DTS
1920x1080
H.264 BP/MP/HP
1920x1080
*.wmv
WMV (wmv9)
VC-1 AP
WMA
1920x1080
VC-1 SM
1920x1080
*.mp4
MP4
MP4 (mp4v)
AAC
1920x1080
H.264 BP/MP/HP
1920x1080
*.mpg
*.mpeg
PS
MPEG1
MP1, 2
Dolby Digital
DTS
1920x1080
MPEG2
1920x1080
H.264 BP/MP/HP
1920x1080
*.rmvb
RMVB
RV8/9/10
RV30/40
RealAudio 6
1920x1080
6
Picture File Support
File Extension Type Resolution
*.jpg
*.jpeg
*.jpe
JPEG
15360x8640
*.png
PNG
15360x8640
AVCHD (Advanced Video Codec High Definition)
• This player can play back AVCHD format discs. These discs are normally recorded and used
in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the
conventional image compressing format.
• Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs that
use "x.v.Color" format.
• "x.v.Color" is a trademark of Sony Corporation.
• "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.
and Sony Corporation.
NOTES
`
Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
`
"x.v.Color" offers a wider colour range than normal DVD camcorder discs.
Accessories
Check for the supplied accessories shown below.
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
HDMI Cable
Batteries for Remote
Control (AAA Size)
User Manual Remote Control
Front Panel
DISC TRAY
POWER BUTTON
OPEN/CLOSE BUTTON
USB HOST
REMOTE CONTROL SENSOR
NOTES
`
You can perform software upgrades using the USB Host jack with a USB flash memory stick only.
`
Please open and pull out the USB cover before inserting USB device.
Rear Panel
HDMI OUT LAN DIGITAL AUDIO OUT
7
Connections
Connecting to a TV
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your TV.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Audio
Video
NOTES
`
If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio
Out on the player to an audio system to hear audio.
`
An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.
`
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of
your TV.
`
When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the
first time, the player automatically sets the HDMI output resolution to the highest supported by the TV.
`
A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Colour to Off in the menu.
`
To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.
`
HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on
the screen.
Remote Control
Tour of the Remote Control
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
Turn the player on and off.
Allows you to repeat A-B disc.
Press numeric buttons to operate options.
Press to open and close the disc tray.
Use to enter the disc menu.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use Bonusview function.
Return to the previous menu.
These buttons are used both for menus on the
player and also several Blu-ray Disc functions.
Use to select menu items and change menu
values.
Press to use Tools menu.
Use to access various audio functions on a
disc (Blu-ray Disc/DVD).
Press to play a disc.
Press to pause a disc.
Turn the TV on and off.
Press to switch the Blu-ray Disc/DVD's
subtitle language.
Use to enter the popup menu/title menu.
Press to search a disc backwards or
forwards.
Press to move to the home menu.
Press to see the full screen on a TV.
During the Bluray disc/DVDs playback, this
button does not operate.
Press to exit the menu.
Use to display the playback information.
Allows you to repeat a title, chapter, track or
disc.
TV volume adjustment.
After setup, allows you to set the input
source on your TV.
Installing batteries
NOTES
`
If the remote does not operate properly:
•
Check the polarity (+/–) of the batteries.
•
Check if the batteries are drained.
•
Check if the remote sensor is blocked by obstacles.
•
Check if there is any fluorescent lighting nearby.
!
CAUTION
`
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash
`
Do not dispose of batteries in a fire.
`
Do not short circuit, disassemble or overheat the batteries.
`
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
8
Connecting to an Audio System
You can connect the Blu-ray player to an audio system using one of the methods illustrated
below.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Method 1 Connecting to an HDMI compatible AV receiver
• Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your receiver.
• Best quality (Recommended)
Method 2 Connecting to an AV receiver with a Digital Coaxial Cable
• Using a digital Coaxial cable (not supplied), connect the Coaxial Digital Audio Out jack on the
product to the Digital Coaxial In jack of the receiver.
• Good quality
• You will hear sound only through the front two speakers with Digital Output set to PCM.
AudioAudio
Method 2Method 1
Connecting to a Network Router
You can connect your player to your network router using one of the methods illustrated below.
To use the DLNA network functionality, you must connect your PC to your network as shown
in the illustrations.
Wired Network
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband modem
Router
Or
NOTES
`
Internet access to Samsung's software update server may not be allowed, depending on the router you use or your
ISP's policy. For more information, contact your ISP (Internet Service Provider).
`
DSL users, please use a router to make a network connection.
9
Settings
The Setup Procedure
• The Home screen will not appear if you do not
configure the setup.
• The OSD (On Screen Display) may change in this
player after you upgrade the software version.
• The access steps may differ depending on the
menu you selected.
•
After the setup process is complete, the panel
buttons and remote control can be operated.
After you have connected the player to your TV,
turn on the TV and player. When you turn on the
player the first time, the player's Setup screen
appears on the TV. The Setup procedure lets
you set the On Screen Display (OSD) and menu
languages, the aspect ratio (screen size), the
network type, and connect the player to your
network.
NOTES
`
The Home menu will not appear if you do not
configure the setup except as noted below.
`
If you press the BLUE (D) button during
network setup, you can access the Home menu
even if the network setup is not completed yet.
`
When you return to the Home menu, the full
screen mode is cancelled automatically.
`
If you want to display the Setup screen again
to make changes, press the
^
button on
the front panel of the player for more than 5
seconds with no disc inserted. This resets the
player to its default settings.
`
After the setup process is complete. you can
operate the HDMI-CEC function.
`
If you want to use the Anynet+(HDMI-CEC)
function to aid in the initial set up process,
please follow the instructions below.
1) Connect the player to an Anynet+(HDMI-
CEC) compliant Samsung TV using HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On in
both the TV and the player.
3) Set the TV to the Setup Procedure.
`
If you leave the player in the stop mode for
more than 5 minutes without using it, a screen
saver will appear on your TV. If the player is
left in the screen saver mode for more than 25
minutes, the power will automatically turn off.
Menu Navigation
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
4
3
1
HOME Button : Press to move to the Home
menu.
2
RETURN Button :
Return to the previous menu.
3
v
(Enter) / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
4
EXIT Button : Press to exit the current menu.
• Home Menu
App 1 App 2 App 3 App 4
App 5
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
2
3
6
5
7
1
4
1
Selects VIDEOS.
2
Selects MUSIC.
3
Selects Settings.
4
Selects Change Device.
5
Selects PHOTOS.
6
Selects PLAY DISC.
7
Selects applications.
NOTES
`
The Videos, Photos, and Music options require
that you have an appropriate disc inserted into
the player or a USB flash device attached to
the player.
Accessing the Settings Menu
To access the Settings menu and sub-menus,
follow these steps:
1. Press the POWER button.
The Home Menu appears.
2.
Press the
▲▼
◄► buttons to select
Settings, and then press the
v
button.
3. Press the ▲▼ buttons to select the desired
submenu, and then press the
v
button.
4.
Press the ▲▼ buttons to select the desired
item, and then press the
v
button.
5. Press the EXIT button to exit the menu.
NOTES
`
The access steps may differ depending on
the menu you selected. The OSD (On Screen
Display) may change in this player after you
upgrade the software version.
Picture Settings
You can configure various display options
such as the TV Aspect Ratio, Resolution, etc.
3D Settings
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
10
NOTES
`
For some 3D discs, to stop a movie during 3D
playback, press the
5
button once.
The movie stops and the 3D mode option is de-
activated.
To change a 3D option selection when you are
playing a 3D movie, press the
5
button once.
The Blu-ray menu appears. Press the
5
button
again, then select 3D Settings in the Blu-ray menu.
`
Depending on the content and the position of the
picture on your TV screen, you may see vertical
black bars on the left side, right side, or both
sides.
TV Aspect Ratio
Depending on the type of television you have,
you may want to adjust the screen size setting.
NOTES
`
Depending on the disc type, some aspect
ratios may not be available.
`
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
the picture might appear to be distorted.
BD Wise (Samsung TVs only)
BD Wise is Samsung’s latest inter-connectivity
feature.
When you connect a Samsung player and a
Samsung TV with BD Wise to each other via
HDMI, and BD Wise is on in both the player
and TV, the player outputs video at the video
resolution and frame rate of the Blu-ray Disc/
DVDs.
NOTES
`
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
`
If the player is connected to a device that does not
support BD Wise, you cannot use the BD Wise function.
`
For proper operation of BD Wise, set the BD
Wise menu of both the player and the TV to On.
Resolution
Lets you set the output resolution of the HDMI
video signal to Auto, 1080p, 1080i, 720p or
576p/480p. The number indicates the number
of lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively.
The more lines, the higher the quality.
Resolution according to the output
mode
• Blu-ray Disc/E-contents/Digital Contents
playback
Output
Setup
HDMI / connected
HDMI Mode
Blu-ray Disc
E-contents/
Digital
contents
BD Wise
Resolution of
Blu-ray Disc
1080p
Auto
Max. Resolution
of TV input
Max. Resolution
of TV input
1080p@60F
(Movie Frame : Off)
1080p@60F 1080p@60F
Movie Frame :
Auto (24 fps)
1080p@24F 1080p@24F
1080i 1080i 1080i
720p 720p 720p
576p/480p 576p/480p 576p/480p
• DVD playback
Output
Setup
HDMI / connected
HDMI Mode
BD Wise 576i/480i
Auto Max. Resolution of TV input
1080p 1080p
1080i 1080i
720p 720p
576p/480p 576p/480p
NOTES
`
If the TV you connected to the player does
not support Movie Frame or the resolution
you selected, the message "If no pictures are
shown after selecting ‘Yes’, please wait for 15
seconds to return to the previous resolution."
apprears. If you select Yes, the TV’s screen
will go blank for 15 seconds, and then the
resolution will revert to the previous resolution
automatically.
`
If the screen stays blank after you have
changed the resolution, remove all discs,
and then press and hold the
^
button on the
front of the player for more than 5 seconds.
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display
Setup that your TV will support.
`
When the factory default settings are restored,
all stored user BD data is deleted.
`
The Blu-ray Disc must have the 24 frame
feature for the player to use the Movie Frame
(24 fps) mode.
Movie Frame (24 fps)
Setting the Movie Frame (24 fps) feature to
Auto allows you to adjust the player’s HDMI
output to 24 frames per second for improved
picture quality.
You can enjoy the Movie Frame (24 fps)
feature only on a TV supporting this frame
rate. You can select Movie Frame only when
the player is in the HDMI 1080p output
resolution modes.
HDMI Colour Format
Lets you set the colour space format for
HDMI output to match the capabilities of the
connected device (TV, monitor, etc).
HDMI Deep Colour
Lets you output video from the HDMI OUT
jack with Deep Colour. Deep Colour provides
more accurate colour reproduction with
greater colour depth.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
11
Sound Settings
Digital Output
Lets you select the digital audio output format that is suitable for your TV or AV Receiver. For
more details, please refer to the Digital Output Selection table.
Digital Output Selection
Setup PCM
Bitstream
(Unprocessed)
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
Connection
HDMI
Receiver
Coaxial
HDMI
Receiver
Coaxial
HDMI Receiver or
Coaxial
HDMI supported
AV receiver or
Coaxial
Audio Stream
on Blu-ray
Disc
PCM Up to 7.1ch PCM 2ch PCM PCM 2ch Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby Digital Plus PCM 2ch PCM 2ch
Dolby Digital
Plus
Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
Dolby TrueHD PCM 2ch PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS
Re-encoded
Dolby Digital *
DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD High
Resolution Audio
PCM 2ch PCM 2ch
DTS-HD High
Resolution
Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
DTS-HD Master
Audio
PCM 2ch PCM 2ch
DTS-HD
Master Audio
DTS Re-encoded DTS
Re-encoded
Dolby Digital *
Audio Stream
on DVD
PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Dolby Digital Dolby Digital
DTS PCM 2ch PCM 2ch DTS DTS DTS DTS
Definition for
Blu-ray Disc
Any
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio and add
Navigation Sound Effects.
Outputs only main feature
audio stream so that your
AV receiver can decode the
audio bitstream.
You will not hear BONUSVIEW
audio and Navigation Sound
Effects.
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio
and add Navigation
Sound Effects, then
re-encodes the
PCM audio into DTS
bitstream
Decodes main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and add
Navigation Sound
Effects, then re-
encodes the PCM
audio into Dolby
Digital bitstream
* If Source Stream is 2ch, "Re-encoded
Dolby D" Settings are not applied.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack
of the main feature.
- BONUSVIEW audio : An additional
soundtrack such as the director or actor’s
commentary.
- Navigation Sound Effects : When you
choose a menu navigation selection, a
Navigation Sound Effect may sound.
Navigation Sound Effects are different on
each Blu-ray Disc.
NOTES
`
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
`
If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
`
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
`
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
`
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
`
If your TV is not compatible with compressed
multi-channel formats (Dolby Digital, DTS), the
player may output PCM 2ch downmixed audio
even though you selected Bitstream (either Re-
encoded or Unprocessed) in the setup menu.
`
If your TV is not compatible with PCM sampling
rates over 48kHz, the player may output 48kHz
downsampled PCM audio even though you set
PCM Downsampling to Off.
PCM Downsampling
Lets you choose to have 96KHz PCM signals
downsampled to 48KHz before they are
outputted to an amplifier. Choose On if your
amplifier or receiver is not compatible with a
96KHz signal.
Dynamic Range Control
Lets you apply dynamic range control to
Dolby Digital, Dolby Digital Plus, and Dolby
TrueHD audio.
• Auto : Automatically controls the dynamic
range of Dolby TrueHD audio, based
on information in the Dolby TrueHD
soundtrack.
Also turns dynamic range control on for
Dolby Digital and Dolby Digital Plus.
• Off :
Leaves the dynamic range uncompressed,
letting you hear the original sound.
• On : Turns dynamic range control on for
all three Dolby formats. Quieter sounds
are made louder and the volume of loud
sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix
method that is compatible with your stereo
system. You can choose to have the player
downmix to normal stereo or to surround
compatible stereo.
12
Network Settings
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic
- and most are - we recommend using the
Auto procedure for network setup. This is
easiest and will work in the majority of cases.
If it is static, you must use the manual set up
procedure.
Network setup directions start below.
NOTES
`
This unit can only be connected to a Network
via a wired connection.
Wired Network Settings
1. In the Home menu, press the ▲▼ ◄►
buttons to select Settings, and then
press the
v
button.
2. Press the ▲▼ buttons to select Network,
and then press the
v
button.
3. Press the ▲▼ buttons to select Wired
Network Settings, and then press the
v
button. The Wired Network Settings
screen appears.
Picture
Sound
Network
System
Language
Security
General
Support
Settings
Wired Network Settings
Internet Protocol Setup : Auto
\
IP Address :
0
0
0
0
Subnet Mask :
0
0
0
0
Gateway :
0
0
0
0
DNS : Auto
DNS Server :
0
0
0
0
>
Move
"
Select
'
Return
4. In the Internet Protocol Setup field, select
Auto if it is not selected. (Press
v
select
Auto, and then press
v
.)
5. The Auto Function acquires and fills in the
values for IP Address, Subnet Mask,
etc., automatically.
NOTES
`
This process can take up to five minutes.
6. After the Network Function has acquired
the network values, press the RETURN
button.
7. Select Network Test, and then press
v
to ensure the player has connected to
your network.
8. When the Network Test is complete, press
the RETURN twice to return to the Main
Menu.
9. If the Network Function does not acquire
the network values, go to the directions
for Manual Setup.
Manual Network Settings
Before you start manual network setup, you
need the network setting values.
To enter the Network Settings into your
player, follow these steps:
1. In the Home menu, press the ▲▼ ◄►
buttons to select Settings, and then
press the
v
button.
2. Press the ▲▼ buttons to select Network,
and then press the
v
button.
3. Press the ▲▼ buttons to select Wired
Network Settings, and then press the
v
button. The Wired Network Settings
screen appears.
4. Select the Internet Protocol Setup field,
and then press the
v
button.
5. Press the ▲▼ buttons to select Manual,
and then press the
v
button.
6. Press the ▼ button to go to the first entry
field (IP Address).
7. Use the number buttons on your remote
to enter numbers.
8. When done with each field, use the ►
button to move to the next field. You can
also use the other arrow buttons to move
up, down, and back.
9. Enter the IP Address, Subnet Mask, and
Gateway values in the same way.
10. Press the ▼ button to go to DNS.
11. Press the ▼ button to go to the first DNS
entry field.
12. Enter the numbers as above.
13. Press the RETURN button on your
remote.
14. Run a Network Test to ensure the player
has connected to your network.
Network Test
Use this menu item to check whether your
network connection is working or not.
Network Status
Use to check whether a connection to
a network and the Internet has been
established.
Device Name
Device Name function allows you to change
player's name by selecting from device
name list.
BD-Live Internet Connection
Set to allow or prohibit an Internet
connection when you use the BD-LIVE
service.
•
Allow (All) : The Internet connection is
allowed for all BD-LIVE contents.
•
Allow (Valid Only) : The Internet
connection is allowed only for BD-LIVE
contents containing a valid certificate.
•
Prohibit : No Internet connection is
allowed for any BD-LIVE content.
13
NOTES
`
What is a valid certificate?
When the player uses BD-LIVE to send
the disc data and a request to the server
to certify the disc, the server uses the
transmitted data to check if the disc is valid
and sends the certificate back to the player.
`
The Internet connection may be restricted
while you are using BD-LIVE contents.
Using BD-LIVE™
Once the player is connected to the
network, you can enjoy various movie-
related service contents using a BD-LIVE
compliant disc.
1.
Attach a USB memory stick to the
USB jack on the front of the player, and
then check its remaining memory. The
memory device must have at least 1GB
of free space to accommodate the BD-
LIVE services.
2.
Insert a Blu-ray Disc that supports BD-
LIVE.
3.
Select an item from various BD-LIVE
service contents provided by the disc
manufacturer.
NOTES
`
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
The DLNA Function
DLNA lets you play music, video, and photo
files located in your PC on the player.
To use DLNA with your player, you must
connect the player to your network.
(See page 13-14).
To use DLNA with your PC, you must install
DLNA software on your PC.
System Settings
Setup
By using the Setup function, you can set
the language, Network Settings, etc.
For more information about the Setup
function, refer to the Setup section of this
user manual (See page 10).
Quick Start
You can turn on the power quickly by
decreasing the boot time.
NOTES
`
If this function is set to On, Standby power
consumption will be increased.
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers
linked operations with other Samsung players
that have the Anynet+ feature.
To operate this function, connect this player to
an Anynet+ Samsung TV with an HDMI cable.
With Anynet+ on, you can operate this player
using a Samsung TV remote control and start
disc playback simply by pressing the PLAY
(
) button on the TV’s remote control.
For more information, please see the TV user
manual.
NOTES
`
This function is not available if the HDMI cable
does not support CEC.
`
If your Samsung TV has an Anynet+ logo, then
it supports the Anynet+ function.
`
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
`
After the product was turned off, disconnecting
and connecting the power cable turns it on
automatically. At the moment, it automatically
turns off in about 15 seconds for re-
establishing Anynet+ connection.
`
For some TV products, if connected to this
product with Anynet+ function, turning the
TV on may display a warning popup message
saying no connection was found. Still, Anynet+
connection is properly established and
available to use.
BD Data Management
Enables you to manage the downloaded
contents you accessed through a Blu-ray
disc that supports the BD-LIVE service and
stored on a flash drive.
You can check the device’s information
including the storage size, delete the BD
data, or change the Flash memory device.
NOTES
`
In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
`
Your player supports the FAT16, FAT32, and
NTFS file systems. We recommend you use
USB devices that support USB 2.0 protocol
with 4 MB/sec or faster read/write speed.
`
The Resume Play function may not work after
you format the storage device.
`
The total memory available to BD Data
Management may differ, depending on the
conditions.
DivX® Video On Demand
View DivX® VOD Registration Codes to
purchase and play DivX® VOD contents.
14
Language Settings
You can select the language you prefer for
the On-Screen menu, disc menu, audio, and
subtitles.
NOTES
`
The selected language will only appear if it
is supported on the disc.
Security Settings
The default security PIN is 0000. Enter the
default PIN to access the security function
if you haven't created your own PIN. After
you have accessed the security function
for the first time, change the PIN using the
Change PIN function.
BD Parental Rating
Prevents playback of Blu-ray Discs with
specific age ratings unless the 4 digit PIN is
entered.
DVD Parental Rating
This function works in conjunction with
DVDs that have been assigned an age
rating or numeric rating that indicates
the maturity level of the content. These
numbers help you control the types of
DVDs that your family can watch.
Select the rating level you want to set.
For example, if you select Level 6, discs
rated above 6 - Level 7 and 8 - will not play.
A larger number indicates more mature
content.
Change PIN
Change the 4-digit password used to
access security functions.
If you forget your password
1.
Remove any discs.
2.
Press and hold the
^
button on the
front panel for 5 seconds or more.
All settings will revert to the factory
settings.
NOTES
`
When the factory default settings are
restored, all the user stored BD data will be
deleted.
General Settings
Time Zone
Lets you specify the time zone that is
applicable to your area.
Support Settings
Software Upgrade
The Software Upgrade menu allows
you to upgrade the player’s software for
performance improvements or additional
services.
By Online
To upgrade By Online, follow these steps:
1.
In the player’s menu, go to Settings >
Support > Software Upgrade.
2.
Select By Online, and then press the
v
button. The Connecting to Server
message appears.
3.
A popup message will appear if an
update is available.
4.
If you select Yes, download process
started. (Never turn the player on during
an upgrade.)
5.
When the update is completed, the
player will restart automatically.
NOTES
`
The upgrade is complete when the player
turns off, and then turns on again by itself.
`
Never turn the player off or back on manually
during the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused
by an unstable Internet connection or
consumer negligence during a software
upgrade.
`
No disc should be in the product when you
upgrade the software By Online.
By USB
To upgrade by USB, follow these steps:
1.
Visit www.samsung.com/bluraysupport.
2.
Download the latest USB software
upgrade zip archive to your computer.
3.
Unzip the zip archive to your computer.
You should have a single RUF file with
the same name as the zip file.
4.
Copy the RUF file to a USB flash drive.
5.
Make sure there is no disc in the player,
and then insert the USB flash drive into
the USB port of the player.
6.
In the player’s menu, go to Settings >
Support > Software Upgrade.
7.
Select By USB.
NOTES
`
No disc should be in the product when you
upgrade the software using the USB Host
jack.
`
When the software upgrade is done, check
the software details in the software Upgrade
menu.
`
Do not turn off the player during the
software upgrade. It may cause the player to
malfunction.
`
Software upgrades using the USB Host jack
must be performed with a USB flash memory
stick only.
15
Auto Upgrade Notification
If you have connected the player to your
network, and then set Auto Upgrade
Notification on, the player automatically
notifies you when a new software version is
available for the player.
To set Auto Upgrade Notification on, follow
these steps:
1.
Select Auto Upgrade Notification, and
then press the
v
button.
2.
Use the ▲▼ buttons to select On, and
then press the
v
button.
If there is a new software version available,
the player notifies you with a popup
message.
1.
To upgrade the firmware, select Yes
in the Pop-up. The player turns off
automatically, then restarts, and begins
the download. (Never turn the player on
or off manually during an upgrade.)
2.
The update progress popup appears.
3.
When the update is completed, the
player will restart automatically.
NOTES
`
The upgrade is complete when the player
turns off, and then turns on again by itself.
`
Never turn the player off or on manually
during the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused
by an unstable Internet connection or
consumer negligence during software
upgrade.
Contact Samsung
Provides contact information for assistance
with your player.
Terms of Service Agreement
Lets you view the general disclaimer
regarding third party contents and services.
Reset
Returns all settings to their factory defaults
except for the network settings.
Media Play
Playing a Commercially Recorded
Disc
1. Press the
8
button to open the disc tray.
2. Place a disc gently into the disc tray with
the disc's label facing up.
3. Press the
8
button to close the disc tray.
Playback starts automatically.
Playing Files on a USB Device
There are two methods you can use to play or
view multimedia files located on a USB device
through your player.
Method 1
1. Turn the player on.
2. Connect the USB device to the USB port
on the front panel of the player. The New
Device Connected pop-up appears.
App 1 App 2 App 3 App 4 App 5
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
New device connected.
Photos
Videos
Music
123
>
Move
"
Enter
'
Return
NOTES
`
If the pop-up does not appear, go to Method 2.
3.
Use the ▲▼ buttons to select Photos,
Videos or Music, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
3. For example, if you selected music, you
will only be able to see music files. You can
change this selection by returning to the
Photos, Videos & Music screen and going to
Step 3 in Method 2 below.
4.
If necessary, use the ▲▼◄► buttons
to select a folder, and then press the
v
button.
5.
Select a file to view or play, and then
press the
v
button.
6.
Press the RETURN button to exit a
folder or the EXIT button to return to
the Home screen.
7.
Go to pages 18~20 for instructions
that explain how to control playback of
videos, music, and pictures on a USB
device.
16
Method 2
1. Turn the player on.
2. Connect the USB device to the USB port
on the front panel of the player. Select
Change Device and then press the ▲▼
button to select USB. Press the
v
button.
App 1 App 2 App 3 App 4 App 5
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
Change Device
No Disc
123
a
Close
3.
Use the ▲▼◄► buttons to select
PHOTOS, VIDEOS or MUSIC on the
Home screen, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
3. For example, if you selected music, you
will only be able to see music files. You
can change this selection by returning to
the Photos, Videos & Music screen and
repeating Step 3.
4.
If necessary, use the ▲▼◄► buttons
to select a folder, and then press the
v
button.
5.
Use the ▲▼◄► buttons to select a file
to view or play, and then press the
v
button.
6.
Press the RETURN button to exit a
folder or the EXIT button to return to
Home screen.
7.
Go to pages 18~20 for instructions
that explain how to control playback of
videos, music, and pictures on a USB
device.
NOTES
`
If you insert a disc when playing a USB
device, the device mode changes to "Disc"
automatically.
Playing a Disc with User Recorded
Content
You can play multimedia files you have
recorded on Blu-ray, DVD, or CD discs.
1.
Place a user recorded disc into the disc
tray with the disc’s label facing up, and
then close the tray.
2.
Use the ◄► buttons to select the type
of content you want to view or play -
VIDEOS, PHOTOS, or MUSIC - and
then press the
v
button.
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
2. For example, if you selected music, you
will only be able to see music files. You can
change this selection by returning to the
Home screen and repeating Step 2.
3.
A screen appears listing the contents
of the disc. Depending on how the
contents are arranged, you will see
either folders, individual files, or both.
4.
If necessary, use the ▲▼◄► buttons
to select a folder, and then press the
v
button.
5.
Use the ◄►▲▼ buttons to select a file
to view or play, and then press the
v
button.
6.
Press the RETURN button one or more
times to exit a current screen, exit a
folder, or to return to the Home screen.
Press the EXIT button to return directly
to the Home Screen.
7.
Go to pages 18~20 for instructions
that explain how to control playback of
videos, music, and pictures on a disc.
Using DLNA
DLNA Connection
PC
Blu-ray Disc Player
Play back PC's
files
1. Connect the Blu-ray Disc Player, your PC,
and/or your DLNA compatible device to
the same network.
2.
Follow the directions in the DLNA
software Installation/Instruction manual
to set up devices and files for playing or
viewing.
3.
Select Change Device on the player's
Home screen, and then press the
v
button. In the list of DLNA connected
devices that appears, select your PC
or other DLNA compatible device, and
then press the
v
button.
4.
Use the ◄► buttons to select the type
of content you want to view or play -
VIDEOS, PHOTOS, or MUSIC - and
then press the
v
button.
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
4. For example, if you selected music, you
will only be able to see music files. You can
change this selection by returning to the
Home screen and repeating Step 4.
5.
A screen appears listing the contents
of the PC or DLNA device. Depending
on how the contents are arranged, you
will see either folders, individual files, or
both.
6.
If necessary, use the ▲▼◄► buttons
to select a folder, and then press the
v
button.
7.
Use the ◄►▲▼ buttons to select a file
to view or play, and then press the
v
button.
17
8. Press the RETURN button one or more
times to exit a current screen, exit a folder,
or to return to the Home screen. Press the
EXIT button to return directly to the Home
Screen.
9. Go to pages 18~20 for instructions that
explain how to control playback of videos,
music, and pictures on a disc.
Controlling Video Playback
You can control the playback of video
content located on a Blu-ray disc, DVD,
CD, USB device, or your computer.
Depending on the media, some of the
functions described in this manual may not
be available.
During Blu-ray or DVD disc playback, the
Full screen button does not operate.
Buttons on the Remote Control
used for Video Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
2
Playback related buttons
The player does not play sound in Search,
Slow or Step mode.
• To return to normal speed playback, press
the
6
button.
6
button
Starts playback.
5
button
Stops playback.
7
button
Pauses playback.
Fast Motion
Play
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button, the playback speed
will change.
Slow Motion
Play
In pause mode, press the
4
button.
Each time you press the
4
button, the playback speed will
change.
Step Motion
Play
In pause mode, press the
7
button.
Each time you press the
7
button, a new frame appears.
Skip Motion
Play
During playback, press the
1
or
2
button.
Each time you press the
1
or
2
button, the disc moves to the
previous or next chapter or file.
Using the disc menu, title menu,
popup menu, and title list
DISC MENU
button
During playback, press this button
to start the disc menu function.
TITLE MENU
button
During playback, press this button
to start the title menu function.
POPUP MENU
button
During playback, press this button
to start the popup menu function.
Controlling Music Playback
You can control the playback of music located
on a Blu-ray disc, DVD, CD, USB device, or
your computer.
Buttons on the Remote Control
used for Music Playback
SCREEN
A-BVIEW
FULLBONUS REPEAT REPEAT
AUDIO HOME SUBTITLE
1
4
6
3
2
5
1
NUMBER buttons (Audio CD (CD-DA) only) :
During Playlist playback, press the desired
track number.
The selected track is played.
2
Skip : During playback, press the
1
or
2
button to move to the previous or next file of
the playlist.
3
5
button : Stops a track.
4
Fast Play (Audio CD (CD-DA) only)
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button,
the playback speed will change.
5
Pause : Pauses a track.
6
6
button : Plays the currently selected
track.
Repeat an Audio CD (CD-DA)/
MP3
1. During Playlist playback, press the
TOOLS button.
"
Pause c Select Tools
'
Return
+
00:08 / 05:57
1/6
TRACK 001
05:57
TRACK 002
04:27
TRACK 003
04:07
TRACK 004
03:41
TRACK 005
03:17
TRACK 006
03:35
Playlist
TRACK 001
CD
Tools
Repeat Mode ? Off \
Rip
>
Move
<
Adjust
'
Return
2. Press the ◄► buttons to select Track,
All, Shuffle, or Off.
3. Press the
v
button.
Off
Songs are played in the order
in which they were recorded.
(
) Track
The current song is repeated.
(
) All
All songs are repeated.
(
) Shuffle
Shuffle plays songs in random
order.
18
Playlist
1.
To move to the Music List, press the
5
or RETURN button.
The Music List screen appears.
c
Select Tools
( )
Jump to Page
'
Return
1/2 Page
Music
TRACK 001
TRACK 001
02:38
TRACK 003
02:38
TRACK 005
02:38
TRACK 007
02:38
TRACK 009
02:38
TRACK 004
02:38
TRACK 002
02:38
TRACK 006
02:38
TRACK 008
02:38
TRACK 010
02:38
CD a Change Device
2.
Press the ▲▼◄► buttons to move
to a desired track, and then press the
YELLOW (C) button. A check appears
on the track.
Repeat this procedure to select
additional tracks.
3.
To remove a track from the list, move to
the track, and then press the YELLOW
(C) button again.
The check on the track is cancelled.
4.
When done, press the
v
button.
The tracks you selected are displayed
on the right side of the screen. The
player plays the first track.
5.
To change the play list, press the
5
button or RETURN button to return to
the Music List. Repeat Steps 2, 3, and 4.
6. To cancel the play list and return to the
Home screen, press the RETURN or EXIT
button.
NOTES
`
You can create a playlist with up to 99 tracks
on Audio CDs (CD-DA).
`
If you remove all the tracks from a play list
and then press the
v
button, the player
lists and plays all the tracks on the disc.
Ripping
Lets you copy audio files contents from an
Audio CD (CD-DA) to USB/HDD device.
1.
Open the disc tray. Place the audio (CD-
DA) disc on the tray, and close the tray.
Insert a USB device into the USB jack
on the front of the product.
2.
In Stop mode, press the ▲▼◄►
buttons to move to a desired track, and
then press the YELLOW (C) button. A
check appears on the track.
Repeat this procedure to select
additional tracks.
3.
To remove a track from the list, move to
the track, and then press the YELLOW
(C) button again.
The check on the track is cancelled.
4.
When done, press the TOOLS button
and then select the Rip using the ▲▼
buttons. and then press the
v
button.
The Rip pop-up appears.
5.
Use the ▲▼ buttons to select the
device to store the ripped files, and then
press the
v
button.
NOTES
`
Do not disconnect the device while ripping is
in progress.
6.
If you want to cancel ripping, press the
v
button and then select Yes. Select
No to continue ripping.
7.
When ripping is complete, the "Ripping
completed." message appears. Press
the
v
button to go back to the
Playback screen.
NOTES
`
This function may not be supported by some
discs.
`
On the Ripping screen, you can also choose
Select All and Deselect All.
-
Use Select All to select all tracks. This
cancels your individual track selections.
-
Use Deselect All to deselect all selected
tracks at once.
Disc Copy to USB
Lets you copy video/photo/music contents
from data Disc to USB/HDD device.
1.
Open the disc tray. Place the data disc
on the tray, and close the tray. Insert a
USB device into the USB jack on the
front of the product. The new device
pop-up appears.
2.
Press the ▲ button, and then press the
◄► buttons to select Blu-ray, DVD or
CD.
3.
Use the ▲▼ buttons to select Photos,
Videos or Music, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of the
device. Depending on how the contents
is arranged, you will see either folders,
individual files, or both.
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
3. For example, if you selected music, you
will only be able to see music files. You
can change this selection by returning to
the Photos, Videos & Music screen and
repeating Step 3.
4.
In Stop mode, use the ▲▼◄► buttons
to select the VIDEOS, PHOTOS, or
MUSIC, and then press the YELLOW
(C) button. A check appears to the left
of the desired item.
5.
Repeat Step 4 to select and check
additional desired item.
6.
To remove the desired item from the list,
press the YELLOW (C) button again.
The check on the desired item is
removed.
19
7.
When done, press the TOOLS button
and then select the Copy to USB using
the ▲▼ buttons. and then press the
v
button. The Copy to USB pop-up
appears.
8.
Use the ▲▼ buttons to select the
device to store the copied files, and
then press the
v
button.
NOTES
`
Do not disconnect the device while copying
is in progress.
9.
If you want to cancel copying, press the
v
button and then select Yes. Select
No to continue copying.
10.
When copying is complete, the
"Copying completed." message
appears. Press the
v
button to go
back to the Playback screen.
NOTES
`
This function may not be supported by some
discs.
`
On the Copying screen, you can also choose
Select All and Deselect All.
-
Use Select All to select all item. This
cancels your individual item selections.
-
Use Deselect all to deselect all selected
item at once.
Playing Photo Contents
You can control the playback of photo content
located on a Blu-ray disc, DVD, CD, USB
device, or your computer.
Using the Tools Menu
During playback, press the TOOLS button.
Start Slide Show/
Stop Slide Show
Select to start or stop the slide
show.
Slide Show Speed
Select to set a slide show's speed.
Background
Music
Select to listen to music while
viewing a slide show.
Zoom
Select to enlarge the current
picture. (Enlarge up to 4 times)
Rotate
Select to rotate the picture. (This
will rotate the picture either
clockwise or counter clockwise.)
Information
Shows the picture information.
NOTES
`
Depending on the disc or storage device, the
Tools menu may differ.
`
To enable the background music function, the
photo file must be in the same storage media
as the music file.
However, the sound quality can be affected
by the bit rate of the MP3 file, the size of the
photo, and the encoding method.
`
You can't enlarge the subtitle and PG graphic
in the full screen mode.
Appendix
Troubleshooting
Before requesting service, please try the following solutions.
PROBLEM SOLUTION
No operation can be
performed with the remote
control.
• Check the batteries in the remote control. They may need replacing.
• Operate the remote control at a distance of no more than 6.1m from the
player.
• Remove batteries and hold down one or more buttons for several minutes
to drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
Disc does not play. • Ensure that the disc is installed with the label side facing up.
• Check the region number of the Blu-ray Disc/DVD.
Disc Menu does not appear. • Ensure that the disc has disc menus.
The prohibition message
appears on the screen.
• This message appears when an invalid button is pressed.
• The Blu-ray Disc/DVD’s software doesn’t support the feature (e.g., angles).
•
You’ve requested a title or chapter number or search time that is out of range.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work properly if
the disc is not encoded with the corresponding function.
The screen ratio cannot be
changed.
• The Screen Ratio is fixed on your Blu-ray Disc/DVD.
• This is not a problem with the player.
No audio. • Make sure you have selected the correct Digital Output in the Audio Options
Menu.
The screen is blank. • If the HDMI output is set to a resolution your TV cannot support (for example,
1080p), you may not see a picture on your TV.
• Press the
^
button (on front panel) for more than 5 seconds with no disc
inside. All settings will revert to the factory settings.
• When the factory default settings are restored, all stored user BD data is
deleted.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Samsung BD-J5500 ユーザーマニュアル

カテゴリー
ブルーレイプレーヤー
タイプ
ユーザーマニュアル

他の言語で